POWER RELAY 1 POLE—5 A (CADMIUM FREE CONTACTS TYPE) NY SERIES RoHS compliant ■ FEATURES Ultra slim type with 5 mm thickness —Good for high density mounting ● Low power consumption and high sensitivity —Nominal coil power: 120 mW —Operating power: 54 mW ● UL, CSA, VDE recognized ● Conforms to IEC 1010-1 and 1131-2 ● Wide operating range ● SIL pitch terminals ● Plastic sealed type ● Compatible with solid state I/O module type SN (see page 376) in size and pin (terminal) arrangement ● Environmentally friendly cadmium free contact type is available. ● RoHS compliant since date code: 0439C1 Please see page 6 for more information ● ■ ORDERING INFORMATION [Example] NY P – 12 (a) (b) (*) (c) W – K (d) (e) (a) Series Name NY: NY Series (b) Terminal Classification Nil : PC board mounting type P : Socket mounting type (c) Nominal Voltage Refer to the COIL DATA CHART (d) Contact W : Bifurcated type (e) Enclosure K : Plastic sealed type Note: Actual marking omits the hyphen (-) of (*) ■ SAFETY STANDARD AND FILE NUMBERS UL508 (File No. E56140) C22.2 No. 14 (File No. LR35579) VDE0435 (File No. 11039-4940-1013) Please note that UL/CSA ratings may differ from the standard ratings. Nominal voltage 4.5 to 24 VDC Contact rating 1/8 HP 125 VAC/250 VAC 5 A 30 VDC/250 VAC resistive Pilot duty C 300 1 NY SERIES ■ SPECIFICATIONS Item Contact NY Arrangement 1 form A (SPST-NO) Material Gold overlay silver alloy Style Bifurcated Resistance (initial) Maximum 30 mΩ (at 1 A 6 VDC) Rating (resistive) 3 A 250 VAC or 3 A 30 VDC Maximum Carrying Current 5A Maximum Switching Power 750 VA, 90 W Maximum Switching Voltage 270 VAC, 125 VDC Maximum Switching Current 5A Minimum Switching Coil Time Value Insulation Life Other Load*1 1mA 5 VDC Nominal Power (at 20°C) 0.12W Operate Power (at 20°C) 0.054 W Operating Temperature –40°C to +90°C (no frost) (refer to the CHARACTERISTIC DATA) Operate (at nominal voltage) Maximum 10 ms Release (at nominal voltage) Maximum 5 ms Resistance (at 500 VDC) Minimum 1,000 MΩ between open contacts Dielectric Strength between coil and contacts 750 VAC 1 minute Surge Strength 5,080 V (at 1.2 × 50 µs) Mechanical 2 x 10 7 operations minimum Electrical 1.5 × 10 5 operations minimum (at 5A 30VDC) 1.5 × 10 5 operations minimum (at 3 A 120 VAC) 3 × 10 4 operations minimum (at 5 A 250 VAC) Vibration Resistance Shock Resistance Weight 3,000 VAC 1 minute Misoperation 10 to 55 Hz (double amplitude of 1.5 mm) Endurance 10 to 55 Hz (double amplitude of 5.0 mm) Misoperation 100 m/s2 (11 ± 1 ms) Endurance 1,000 m/s2 (6 ± 1 ms) Approximately 3.5 g *1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 NY SERIES ■ COIL DATA CHART MODEL Nominal voltage Coil resistance (±10%) Must operate voltage NY- 4.5 W-K 4.5 VDC 169 Ω 3 Must release voltage Nominal power VDC 0.45 VDC 120 mW NY- 5 W-K 5 VDC 208 Ω 3.35 VDC 0.5 VDC 120 mW NY- 6 W-K 6 VDC 300 Ω 4 VDC 0.6 VDC 120 mW NY- 9 W-K 9 VDC 675 Ω 6 VDC 0.9 VDC 120 mW NY- 12 W-K 12 VDC 1,200 Ω 8 VDC 1.2 VDC 120 mW NY- 18 W-K 18 VDC 2,700 Ω 12.1 VDC 1.8 VDC 120 mW NY- 24 W-K 24 VDC 4,800 Ω 16.1 VDC 2.4 VDC 120 mW Note: All values in the table are measured at 20°C ■ CHARACTERISTIC DATA Switching Current (A) Maximum Switching Power AC Resistive Load 5 3 2 DC Resistive Load 1 0.5 0.3 0.2 0.1 10 20 30 50 100 200 300 500 Switching Voltage (V) 3 NY SERIES ■ REFERENCE DATA ■ DIMENSIONS ● Dimensions ● Schematics (BOTTOM VIEW) NY type +0.08 ● PC board mounting hole layout (BOTTOM VIEW) 17.5 20.1 0.98 NYP type +0.08 17.5+0.2 20.1 0.98 Unit: mm 4 NY SERIES ■ SOCKET DRILLING PLANT 24.5 ■ SOCKET DIMENSIONS Unit: mm ■ NOTES 1. Socket ordering code. JL-5N 2. Standard IC socket is not recommended. Please use socket JL-5N. 5 NY SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fcai.fujitsu.com/pdf/LeadFreeLetter.pdf) ● Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. From February 2005 forward Sn-3.0Cu-Ni will be used for FTRB3 and FTR-B4 series relays. ● Most signal and some power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 6 hazardous materials that are restricted by RoHS directive (lead, mercury, cadmium, chromium IV, PBB, PBDE). ● It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). ● “LF” is marked on each outer and inner carton. (No marking on individual relays). ● To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. We will ship leaded relays as long as the leaded relay inventory exists. ● 2. Recommended Lead Free Solder Profile ● Recommended solder paste Sn-3.0Ag-0.5Cu and Sn-3.0 Cu-Ni (only FTR-B3 and FTR-B4 from February 2005) Reflow Solder condtion Flow Solder condtion: Peak Temp.: max. 250˚C Soldering temperature (˚C) 250 Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: 220 Cooling Pre-heating 170 Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. 130 90~120 sec. max. 120 sec. 20~30 sec. (duration) We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity ● Moisture Sensitivity Level standard is not applicable to electromechanical realys. 4. Tin Whisker ● SnAgCu solder is known as low riskof tin whisker. No considerable length whisker was found by our in-house test. 5. Solid State Relays Each lead terminal will be changed from solder plating to Sn plating and Nickel plating. A layer of Nickel plating is between the terminal and the Sn plating to avoid whisker. 6 ● NY SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] www.fcal.fujitsu.com © 2005 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 07/19/2005.. 7