HMC814 v00.1109 FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Typical Applications Features The HMC814 is ideal for: High Output Power: +17 dBm • Clock Generation Applications: SONET OC-192 & SDH STM-64 Low Input Power Drive: 0 to +6 dBm • Point-to-Point & VSAT Radios Fo Isolation: >20 dBc @ Fout = 19 GHz 100 kHz SSB Phase Noise: -136 dBc/Hz • Test Instrumentation Single Supply: +5V @ 88mA • Military & Space Die Size: 1.2 x 1.23 x 0.1 mm • Sensors Functional Diagram General Description The HMC814 is a x2 active broadband frequency multiplier chip utilizing GaAs PHEMT technology. When driven by a +4 dBm signal, the multiplier provides +17 dBm typical output power from 13 to 24.6 GHz. The Fo, 3Fo and 4Fo isolations are >20 dBc at 19 GHz. The HMC814 is ideal for use in LO multiplier chains for Pt-to-Pt & VSAT Radios yielding reduced parts count vs. traditional approaches. The low additive SSB Phase Noise of -136 dBc/Hz at 100 kHz offset helps maintain good system noise performance. All data is taken with the chip connected via two 0.025mm (1 mil) wire bonds of minimal length 0.31 mm (12 mils). Electrical Specifi cations, TA = +25 °C, Vdd1, Vdd2 = +5V, +4 dBm Drive Level Parameter Min. Frequency Range, Input Frequency Range, Output Max. Units GHz 13.0 - 24.6 GHz 17 dBm Fo Isolation (with respect to output level) 25 dBc 3Fo Isolation (with respect to output level) 25 dBc Input Return Loss 7 dB Output Return Loss 7 dB -136 dBc/Hz Output Power 14 SSB Phase Noise (100 kHz Offset @ Input Frequency = 19 GHz) Supply Current (Idd1 & Idd2) 2 - 68 Typ. 6.5 - 12.3 70 88 100 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC814 v00.1109 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Output Power vs. Drive Level 25 16 15 12 +25C +85C -55C 8 4 0 dBm 1 dBm 2 dBm 3 dBm 4 dBm 5 dBm 6 dBm 5 -5 -15 -25 0 12.5 2 14.5 16.5 18.5 20.5 22.5 24.5 12.5 26.5 14.5 16.5 16 10 OUTPUT POWER (dBm) 20 12 4.5V 5.0V 5.5V 4 0 12.5 20.5 22.5 24.5 26.5 24.5 26.5 Isolation @ +4 dBm Drive Level 20 0 -10 Fo 2 Fo 3 Fo 4 Fo -20 -30 14.5 16.5 18.5 20.5 22.5 24.5 26.5 12.5 14.5 16.5 FREQUENCY (GHz) 18.5 20.5 22.5 FREQUENCY (GHz) Output Power vs. Input Power 20 OUTPUT POWER (dBm) OUTPUT POWER (dBm) Output Power vs. Supply Voltage @ +4 dBm Drive Level 8 18.5 FREQUENCY (GHz) FREQUENCY (GHz) FREQUENCY MULTIPLIERS - ACTIVE - CHIP 20 OUTPUT POWER (dBm) OUTPUT POWER (dBm) Output Power vs. Temperature @ +4 dBm Drive Level 15 15 GHz 19 GHz 23 GHz 24 GHz 10 5 0 0 1 2 3 4 5 6 7 8 9 10 INPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 2 - 69 HMC814 v00.1109 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Output Return Loss vs. Temperature 2 - 70 0 -5 -5 RETURN LOSS (dB) 0 -10 -15 +25C +85C -55C -20 -25 -10 -15 +25C +85C -55C -20 -25 -30 -30 6 7 8 9 10 11 12 13 12.5 14.5 16.5 FREQUENCY (GHz) 18.5 20.5 22.5 24.5 26.5 FREQUENCY (GHz) Phase Noise @ 19 GHz -10 -30 PHASE NOISE (dBc/Hz) FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 RETURN LOSS (dB) Input Return Loss vs. Temperature -50 -70 -90 -110 -130 -150 -170 2 10 10 3 10 4 10 5 10 6 10 7 10 8 FREQUENCY (Hz) Absolute Maximum Ratings RF Input (Vdd = +5V) Typical Supply Current vs. Vdd +10 dBm Vdd (Vdc) Idd (mA) Supply Voltage (Vdd1, Vdd2) +5.5 Vdc 4.5 87 Channel Temperature 175 °C 5.0 88 Continuous Pdiss (T= 85 °C) (derate 8.7 mW/°C above 85 °C) 782 mW 5.5 89 Thermal Resistance (channel to die bottom) 115 °C/W Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC814 v00.1109 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Outline Drawing NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM] 2. DIE THICKNESS IS .004” 3. TYPICAL BOND PAD IS .004” SQUARE 4. BOND PAD METALIZATION: GOLD 5. BACKSIDE METALIZATION: GOLD 6. BACKSIDE METAL IS GROUND 7. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS 8. OVERALL DIE SIZE ±.002” For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 2 - 71 HMC814 v00.1109 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Pin Description FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 2 - 72 Pin Number Function Description 1 RFIN Pin is AC coupled and matched to 50 Ohms. 2, 3 Vdd1, Vdd2 Supply voltage 5V ± 0.5V. External bypass capacitors of 100 pF, 1,000 pF and 2.2 μF are recommended. 4 RFOUT Pin is AC coupled and matched to 50 Ohms. Interface Schematic Assembly Diagram For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC814 v00.1109 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 13 - 24.6 GHz OUTPUT Mounting & Bonding Techniques for Millimeterwave GaAs MMICs 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Wire 3 mil Ribbon Bond 0.076mm (0.003”) RF Ground Plane Microstrip substrates should be brought as close to the die as possible in order to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is recommended to minimize inductance on RF, LO & IF ports. 0.127mm (0.005”) Thick Alumina Thin Film Substrate An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer capacitor (mounted eutectically or by conductive epoxy) placed no further than 0.762mm (30 Mils) from the chip is recommended. Handling Precautions Figure 1. 0.102mm (0.004”) Thick GaAs MMIC Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Static Sensitivity: Follow ESD precautions to protect against > ± 250V ESD strikes. 2 Ribbon Bond 0.076mm (0.003”) RF Ground Plane 0.150mm (0.005”) Thick Moly Tab 0.254mm (0.010”) Thick Alumina Thin Film Substrate Figure 2. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. FREQUENCY MULTIPLIERS - ACTIVE - CHIP The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of 150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 2 - 73