SHOULDER HDF137.5A

规格书编号
SPEC NO :
产品规格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF137.5A F11
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2006-5-11
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 1 of 5
SAW FILTER
HDF137.5A F11
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880
Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 5
SAW FILTER
HDF137.5A F11
1. SCOPE
This specification shall cover the characteristics of SAW filter With F137.5A used for the page
system.
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-40℃ to +80℃
-45℃ to +85℃
0dBm
Electronic Characteristics
2-1.Typical frequency response
2-2.Electrical characteristics
Part Number
Nominal center frequency(Fo)
Insertion (Fo)
1. DC.~Fo-10.7MHz
2. Fo
3. Fo+10.7MHz~100MHz
Passband width
Ripple(within passband)
Input/Output impedance(Nominal)
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
F137.5A
137.5
-40 min
-4.5 min
-40 min
±1.5 min
2.0 min
50//0
E-mail:[email protected]
Unit
MHz
dB
MHz
dB
Ω//pF
Page 3 of 5
SAW FILTER
HDF137.5A F11
3. TEST CIRCUIT
4. DIMENSION
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 4 of 5
SAW FILTER
HDF137.5A F11
5. ENVIRONMENTAL CHARACTERISTICS
5-1 High temperature exposure
Subject the filter to +85℃ for 96 hours. Then release the filter into the room
conditions for 1 to 2 hours prior to the measurement. It shall fulfill the specifications in 2-2.
5-2 Moisture
Keep the filter at 40℃ and 95% rh for 96 hours. Then release the filter into the room
conditions for 1 to 2 hours prior to the measurement. It shall fulfill the specifications in 2-2.
5-3 Low temperature exposure
Subject the filter to -40℃ for 96 hours. Then release the filter into the room
conditions for 1 to 2 hours prior to the measurement. It shall fulfill the specifications in 2-2.
5-4 Temperature cycling
Subject the filter to a low temperature of -40℃ for 30 minutes. Following by a high
temperature of +85℃ for 30 Minutes. Then release the filter into the room conditions for 1
to 2 hours prior to the measurement. It shall meet the specifications in 2-2.
5-5 Resistance to solder heat
Dip the filter terminals no closer than 1.5mm into the solder bath at 270℃ ±10℃
for 10±1 sec. Then release the Filter into the room conditions for 1 to 2 hours. The Filter
shall meet the specifications in 2-2.
5-6 Mechanical shock
Drop the filter randomly onto the concrete floor from the height of 30cm 3 times. the
filter shall fulfill the specifications in 2-2.
5-7 Vibration
Subject the filter to the vibration for 1 hour each in x,y and z axes with the amplitude
of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2-2.
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of the
component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid
ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 5 of 5