M68AW256DL 4 Mbit (256K x16) 3.0V Asynchronous SRAM FEATURES SUMMARY ■ SUPPLY VOLTAGE: 2.7 to 3.6V ■ 256K x 16 bits SRAM with OUTPUT ENABLE ■ EQUAL CYCLE and ACCESS TIME: 55ns ■ SINGLE BYTE READ/WRITE ■ LOW STANDBY CURRENT ■ LOW VCC DATA RETENTION: 1.5V ■ TRI-STATE COMMON I/O ■ AUTOMATIC POWER DOWN ■ DUAL CHIP ENABLE for EASY DEPTH EXPANSION Figure 1. Packages 44 1 TSOP44 Type II (ND) BGA TFBGA48 (ZB) 7 x 8 mm June 2002 1/20 M68AW256DL TABLE OF CONTENTS SUMMARY DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table 1. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 3. TSOP Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 4. TFBGA Connections (Top view through package). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 5. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table 2. Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 3. Operating and AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 6. AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 7. AC Measurement Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 4. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 5. DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 6. Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 8. Address Controlled, Read Mode AC Waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 9. Chip Enable or Output Enable Controlled, Read Mode AC Waveforms. . . . . . . . . . . . . . 10 Figure 10. Chip Enable or UB/LB Controlled, Standby Mode AC Waveforms . . . . . . . . . . . . . . . . 10 Table 7. Read and Standby Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Write Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 11. Write Enable Controlled, Write AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 12. Chip Enable Controlled, Write AC Waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 13. UB/LB Controlled, Write AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 8. Write Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 14. E1 Controlled, Low VCC Data Retention AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 15. E2 Controlled, Low VCC Data Retention AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . 15 Table 9. Low VCC Data Retention Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 TSOP44 Type II - 44 lead Plastic Thin Small Outline Type II, Package Outline . . . . . . . . . . . . . . . 16 TSOP 44 Type II - 44 lead Plastic Thin Small Outline Type II, Package Mechanical Data . . . . . . . 16 TFBGA48 7x8mm - 6x8 ball array, 0.75 mm pitch, Bottom View Package Outline. . . . . . . . . . . . . 17 TFBGA48 7x8mm - 6x8 ball array, 0.75 mm pitch, Package Mechanical Data. . . . . . . . . . . . . . . . 17 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Table 12. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Table 13. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 M68AW256DL SUMMARY DESCRIPTION The M68AW256DL is a 4 Mbit (4,194,304 bit) CMOS SRAM, organized as 262,144 words by 16 bits. The device features fully static operation requiring no external clocks or timing strobes, with equal address access and cycle times. It requires a single 2.7 to 3.6V supply. This device has an au- tomatic power-down feature, reducing the power consumption by over 99% when deselected. The M68AW256DL is available in TFBGA48 (0.75 mm pitch) and in TSOP44 Type II packages. Figure 2. Logic Diagram Table 1. Signal Names A0-A17 Address Inputs DQ0-DQ15 Data Input/Output E1, E2 Chip Enables G Output Enable W Write Enable UB Upper Byte Enable Input LB Lower Byte Enable Input VCC Supply Voltage VSS Ground UB NC Not Connected Internally LB DU Don’t Use as Internally Connected VCC 18 16 A0-A17 DQ0-DQ15 W E1 E2 M68AW256DL G VSS AI05492 3/20 M68AW256DL Figure 3. TSOP Connections A4 A3 A2 A1 A0 E1 DQ0 DQ1 DQ2 DQ3 VCC VSS DQ4 DQ5 DQ6 DQ7 W A16 A15 A14 A13 A12 1 44 2 43 3 42 4 41 5 40 6 39 7 38 8 37 9 36 10 35 11 34 M68AW256DL 12 33 13 32 14 31 15 30 16 29 17 28 18 27 19 26 20 25 21 24 22 23 AI05493 4/20 A5 A6 A7 G UB LB DQ15 DQ14 DQ13 DQ12 VSS VCC DQ11 DQ10 DQ9 DQ8 E2 A8 A9 A10 A11 A17 M68AW256DL Figure 4. TFBGA Connections (Top view through package) 1 2 3 4 5 6 A LB G A0 A1 A2 E2 B DQ8 UB A3 A4 E1 DQ0 C DQ9 DQ10 A5 A6 DQ1 DQ2 D VSS DQ11 A17 A7 DQ3 VCC E VCC DQ12 NC A16 DQ4 VSS F DQ14 DQ13 A14 A15 DQ5 DQ6 G DQ15 NC A12 A13 W DQ7 H NC A8 A9 A10 A11 DU AI05494 5/20 M68AW256DL Figure 5. Block Diagram A17 ROW DECODER MEMORY ARRAY A7 DQ15 (8) I/O CIRCUITS UB COLUMN DECODER DQ0 E1 Ex E2 (8) LB UB LB A0 A6 (8) UB W (8) LB G AI05495 MAXIMUM RATING Stressing the device above the rating listed in the Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not im- plied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 2. Absolute Maximum Ratings Symbol Value Unit 20 mA Ambient Operating Temperature –55 to 125 °C TSTG Storage Temperature –65 to 150 °C V CC Supply Voltage –0.5 to 4.6 V –0.5 to VCC +0.5 V 1 W IO (1) TA VIO (2) PD Parameter Output Current Input or Output Voltage Power Dissipation Note: 1. One output at a time, not to exceed 1 second duration. 2. Up to a maximum operating VCC of 3.6V only. 6/20 M68AW256DL DC AND AC PARAMETERS This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC Characteristic tables are derived from tests performed under the Measure- ment Conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 3. Operating and AC Measurement Conditions Parameter M68AW256ML VCC Supply Voltage 2.7 to 3.6V Range 1 0 to 70°C Range 6 –40 to 85°C Ambient Operating Temperature Load Capacitance (CL) 30pF Output Circuit Protection Resistance (R1) 3.0kΩ Load Resistance (R 2) 3.1kΩ Input Rise and Fall Times 1ns/V 0 to VCC Input Pulse Voltages Input and Output Timing Ref. Voltages VCC/2 Output Transition Timing Ref. Voltages VRL = 0.3VCC; VRH = 0.7VCC Figure 6. AC Measurement I/O Waveform Figure 7. AC Measurement Load Circuit VCC I/O Timing Reference Voltage R1 VCC VCC/2 0V DEVICE UNDER TEST OUT CL I/O Transition Timing Reference Voltage VCC 0V R2 0.7VCC 0.3VCC AI04831 CL includes probe and 1 TTLcapacitance AI05832 7/20 M68AW256DL Table 4. Capacitance C IN Test Conditio n Parameter (1,2) Symbol Max Unit VIN = 0V 8 pF VOUT = 0V 10 pF Input Capacitance on all pins (except DQ) C OUT(3) Output Capacitance Min Note: 1. Sampled only, not 100% tested. 2. At TA = 25°C, f = 1 MHz, VCC = 3.0V. 3. Outputs deselected. Table 5. DC Characteristics Symbol Parameter ICC1 (1,2) Operating Supply Current ICC2 (3) Operating Supply Current ISB Standby Supply Current CMOS ILI Input Leakage Current ILO (4) Output Leakage Current Test Condition VCC = 3.6V, f = 1/tAVAV, IOUT = 0mA Min Typ Max Unit 70ns 20 mA 55ns 26 mA 2 mA 10 µA VCC = 3.6V, f = 1MHz, I OUT = 0mA V CC = 3.6V, f = 0, E1 ≥ VCC –0.2V or E2 ≤ 0.2V or LB=UB ≥ VCC –0.2V 5 0V ≤ VIN ≤ V CC –1 1 µA 0V ≤ VOUT ≤ VCC –1 1 µA VIH Input High Voltage 2.2 VCC + 0.3 V V IL Input Low Voltage –0.3 0.6 V VOH Output High Voltage IOH = –1.0mA VOL Output Low Voltage IOL = 2.1mA Note: 1. 2. 3. 4. 8/20 Average AC current, cycling at tAVAV minimum. E1 = VIL, E2 = VIH, LB or/and UB = VIL, VIN = VIL or VIH. E1 ≤ 0.2V or E2 ≥ VCC –0.2V, LB or/and UB ≤ 0.2V, VIN ≤ 0.2V or VIN ≥ VCC –0.2V. Output disabled. 2.4 V 0.4 V M68AW256DL OPERATION The M68AW256DL has a Chip Enable power down feature which invokes an automatic standby mode whenever Chip Enable is de-asserted (E1 = High) or Chip Select is asserted (E2 = Low), or UB/ LB are de-asserted (UB/LB = High). An Output Enable (G) signal provides a high speed tri-state con- trol, allowing fast read/write cycles to be achieved with the common I/O data bus. Operational modes are determined by device control inputs W, E1, LB and UB as summarized in the Operating Modes table (see Table 6). Table 6. Operating Modes Operation E1 E2 W G LB UB DQ0-DQ7 DQ8-DQ15 Power Deselected VIH X X X X X Hi-Z Hi-Z Standby (ISB) Deselected X VIL X X X X Hi-Z Hi-Z Standby (ISB) Deselected X X X X VIH VIH Hi-Z Hi-Z Standby (ISB) Lower Byte Read V IL VIH VIH VIL VIL VIH Data Output Hi-Z Active (ICC) Lower Byte Write V IL VIH VIL X VIL VIH Data Input Hi-Z Active (ICC) Output Disabled V IL VIH VIH VIH X X Hi-Z Hi-Z Active (ICC) Upper Byte Read V IL VIH VIH VIL VIH VIL Hi-Z Data Output Active (ICC) Upper Byte Write V IL VIH VIL X VIH VIL Hi-Z Data Input Active (ICC) Word Read V IL VIH VIH VIL VIL VIL Data Output Data Output Active (ICC) Word Write V IL VIH VIL X VIL VIL Data Input Data Input Active (ICC) Note: X = VIH or VIL. Read Mode The M68AW256DL, when Chip Select (E2) is High, is in the read mode whenever Write Enable (W) is High with Output Enable (G) Low, and Chip Enable (E1) is asserted. This provides access to data from eight or sixteen, depending on the status of the signal UB and LB, of the 4,194,304 locations in the static memory array, specified by the 18 address inputs. Valid data will be available at the eight or sixteen output pins within tAVQV after the last stable address, providing G is Low and E1 is Low. If Chip Enable or Output Enable access times are not met, data access will be measured from the limiting parameter (tELQV, tGLQV or tBLQV) rather than the address. Data out may be indeterminate at tELQX, tGLQX and tBLQX, but data lines will always be valid at tAVQV. Figure 8. Address Controlled, Read Mode AC Waveforms tAVAV A0-A17 VALID tAVQV DQ0-DQ7 and/or DQ8-DQ15 tAXQX DATA VALID AI03956 Note: E1 = Low, E2 = High, G = Low, W = High, UB = Low and/or LB = Low. 9/20 M68AW256DL Figure 9. Chip Enable or Output Enable Controlled, Read Mode AC Waveforms. tAVAV A0-A17 VALID tAVQV tAXQX tELQV tEHQZ E1 E2 tELQX tGLQV tGHQZ G tGLQX DQ0-DQ15 VALID tBLQV tBHQZ UB, LB tBLQX AI05496 Note: Writ e Enable (W) = High. Figure 10. Chip Enable or UB/LB Controlled, Standby Mode AC Waveforms E1, UB, LB E2 ICC ISB tPU tPD 50% AI05497 10/20 M68AW256DL Table 7. Read and Standby Mode AC Characteristics M68AW256DL Symbol Parameter Unit 55 70 tAVAV Read Cycle Time Min 55 70 ns tAVQV Address Valid to Output Valid Max 55 70 ns Data hold from address change Min 5 5 ns tBHQZ (2,3) Upper/Lower Byte Enable High to Output Hi-Z Max 20 25 ns tBLQV Upper/Lower Byte Enable Low to Output Valid Max 55 70 ns Upper/Lower Byte Enable Low to Output Transition Min 5 5 ns tEHQZ (2,3) Chip Enable High to Output Hi-Z Max 20 25 ns tELQV Chip Enable Low to Output Valid Max 55 70 ns Chip Enable Low to Output Transition Min 5 5 ns tGHQZ (2,3) Output Enable High to Output Hi-Z Max 20 25 ns tGLQV Output Enable Low to Output Valid Max 25 35 ns Output Enable Low to Output Transition Min 5 5 ns tPD (4) Chip Enable or UB/LB High to Power Down Max 0 0 ns tPU (4) Chip Enable or UB/LB Low to Power Up Min 55 70 ns tAXQX (1) tBLQX (1) tELQX (1) tGLQX (2) Note: 1. Test conditions assume transition timing reference level = 0.3VCC or 0.7VCC. 2. At any given temperature and voltage condition, tGHQZ is less than tGLQX, tBHQZ is less than tBLQX and tEHQZ is less than tELQX for any given device. 3. These parameters are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 4. Tested initially and after any design or process changes that may affect these parameters. 11/20 M68AW256DL Write Mode The M68AW256DL, when Chip Select (E2) is High, is in the Write Mode whenever the W and E1 are Low. Either the Chip Enable Input (E1) or the Write Enable input (W) must be de-asserted during Address transitions for subsequent write cycles. When E1 or W is Low, and UB or LB is Low, write cycle begins on the W or E1 falling edge. When E1 and W are Low, and UB = LB = High, write cycle begins on the first falling edge of UB or LB. Therefore, address setup time is referenced to Write Enable, Chip Enables and UB/LB as tAVWL, tAVEL and tAVBL respectively, and is determined by the latter occurring falling edge. The Write cycle can be terminated by the earlier rising edge of E1, W, UB and LB. If the Output is enabled (E1 = Low, E2 = High, G = Low, LB or UB = Low), then W will return the outputs to high impedance within tWLQZ of its falling edge. Care must be taken to avoid bus contention in this type of operation. Data input must be valid for tDVWH before the rising edge of Write Enable, or for tDVEH before the rising edge of E1 or for tDVBH before the rising edge of UB/LB, whichever occurs first, and remain valid for tWHDX, tEHDX and tBHDX respectively. Figure 11. Write Enable Controlled, Write AC Waveforms tAVAV A0-A17 VALID tAVWH tAVEL tELWH tWHAX E1 E2 tWLWH tAVWL W tWLQZ tWHQX tWHDX DQ0-DQ15 DATA INPUT tDVWH tBLBH UB, LB AI05498 12/20 M68AW256DL Figure 12. Chip Enable Controlled, Write AC Waveforms tAVAV A0-A17 VALID tAVEH tAVEL tELEH tEHAX E1 E2 tAVWL tWLEH W tEHDX DQ0-DQ15 DATA INPUT tDVEH tBLBH UB, LB AI05425 Figure 13. UB/LB Controlled, Write AC Waveforms tAVAV A0-A17 VALID tAVBH tBHAX E1 E2 tAVWL tWLBH W tWLQZ DQ0-DQ15 tBHDX DATA (1) DATA INPUT tDVBH tAVBL tBLBH UB, LB AI05426 Note: 1. During this period DQ0-DQ15 are in output state and input signals should not be applied. 13/20 M68AW256DL Table 8. Write Mode AC Characteristics M68AW256DL Symbol Parameter Unit 55 70 tAVAV Write Cycle Time Min 55 70 ns tAVBH Address Valid to LB, UB High Min 45 60 ns tAVBL Addess Valid to LB, UB Low Min 0 0 ns tAVEH Address Valid to Chip Enable High Min 45 60 ns tAVEL Address valid to Chip Enable Low Min 0 0 ns tAVWH Address Valid to Write Enable High Min 45 60 ns t AVWL Address Valid to Write Enable Low Min 0 0 ns tBHAX LB, UB High to Address Transition Min 0 0 ns tBHDX LB, UB High to Input Transition Min 0 0 ns tBLBH LB, UB Low to LB, UB High Min 45 60 ns tBLEH LB, UB Low to Chip Enable High Min 45 60 ns tBLWH LB, UB Low to Write Enable High Min 45 60 ns tDVBH Input Valid to LB, UB High Min 25 30 ns tDVEH Input Valid to Chip Enable High Min 25 30 ns tDVWH Input Valid to Write Enable High Min 25 30 ns tEHAX Chip Enable High to Address Transition Min 0 0 ns tEHDX Chip enable High to Input Transition Min 0 0 ns tELBH Chip Enable Low to LB, UB High Min 45 60 ns tELEH Chip Enable Low to Chip Enable High Min 45 60 ns tELWH Chip Enable Low to Write Enable High Min 45 60 ns tWHAX Write Enable High to Address Transition Min 0 0 ns tWHDX Write Enable High to Input Transition Min 0 0 ns Write Enable High to Output Transition Min 5 5 ns tWLBH Write Enable Low to LB, UB High Min 45 60 ns tWLEH Write Enable Low to Chip Enable High Min 45 60 ns Write Enable Low to Output Hi-Z Max 20 20 ns Write Enable Low to Write Enable High Min 45 60 ns tWHQX (1) tWLQZ (1,2) tWLWH Note: 1. At any given temperature and voltage condition, tWLQZ is less than tWHQX for any given device. 2. These parameters are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 14/20 M68AW256DL Figure 14. E1 Controlled, Low VCC Data Retention AC Waveforms DATA RETENTION MODE 3.6V VCC 2.7V VDR > 1.5V tCDR tR E1 ≥ VDR –0.2V or UB=LB > VDR –0.2V E1, UB/LB AI05456 Figure 15. E2 Controlled, Low VCC Data Retention AC Waveforms DATA RETENTION MODE 3.6V VCC 2.7V VDR > 1.5V tCDR tR E2 E2 ≤ 0.2V AI05457 Table 9. Low VCC Data Retention Characteristics Symbol Parameter ICCDR (1) Supply Current (Data Retention) Test Condition Min VCC = 1.5V, E1 ≥ VCC –0.2V or E2 ≤ 0.2V or UB = LB ≥ V CC –0.2V, Typ Max Unit 4.5 9 µA f =0 t CDR (1,2) Chip Deselected to Data Retention Time 0 ns tR (2) Operation Recovery Time tAVAV ns 1.5 V VDR (1) Supply Voltage (Data Retention) E1 ≥ VCC –0.2V or E2 ≤ 0.2V or UB = LB ≥ V CC –0.2V, f = 0 Note: 1. All other Inputs at VIH ≥ VCC –0.2V or VIL ≤ 0.2V. 2. Tested initially and after any design or process changes that may affect these parameters. tAVAV is Read cycle time. 3. No input may exceed VCC +0.2V. 15/20 M68AW256DL PACKAGE MECHANICAL Figure 16. TSOP44 Type II - 44 lead Plastic Thin Small Outline Type II, Package Outline D N E1 E N/2 1 ZD b e A2 A C A1 CP α L TSOP-d Note: Drawing is not to scale. Table 10. TSOP 44 Type II - 44 lead Plastic Thin Small Outline Type II, Package Mechanical Data Symbol millimeters Typ Min A Max Typ Min 1.200 Max 0.0472 A1 0.050 0.150 0.0020 0.0059 A2 0.950 1.050 0.0374 0.0413 0.0047 0.0083 b 0.350 c 0.0138 0.120 0.210 D 18.410 – – 0.7248 – – E 11.760 – – 0.4630 – – E1 10.160 – – 0.4000 – – e 0.800 – – 0.0315 – – L 0.500 0.400 0.600 0.0197 0.0157 0.0236 ZD 0.805 – – 0.0317 – – 0 5 0 5 alfa CP N 16/20 inches 0.100 44 0.0039 44 M68AW256DL Figure 17. TFBGA48 7x8mm - 6x8 ball array, 0.75 mm pitch, Bottom View Package Outline D D1 FD FE SD SE E E1 BALL ”A1” ddd e e b A A2 A1 BGA-Z22 Note: Drawing is not to scale. Table 11. TFBGA48 7x8mm - 6x8 ball array, 0.75 mm pitch, Package Mechanical Data millimeters inches Symbol Typ Min Max A 1.010 1.200 A1 0.260 A2 Typ Min Max 0.0398 0.0472 0.0102 0.950 0.0374 b 0.400 0.300 0.500 0.0157 0.0118 0.0197 D 7.000 6.900 7.100 0.2756 0.2717 0.2795 D1 3.750 – – 0.1476 – – ddd 0.100 0.0039 E 8.000 7.900 8.100 0.3150 0.3110 0.3189 E1 5.250 – – 0.2067 – – e 0.750 – – 0.0295 – – FD 1.625 – – 0.0640 – – FE 1.375 – – 0.0541 – – SD 0.375 – – 0.0148 – – SE 0.375 – – 0.0148 – – 17/20 M68AW256DL PART NUMBERING Table 12. Ordering Information Scheme Example: M68AW256 D L 55 ZB 6 T Device Type M68 Mode A = Asynchronous Operating Voltage W = 2.7 to 3.6V Array Organization 256 = 4 Mbit (256K x16) Optio n 1 D = 2 Chip Enable; Write and Standby from UB and LB Optio n 2 L = Low Leakage Speed Class 55 = 55 ns 70 = 70 ns Package ND = TSOP 44 Type II ZB = TFBGA48: 0.75 mm pitch Operative Temperature 1 = 0 to 70 °C 6 = –40 to 85 °C Shipping T = Tape & Reel Packing For a list of available options (Speed, Package, etc...) or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you. 18/20 M68AW256DL REVISION HISTORY Table 13. Document Revision History Date Version Revision Details February 2002 -01 First Issue 14-Mar-2002 -02 Tables 3, 5, 7 and 9 clarified Figures 3, 8, 9, 11, 12, 13 and 14 clarified 07-Jun-2002 -03 ICCDR clarified (Table 9) ISB clarified (Table 5) 19/20 M68AW256DL Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express writt en approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners. 2002 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com 20/20