CXA3205N All Band TV Tuner IC with On-chip PLL Description The CXA3205N is a monolithic TV tuner IC which integrates local oscillator and mixer circuits for VHF band, local oscillator and mixer circuits for UHF band, an IF amplifier and a tuning PLL onto a single chip, enabling further miniaturization of the tuner. The PLL on this IC supports the I2C bus format. Features • Low noise figure • Low power consumption (5 V, 58 mA typ.) • On-chip tuning PLL (I2C bus format) • Selection of frequency steps 31.25 kHz, 50 kHz and 62.5 kHz • On-chip 4-output band switch • IF balanced output Applications • TV tuners • VCR tuners • CATV tuners Structure Bipolar silicon monolithic IC 30 pin SSOP (Plastic) Absolute Maximum Ratings (Ta = 25 °C) • Supply voltage VCC1,VCC2 –0.3 to +5.5 VCC3 –0.3 to +10.0 • Storage temperature Tstg –55 to +150 • Allowable power dissipation PD 880 V V °C mW (when mounted on a substrate) Operating Conditions • Supply voltage VCC1, VCC2 VCC3 • Operating temperature Topr 4.75 to 5.30 4.75 to 9.45 V V –25 to +75 °C Note) Electrostatic discharge strength is weak, and care should be taken in handling this IC. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. —1— E97903-TE CXA3205N Block Diagram and Pin Configuration SCL 1 SDA 2 ADSW 3 FMT 4 BVL 5 BVH 6 Shift Register I2C BUS Receiver Divider 1/512,640,1024 REF OSC Phase Detector Charge Pump Band SW Driver LOCK Det Divider 14/15bit BU 7 USW Prescaler 1/8 VCC1 8 V.REG Bias Buffer 9 MIXout2 10 GND1 11 BYP 12 VHFin 13 Buffer UHFin2 15 UHF OSC VHF MIX Buffer UHFin1 14 VCC3 29 REFOSC 28 CPO 27 CPE 26 LOCK 25 IF OUT1 24 IF OUT2 23 GND2 IF AMP MIXout1 30 UHF MIX —2— VHF OSC 22 VCC2 21 UOSC2 20 MS 19 UOSC1 18 VOSC2 17 GND 16 VOSC1 CXA3205N Pin Description Pin No. Symbol Pin voltage (V) Equivalent circuit 22 Description VCC2 100k 5k 1 1 SCL 22 — Clock input. — Data I/O. VCC2 100k 5k 2 2 SDA 22 VCC2 150k 3 ADSW Address selection. This pin controls bits 2 and 1 of (when open) the address byte. 1.25 3 50k 4 FMT VCC3 30 5 BVL 20k 4 ON : 4.9 OFF : 0 5 6 6 BVH 7 4 : Output for FM TRAP. 5 : Power supply output for VL band. 6 : Power supply pin for VH band. 7 : Power supply output for UHF band. 7 BU The pin corresponding to the selected band goes High. 8 VCC1 Analog circuit power supply. 9 MIXout1 10 9 Mixer outputs. 10 MIXout2 11 GND1 — — —3— Analog circuit GND. CXA3205N Pin No. Symbol Pin voltage (V) Equivalent circuit Description VCC2 12 BYP 3.0 VHF input GND and FMT/BU (when open) data switching. 80k 20k 120k 13 VHFin 13 14 12 14 UHFin1 15 3k 15 3k UHFin2 18 16 VOSC1 VCC1 8p 3k 18 VOSC2 17 GND 16 8 50k 3k 15p 19 19 50 21 UOSC1 VCC1 3k UOSC2 UHF inputs. The input method can be selected from balanced input or unbalanced input. External resonance circuit connection for VHF oscillator. GND External resonance circuit connection for UHF oscillator. Frequency step mode selection. 1.5 Five modes can be selected (when open) according to the applied voltage. 120k MS VHF input. The input format is unbalanced input. VCC2 22 20 3.2 (VHF) 2.9 (UHF) 3.2 (VHF) 2.9 (UHF) 3k 21 2.3 (VHF) 0 (UHF) 0 (VHF) 2.3 (UHF) 0 (VHF) 2.3 (UHF) 3 (VHF) 3.1 (UHF) 4.0 (VHF) 5.0 (UHF) — 20 50k —4— CXA3205N Pin No. 22 23 Symbol Equivalent circuit VCC2 GND2 — — Pin voltage Description (V) — PLL circuit power supply. — PLL circuit GND. VCC1 8 24 3.0 IFOUT2 15 24 15 IF outputs. 25 25 3.0 IFOUT1 VCC2 22 5.0 (Lock) 40k 26 26 LOCK 0.2 (UNLock) VCC2 27 22 CPE LOCK detection. High when locked, Low when unlocked. 0.6 NPN transistor connection for varicap diode drive. 2.0 Charge pump output. Connect a loop filter. 4.3 Crystal connection for reference oscillator. — Power supply for external supply. 200 28 500 28 27 CPO 20k 60k 30p 29 REFOSC 30 VCC3 30p 29 —5— CXA3205N Electrical Characteristics Circuit Current Item Circuit current A Symbol AICCV AICCU Circuit current D DICC See the Electrical Characteristics Measurement Circuit. (VCC=5 V, Ta=25 °C) Measurement conditions VCC1 current, Band switch output open during VHF operation VCC1 current, Band switch output open during UHF operation VCC2 current Min. Typ. Max. Unit 36 47 61 mA 37 48 62 mA 7 11 15 mA Measurement conditions VHF operation fRF = 55 MHz VHF operation fRF = 360 MHz UHF operation fRF = 360 MHz UHF operation fRF = 800 MHz VHF operation fRF = 55 MHz VHF operation fRF = 360 MHz UHF operation fRF = 360 MHz UHF operation fRF = 800 MHz VHF operation fD = 55 MHz, fUD = ±12 MHz VHF operation fD = 360 MHz, fUD = ±12 MHz UHF operation fD = 360 MHz, fUD = ±12 MHz UHF operation fD = 800 MHz, fUD = ±12 MHz 50 Ω load saturation output VHF operation fOSC = 100 MHz ∆f from 3 s to 3 min after switch ON VHF operation fOSC = 405 MHz ∆f from 3 s to 3 min after switch ON UHF operation fOSC = 405 MHz ∆f from 3 s to 3 min after switch ON UHF operation fOSC = 845 MHz ∆f from 3 s to 3 min after switch ON VHF operation fOSC = 100 MHz ∆f when VCC 5 V changes ±5 % VHF operation fOSC = 405 MHz ∆f when VCC 5 V changes ±5 % UHF operation fOSC = 405 MHz ∆f when VCC 5 V changes ±5 % UHF operation fOSC = 845 MHz ∆f when VCC 5 V changes ±5 % Min. 24 25 29 30 Typ. 28 29 33 34 12 11 8.5 9.5 Max. 31 32 36 37 15 14 12.5 13.5 Unit dB dB dB dB dB dB dB dB 97 101 dBµ 96 100 dBµ 92 96 dBµ 88 92 dBµ +9 +14 dBm OSC/MIX/IF Amplifier Block Item Conversion gain ∗1, ∗5 Noise figure ∗1, ∗2 1 % cross modulation ∗1, ∗3 Symbol CG1 CG2 CG3 CG4 NF1 NF2 NF3 NF4 CM1 CM2 CM3 CM4 Maximum output power Switch ON drift ∗4 Pomax ∆fsw1 ∆fsw2 ∆fsw3 ∆fsw4 Supply voltage drift ∆fst1 ∗4 ∆fst2 ∆fst3 ∆fst4 —6— ±300 kHz ±400 kHz ±400 kHz ±500 kHz ±150 kHz ±250 kHz ±200 kHz ±250 kHz CXA3205N ∗1 Measured value for untuned inputs. ∗2 Noise figure is the direct-reading value of NF meter in DSB. ∗3 Desired signal (fD) input level is –30 dBm. Undesired signal (fUD) is 100 kHz, 30 % AM at ±12 MHz. The measurement value is undesired signal level, it measured with a spectrum analyzer at S/I=46 dB. ∗4 Value when the PLL is not operating. ∗5 Loss caused by external parts connected to Pins 24 and 25 is compensated. This is the value converted to IC output pin amplitude. PLL Block Item SDA, SCL “H” level input voltage “L” level input voltage “H” level input current “L” level input current SDA “L” output voltage Clock input hysteresis Clock rate CPO (charge pump) Output current 1 Output current 2 Leak current 1 Leak current 2 REFOSC Symbol Measurement conditions VIH VIL IIH IIL LSDA CIHYS CIRATE ICPO1 ICPO2 LeakCP1 LeakCP2 FXTOSC Input capacitance CXTOSC Drive level VXTOSC BVL, BVH, BU (Band SW) Output current IBS1 Saturation voltage VSAT1 Leak current LeakBS1 FMT (Band SW) Output current IBS2 Saturation voltage VSAT2 Leak current LeakBS2 Bus timing SCL clock frequency fSCL Start waiting time tWSTA Start hold time tHSTA Low hold time tLOW High hold time tHIGH Start setup time tSSTA Data hold time tHDAT Data setup time tSDAT Rise time tR Fall time tF Stop setup time tSSTO Min. Typ. Max. Unit VCC 1.5 –0.1 –2 0.4 0.65 0.5 V V µA µA V V MHz ±75 ±300 30 100 µA µA nA µA 12 20.5 MHz pF mVp-p 100 0.5 –25 200 3 mA mV µA 75 0.03 –7 150 0.1 mA mV µA 400 kHz ns ns ns ns ns ns ns ns ns ns 3 GND VIH = VCC VIL = GND Sink current = 3 mA Byte4/Bit6 = 0 Byte4/Bit6 = 1 Byte4/Bit6 = 0 Byte4/Bit6 = 1 0 –1 0.25 0.4 ±35 ±140 ±50 ±200 3 17.5 200 Oscillator frequency range When ON When ON Sink current = 20 mA When OFF When ON When ON Sink current = 5 mA When OFF See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. See Timing Chart on Page 15. —7— 0 1300 600 1300 600 600 1300 600 19 400 300 300 600 CXA3205N Electrical Characteristics Measurement Circuit +30V 22k 8200p 1.2k 47k 0.047µ 33p +5V 47k 2SC2785 3.3µ 47k 1n 2.6ø 2.5t IF OUT LOCK 0.5p 47k 3.2ø 1.5t 1n 47k 47k 180 82p 47k 24 VCC3 REFOSC CPO CPE LOCK IFOUT1 IFOUT2 23 22 21 20 19 18 17 16 VOSC1 25 GND 26 SCL SDA ADSW FMT BVL BVH BU VCC1 MIX out1 MIX out2 GND1 BYP VHFin UHFin1 UHFin2 CXA3205N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2k 1n 4.5t 1n 1n 1n 4.5t ADSW 56p FMT 51 BVH 1T363 1T362 16p VOSC2 27 1n 1p UOSC1 28 UOSC2 29 VCC2 30 330 56p 47k 56p 1n GND2 1n SDA BVL 0.5p 1T363 8p MS 180 100p SCL 51 1:1 100 100 XTAL 4MHz 1n VCC1 0.5p 1T363 3.2ø 5.5t BVL BVH BU 100 56p 1n VHF IN 3.3µ 1n +5V —8— UHF IN 47k CXA3205N Description of Functions The CXA3205N is a ground wave broadcast tuner IC which converts frequencies to IF in order to tune and detect only the desired reception frequency of VHF, CATV and UHF band signals. In addition to the mixer, local oscillator and IF amplifier circuits required for frequency conversion to IF, this IC also integrates a PLL circuit for local oscillator frequency control onto a single chip. The functions of the various circuits are described below. 1. Mixer circuit This circuit outputs the frequency difference between the signal input to VHFIN or UHFIN and the local oscillation signal. 2. Local oscillator circuit A VCO is formed by externally connecting an LC resonance circuit composed of a varicap diode and inductance. 3. IF amplifier circuit This circuit amplifies the mixer IF output, and consists of an amplifier stage and low impedance output stage. 4. PLL circuit This PLL circuit fixes the local oscillator frequency to the desired frequency. It consists of a prescaler, main divider, reference divider, phase comparator, charge pump and reference oscillator. The control format supports the I2C bus format. The following five modes can be selected according to the combination of the frequency division values of the main and reference dividers. Mode B-0 B-1 B-2 B-3 B-4 Main divider 15 bit 14 bit 15 bit 15 bit 15 bit —9— Reference divider 1024 fixed 512 fixed 640 fixed 512 fixed 512/1024 switching CXA3205N Description of Analog Block Operation (See the Electrical Characteristics Measurement Circuit.) VHF oscillator circuit • This circuit is a differential amplifier type oscillator circuit. Pin 18 is the output and Pin 16 is the input. Oscillation is performed by connecting an LC resonance circuit including a varicap to Pin 18 via coupled capacitance, inputting to Pin 16 with feedback capacitance, and applying positive feedback. • Pin 18 is an open collector, so power must be supplied via the resonance circuit inductance or by the resistance or microinductor. The electric potential of Pin 18 at this time must be DC 3.5 V or more. • The amplifier between Pins 16 and 18 has an extremely high gain. Therefore, care should be taken to avoid creating parasitic capacitance, resistance or other feedback loops as this may produce abnormal oscillation. VHF mixer circuit • The mixer circuit employs a double balance mixer with little local oscillation signal leakage. The input format is base input type, with Pin 12 grounded and the RF signal input to Pin 13. • The RF signal is inserted from the oscillator, converted to IF frequency and output from Pins 9 and 10. • Pins 9 and 10 are open collectors, so power must be supplied externally. The electric potential of Pins 9 and 10 at this time must be DC 4.0 V or more. UHF oscillator circuit • This oscillator circuit is designed so that two collector ground type Colpitts oscillators perform differential oscillation operation via an LC resonance circuit including a varicap. An LC resonance circuit including a varicap is connected between Pins 19 and 21. • This circuit contains resonance capacitance comprising Colpitts oscillators, so the LC resonance circuit connected to Pins 19 and 21 oscillates at the frequency indicating the inductance characteristics. UHF mixer circuit • This circuit employs a double balance mixer like the VHF mixer circuit. The input format is base input type, with Pins 14 and 15 as the RF input pins. The input method can be selected from balanced input consisting of differential input to Pins 14 and 15 or unbalanced input consisting of grounding Pin 14 via a capacitor and input to Pin 15. • Pins 9 and 10 are the mixer outputs. • Pins 9 and 10 are open collectors, so power must be supplied externally. The electric potential of Pins 9 and 10 at this time must be DC 4.0 V or more. IF amplifier circuit • The signals frequency converted by the mixer are output from Pins 9 and 10, and at the same time are AC coupled inside the IC and input to the IF amplifier. • Single-tuned filters are connected to Pins 9 and 10 in order to improve the interference characteristics of the IF amplifier. • The signal amplified by the IF amplifier is balanced output from Pins 24 and 25. The output impedance is approximately 35 Ω. —10— CXA3205N Description of PLL Block The PLL on this IC supports the I2C bus control format. The control pins are as shown in the table below. Symbol ADSW SCL SDA Description Address selection SCL input SDA I/O 1) Mode Setting Method The modes for each frequency step are set according to the MS pin voltage. Mode MS pin voltage B-0 B-1 B-2 B-3 0 to 0.15 VCC OPEN 0.45 VCC to 0.55 VCC 0.65 VCC to 0.75 VCC Main divider 15 bit 14 bit 15 bit 15 bit B-4 0.85 VCC to VCC 15 bit Reference divider 1024 512 640 512 512/ 640/ 1024 Reference frequency 3.90625 kHz 7.8125 kHz 6.25 kHz 7.8125 kHz 7.8125 kHz/ 6.25 kHz/ 3.90625 kHz Frequency step∗ 31.25 kHz 62.5 kHz 50 kHz 62.5 kHz 62.5 kHz/ 50 kHz/ 31.25 kHz ∗ Frequency step is for when X’tal OSC = 4 MHz. 2) Address Setting The responding address can be changed according to the ADSW pin voltage, so that multiple PLL can exist within one system. Address ADSW pin voltage 0 to 0.1 VCC OPEN or 0.2 VCC to 0.3 VCC 0.4 VCC to 0.6 VCC 0.9 VCC to VCC MA1 0 0 1 1 MA0 0 1 0 1 —11— CXA3205N 3) Programming The VCO lock frequency is obtained according to the following formula. fosc = fref × 8 × (32 M + S) fosc : local oscillator frequency fref : reference frequency 8 : prescaler fixed frequency division ratio M : main divider frequency division ratio S : swallow counter frequency division ratio The variable frequency division ranges of M and S are as follows, and are set as binary. 32 ≤ M ≤ 1023 (32 ≤ M ≤ 511 for B-1 mode) 0 ≤ S ≤ 31 3-1) The normal control format is as follows. 3-1-1 : B-0/B-1/B-2/B-3 Modes Write-mode : Slave Receiver MODE Address byte Divider byte 1 Divider byte 2 Control byte Band SW byte MSB bit7 1 0 M2 1 X bit6 1 M9∗ M1 CP X bit5 0 M8 M0 T1 X bit4 0 M7 S4 CD X bit3 0 M6 S3 X BU bit2 MA1 M5 S2 X FMT bit1 MA0 M4 S1 X BVH LSB bit0 0 M3 S0 OS BVL A A A A A bit1 MA0 M4 S1 R0 BVH LSB bit0 0 M3 S0 OS BVL A A A A A X : Don’t care ∗ M9 is “0” for B-1 mode. 3-1-2 : B-4 Mode Write-mode : Slave Receiver MODE Address byte Divider byte 1 Divider byte 2 Control byte Band SW byte MSB bit7 1 0 M2 1 X bit6 1 M9 M1 CP X bit5 0 M8 M0 T1 X X : Don’t care —12— bit4 0 M7 S4 CD X bit3 0 M6 S3 X BU bit2 MA1 M5 S2 R1 FMT CXA3205N 3-2) The BU and FMT data order can be switched by DC grounding the BYP pin (VHF input ground side). 3-2-1 : B-0/B-1/B-2/B-3 Modes Write-mode : Slave Receiver MSB MODE bit7 Address byte 1 Divider byte 1 0 Divider byte 2 M2 Control byte 1 Band SW byte X bit6 1 M9∗ M1 CP X bit5 0 M8 M0 T1 X bit4 0 M7 S4 CD X bit3 0 M6 S3 X FMT bit2 MA1 M5 S2 X BU bit1 MA0 M4 S1 X BVH LSB bit0 0 M3 S0 OS BVL A A A A A bit1 MA0 M4 S1 R0 BVH LSB bit0 0 M3 S0 OS BVL A A A A A X : Don’t care ∗ M9 is “0” for B-1 mode. 3-2-2 : B-4 Mode Write-mode : Slave Receiver MODE Address byte Divider byte 1 Divider byte 2 Control byte Band SW byte MSB bit7 1 0 M2 1 X bit6 1 M9 M1 CP X bit5 0 M8 M0 T1 X bit4 0 M7 S4 CD X bit3 0 M6 S3 X FMT bit2 MA1 M5 S2 R1 BU X : Don’t care A MA0, MA1 M0 to S0 to T1 CD OS CP BVL BVH FMT BU R0, R1 : : : : : : : : : : : : : Acknowledge bit address setting main divider frequency division ratio setting swallow counter frequency division ratio setting test mode selection (when “1”) charge pump OFF (when “1”) varicap output OFF (when “1”) charge pump current switching (200 µA when “1”, 50 µA when “0”) VL band switch control (output PNP Tr ON when “1”) VH band switch control (output PNP Tr ON when “1”) FM trap switch control (output PNP Tr ON when “1”) UHF band switch control (output PNP Tr ON when “1”) Reference divider frequency division ratio setting —13— CXA3205N Reference Divider Frequency Division Ratio Table R1 0 1 X R0 1 1 0 Reference divider 1024 512 640 X : Don’t care 3-3) The read data format is as shown below. Read-mode : Slave Transmitter MODE Address byte Status byte A PR FL MA0, MA1 : : : : bit7 1 PR bit6 1 FL bit5 0 1 acknowledge bit power-on reset lock detection signal address setting —14— bit4 0 1 bit3 0 1 bit2 MA1 X bit1 MA0 X bit0 1 X A A CXA3205N I2C BUS Timing Chart tWSTA SDA tR tSSTA tF tSSTO SCL tHSTA START tLOW tHIGH tSDAT CLOCK tHDAT DATACHANGE tSSTA =Start setup time tWSTA =Start waiting time tHSTA =Start hold time tLOW =LOW clock pulse width tHIGH =HIGH clock pulse width tSDAT tHDAT tSSTO tR tF —15— =Data setup time =Data hold time =Stop setup time =Rise time =Fall time STOP CXA3205N Circuit current vs. Supply voltage 1 Circuit current vs. Supply voltage 2 15 UHF DICC - Circuit current [mA] AICC - Circuit current [mA] 50 VHF 45 40 4.7 4.8 4.9 5.0 5.2 5.1 5.3 10 5 5.4 4.7 4.8 VCC1 - Supply voltage [V] Band SW output voltage vs. Output current (BU, BVH, BVL) 9.2 9.0 4.9 5.0 5.1 5.2 5.3 5.4 VCC2 - Supply voltage [V] Band SW output voltage vs. Output current (FMT) 9.2 9.0 VCC3=9V VCC3=9V 8.8 Output voltage [V] Output voltage [V] 8.8 8.6 5.0 VCC3=5V 4.8 VCC3=5V 4.6 0 5 10 15 20 4.4 25 Output current [mA] I/O characteristics (Untuned input) 0 –20 fRF=350MHz (VHF) fRF=800MHz (UHF) fIF is both f=45MHz –40 –60 –60 –50 –40 –30 0 1 2 3 4 Output current [mA] 20 IF output level [dBm] 5.0 4.8 4.6 4.4 8.6 –20 –10 0 10 RF input level [dBm] —16— 5 6 CXA3205N VHF (High) VHF (Low) 20 10 0 CM - Cross modulation [dBµ] NF - Noise figure [dB] UHF 30 IFOUT 360 Ω loss of Electrical Characteristics Measurement Circuit is compensated. Measurement value : +18.3dB. 0 Noise figure vs. Reception frequency (Untuned input, in DSB) 20 fIF=45MHz 15 VHF (Low) VHF (High) 10 UHF 5 0 100 200 300 400 500 600 700 800 900 0 100 200 300 400 500 600 700 800 900 Reception frequency [MHz] Reception frequency [MHz] Next adjacent cross modulation vs. Reception frequency (Untuned input) 120 Oscillation frequency power supply fluctuation (PLL off) 400 VCC+5% VCC–5% (VCC=5V) 300 100 200 80 +B drift [kHz] CG - Conversion gain [dB] Conversion gain vs. Reception frequency (Untuned input) 40 fIF=45MHz fIF=45MHz fUD=fD+12MHz fUD=fD–12MHz (100kHz, 30% AM) 60 40 VHF (High) VHF (Low) 100 UHF 0 –100 –200 20 0 –300 0 –400 100 200 300 400 500 600 700 800 900 0 100 200 300 400 500 600 700 800 900 Reception frequency [MHz] Oscillation frequency [MHz] PCS beat characteristics +20 +10 fIF 0 IF output level [dBm] –10 –20 –30 fBeat –40 –50 –60 –70 –80 –30 IFOUT 360 Ω loss of Electrical Characteristics Measurement Circuit is compensated. Measurement value : +18.3dB. fLocal=129MHz fP=83.25MHz fC=86.83MHz, (fP–12dB) fS=87.75MHz, (fP–1.7dB) fIF=45.75MHz fBeat=fIF±920kHz –20 –10 0 +10 SG output level [dBm] (fP level) —17— +20 +30 CXA3205N Tuning Response Time VHF (Low) 95MHz → VHF (High) 395MHz T=70ms 5.0V/div offset 10.0V –90,0000ms 10,0000ms 20.0ms/div 110,000ms UHF 413MHz → UHF 847MHz T=70ms 5.0V/div offset 10.0V –90,0000ms 10,0000ms 20.0ms/div —18— 110,000ms CXA3205N IF output spectrum RL=0dBm 10dB/div VHF (Low) fRF=55MHz fLO=100MHz RF input level : –25dBm CENTER 45.0MHz RES BW 1.0kHz VBW 10Hz IF output spectrum SPAN 100.0kHz SWP 30.0s RL=0dBm 10dB/div VHF (High) fRF=350MHz fLO=395MHz RF input level : –25dBm CENTER 45.0MHz RES BW 1.0kHz VBW 10Hz —19— SPAN 100.0kHz SWP 30.0s CXA3205N IF output spectrum RL=0dBm 10dB/div UHF (Low) fRF=800MHz fLO=845MHz RF input level : –25dBm CENTER 45.0MHz RES BW 1.0kHz VBW 10Hz —20— SPAN 100.0kHz SWP 30.0s CXA3205N VHF Input Impedance j50 j25 VHFin 50MHz 50 BYP 0 j100 12 13 1000p S11 350MHz –j25 –j100 –j50 UHF Input Impedance j50 UHFin2 0 j100 UHFin1 j25 14 15 50 1000p S11 350MHz 800MHz –j25 –j100 –j50 —21— CXA3205N IF Output Impedance j50 j25 0 j100 50 –j25 45MHz –j100 –j50 —22— CXA3205N Package Outline Unit : mm 30PIN SSOP (PLASTIC) + 0.2 1.25 – 0.1 ∗9.7 ± 0.1 1 + 0.1 0.22 – 0.05 7.6 ± 0.2 16 ∗5.6 ± 0.1 30 0.10 A 15 + 0.05 0.15 – 0.02 0.65 0.13 M 0.5 ± 0.2 0.1 ± 0.1 0° to 10° NOTE: Dimension “∗” does not include mold protrusion. DETAIL A PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE SSOP-30P-L01 LEAD TREATMENT SOLDER/PALLADIUM PLATING EIAJ CODE SSOP030-P-0056 LEAD MATERIAL 42/COPPER ALLOY PACKAGE MASS 0.1g JEDEC CODE NOTE : PALLADIUM PLATING This product uses S-PdPPF (Sony Spec.-Palladium Pre-Plated Lead Frame). —23—