MAXIM MAX2644EXT-T

19-1786; Rev 1; 11/03
KIT
ATION
EVALU
E
L
B
A
AVAIL
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
The MAX2644 low-cost, high third-order intercept point
(IP3) low-noise amplifier (LNA) is designed for applications in 2.4GHz WLAN, ISM, and Bluetooth radio systems. It features a programmable bias, allowing the
input IP3 and supply current to be optimized for specific applications. The LNA provides up to +1dBm input
IP3 while maintaining a low noise figure of 2.0dB and a
typical gain of 16dB.
The MAX2644 is designed on a low-noise, advanced
silicon-germanium (SiGe) technology. It operates with a
+2.7V to +5.5V single supply and is available in an
ultra-small 6-pin SC70 package.
Features
♦ Low Noise Figure (2.0dB at 2450MHz)
♦ High Gain: 16dB
♦ Adjustable IP3 and Bias Current
♦ Low-Power Standby Mode
♦ On-Chip Output Matching
♦ +2.7V to +5.5V Single-Supply Operation
♦ Ultra-Small 6-Pin SC70 Package
Ordering Information
________________________Applications
Bluetooth
PART
TEMP RANGE
PINPACKAGE
MAX2644EXT-T
-40°C to +85°C
6 SC70
802.11 WLAN
Home RF
TOP
MARK
AAG
Satellite CD Radio
2.4GHz ISM Band Radios
2.4GHz Cordless Phones
Wireless Local Loop (WLL)
Pin Configuration
Typical Operating Circuit
RBIAS
1.2kΩ
VCC
BIAS
BIAS
BIAS 1
C1
33pF
RFIN
RF INPUT
TOP VIEW
VCC
RFOUT
RF OUTPUT
GND 2
L1
3.3nH
MAX2644
RFIN 3
MAX2644
6
RFOUT
5
GND
4
VCC
SC70-6
GND
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX2644
General Description
MAX2644
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
ABSOLUTE MAXIMUM RATINGS
VCC to GND ..............................................................-0.3V to +6V
RFIN, RFOUT to GND…......................................................±0.3V
RFIN Power (50Ω source) ................................................+5dBm
BIAS to GND ................................................................0 to +0.3V
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Continuous Power Dissipation (TA = +70°C)
6-Pin SC70 (derate 3.1mW/°C above +70°C) ..............245mW
Storage Temperature.........................................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +5.5V, RBIAS = 1.2kΩ, no RF signal applied, RFIN and RFOUT are AC-coupled and terminated to 50Ω, TA = -40°C to
+85°C. Typical values are at VCC = +3.0V, TA = +25 °C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
Supply Voltage
Operating Supply Current
MIN
RBIAS = 3.9kΩ
2.7
RBIAS = 1.2kΩ, TA = +25°C
7.0
RBIAS = 1.2kΩ, TA = -40°C to +85°C
MAX
UNITS
5.5
V
9.7
11.0
RBIAS = 750Ω
Standby Supply Current
TYP
2.7
mA
10.2
RBIAS is unconnected, TA = +25°C, VCC = 3.3V
100
µA
AC ELECTRICAL CHARACTERISTICS
(MAX2644 EV kit, VCC = +3.0V, fRFIN = 2450MHz, PRFIN = -30dBm, input and output are terminated to 50Ω, RBIAS = 1.2kΩ,
TA = +25°C, unless otherwise noted.) (Note 2)
PARAMETER
Operating Frequency
CONDITIONS
(Note 3)
Gain (Note 4)
Gain Variation Over Temperature
Input Third-Order Intercept Point
(Note 5)
TA = -40°C to +85°C
TYP
2400
15
MAX
UNITS
2500
MHz
±1.0
dB
17
±0.7
RBIAS = 750Ω
-4
RBIAS = 1.2kΩ
-3
RBIAS = 3.9kΩ
-8
Input 1dB Compression Point
Noise Figure
MIN
dB
dBm
-13
(Note 6)
2.0
dBm
2.5
dB
Input Return Loss
-15
dB
Output Return Loss
-10
dB
Reverse Isolation
-30
dB
Note 1: Devices are production tested at TA = +25°C. Minimum and maximum values are guaranteed by design and characterization
over temperature and supply voltages.
Note 2: Min/Max limits are guaranteed by design and characterization.
Note 3: The part has been characterized at the specified frequency range. Operation outside this range is possible but not guaranteed.
Note 4: Excluding PC board losses (0.3dB at the input and 0.3dB at the output of the MAX2644 EV kit).
Note 5: Measured with two input tones (f1 = 2445MHz, f2 = 2455MHz) both at -30dBm per tone. Input IP3 can be improved to
+1dBm with circuit shown in Figure 2.
Note 6: Excluding PC board losses (0.3dB typical at the input of the MAX2644 EV kit).
2
_______________________________________________________________________________________
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
SUPPLY CURRENT vs. RBIAS
6
TA = -40°C
3.0
3.5
4.0
4.5
5.0
12
1.0
1.5
2.0
2.5
3.0
3.5
4.0
2.5
3.5
4.0
TA = -40°C
GAIN (dB)
15
TA = +85°C
TA = +25°C
16
TA = +25°C
15
12
RBIAS = 1.2kΩ
-4
OUTPUT RETURN LOSS
-6
-8
-10
-12
-14
-16
TA = +85°C
14
MAX2644 toc06
18
11
INPUT RETURN LOSS
-18
13
2400
2500
2600
-20
0.5
2700
1.0
1.5
2.0
2.5
3.0
3.5
4.0
2200
REVERSE ISOLATION vs. FREQUENCY
RBIAS = 1.2kΩ
3.5
TA = -40°C
TA = +85°C
2300
2400
2500
FREQUENCY (MHz)
2600
2700
2700
RBIAS = 1.2kΩ
3.0
2.5
2.0
1.5
2.5
2.0
1.5
1.0
1.0
0.5
0.5
-45
-50
2600
3.5
NOSIE FIGURE (dB)
NOSIE FIGURE (dB)
TA = +25°C
2500
NOISE FIGURE vs. TEMPERATURE
4.0
3.0
-30
2400
FREQUENCY (MHz)
NOISE FIGURE vs. FREQUENCY
4.0
MAX2644 toc07
RBIAS = 1.2kΩ
-25
2200
2300
RBIAS (kΩ)
FREQUENCY (MHz)
MAX2644 toc08
2300
MAX2644 toc09
10
5.5
0
-2
REVERSE ISOLATION (dB)
MAX2644 toc04
19
17
16
-40
5.0
INPUT AND OUTPUT RETURN LOSS
vs. FREQUENCY
TA = -40°C
-35
4.5
GAIN vs. RBIAS
13
REVERSE ISOLATION (dB)
3.0
GAIN vs. FREQUENCY
17
GAIN (dB)
13
SUPPLY VOLTAGE (V)
RBIAS = 1.2kΩ
2200
TA = +85°C
TA = +25°C
RBIAS (kΩ)
18
-20
16
SUPPLY VOLTAGE (V)
20
14
17
14
TA = -40°C
0.5
5.5
18
15
MAX2644 toc05
2.5
19
5
1
0
TA = -40°C
19
TA = +25°C
7
3
2
20
TA = +85°C
9
RBIAS = 1.2kΩ
21
GAIN (dB)
8
TA = +25°C
11
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
TA = +85°C
10
GAIN vs. SUPPLY VOLTAGE
22
MAX2644 toc02
MAX2644 toc01
RBIAS = 1.2kΩ
12
4
13
MAX2644 toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
14
0
0
2350
2400
2450
FREQUENCY (MHz)
2500
2550
-40
-15
10
35
60
85
TEMPERATURE (°C)
_______________________________________________________________________________________
3
MAX2644
Typical Operating Characteristics
(PRFIN = -30dBm, ZS = ZL = 50Ω, VCC = +3.0V, fRFIN = 2450MHz, RBIAS = 1.2kΩ, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(PRFIN = -30dBm, ZS = ZL = 50Ω, VCC = +3.0V, fRFIN = 2450MHz, RBIAS = 1.2kΩ, TA = +25°C, unless otherwise noted.)
IIP3 vs. RBIAS
RBIAS = 750Ω
TA = +85°C
-2
-3
-5
IIP3 (dBm)
RBIAS = 1.2kΩ
RBIAS = 3.9kΩ
-10
-13
TA = +25°C
-4
-5
-6
TA = -40°C
-7
TA = +85°C
-12
INPUT P1dB (dBm)
0
-11
MAX2644 toc11
MAX2644 toc10
5
INPUT P1dB vs. RBIAS
-1
MAX2644 toc12
OUTPUT POWER vs. INPUT POWER
10
OUTPUT POWER (dBm)
MAX2644
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
-14
-15
TA = +25°C
-16
-17
TA = -40°C
-15
-8
-18
-9
-20
-30
-25
-20
-15
-10
-5
-19
0.5
0
1.0
INPUT POWER (dBm)
1.5
2.0
3.0
2.5
RBIAS (kΩ)
3.5
4.0
0.5
1.0
1.5
2.0 2.5
RBIAS (kΩ)
3.0
3.5
4.0
Pin Description
PIN
NAME
DESCRIPTION
1
BIAS
Resistor Bias Control. Connect a resistor, RBIAS, from BIAS to ground. RBIAS sets IP3 and supply
current. The current through this pin is approximately 60mV divided by RBIAS (see Applications
Information).
2, 5
GND
Ground. For optimum performance, provide a low-inductance connection to the ground plane.
3
RFIN
Amplifier Input. AC-couple to this pin with a DC blocking capacitor. External matching network is
required for optimum performance.
4
VCC
Supply Voltage. Bypass with a capacitor directly to ground at the supply pin. Refer to VCC Line
Bypassing section for more information.
6
RFOUT
Amplifier Output. AC-coupled internally.
RFOUT
1
BIAS
R1
1.2kΩ
C1
33pF
SMA
L1
3.3nH
6
SMA
U1
2
RFIN
RFOUT
GND
MAX2644
GND
GND
5
VCC
Length = 400mils
3
RFIN
VCC
4
C3
2.2pF
C2
33pF
GAIN: 17dB
IIP3: -3dBm
Figure 1. High Gain Design
4
_______________________________________________________________________________________
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
BIAS
RFOUT
R1
1.2kΩ
C1
33pF
SMA
RFOUT
SMA
U1
2
RFIN
L2
3.9nH
6
MAX2644
1
3
GND
MAX2644
RFIN
GND
VCC
GND
5
4
C2
33pF
C3
15pF
L1
3.3nH
VCC
Length = 400mils
GAIN: 16dB
IIP3: +1dBm
Figure 2. High Linearity Design
BIAS
BIAS
MAX2644
(a)
MAX2644
(b)
Figure 3. Recommended MAX2644 Standby Configurations
Applications Information
Input Matching
Input matching is required for optimum performance.
The MAX2644 requires a simple LC matching network,
as shown in the Typical Operating Circuit. To further
reduce cost and external component count, replace the
external inductor with a microstrip transmission line.
The Typical Operating Circuit shows the recommended
input matching network for the MAX2644 at 2450MHz.
These values are optimized for best simultaneous gain,
noise figure, and return loss performance.
VCC Line Bypassing
Bypassing the V CC line is necessary for optimum
gain/linearity performance. A transmission line and two
capacitors are required, as shown in the schematics in
Figures 1 and 2. The optimum dimensions and positions of the components are as follows: the output
transmission line dimension is 0.532in (length) ✕ 0.012in
(width); the distance from C2 to the IC is 0.352in; and
the distance from C3 to the IC is 0.041in. Please refer
to Figures 1 and 2 for component values.
_______________________________________________________________________________________
5
MAX2644
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
Table 1. MAX2644 Typical Scattering Parameters
(RBIAS = 750Ω, VCC = +3.0V, TA = +25°C.)
FREQ.
(MHz)
S11
MAG
S11 PHASE
(DEGREES)
S21
MAG
S21 PHASE
(DEGREES)
S12
MAG
S12 PHASE
(DEGREES)
S22
MAG
S22 PHASE
(DEGREES)
2200
0.3372
-79.36
5.1940
170.97
0.0414
157.19
0.2818
-73.71
2250
0.3098
-70.09
5.3156
166.79
0.0445
146.70
0.2204
-67.13
2300
0.3283
-57.20
5.4281
159.22
0.0469
130.62
0.1566
-50.26
2350
0.4005
-50.46
5.4175
150.70
0.0441
108.72
0.1480
-3.96
2400
0.4839
-50.28
5.3346
143.93
0.0349
85.67
0.2795
15.12
2450
0.5443
-56.33
5.0687
136.45
0.0233
58.80
0.4179
11.12
2500
0.5758
-60.09
4.9556
132.16
0.0113
27.74
0.5135
3.28
2550
0.5784
-63.61
4.5952
127.68
0.0041
-38.98
0.5622
-2.66
2600
0.5698
-66.56
4.2364
126.58
0.0063
-110.49
0.5986
-7.45
2650
0.5600
-68.51
4.1376
126.51
0.0103
-128.93
0.6208
-10.43
2700
0.5533
-69.86
4.0729
120.60
0.0133
-140.21
0.6425
-12.93
Table 2. MAX2644 Typical Scattering Parameters
(RBIAS = 1.2kΩ, VCC = +3.0V, TA = +25°C.)
FREQ.
(MHz)
S11
MAG
S11 PHASE
(DEGREES)
S21
MAG
S21 PHASE
(DEGREES)
S12
MAG
S12 PHASE
(DEGREES)
S22
MAG
S22 PHASE
(DEGREES)
2200
0.3482
-67.06
5.2390
-177.33
0.0402
161.53
0.2873
-76.58
2250
0.3121
-58.60
5.3790
178.72
0.0435
151.97
0.2305
-69.42
2300
0.3051
-43.64
5.5982
173.43
0.0452
136.90
0.1735
-54.22
2350
0.3693
-30.34
5.8137
166.48
0.0427
116.57
0.1582
-16.42
2400
0.4769
-29.48
5.8063
158.29
0.0341
95.13
0.2687
6.52
2450
0.5619
-35.54
5.6624
150.06
0.0236
68.36
0.4043
5.00
2500
0.5948
-42.64
5.3015
142.37
0.0117
41.34
0.5030
-2.19
2550
0.5939
-47.58
4.7813
136.67
0.0034
-13.74
0.5602
-8.04
2600
0.5825
-50.94
4.3271
134.58
0.0056
-104.09
0.5952
-12.76
2650
0.5708
-53.14
4.1961
133.48
0.0096
-124.80
0.6215
-15.97
2700
0.5604
-54.35
4.1068
128.01
0.0125
-134.75
0.6434
-18.83
Standby
Standby mode is achieved by disconnecting BIAS as
shown in Figure 1. Avoid capacitance at the BIAS pin
by connecting the bias resistor from BIAS to the switch.
Layout Issues
A properly designed PC board is essential to any
RF/microwave circuit. Use controlled impedance lines
on all high-frequency inputs and outputs. Bypass with
decoupling capacitors located close to the device VCC
6
pin. For long VCC lines, it may be necessary to add
additional decoupling capacitors. These additional
capacitors can be located farther away from the device
package. Proper grounding of the GND pins is essential. If the PC board uses a topside RF ground, connect
it directly to all GND pins. For a board where the
ground plane is not on the component layer, the best
technique is to connect the GND pins to the board with
a plated through-hole located close to the package.
_______________________________________________________________________________________
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
MAX2644
Table 3. MAX2644 Typical Scattering Parameters
(RBIAS = 3.9kΩ, VCC = +3.0V, TA = +25°C.)
FREQ.
(MHz)
S11
MAG
S11 PHASE
(DEGREES)
S21
MAG
S21 PHASE
(DEGREES)
S12
MAG
S12 PHASE
(DEGREES)
S22
MAG
S22 PHASE
(DEGREES)
2200
0.4894
-75.32
3.7368
-173.73
0.0348
156.35
0.2729
-62.97
2250
0.4566
-72.73
3.7718
-177.51
0.0363
147.30
0.2459
-53.68
2300
0.4335
-68.17
3.8855
177.43
0.0369
132.32
0.2211
-41.12
2350
0.4343
-61.46
3.9783
171.34
0.0344
116.21
0.2177
-21.15
2400
0.4695
-57.00
4.0230
165.15
0.0272
95.31
0.2823
-2.41
2450
0.5156
-57.52
4.0087
157.68
0.0179
70.07
0.3924
1.25
2500
0.5403
-61.04
3.8380
149.58
0.0079
42.40
0.4849
-2.71
2550
0.5423
-63.93
3.5140
143.30
0.0018
-46.47
0.5476
-7.30
2600
0.5361
-66.30
3.2048
140.25
0.0055
-112.91
0.5881
-11.35
2650
0.5280
-68.08
3.1204
138.55
0.0100
-132.25
0.6170
-14.57
2700
0.5217
-69.29
3.0860
132.16
0.0121
-133.97
0.6418
-17.44
Table 4. MAX2644 Typical Noise
Parameters at VCC = +3.0V, TA = +25°C,
RBIAS = 750Ω
Table 5. MAX2644 Typical Noise
Parameters at VCC = +3.0V, TA = +25°C,
RBIAS = 1.2kΩ
FREQUENCY
(MHz)
FMIN
(dB)
Γopt
Γopt
ANGLE
RN
(Ω)
FREQUENCY
(MHz)
FMIN
(dB)
Γopt
Γopt
ANGLE
RN
(Ω)
2400
1.725
0.361
66.13
24.38
2400
1.570
0.409
69.84
21.77
2450
1.747
0.360
66.93
24.76
2450
1.589
0.408
70.63
21.94
2500
1.769
0.358
67.72
25.14
2500
1.609
0.406
71.63
22.42
Table 6. MAX2644 Typical Noise
Parameters at VCC = +3.0V, TA = +25°C,
RBIAS = 3.9kΩ
FREQUENCY
(MHz)
FMIN
(dB)
Γopt
Γopt
ANGLE
RN
(Ω)
2400
1.497
0.510
86.55
20.58
2450
1.517
0.507
86.50
20.90
2500
1.538
0.504
88.18
21.25
Chip Information
TRANSISTOR COUNT: 87
_______________________________________________________________________________________
7
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
SC70, 6L.EPS
MAX2644
2.4GHz SiGe,
High IP3 Low-Noise Amplifier
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.