INTERSIL HA5023IB

HA5023
®
Data Sheet
June 2, 2006
Dual 125MHz Video Current
Feedback Amplifier
FN3393.8
Features
• Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz
The HA5023 is a wide bandwidth high slew rate dual
amplifier optimized for video applications and gains between
1 and 10. It is a current feedback amplifier and thus yields
less bandwidth degradation at high closed loop gains than
voltage feedback amplifiers.
The low differential gain and phase, 0.1dB gain flatness, and
ability to drive two back terminated 75Ω cables, make this
amplifier ideal for demanding video applications.
The current feedback design allows the user to take
advantage of the amplifier’s bandwidth dependency on the
feedback resistor. By reducing RF, the bandwidth can be
increased to compensate for decreases at higher closed
loop gains or heavy output loads.
The performance of the HA5023 is very similar to the
popular Intersil HA-5020.
• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs
• Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . 800µV
• Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03%
• Differential Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03°
• Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA
• ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V
• Guaranteed Specifications at ±5V Supplies
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• Video Gain Block
• Video Distribution Amplifier/RGB Amplifier
• Flash A/D Driver
Ordering Information
PART
NUMBER
PART
TEMP.
MARKING RANGE (°C)
• Current to Voltage Converter
PACKAGE
PKG.
DWG. #
• Medical Imaging
HA5023IP
HA5023IP
-40 to 85
8 Ld PDIP
E8.3
• Radar and Imaging Systems
HA5023IPZ
(Note)
HA5023IPZ
-40 to 85
8 Ld PDIP*
(Pb-free)
E8.3
• Video Switching and Routing
HA5023IB
5023I
-40 to 85
8 Ld SOIC
M8.15
HA5023IB96
5023I
-40 to 85
8 Ld SOIC
M8.15
Tape and Reel
HA5023IBZ
(Note)
5023IBZ
-40 to 85
8 Ld SOIC
(Pb-free)
HA5023IBZ96 5023IBZ
(Note)
HA5023EVAL
-40 to 85
Pinout
HA5023
(PDIP, SOIC)
TOP VIEW
M8.15
M8.15
8 Ld SOIC
Tape and Reel
(Pb-free)
High Speed Op Amp DIP Evaluation Board
OUT1
1
-IN1
2
+IN1
3
V-
4
-+
+-
8
V+
7
OUT2
6
-IN2
5
+IN2
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1998, 2005-2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
HA5023
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . .36V
DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V
Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected
ESD Rating (Note 3)
Human Body Model (Per MIL-STD-883 Method 3015.7). . . 2000V
Thermal Resistance (Typical, Note 2)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . ±4.5V to ±15V
θJA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
160
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Package, Note 1) . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175°C for die, and below 150°C
for plastic packages. See Application Information section for safe operating area information.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
3. The non-inverting input of unused amplifiers must be connected to GND.
4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)
output current should not exceed 15mA for maximum reliability.
Electrical Specifications
VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
A
25
-
0.8
3
mV
A
Full
-
-
5
mV
Delta VIO Between Channels
A
Full
-
1.2
3.5
mV
Average Input Offset Voltage Drift
B
Full
-
5
-
µV/°C
A
25
53
-
-
dB
A
Full
50
-
-
dB
A
25
60
-
-
dB
A
Full
55
-
-
dB
A
Full
±2.5
-
-
V
A
25
-
3
8
µA
A
Full
-
-
20
µA
A
25
-
-
0.15
µA/V
A
Full
-
-
0.5
µA/V
A
25
-
-
0.1
µA/V
A
Full
-
-
0.3
µA/V
A
25, 85
-
4
12
µA
A
-40
-
10
30
µA
A
25, 85
-
6
15
µA
A
-40
-
10
30
µA
PARAMETER
TEST CONDITIONS
INPUT CHARACTERISTICS
Input Offset Voltage (VIO)
VIO Common Mode Rejection Ratio
VIO Power Supply Rejection Ratio
Input Common Mode Range
Note 5
±3.5V ≤ VS ≤ ±6.5V
Note 5
Non-Inverting Input (+IN) Current
+IN Common Mode Rejection
Note 5
(+IBCMR = 1 )
+RIN
±3.5V ≤ VS ≤ ±6.5V
+IN Power Supply Rejection
Inverting Input (-IN) Current
Delta -IN BIAS Current Between Channels
2
FN3393.8
June 2, 2006
HA5023
Electrical Specifications
VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
-IN Common Mode Rejection
Note 5
±3.5V ≤ VS ≤ ±6.5V
-IN Power Supply Rejection
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
A
25
-
-
0.4
µA/V
A
Full
-
-
1.0
µA/V
A
25
-
-
0.2
µA/V
A
Full
-
-
0.5
µA/V
Input Noise Voltage
f = 1kHz
B
25
-
4.5
-
nV/√Hz
+Input Noise Current
f = 1kHz
B
25
-
2.5
-
pA/√Hz
-Input Noise Current
f = 1kHz
B
25
-
25.0
-
pA/√Hz
Note 11
A
25
1.0
-
-
MΩ
A
Full
0.85
-
-
MΩ
A
25
70
-
-
dB
A
Full
65
-
-
dB
A
25
50
-
-
dB
A
Full
45
-
-
dB
A
25
±2.5
±3.0
-
V
A
Full
±2.5
±3.0
-
V
TRANSFER CHARACTERISTICS
Transimpedence
RL = 400Ω, VOUT = ±2.5V
Open Loop DC Voltage Gain
RL = 100Ω, VOUT = ±2.5V
Open Loop DC Voltage Gain
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 150Ω
Output Current
RL = 150Ω
B
Full
±16.6
±20.0
-
mA
Output Current, Short Circuit
VIN = ±2.5V, VOUT = 0V
A
Full
±40
±60
-
mA
Supply Voltage Range
A
25
5
-
15
V
Quiescent Supply Current
A
Full
-
7.5
10
mA/Op Amp
POWER SUPPLY CHARACTERISTICS
AC CHARACTERISTICS (AV = +1)
Slew Rate
Note 6
B
25
275
350
-
V/µs
Full Power Bandwidth
Note 7
B
25
22
28
-
MHz
Rise Time
Note 8
B
25
-
6
-
ns
Fall Time
Note 8
B
25
-
6
-
ns
Propagation Delay
Note 8
B
25
-
6
-
ns
B
25
-
4.5
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
125
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
50
-
ns
Settling Time to 0.25%
2V Output Step
B
25
-
75
-
ns
3
FN3393.8
June 2, 2006
HA5023
Electrical Specifications
VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
(NOTE 9)
TEST
LEVEL
TEMP.
(°C)
MIN
TYP
MAX
UNITS
AC CHARACTERISTICS (AV = +2, RF = 681Ω)
Slew Rate
Note 6
B
25
-
475
-
V/µs
Full Power Bandwidth
Note 7
B
25
-
26
-
MHz
Rise Time
Note 8
B
25
-
6
-
ns
Fall Time
Note 8
B
25
-
6
-
ns
Propagation Delay
Note 8
B
25
-
6
-
ns
B
25
-
12
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
95
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
50
-
ns
Settling Time to 0.25%
2V Output Step
B
25
-
100
-
ns
Gain Flatness
5MHz
B
25
-
0.02
-
dB
20MHz
B
25
-
0.07
-
dB
AC CHARACTERISTICS (AV = +10, RF = 383Ω)
Slew Rate
Note 6
B
25
350
475
-
V/µs
Full Power Bandwidth
Note 7
B
25
28
38
-
MHz
Rise Time
Note 8
B
25
-
8
-
ns
Fall Time
Note 8
B
25
-
9
-
ns
Propagation Delay
Note 8
B
25
-
9
-
ns
B
25
-
1.8
-
%
Overshoot
-3dB Bandwidth
VOUT = 100mV
B
25
-
65
-
MHz
Settling Time to 1%
2V Output Step
B
25
-
75
-
ns
Settling Time to 0.1%
2V Output Step
B
25
-
130
-
ns
Differential Gain (Note 10)
RL = 150Ω
B
25
-
0.03
-
%
Differential Phase (Note 10)
RL = 150Ω
B
25
-
0.03
-
°
VIDEO CHARACTERISTICS
NOTES:
5. VCM = ±2.5V. At -40°C Product is tested at VCM = ±2.25V because Short Test Duration does not allow self heating.
6. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
Slew Rate
7. FPBW = ----------------------------- ; V
= 2V .
2πV PEAK PEAK
8. RL = 100Ω, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
9. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.
10. Measured with a VM700A video tester using an NTC-7 composite VITS.
11. VOUT = ±2.5V. At -40°C Product is tested at VOUT = ±2.25V because Short Test Duration does not allow self heating.
4
FN3393.8
June 2, 2006
HA5023
Test Circuits and Waveforms
+
DUT
50Ω
HP4195
NETWORK
ANALYZER
50Ω
FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS
(NOTE 12)
100Ω
(NOTE 12)
100Ω
VIN
+
VIN
DUT
VOUT
-
50Ω
RL
100Ω
+
DUT
VOUT
-
50Ω
RI
681Ω
RF, 681Ω
RL
400Ω
RF, 1kΩ
FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT
FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT
NOTE:
12. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5023 is powered up.
Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div.
Horizontal Scale: 20ns/Div.
FIGURE 4. SMALL SIGNAL RESPONSE
5
Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div.
Horizontal Scale: 50ns/Div.
FIGURE 5. LARGE SIGNAL RESPONSE
FN3393.8
June 2, 2006
Schematic Diagram
(One Amplifier of Two)
V+
R2
800
R5
2.5K
R10
820
QP8
R15
400
QP9
R19
400
QP11
QP1
QP5
QP14
R11
1K
R17
280
QN5
6
QP15
QN12
R24
140
QP16
QP20
R20
140
C1
1.4pF
QN8
QP2
QP12
R28
20
QP6
R1
60K
QN6
QN1
-IN
R12
280
QP4
QP17
QN13
+IN
QN17
C2
1.4pF
QN2
QN4
QN3
R14
280
R13
1K
QN7
R25
20
QN15
R21
140
QN10
QP7
HA5023
QP13
R3
6K
D1
QP19
R31
5
R18
280
QP10
R29
9.5
R27
200
R22
280
QN21
R25
140
QN18
QN14
QN16
R16
400
R23
400
R26
200
R32
5
QN19
R30
7
OUT
R4
800
V-
R33
800
R9
820
QN9
QN11
FN3393.8
June 2, 2006
HA5023
Application Information
traces connected to -IN, and that connections to -IN be kept
as short as possible to minimize the capacitance from this
node to ground.
Optimum Feedback Resistor
The plots of inverting and non-inverting frequency response,
see Figure 8 and Figure 9 in the typical performance section,
illustrate the performance of the HA5023 in various closed
loop gain configurations. Although the bandwidth
dependency on closed loop gain isn’t as severe as that of a
voltage feedback amplifier, there can be an appreciable
decrease in bandwidth at higher gains. This decrease may
be minimized by taking advantage of the current feedback
amplifier’s unique relationship between bandwidth and RF.
All current feedback amplifiers require a feedback resistor,
even for unity gain applications, and RF, in conjunction with
the internal compensation capacitor, sets the dominant pole
of the frequency response. Thus, the amplifier’s bandwidth is
inversely proportional to RF. The HA5023 design is
optimized for a 1000Ω RF at a gain of +1. Decreasing RF in
a unity gain application decreases stability, resulting in
excessive peaking and overshoot. At higher gains the
amplifier is more stable, so RF can be decreased in a tradeoff of stability for bandwidth.
The table below lists recommended RF values for various
gains, and the expected bandwidth.
Driving Capacitive Loads
Capacitive loads will degrade the amplifier’s phase margin
resulting in frequency response peaking and possible
oscillations. In most cases the oscillation can be avoided by
placing an isolation resistor (R) in series with the output as
shown in Figure 6.
100Ω
VIN
R
+
VOUT
-
RT
CL
RF
RI
FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION
RESISTOR, R
The selection criteria for the isolation resistor is highly
dependent on the load, but 27Ω has been determined to be
a good starting value.
Power Dissipation Considerations
RF (Ω)
BANDWIDTH
(MHz)
-1
750
100
+1
1000
125
+2
681
95
+5
1000
52
+10
383
65
-10
750
22
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board. The use
of low inductance components such as chip resistors and
chip capacitors is strongly recommended. If leaded
components are used the leads must be kept short
especially for the power supply decoupling components and
those components connected to the inverting input.
Attention must be given to decoupling the power supplies. A
large value (10µF) tantalum or electrolytic capacitor in
parallel with a small value (0.1µF) chip capacitor works well
in most cases.
A ground plane is strongly recommended to control noise.
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input (-IN). The
larger this capacitance, the worse the gain peaking, resulting
in pulse overshoot and possible instability. It is
recommended that the ground plane be removed under
7
Due to the high supply current inherent in dual amplifiers, care
must be taken to insure that the maximum junction
temperature (TJ , see Absolute Maximum Ratings) is not
exceeded. Figure 7 shows the maximum ambient
temperature versus supply voltage for the available package
styles (Plastic DIP, SOIC). At ±5VDC quiescent operation both
package styles may be operated over the full industrial range
of -40°C to 85°C. It is recommended that thermal calculations,
which take into account output power, be performed by the
designer.
MAX AMBIENT TEMPERATURE (°C)
GAIN
(ACL)
140
130
120
PDIP
110
100
90
SOIC
80
70
60
50
5
7
9
11
13
15
SUPPLY VOLTAGE (±V)
FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE
vs SUPPLY VOLTAGE
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
Unless Otherwise Specified
5
5
VOUT = 0.2VP-P
CL = 10pF
4
AV = +1, RF = 1kΩ
AV = 2, RF = 681Ω
2
3
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
AV = 5, RF = 1kΩ
1
0
-1
-2
-3
VOUT = 0.2VP-P
CL = 10pF
RF = 750Ω
4
AV = 10, RF = 383Ω
-4
AV = -1
2
1
AV = -2
0
-1
-2
AV = -10
-3
AV = -5
-4
-5
10
100
-5
200
FREQUENCY (MHz)
2
180
AV = +1, RF = 1kΩ
135
-45
90
AV = -1, RF = 750Ω
-135
45
AV = +10, RF = 383Ω
-100
0
-225
-45
-270
-90
AV = -10, RF = 750Ω
VOUT = 0.2VP-P
CL = 10pF
2
140
VOUT = 0.2VP-P
CL = 10pF
AV = +1
130
120
5
-180
10
100
GAIN PEAKING
500
200
700
FREQUENCY (MHz)
0
1500
130
VOUT = 0.2VP-P
CL = 10pF
AV = +2
95
-3dB BANDWIDTH
90
10
5
GAIN PEAKING
500
650
800
950
0
1100
FEEDBACK RESISTOR (Ω)
FIGURE 12. BANDWIDTH AND GAIN PEAKING vs FEEDBACK
RESISTANCE
8
-3dB BANDWIDTH (MHz)
100
GAIN PEAKING (dB)
-3dB BANDWIDTH (MHz)
900
1100
1300
FEEDBACK RESISTOR (Ω)
FIGURE 11. BANDWIDTH AND GAIN PEAKING vs FEEDBACK
RESISTANCE
FIGURE 10. PHASE RESPONSE AS A FUNCTION OF
FREQUENCY
350
10
-3dB BANDWIDTH
-135
-315
-360
200
120
-3dB BANDWIDTH
110
6
100
4
90
GAIN PEAKING
80
0
200
400
VOUT = 0.2VP-P
CL = 10pF
AV = +1
600
800
2
GAIN PEAKING (dB)
-90
INVERTING PHASE (°)
NONINVERTING PHASE (°)
0
100
FIGURE 9. INVERTING FREQUENCY RESPONSE
-3dB BANDWIDTH (MHz)
FIGURE 8. NON-INVERTING FREQENCY RESPONSE
10
FREQUENCY (MHz)
GAIN PEAKING (dB)
2
0
1000
LOAD RESISTOR (Ω)
FIGURE 13. BANDWIDTH AND GAIN PEAKING vs LOAD
RESISTANCE
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
Unless Otherwise Specified (Continued)
16
VOUT = 0.1VP-P
CL = 10pF
VOUT = 0.2VP-P
CL = 10pF
AV = +10
VSUPPLY = ±5V, AV = +2
60
OVERSHOOT (%)
-3dB BANDWIDTH (MHz)
80
40
12
VSUPPLY = ±15V, AV = +2
6
20
VSUPPLY = ±5V, AV = +1
VSUPPLY = ±15V, AV = +1
0
0
200
350
500
650
800
0
950
200
400
600
LOAD RESISTANCE (Ω)
FEEDBACK RESISTOR (Ω)
0.08
0.10
FREQUENCY = 3.58MHz
0.08
DIFFERENTIAL PHASE (°)
FREQUENCY = 3.58MHz
DIFFERENTIAL GAIN (%)
1000
FIGURE 15. SMALL SIGNAL OVERSHOOT vs LOAD
RESISTANCE
FIGURE 14. BANDWIDTH vs FEEDBACK RESISTANCE
RL = 75Ω
0.06
RL = 150Ω
0.04
0.02
0.06
0.04
RL = 150Ω
RL = 75Ω
0.02
RL = 1kΩ
RL = 1kΩ
0.00
0.00
3
5
7
9
11
13
3
15
5
SUPPLY VOLTAGE (±V)
-40
VOUT = 2.0VP-P
CL = 30pF
0
REJECTION RATIO (dB)
HD2
-60
3RD ORDER IMD
HD2
HD3
15
AV = +1
-20
-30
-40
-50
CMRR
-60
NEGATIVE PSRR
-70
-80
-80
HD3
-90
0.3
13
-10
-50
-70
7
9
11
SUPPLY VOLTAGE (±V)
FIGURE 17. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE
FIGURE 16. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE
DISTORTION (dBc)
800
1
FREQUENCY (MHz)
FIGURE 18. DISTORTION vs FREQUENCY
9
10
0.001
POSITIVE PSRR
0.01
0.1
1
10
30
FREQUENCY (MHz)
FIGURE 19. REJECTION RATIOS vs FREQUENCY
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
Unless Otherwise Specified (Continued)
12
8.0
RLOAD = 100Ω
VOUT = 1.0VP-P
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
RL = 100Ω
VOUT = 1.0VP-P
AV = +1
7.5
7.0
6.5
10
AV = +10, RF = 383Ω
8
AV = +2, RF = 681Ω
6
AV = +1, RF = 1kΩ
6.0
-50
-25
0
25
50
75
100
4
125
3
5
7
9
11
SUPPLY VOLTAGE (±V)
TEMPERATURE (C)
FIGURE 20. PROPAGATION DELAY vs TEMPERATURE
15
FIGURE 21. PROPAGATION DELAY vs SUPPLY VOLTAGE
500
0.8
VOUT = 2VP-P
NORMALIZED GAIN (dB)
+ SLEW RATE
400
VOUT = 0.2VP-P
CL = 10pF
0.6
450
SLEW RATE (V/µs)
13
350
- SLEW RATE
300
250
200
0.4
0.2
AV = +2, RF = 681Ω
0
-0.2
-0.4
AV = +5, RF = 1kΩ
-0.6
AV = +1, RF = 1kΩ
-0.8
150
-1.0
100
AV = +10, RF = 383Ω
-1.2
-25
0
25
50
75
100
125
5
10
TEMPERATURE (°C)
FIGURE 22. FIGURE 22. SLEW RATE vs TEMPERATURE
VOLTAGE NOISE (nV/√Hz)
NORMALIZED GAIN (dB)
0
AV = -1
-0.2
-0.4
-0.6
AV = -5
-0.8
-1.2
10
-INPUT NOISE CURRENT
80
800
600
60
+INPUT NOISE CURRENT
400
40
INPUT NOISE VOLTAGE
200
20
AV = -2
AV = -10
5
1000
AV = +10, RF = 383Ω
0.2
-1.0
30
100
VOUT = 0.2VP-P
CL = 10pF
RF = 750Ω
0.4
25
FIGURE 23. NON-INVERTING GAIN FLATNESS vs FREQUENCY
0.8
0.6
15
20
FREQUENCY (MHz)
CURRENT NOISE (pA/√Hz)
-50
15
20
25
30
FREQUENCY (MHz)
FIGURE 24. INVERTING GAIN FLATNESS vs FREQUENCY
10
0
0.01
0.1
1
FREQUENCY (kHz)
10
0
100
FIGURE 25. INPUT NOISE CHARACTERISTICS
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
Unless Otherwise Specified (Continued)
1.5
BIAS CURRENT (µA)
2
VIO (mV)
1.0
0.5
0.0
-60
-40
-20
0
20
40
60
80
100
120
0
-2
-4
-60
140
-40
-20
0
TEMPERATURE (°C)
TRANSIMPEDANCE (kΩ)
BIAS CURRENT (µA)
60
80
100
120
140
4000
22
20
18
16
-60
-40
-20
0
20
40
60
80
100
120
140
3000
2000
1000
-60
-40
-20
0
TEMPERATURE (°C)
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 28. -INPUT BIAS CURRENT vs TEMPERATURE
FIGURE 29. TRANSIMPEDANCE vs TEMPERATURE
74
25
+PSRR
72
20
REJECTION RATIO (dB)
125°C
ICC (mA)
40
FIGURE 27. +INPUT BIAS CURRENT vs TEMPERATURE
FIGURE 26. INPUT OFFSET VOLTAGE vs TEMPERATURE
55°C
15
10
3
4
5
6
7
70
68
-PSRR
66
64
62
CMRR
60
25°C
5
20
TEMPERATURE (°C)
8
9
10
11
12
13
14
SUPPLY VOLTAGE (±V)
FIGURE 30. SUPPLY CURRENT vs SUPPLY VOLTAGE
11
15
58
-100
-50
0
50
100
150
200
250
TEMPERATURE (°C)
FIGURE 31. REJECTION RATIO vs TEMPERATURE
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
Unless Otherwise Specified (Continued)
4.0
30
+15V
+10V
+5V
OUTPUT SWING (V)
SUPPLY CURRENT (mA)
40
20
3.8
10
0
0
1
2
3
4
5
6
7
8
9
3.6
-60
10 11 12 13 14 15
-40
-20
0
DISABLE INPUT VOLTAGE (V)
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 32. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE
FIGURE 33. OUTPUT SWING vs TEMPERATURE
30
1.2
VCC = ±15V
1.1
VIO (mV)
VOUT (VP-P)
20
VCC = ±10V
1.0
10
0.9
VCC = ±4.5V
0.8
0
0.01
0.10
1.00
10.00
-60
-40
-20
LOAD RESISTANCE (kΩ)
0
20
40
60
80
100
120
140
TEMPERATURE (°C)
FIGURE 34. OUTPUT SWING vs LOAD RESISTANCE
FIGURE 35. INPUT OFFSET VOLTAGE CHANGE BETWEEN
CHANNELS vs TEMPERATURE
-30
1.5
AV = +1
VOUT = 2VP-P
SEPARATION (dB)
∆BIAS CURRENT (µA)
-40
1.0
0.5
-50
-60
-70
0.0
-60
-40
-20
0
20
40
60
80
100
120
TEMPERATURE (°C)
FIGURE 36. INPUT BIAS CURRENT CHANGE BETWEEN
CHANNELS vs TEMPERATURE
12
140
-80
0.1
1
FREQUENCY (MHz)
10
30
FIGURE 37. CHANNEL SEPARATION vs FREQUENCY
FN3393.8
June 2, 2006
HA5023
Typical Performance Curves
VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25°C,
-20
-30
-40
-50
10
RL = 100Ω
1
0.1
0.01
180
0.001
135
90
45
-60
0
-70
-45
-80
-90
1
FREQUENCY (MHz)
10
FIGURE 38. DISABLE FEEDTHROUGH vs FREQUENCY
20
0.001
0.01
0.1
1
FREQUENCY (MHz)
10
100
-135
FIGURE 39. TRANSIMPEDANCE vs FREQUENCY
10
RL = 400Ω
1
0.1
0.01
180
0.001
135
90
45
0
-45
PHASE ANGLE (°)
0.1
TRANSIMPEDANCE (MΩ)
FEEDTHROUGH (dB)
-10
DISABLE = 0V
VIN = 5VP-P
RF = 750Ω
PHASE ANGLE (°)
0
TRANSIMPEDANCE (MΩ)
Unless Otherwise Specified (Continued)
-90
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
-135
FIGURE 40. TRANSIMPEDENCE vs FREQUENCY
13
FN3393.8
June 2, 2006
HA5023
Die Characteristics
SUBSTRATE POTENTIAL (Powered Up):
V-
DIE DIMENSIONS:
PASSIVATION:
1650µm x 2540µm x 483µm
Type: Nitride
Thickness: 4kÅ ±0.4kÅ
METALLIZATION:
Type: Metal 1: AlCu (1%)
Thickness: Metal 1: 8kÅ ±0.4kÅ
TRANSISTOR COUNT:
124
Type: Metal 2: AlCu (1%)
Thickness: Metal 2: 16kÅ ±0.8kÅ
PROCESS:
High Frequency Bipolar Dielectric Isolation
Metallization Mask Layout
HA5023
OUT
NC
V+
-IN1
+IN1
NC
OUT2
NC
V-
+IN
14
-IN
FN3393.8
June 2, 2006
HA5023
Dual-In-Line Plastic Packages (PDIP)
E8.3 (JEDEC MS-001-BA ISSUE D)
N
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
-B-
-AD
E
BASE
PLANE
-C-
SEATING
PLANE
A2
A
L
D1
e
B1
D1
A1
eC
B
0.010 (0.25) M
C A B S
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8, 10
eA
C
0.008
0.014
0.204
C
D
0.355
0.400
9.01
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
eA
0.300 BSC
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
eB
-
L
0.115
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
5
D1
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
0.355
10.16
N
8
2.54 BSC
7.62 BSC
0.430
-
0.150
2.93
8
6
10.92
7
3.81
4
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
15
FN3393.8
June 2, 2006
HA5023
Small Outline Plastic Packages (SOIC)
M8.15 (JEDEC MS-012-AA ISSUE C)
N
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B-
1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
MIN
MAX
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
A1
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.1890
0.1968
4.80
5.00
3
E
0.1497
0.1574
3.80
4.00
4
e
α
B S
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
N
α
NOTES:
MILLIMETERS
8
0°
8
8°
0°
7
8°
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN3393.8
June 2, 2006