HA-5002/883 TM Monolithic, Wideband, High Slew Rate, High Output Current Buffer July 1994 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The HA-5002/883 is a monolithic, wideband, high slew rate, high output current, buffer amplifier. Utilizing the advantages of the Harris Dielectric Isolation technologies, the HA-5002/883 current buffer offers 1300V/µs slew rate typically and 1000V/µs minimum with 110MHz of bandwidth. The ±100mA minimum output current capability is enhanced by a 3Ω output impedance. • Voltage Gain (RL = 1kΩ) . . . . . . . . . . . . . . . . . 0.98 (Min) 0.995 (Typ) (RL = 100Ω) . . . . . . . . . . . . . . . . 0.96 (Min) 0.971 (Typ) The monolithic HA-5002/883 will replace the hybrid LH0002 with corresponding performance increases. These characteristics range from the 3MΩ (typ) input impedance to the increased output voltage swing. Monolithic design technologies have allowed a more precise buffer to be developed with more than an order of magnitude smaller gain error. The voltage gain is 0.98 guaranteed minimum with a 1kΩ load and 0.96 minimum with a 100Ω load. • High Input Impedance . . . . . . . . . . . . . . . . . 1.5MΩ (Min) 3MΩ (Typ) • Low Output Impedance . . . . . . . . . . . . . . . . . . 5Ω (Max) 3Ω (Typ) • Very High Slew Rate . . . . . . . . . . . . . . . .1000V/µs (Min) 1300V/µs (Typ) • Wide Small Signal Bandwidth. . . . . . . . . 110MHz (Typ) The HA-5002/883 will provide many present hybrid users with a higher degree of reliability and at the same time increase overall circuit performance. • High Output Current . . . . . . . . . . . . . . . . . 100mA (Min) • High Pulsed Output Current . . . . . . . . . . . 400mA (Max) • Monolithic Dielectric Isolation Construction Ordering Information • Replaces Hybrid LH0002 Applications PART NUMBER • Line Driver TEMPERATURE RANGE PACKAGE • Data Acquisition HA2-5002/883 -55oC to +125oC 8 Pin Can • 110MHz Buffer HA4-5002/883 -55oC to +125oC 20 Lead Ceramic LCC HA7-5002/883 -55oC to +125oC 8 Lead CerDIP • High Power Current Booster • High Power Current Source • Sample and Holds • Radar Cable Driver • Video Products Pinouts IN NC 2 NC 3 OUT 8 OUT V1 + 1 NC V1 + HA-5002/883 (METAL CAN) TOP VIEW HA-5002/883 (CLCC) TOP VIEW HA-5002/883 (CERDIP) TOP VIEW 8 1 20 19 V2 - 2 7 V2 + NC 4 18 NC NC 3 6 NC V2 - 5 17 V2 + NC 6 16 NC NC 7 15 NC NC 8 14 NC IN 4 5 V1 - NC V1 - IN NC NC 9 10 11 12 13 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 258 V1+ 1 7 V2 + 2 NC V 1- 6 5 3 V2 - NC 4 OUT Spec Number 511017-883 FN3705 Specifications HA-5002/883 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 44V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equal to Supplies Peak Output Current (50ms On, 1s Off) . . . . . . . . . . . . . . . . . .±400mA Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <4000V Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W Metal Can Package . . . . . . . . . . . . . . . . . 155oC/W 67oC/W Package Power Dissipation Limit at +75oC for TJ ≤ +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . ±12V to ±15V RL ≥ 100Ω TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: V SUPPLY = ±12V and ±15V, RSOURCE = 50Ω, C LOAD ≤ 10pF, VIN = 0V, Unless Otherwise Specified. PARAMETERS Input Offset Voltage SYMBOL VIO1 CONDITIONS VSUP = ±15V TEMPERATURE MIN MAX UNITS 1 +25oC -20 20 mV -30 30 mV -20 20 mV -30 30 mV -7 7 µA -10 10 µA -7 7 µA -10 10 µA 0.98 - V/V 0.98 - V/V 0.98 - V/V 0.98 - V/V 2, 3 VIO2 VSUP = ±12V 1 2, 3 Input Bias Current IB1 VSUP = ±15V, R S = 1kΩ 1 2, 3 IB2 VSUP = ±12V, R S = 1kΩ 1 2, 3 Voltage Gain 1 +AV1 -AV1 Voltage Gain 2 Voltage Gain 3 VSUP = ±12V, R L = 1kΩ, V IN = 10V VSUP = ±12V, R L = 1kΩ, V IN = -10V LIMITS GROUP A SUBGROUPS 1 2, 3 1 2, 3 +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +AV2 VSUP = ±12V, R L = 100Ω, VIN = 10V 1 +25oC 0.96 - V/V -AV2 VSUP = ±12V, R L = 100Ω, VIN = -10V 1 +25oC 0.96 - V/V +AV3 VSUP = ±15V, R L = 100Ω, VIN = 10V 1 +25oC 0.96 - V/V -AV3 VSUP = ±15V, R L = 100Ω, VIN = -10V 1 +25oC 0.96 - V/V Spec Number 259 511017-883 Specifications HA-5002/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: V SUPPLY = ±12V and ±15V, RSOURCE = 50Ω, C LOAD ≤ 10pF, VIN = 0V, Unless Otherwise Specified. PARAMETERS Voltage Gain 4 SYMBOL +AV4 -AV4 Output Voltage Swing +VOUT1 -VOUT1 +VOUT2 -VOUT2 +VOUT3 -VOUT3 Output Current +IOUT1 -IOUT1 +IOUT2 -IOUT2 Power Supply Rejection Ratio +PSRR1 -PSRR1 +PSRR2 -PSRR2 CONDITIONS VSUP = ±15V, RL = 1kΩ, VIN = +10V VSUP = ±15V, RL = 1kΩ, VIN = -10V VSUP = ±15V, RL = 100Ω, VIN = +15V VSUP = ±15V, RL = 100Ω, VIN = -15V VSUP = ±15V, RL = 1kΩ, VIN = +15V VSUP = ±15V, RL = 1kΩ, VIN = -15V VSUP = ±12V, RL = 1kΩ, VIN = +12V VSUP = ±12V, RL = 1kΩ, VIN = -12V VSUP = ±15V, VOUT = +10V VSUP = ±15V, VOUT = -10V VSUP = ±12V, VOUT = +10V VSUP = ±12V, VOUT = -10V ∆VSUP = ±5V, V+ = +20V, V- = -15V, V+ = +10V, V- = -15V ∆VSUP = ±5V, V+ = +15V, V- = -20V, V+ = +15V, V- = -10V ∆VSUP = ±5V, V+ = +17V, V- = -12V, V+ = +7V, V- = -12V ∆VSUP = ±5V, V+ = +12V, V- = -17V, V+ = +12V, V- = -7V LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC 0.99 - V/V 0.99 - V/V 2, 3 +125oC, -55oC 1 +25oC 0.99 - V/V 2, 3 +125oC, -55oC 0.99 - V/V 1 +25oC 10 - V o o 2, 3 +125 C, -55 C 10 - V 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 10 - V 10 - V 2, 3 +125oC, -55oC 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 10 - V 10 - V 2, 3 +125oC, -55oC 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 100 - mA o o 2, 3 +125 C, -55 C 100 - mA 1 +25oC - -100 mA o o 2, 3 +125 C, -55 C - -100 mA 1 +25oC 100 - mA o o 2, 3 +125 C, -55 C 100 - mA 1 +25oC - -100 mA o o 2, 3 +125 C, -55 C - -100 mA 1 +25oC 54 - dB o o 2, 3 +125 C, -55 C 54 - dB 1 +25oC 54 - dB 2, 3 +125oC, -55oC 54 - dB 1 +25oC 54 - dB 54 - dB 2, 3 +125oC, -55oC 1 +25oC 54 - dB 2, 3 +125oC, -55oC 54 - dB Spec Number 260 511017-883 Specifications HA-5002/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: V SUPPLY = ±12V and ±15V, RSOURCE = 50Ω, C LOAD ≤ 10pF, VIN = 0V, Unless Otherwise Specified. PARAMETERS SYMBOL Power Supply Current +ICC 1 -ICC 1 +ICC 2 -ICC 2 CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC - 10 mA - 10 mA -10 - mA -10 - mA - 10 mA - 10 mA -10 - mA -10 - mA VSUP = ±15V, VOUT = 0V +125oC, 2, 3 VSUP = ±15V, VOUT = 0V +25oC 1 +125oC, 2, 3 VSUP = ±12V, VOUT = 0V -55oC +25oC 1 +125oC, 2, 3 VSUP = ±12V, VOUT = 0V -55oC -55oC +25oC 1 +125oC, 2, 3 -55oC TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Table 2 Intentionally Left Blank. See AC Specifications in Table 3 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V or ±12V, RLOAD = 1kΩ, CLOAD ≤ 10pF, Unless Otherwise Specified. LIMITS PARAMETERS Input Resistance Slew Rate SYMBOL NOTES TEMPERATURE MIN MAX UNITS RIN1 VSUP = ±15V 1 +25oC 1.5 - MΩ RIN2 VSUP = ±12V 1 +25oC 1.5 - MΩ +SR1 VSUP = ±15V, VOUT = -5V to +5V 1 +25oC 1000 - V/µs +125oC, -55oC 1000 - V/µs VSUP = ±15V, VOUT = +5V to -5V 1 +25oC 1000 - V/µs +125oC, -55oC 1000 - V/µs VSUP = ±12V, VOUT = -5V to +5V 1 +25oC 1000 - V/µs +125oC, -55oC 1000 - V/µs VSUP = ±12V, VOUT = +5V to -5V 1 +25oC 1000 - V/µs +125oC, -55oC 1000 - V/µs -SR1 +SR2 -SR2 Rise and Fall Time CONDITIONS TR TF VSUP = ±15V or ±12V, VOUT = 0 to +500mV 1, 2 +25oC - 10 ns 1, 2 +125oC, -55oC - 10 ns VSUP = ±15V or ±12V, VOUT = 0 to -500mV 1, 2 +25oC - 10 ns 1, 2 +125oC, -55oC - 10 ns Spec Number 261 511017-883 Specifications HA-5002/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Characterized at: VSUPPLY = ±15V or ±12V, RLOAD = 1kΩ, CLOAD ≤ 10pF, Unless Otherwise Specified. LIMITS PARAMETERS Overshoot SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS +OS VSUP = ±12V or ±15V, VOUT = 0 to +500mV 1 +25oC - 30 % +125oC, -55oC - 30 % VSUP = ±12V or ±15V, VOUT = 0 to -500mV 1 +25oC - 30 % +125oC, -55oC - 30 % +25oC - 300 mW +125oC, -55oC - 300 mW +25oC - 240 mW +125oC, -55oC - 240 mW -OS Quiescent Power Consumption VSUP = ±15V, VIN = 0V, IOUT = 0mA 1, 3 VSUP = ±12V, VIN = 0V, IOUT = 0mA 1, 3 ROUT1 VSUP = ±12V 1 +25oC - 5 Ω ROUT2 VSUP = ±12V 1 +25oC - 5 Ω PC1 PC2 Output Resistance NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Measured between 10% and 90% points. 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.) TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLE 1) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3 Group A Test Requirements 1, 2, 3 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 262 511017-883 HA-5002/883 Die Characteristics DIE DIMENSIONS: 81 x 80 x 19 mils ± 1 mils 2050 x 2030 x 483µm ± 25.4µm METALLIZATION: Type: Al, 1% Cu Thickness: 20kÅ ± 2kÅ GLASSIVATION: Type: Nitride Thickness: 7kÅ ± 0.7kÅ WORST CASE CURRENT DENSITY: 0.7 x 105 A/cm2 at 3.6mA SUBSTRATE POTENTIAL (Powered Up): V1TRANSISTOR COUNT: 27 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA-5002/883 V1- IN V1- (ALT) V1+ (ALT) V2+ V 2- V 1+ OUT All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Spec Number 263 511017-883