ULTRA MINIATURE RELAY SIGNAL RELAY FTR-C2 Series RoHS compliant n Features Dimensions of large contact gap relay Height:11.8 mm maximum (THT) 12 mm maximum (SMT) Length: 20.2 mm maximum Width:10 mm maximum lConforms to IEC60950 / EN60950 / UL1950/ CSA C22.2 No.950 spacing & high breakdown voltage l Recognized by UL/CSA and Bsi UL: File E63615 Vol. 2 Sec.4 CSA: Master contract 169663 Certificate 1088921 Clearance: 2.0 mm (between open contacts, coil and contacts, contact sets) Creepage: 2.0 mm (between open contacts, coil and contacts, contact sets) l HIGH RELIABILITY Bifurcated contacts lLow power consumption 300 mV lRoHS Compliant since production l n ORDERING INFORMATION [Example] FTR-C2 C A 012 G -B 05* (a) ( b)(c) (d) (e) (f) (g) (a) Series Name FTR-C2 (b) Termianl Apprearance C: Through hole type G: Surface mount type (c) Operation Function A: Standard type B: Latching type (d) Coil Number Nominal Voltage (e) Contact Material G: Silver alloy (f) Relay enclosing direction B: standard enclosing direction (g) Number of relays per reel 05: 500 (standard) Remarks: Actual marking on relay would not carry code FTR and be as below: Ordering code Actual marking FTR-C2CA03G → C2CA03G *only SMT version FTR-C2 Series n COIL DATA CHART Standard type Nominal Voltage Coil Resistance (±10%) Must Operate Voltage Must Release Voltage Nominal Operating Power (±10%) FTR-C2 ( ) A003G 3 VDC 30.0 Ω 2.25 VDC 0.3 VDC 300 mW FTR-C2 ( ) A005G 5 VDC 83.3 Ω 3.75 VDC 0.5 VDC 300 mW FTR-C2 ( ) A012G 12VDC 480.0 Ω 9.00 VDC 1.2 VDC 300 mW FTR-C2 ( ) A024G 24 VDC 1,920.0 Ω 18.00 VDC 2.4 VDC 300 mW Nominal Voltage Coil Resistance (±10%) Set Voltage Reset Voltage Nominal Operating Power (±10%) Model Single coil latching type Model Ω FTR-C2 ( ) B003G 3 VDC 60.0 Ω 2.25 VDC 2.25 VDC 150 mW FTR-C2 ( ) B005G 5 VDC 167.0 Ω 3.75 VDC 3.75 VDC 150 mW FTR-C2 ( ) B0012G 12VDC 960.0 Ω 9.00 VDC 9.00 VDC 150 mW FTR-C2 ( ) B024G 24 VDC 3,840.0 Ω 18.00 VDC 18.00 VDC 150 mW Note: All values in the table are measured at 20˚C. FTR-C2 Series n SPECIFICATIONS FTR-C2CA ( )G FTR-C2GA-( )G Item Contact Coil Time Value Arrangement 2 F o rm C Material Silver alloy Resistance (initial) Max. 150m ohm (at 1A 6VDC) Max. Switching Power 37.5AV / 30W Max. Switching Voltage 250VAC, 220 VDC Max. Switching Current 1A Operating Temperature -40˚ C to + 85˚ C (no frost) Max. Allowable Voltage 150% nominal voltage (at 20˚ C) Operate Time Max. 15ms (at nominal voltage, without bounce Release Time (without diode) Max. 15ms (at nominal voltage, without bounce Resistance (at 500 VDC) Min. 1,000M ohm Dieelectric Strenght Insulation Surge Strength Between open contacts 1,500VAC, 1 minute Between adjacent contacts 1,500VAC, 1 minute Between coil and contacts 2,000VAC, 1 minute Between open contacts 2,500V (at10/700micros) Between adjacent contacts 2,500V (at10/700micros) Between coil and contacts 2,500V (at10/700micros) Mechanical 10x106 operations min. (at 10Hz) Electrical (resistive load) 100x103 operations min. at 1A, 30VDC, 0.5Hz 100x103 operations min. at 0.1A, 48VDC, 0.5Hz 100x103 operations min. at 0.3A, 125VDC, 0.5Hz Vibration Resistance Misoperation 10 to 55 Hz at double amplitude of 3.3 mm Endurance 10 to 55 Hz at double amplitude of 5 mm Shock Resistance Misoperation Min. 300 m/s2 Endurance Min. 1,000 m/s2 UL / CSA Contact Rating 0.3A 125 VAC 1A 30VDC 0.3 110VDC Insulation Class Supplementary Insulation Working Voltage 250 V Pollution Degree 2 (outside) 1 (inside) Clearance 2.0 mm (outside) 2.0 mm (inside) Creepage Distance 2.5 mm (outside) 2.0 mm (inside) Life IEC060950 UL1950 C22.2 No.950 EN60950 FTR-C2 Series n DIMENSIONS AND SCHEMATICS 3.5 11.4 ±0.3 Through hole type (1.135) 5.08 ±0.3 n (1.115) 7.62 ±0.3 TERMINAL DESIGNATIONS 7.62 ±0.3 5.08 ±0.3 n Unit: mm RECOMMENDED MOUNTING PAD 7.62 ±0.1 (1.115) (Bottom view de-energized position) 8-O 0.9±0.1 (1.135) bar Single Coil Polarity Latching Type 7.62 ±0.1 5.08 ±0.1 5.08 ±0.1 (Bottom view reset position) S R Polarity bar S: shows polarity of set position R: shows polarity of reset position Unit: mm FTR-C2 Series n DIMENSIONS AND SCHEMATICS 7.62 ±0.3 5.08 ±0.3 7.62 ±0.3 5.08 ±0.3 11.7 ±0.3 0.3+0 -0.1 3 o ±.2 o (1.135) 1.5 0.25+.03 Surface mount type 10.8 ±0.3 n TERMINAL DESIGNATIONS n Unit: mm RECOMMENDED MOUNTING 1 ±0.1 1 ±0.1 1 ±0.1 1 ±0.1 Polarity bar Single Coil Latching Type 3±0.1 8.9±0.1 3±0.1 (Top view de-energized position) 7.62 ±0.1 5.08 ±0.1 5.08 ±0.1 (Top view reset position) S R Polarity bar S: shows polarity of set position R: shows polarity of reset position Unit: mm FTR-C2 Series n RECOMMENDED SOLDERING CONDITIONS (TEMPERATURE PROFILE) Temperature (C) IRS (Infrared Reflow Soldering) soldering T3 T 3 = 245C max. T 2 = 200C max. cooling T 1 = 165C max. T2 T1 0 preheating 120 sec maximum Note: 1.Temperature profiles show the tempera- ture of PC board surface. 2. Please perform soldering test with your actual PC board before mass produc- tion, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. 30 sec Max. FTR-C2 Series RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu amd Sm-3.0 Cu-Ni (only FTR-B3 and FTR-B4 from February 2005. Reflow Solder condtion for SMT Peak Temp.: max. 250C Soldering Temperature ( C) 250 Flow Solder condtion: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: 220 Cooling Pre-heating 0 Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. 30 90~20 sec. max. 20 sec. 20~30 sec. (duration) We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical realys. l 4. Tin Whisker SnAgCu and SnCuNi solder is known as low risk of tin whisker. No considerable length whisker was found by our in-house test. l FTR-C2 Series Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: http://www.fujitsu.com/emea/services/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://www.fujitsu.com/us/services/edevices/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2005 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property off their respective owners. Fujitsu Components America does not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. reserves the right to change specifications/datasheets without prior notice. Rev. 11/18/2005.