MOTOROLA Freescale Semiconductor, Inc. Order this document by MC145506/D SEMICONDUCTOR TECHNICAL DATA Freescale Semiconductor, Inc... Advance Information PCM Codec-Filter Mono-Circuit The MC145506, MC145507, and MC145508 are per channel codec–filter PCM mono–circuits. These devices perform the voice digitization and reconstruction, as well as the band limiting and smoothing required for PCM systems. These devices have HCMOS compatible digital outputs and otherwise supplement the MC145500 – MC145505 series of PCM codec–filters. The MC145506, MC145507, and MC145508 are functionally similar to the MC145502, MC145503, and MC145505, respectively. They are designed to operate in both synchronous and asynchronous applications and contain an on–chip precision reference voltage. The MC145506 is offered in a 22–pin package and has the capability of selecting from three peak overload voltages (2.5 V, 3.15 V, and 3.78 V). The MC145507 and MC145508 offer versatility and low cost in 16–pin DIP and wide body SOIC packages. Most of the features of these devices can be made available in a lower pin count package tailored to a specific user’s application. Contact the factory for further details. These devices maintain compatibility with Motorola’s family of MC3419/ MC33120 SLIC products. The MC145500 family of PCM codec–filter mono–circuits utilize CMOS due to its reliable low–power performance and proven capability for complex analog/digital VLSI functions. MC145506 MC145507 MC145508 16 1 P SUFFIX PLASTIC DIP CASE 648 16 1 DW SUFFIX SO PACKAGE CASE 751G MC145507/08 MC145506 (22–Pin Package, HCMOS Output Version of MC145502) • Selectable Peak Overload Voltages (2.5 V, 3.15 V, 3.78 V) • Push–Pull Analog Output with Gain Adjust • 64 kHz to 4.1 MHz Transmit and/or Receive Data Clock Rate • All the Features of the MC145507 Listed Below MC145507 (16–Pin Package, HCMOS Output Version of MC145503) • Transmit Bandpass and Receive Low–Pass Filters on Chip • Pin Selectable Mu/A Law Companding with Corresponding Data Format • On–Chip Precision Reference Voltage (3.15 V) • Power Dissipation of 50 mW, Power Down of 0.1 mW at ±5 V • Three Terminal Transmit Input Operational Amplifier • Automatic Prescaler Accepts 128 kHz, 1.536 MHz, 1.544 MHz, 2.048 MHz, and 2.56 MHz for Internal Sequencing • Separate Transmit and Receive Data Clocks 22 1 P SUFFIX PLASTIC DIP CASE 708 MC145506 MC145508 (16–Pin Package, HCMOS Output Version of MC145505) Same as MC145507 Except: • Common 64 kHz to 4.1 MHz Transmit/Receive Data Clock • Separate CCI Pin with Automatic Prescaler Accepts 128 kHz, 1.536 MHz, 1.544 MHz, 2.048 MHz, and 2.56 MHz for Internal Sequencing This document contains information on a new product. Specifications and information herein are subject to change without notice. REV 0 2/00 Motorola, Inc. 2000 MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 1 Freescale Semiconductor, Inc. MC145506/07/08 PCM CODEC–FILTER MONO–CIRCUIT BLOCK DIAGRAM RDD 1 RxO D/A FREQUENCY Rx RECEIVE SHIFT REGISTER RCE ÷ 1, 12, 16, 20 CCI PRESCALER CCI RDC RxG Rx – VDD SHARED DAC 400 µA RxO + VDD VSS VAG 2.5 V REF + MSI Freescale Semiconductor, Inc... – VSS Vref RSI TxI A/D +Tx + NOTES: VLS TRANSMIT SHIFT REGISTER TDD PDI RSI CIRCUITRY – –Tx SEQUENCE AND CONTROL FREQUENCY TDE TDC FREQUENCY Controlled by VLS. Rx ≈ 100 kΩ (internal resistors). PIN ASSIGNMENTS (Drawings Do Not Reflect Relative Size) MC145506P MC145507P MC145508P Vref 1 22 RSI VAG 1 16 VDD VAG 1 16 VDD VAG 2 21 VDD RxO 2 15 RDD RxO 2 15 RDD RxO 3 20 RDD +Tx 3 14 RCE +Tx 3 14 RCE RxG 4 19 RCE TxI 4 13 RDC TxI 4 13 DC RxO 5 18 RDC –Tx 5 12 TDC –Tx 5 12 CCI +Tx 6 17 TDC Mu/A 6 11 TDD Mu/A 6 11 TDD TxI 7 16 CCI PDI 7 10 TDE PDI 7 10 TDE –Tx 8 15 TDD VSS 8 9 VLS VSS 8 9 VLS Mu/A 9 14 TDE PDI 10 13 MSI VSS 11 12 VLS MC145507DW MC145508DW VAG 1 16 VDD VAG 1 16 VDD RxO 2 15 RDD RxO 2 15 RDD +Tx 3 14 RCE +Tx 3 14 RCE TxI 4 13 RDC TxI 4 13 DC –Tx 5 12 TDC –Tx 5 12 CCI Mu/A 6 11 TDD Mu/A 6 11 TDD PDI 7 10 TDE PDI 7 10 TDE VSS 8 9 VLS VSS 8 9 VLS MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 2 MOTOROLA Freescale Semiconductor, Inc. ABSOLUTE MAXIMUM RATINGS (Voltage Referenced to VSS) Rating Symbol Value Unit VDD – VSS –0.5 to 13 V Voltage, Any Pin to VSS V –0.5 to VDD + 0.5 V DC Drain Per Pin (Excluding VDD, VSS) I 10 mA TA –40 to 85 °C Tstg –85 to 150 °C DC Supply Voltage Operating Temperature Range Storage Temperature Range This device contains circuitry to protect against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high–impedance circuit. For proper operation, it is recommended that Vin and Vout be constrained to the range VSS ≤ (Vin or Vout) ≤ VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., V SS, VDD, VLS, or VAG). RECOMMENDED OPERATING CONDITIONS (TA = –40° to 85°C) Freescale Semiconductor, Inc... Characteristic Min Typ Max 4.75 5.0 6.3 8.5 7.0 9.5 4.75 — — — — 12.6 12.6 12.6 12.6 Power Dissipation CMOS Logic Mode (VDD to VSS = 10 V, VLS = VDD) HCMOS Logic Mode (VDD = 5 V, VSS = –5 V, VLS = VAG = 0 V) — — 40 50 70 90 Power Down Dissipation — 0.1 1.0 mW Frame Rate Transmit and Receive 7.5 8.0 8.5 kHz CCI Clock Rate (TDC Clock Rate for MC145507) MC145506, MC145508 Must Use One of These Frequencies ±2%, Relative to MSI Frequency of 8 kHz — — — — — 128 1536 1544 2048 2560 — — — — — kHz Data Rate for MC145506, MC145508 64 — 4096 kHz — — — — — — — 3.15 3.78 3.15 2.5 1.51 x Vref 1.26 x Vref Vref — — — — — — — Symbol Min Max VIL VIH VIL VIH — 0.7 x VDD — VLS + 2.0 V 0.3 x VDD — VLS + 0.8 V — DC Supply Voltage Dual Supplies: VDD = –VSS (VAG = VLS = 0 V) Single Supply: VDD to VSS (VAG is an Output, VLS = VDD or VSS) MC145506, MC145507, MC145508 Using Internal 3.15 V Reference MC145506 Using Internal 2.5 V Reference MC145506 Using Internal 3.78 V Reference MC145506 Using External 1.5 V Reference, Referenced to VAG Full Scale Analog Input and Output Level MC145507, MC145508 MC145506 (Vref = VSS) MC145506 Using an External Reference Voltage Applied at Vref Pin Unit V mW VP RSI = VDD RSI = VSS RSI = VAG RSI = VDD RSI = VSS RSI = VAG DIGITAL LEVELS (VSS to VDD = 4.75 V to 12.6 V, TA = –40° to 85°C) Characteristic Input Voltage Levels (TDE, TDC, RCE, RDC, RDD, DC, MSI, CCI, PDI) CMOS Mode (VLS = VDD, VSS is Digital Ground) HCMOS Mode (VLS ≤ VDD – 4.0 V, VLS is Digital Ground) V “0” “1” “0” “1” Output Current for TDD (Transmit Digital Data) CMOS Mode (VLS = VDD, VSS = 0 V and is Digital Ground) (VDD = 5 V, Vout = 0.4 V) (VDD = 10 V, Vout = 0.5 V) (VDD = 5 V, Vout = 4.5 V) (VDD = 10 V, Vout = 9.5 V) HCMOS Mode (VLS ≤ VDD – 4.75 V, VLS = 0 V and is Digital Ground) (VOL = 0.4 V) (VOH = VDD – 0.5 V) MOTOROLA Unit mA IOL IOH IOL IOH 1.6 1.6 –1.6 –1.6 1.6 –1.6 — — — — — — MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 3 Freescale Semiconductor, Inc. ANALOG TRANSMISSION PERFORMANCE (VDD = 5 V ± 5%, VSS = –5 V ± 5%, VLS = VAG = 0 V, Vref = RSI = VSS (Internal 3.15 V Reference), 0 dBm0 = 1.546 Vrms = 6 dBm @ 600 Ω, TA = –40° to 85°C, TDC = RDC = CCI, TDE = RCE = MSI, Unless Otherwise Noted) End–to–End D/A Characteristic Min Max Min Max Min Max Unit Absolute Gain (0 dBm0 @ 1.02 kHz, TA = 25°C, VDD = 5 V, VSS = –5 V) — — –0.30 0.30 –0.30 0.30 dB Absolute Gain Variation with Temperature 0° to 70°C — — — ±0.03 — ±0.03 dB Absolute Gain Variation with Temperature –40° to 85°C — — — ±0.1 — ±0.1 dB Absolute Gain Variation with Power Supply (VDD = 5 V, VSS = –5 V, 5%) — — — ±0.02 — ±0.02 dB –0.4 –0.8 –1.6 0.4 0.8 1.6 –0.2 –0.4 –0.8 0.2 0.4 0.8 –0.2 –0.4 –0.8 0.2 0.4 0.8 dB — — — — — — –0.25 –0.30 –0.45 0.25 0.30 0.45 –0.25 –0.30 –0.45 0.25 0.30 0.45 0 to –30 dBm0 –40 dBm0 –45 dBm0 35 29 24 — — — 36 29 24 — — — 36 30 25 — — — dBC –3 dBm0 –6 to –27 dBm0 –34 dBm0 –40 dBm0 –55 dBm0 27.5 35 33.1 28.2 13.2 — — — — — 28 35.5 33.5 28.5 13.5 — — — — — 28.5 36 34.2 30.0 15.0 — — — — — dB — — 15 –69 — — 15 –69 — — 9 –78 dBrnC0 dBm0p — –0.3 –1.6 — — –23 0.3 0 –28 –60 — –0.15 –0.8 — — –23 0.15 0 –14 –32 — –0.15 –0.8 — — 0.15 0.15 0 –14 –30 dB — — — –43 — –43 dBm0 Out–of–Band Spurious at RxO (300 – 3400 Hz @ 0 dBm0 In) 4600 to 7600 Hz 7600 to 8400 Hz 8400 to 100,000 Hz — — — –30 –40 –30 — — — — — — — — — –30 –40 –30 Idle Channel Noise Selective @ 8 kHz, Input = VAG, 30 Hz Bandwidth — –70 — — — –70 Gain vs Level Tone (Relative to –10 dBm0, 1.02 kHz) Freescale Semiconductor, Inc... A/D 3 to –40 dBm0 –40 to –50 dBm0 –50 to –55 dBm0 Gain vs Level Pseudo Noise (A–Law Relative to –10 dBm0) CCITT G.714 –10 to –40 dBm0 –40 to –50 dBm0 –50 to –55 dBm0 Total Distortion – 1.02 kHz Tone (C–Message) Total Distortion With Pseudo Noise (A–Law) CCITT G.714 Idle Channel Noise (For End–End and A/D, See Note 1) (Mu–Law, C–Message Weighted) (A–Law, Psophometric Weighted) Frequency Response (Relative to 1.02 kHz @ 0 dBm0) 15 to 60 Hz 300 to 3000 Hz 3400 Hz 4000 Hz ≥4600 Hz Inband Spurious (1.02 kHz @ 0 dBm0, Transmit and RxO) dB 300 to 3000 Hz dB dBm0 Absolute Delay @ 1020 Hz (TDC = 2.048 MHz, TDE = 8 kHz) µs Group Delay Referenced to 1600 Hz (TDC = 2048 kHz, TDE = 8 kHz) µs 500 to 600 Hz 600 to 800 Hz 800 to 1000 Hz 1000 to 1600 Hz 1600 to 2600 Hz 2600 to 2800 Hz 2800 to 3000 Hz Crosstalk of 1020 Hz @ 0 dBm0 From A/D or D/A (Note 2) — — — –75 — –80 dB Intermodulation Distortion of Two Frequencies of Amplitudes –4 to –21 dBm0 from the Range 300 to 3400 Hz — — — –41 — –41 dB NOTES: 1. Extrapolated from a 1020 Hz @ –50 dBm0 distortion measurement to correct for encoder enhancement. 2. Selectively measured while the A/D is stimulated with 2667 Hz @ –50 dBm0. MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 4 MOTOROLA Freescale Semiconductor, Inc. ANALOG ELECTRICAL CHARACTERISTICS (VDD = –VSS = 5 V to 6 V ±5%, TA = –40° to 85°C) Symbol Min Typ Max Unit Input Current +Tx, –Tx Iin — ±0.01 ±0.2 µA AC Input Impedance to VAG (1 kHz) +Tx, –Tx Zin 5 10 — MΩ Input Capacitance +Tx, –Tx — — 10 pF — < ±30 — mV Characteristic Input Offset Voltage of Txl Op Amp Input Common Mode Voltage Range +Tx, –Tx VICR VSS + 1.0 — VDD – 2.0 V Input Common Mode Rejection Ratio +Tx, –Tx CMRR — 70 — dB Txl Unity Gain Bandwidth RL ≥ 10 kΩ BWp — 1000 — kHz Txl Open Loop Gain RL ≥ 10 kΩ AVOL — 75 — dB Equivalent Input Noise (C–Message) Between +Tx and –Tx, at Txl — –20 — dBrnC0 Output Load Capacitance for Txl Op Amp 0 — 100 pF VSS + 0.8 VSS + 1.5 — — VDD – 1.0 VDD – 1.5 ±5.5 — — mA — 3 — Ω 0 — 200 pF — — — — ±100 ±150 mV Internal Gainsetting Resistors for RxG to RxO and RxO 62 100 225 kΩ External Reference Voltage Applied to Vref (Referenced to VAG) 0.5 — VDD – 1.0 V Vref Input Current — — 20 µA VAG Output Bias Voltage — 0.53 VDD + 0.47 VSS — V 0.4 10.0 — — 0.8 — mA Output Leakage Current During Power Down for the Txl Op Amp, VAG, RxO, and RxO — — ±30 µA Positive Power Supply Rejection Ratio, 0 – 100 kHz @ 250 mV, C–Message Weighting Transmit Receive 45 55 50 65 — — dBC Negative Power Supply Rejection Ratio, 0 – 100 kHz @ 250 mV, C–Message Weighting Transmit Receive 50 50 55 60 — — dBC Freescale Semiconductor, Inc... Output Voltage Range Txl Op Amp, RxO or RxO Vout RL = 10 kΩ to VAG RL = 600 Ω to VAG Output Current Txl, RxO, RxO VSS + 1.5 V ≤ Vout ≤ VDD – 1.5 V Output Impedance RxO, RxO* 0 to 3.4 kHz Zout Output Load Capacitance for RxO and RxO* Output dc Offset Voltage Referenced to VAG Pin VAG Output Current RxO RxO* Source Sink IVAG V * Assumes that RxG is not connected for gain modifications to RxO. MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 5 Freescale Semiconductor, Inc. MODE CONTROL LOGIC (VSS to VDD = 4.75 V to 12.6 V, TA = –40° to 85°C) Characteristic Min Typ Max Unit VSS — VDD – 4.0 V VDD – 0.5 — VDD V Mu–Law Mode Sign Magnitude Mode A–Law Mode VDD – 0.5 VAG – 0.5 VSS — — — VDD VAG + 0.5 VSS + 0.5 3.78 V Mode 2.5 V Mode 3.15 V Mode VDD – 0.5 VAG – 0.5 VSS — — — VDD VAG + 0.5 VSS + 0.5 Vref Voltage for Internal or External Reference (MC145506 Only) Internal Reference Mode External Reference Mode VSS VAG + 0.5 — — VSS + 0.5 VDD – 1.0 — 128 — VLS Voltage for HCMOS Mode (HCMOS Logic Levels Referenced to VLS) VLS Voltage for CMOS Mode (CMOS Logic Levels of VSS to VDD) Mu/A Select Voltage V RSI Voltage for Reference Select Input (MC145506) Freescale Semiconductor, Inc... Analog Test Mode Selection Frequency, MS = CCI (MC145506 Only) See Pin Description; Test Modes V V kHz SWITCHING CHARACTERISTICS (VSS to VDD = 9.5 V to 12.6 V, TA = –40° to 85°C, CL = 150 pF, CMOS or HCMOS Mode) Symbol Min Typ Max Unit TDD tTLH tTHL — — 30 30 80 80 ns TDE, TDC, RCE, RDC, DC, MSI, CCI tTLH tTHL — — — — 4 4 µs tw 100 — — ns Characteristic Output Rise Time Output Fall Time Input Rise Time Input Fall Time Pulse Width TDE Low, TDC, RCE, RDC, DC, MSI, CCI Data Clock Pulse Frequency TDC, RDC, DC CCI Clock Pulse Frequency (MSI = 8 kHz) This Pin Will Accept One of These Discrete Clock Frequencies and Will Compensate to Produce Internal Sequencing Propagation Delay Time TDE Rising to TDD Low Impedance TDE Falling to TDD High Impedance TDC Rising Edge to TDD Data, During TDE High TDE Rising Edge to TDD Data, During TDC High fCL 64 — 4096 kHz fCL1 fCL2 fCL3 fCL4 fCL5 — — — — — 128 1536 1544 2048 2560 — — — — — kHz tP1 — — — — — — — — 90 90 — — 90 90 90 90 180 150 55 40 180 150 180 150 ns HCMOS CMOS HCMOS CMOS HCMOS CMOS HCMOS CMOS tP2 tP3 tP4 TDC Falling Edge to TDE Rising Edge Setup Time tsu1 20 — — ns TDE Rising Edge to TDC Falling Edge Setup Time tsu2 100 — — ns TDE Falling Edge to TDC Rising Edge to Preserve the Next TDD Data tsu8 20 — — ns RDC Falling Edge to RCE Rising Edge Setup Time tsu3 20 — — ns RCE Rising Edge to RDC Falling Edge Setup Time tsu4 100 — — ns RDD Valid to RDC Falling Edge Setup Time tsu5 60 — — ns CCI Falling Edge to MSI Rising Edge Setup Time tsu6 20 — — ns MSI Rising Edge to CCI Falling Edge Setup Time tsu7 100 — — ns th 100 — — ns RDD Hold Time from RDC Falling Edge TDE, TDC, RCE, RDC, RDD, DC, MSI, CCI Input Capacitance — — 10 pF TDE,TDC, RCE, RDC, RDD, DC, MSI, CCI Input Current — ±0.01 ±0.2 µA TDD Capacitance During High Impedance (TDE Low) — 12 15 pF TDD Input Current During High Impedance (TDE Low) — ±0.1 ±10.0 µA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 6 MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... DEVICE DESCRIPTIONS A codec–filter is a device which is used for digitizing and reconstructing the human voice. These devices were developed primarily for the telephone network to facilitate voice switching and transmission. Once the voice is digitized, it may be switched by digital switching methods or transmitted long distance (T1, microwave, satellites, etc.) without degradation. The name codec is an acronym from “coder” for the A/D used to digitize voice, and “decoder” for the D/A used for reconstructing voice. A codec is a single device that does both the A/D and D/A conversions. To digitize intelligible voice requires a signal to distortion of about 30 dB for a dynamic range of about 40 dB. This may be accomplished with a linear 13–bit A/D and D/A, but will far exceed the required signal to distortion at amplitudes greater than 40 dB below the peak amplitude. This excess performance is at the expense of data per sample. Two methods of data reduction are implemented by compressing the 13–bit linear scheme to companded 8–bit schemes. These companding schemes follow a segmented or “piecewise–linear” curve formatted as a sign bit, 3 chord bits, and 4 step bits. For a given chord, all 16 of the steps have the same voltage weighting. As the voltage of the analog input increases, the 4 step bits increment and carry to the 3 chord bits which increment. With the chord bits incremented, the step bits double their voltage weighting. This results in an effective resolution of 6 bits (sign + chord + 4 step bits) across a 42 dB dynamic range (7 chords above 0, by 6 dB per chord). There are two companding schemes used; Mu–255 Law specifically in North America, and A–Law specifically in Europe. These companding schemes are accepted world wide. The tables show the linear quantization levels to PCM words for the two companding schemes. In a sampling environment, Nyquist theory says that to properly sample a continuous signal, it must be sampled at a frequency higher than twice the signal’s highest frequency component. Voice contains spectral energy above 3 kHz, but its absence is not detrimental to intelligibility. To reduce the digital data rate, which is proportional to the sampling rate, a sample rate of 8 kHz was adopted, consistent with a bandwidth of 3 kHz. This sampling requires a low–pass filter to limit the high frequency energy above 3 kHz from distorting the inband signal. The telephone line is also subject to 50/60 Hz power line coupling which must be attenuated from the signal by a high–pass filter before the A/D converter. The D/A process reconstructs a staircase version of the desired inband signal which has spectral images of the inband signal modulated about the sample frequency and its harmonics. These spectral images are called aliasing components which need to be attenuated to obtain the desired signal. The low–pass filter used to attenuate these aliasing components is typically called a reconstruction or smoothing filter. The MC145500 series PCM codec–filters have the codec, both presampling and reconstruction filters, a precision voltage reference on chip, and require no external components. There are three distinct versions of the Motorola MC145500 series with HCMOS compatible outputs. MC145506 The MC145506 PCM codec–filter is the full–featured 22–pin device. It is intended for use in applications requiring MOTOROLA maximum flexibility. The MC145506 contains all the features of the MC145507 and MC145508. The MC145506 is intended for bit interleaved or byte interleaved applications with data clock frequencies which are nonstandard or time varying. One of the five standard frequencies (listed below) is applied to the CCI input, and the data clock inputs can be any frequency between 64 kHz and 4.096 MHz. The Vref pin allows for use of an external shared reference or selection of the internal reference. The RxG pin accommodates gain adjustments for the inverted analog output. All three pins of the input gainsetting operational amplifier are present which provide maximum flexibility for the analog interface. MC145507 The MC145507 PCM mono–circuit is intended for standard byte interleaved synchronous or asynchronous applications. TDC can be one of five discrete frequencies. These are 128 kHz (40% to 60% duty cycle), 1.536 MHz, 1.544 MHz, 2.048 MHz, or 2.56 MHz. (For other data clock frequencies, see MC145506 or MC145508.) The internal reference is set for 3.15 V peak full scale, and the full scale input level at TxI and output level at RxO is 6.3 Vp–p. This is the 3 dBm0 level of the PCM codec–filter. The +Tx and –Tx inputs provide maximum flexibility for analog interface. All other functions are described in the pin description. MC145508 The MC145508 PCM mono–circuit is intended for byte interleaved synchronous applications. The MC145508 has all the features of the MC145507 but internally connects TDC and RDC (see pin description) to the DC pin. One of the five standard frequencies (listed above) should be applied to CCI. The data clock input (DC) can be any frequency between 64 kHz and 4.069 MHz. PIN DESCRIPTIONS DIGITAL VLS Logic Level Select Input and HCMOS Digital Ground VLS controls the logic levels and digital ground reference for all digital inputs and the digital output. These devices can operate with logic levels from full supply (VSS to VDD) or with TTL logic levels using VLS as digital ground. For VLS = VDD, all I/O is full supply (VSS to VDD swing) with CMOS switch points. For VSS < VLS < (VDD – 4 V), all inputs are TTL compatible with VLS being the digital ground while TDD outputs HCMOS levels from VLS to VDD. The pins controlled by VLS are inputs MSI, CCI, TDE, TDC, RCE, RDC, RDD, PDI, and output TDD. MSI Master Synchronization Input MSI is used for determining the sample rate of the transmit side and as a time base for selecting the internal prescale divider for the convert clock input (CCI) pin. The MSI pin should be tied to an 8 kHz clock which may be a frame sync or system sync signal. MSI has no relation to transmit or receive data timing, except for determining the internal transmit strobe as described under the TDE pin description. MSI should be derived from the transmit timing in asynchronous applications. In many applications, MSI can be tied to TDE. (MSI is tied internally to TDE in the MC145507/08.) MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 7 Freescale Semiconductor, Inc. CCI Convert Clock Input CCI is designed to accept five discrete clock frequencies. These are 128 kHz, 1.536 MHz, 1.544 MHz, 2.048 MHz, or 2.56 MHz. The frequency at this input is compared with MSI and prescale divided to produce the internal sequencing clock at 128 kHz (or 16 times the sampling rate). The duty cycle of CCI is dictated by the minimum pulse width except for 128 kHz, which is used directly for internal sequencing and must have a 40% to 60% duty cycle. In asynchronous applications, CCI should be derived from transmit timing. (CCI is tied internally to TDC in the MC145507.) Freescale Semiconductor, Inc... TDC Transmit Data Clock Input TDC can be any frequency from 64 kHz to 4.096 MHz, and is often tied to CCI if the data rate is equal to one of the five discrete frequencies. This clock is the shift clock for the transmit shift register and its rising edges produce successive data bits at TDD. TDE should be derived from this clock. (TDC and RDC are tied together internally in the MC145508 and are called DC.) TDE Transmit Data Enable Input TDE serves three major functions. The first TDE rising edge following an MSI rising edge, generates the internal transmit strobe which initiates an A/D conversion. The internal transmit strobe also transfers a new PCM data word into the transmit shift register (sign bit first) ready to be output at TDD. The TDE pin is the high–impedance control for the transmit digital data (TDD) output. As long as this pin is high, the TDD output stays low impedance. This pin also enables the output shift register for clocking out the 8–bit serial PCM word. The logical AND of the TDE pin with the TDC pin, clocks out a new data bit at TDD. TDE should be held high for eight consecutive TDC cycles to clock out a complete PCM word for byte interleaved applications. The transmit shift register feeds back on itself to allow multiple reads of the transmit data. If the PCM word is clocked out once per frame in a byte interleaved system, the MSI pin function is transparent and may be connected to TDE. The TDE pin may be cycled during a PCM word for bit interleaved applications. TDE controls both the high–impedance state of the TDD output and the internal shift clock. TDE must fall before TDC rises (tsu8) to ensure integrity of the next data bit. There must be at least two TDC falling edges between the last TDE rising edge of one frame and the first TDE rising edge of the next frame. MSI must be available separate from TDE for bit interleaved applications. TDD Transmit Digital Data Output The output levels at this pin are controlled by the VLS pin. For VLS connected to VDD, the output levels are from VSS to VDD. For a voltage of VLS between VDD – 4 V and VSS, the output levels are HCMOS compatible with VLS being the digital ground supply and VDD being the positive logic supply. The TDD pin is a three–state output controlled by the TDE pin. The timing of this pin is controlled by TDC and TDE. The data format (Mu–Law, A–Law, or sign magnitude) is controlled by the Mu/A pin. RDC Receive Data Clock Input RDC can be any frequency from 64 kHz to 4.096 MHz. This pin is often tied to the TDC pin for applications that can use a common clock for both transmit and receive data transfers. The receive shift register is controlled by the receive clock enable (RCE) pin to clock data into the receive digital data (RDD) pin on falling RDC edges. These three signals can be asynchronous with all other digital pins. The RDC input is internally tied to the TDC input on the MC145508 and called DC. RCE Receive Clock Enable Input The rising edge of RCE should identify the sign bit of a receive PCM word on RDD. The next falling edge of RDC, after a rising RCE, loads the first bit of the PCM word into the receive register. The next seven falling edges enter the remainder of the PCM word. On the ninth rising edge, the receive PCM word is transferred to the receive buffer register and the A/D sequence is interrupted to commence the decode process. In asynchronous applications with an 8 kHz transmit sample rate, the receive sample rate should be between 7.5 kHz and 8.5 kHz. Two receive PCM words may be decoded and analog summed each transmit frame to allow on–chip conferencing. The two PCM words should be clocked in as two single PCM words, a minimum of 31.25 µs apart, with a receive data clock of 512 kHz or faster. RDD Receive Digital Data Input RDD is the receive digital data input. The timing for this pin is controlled by RDC and RCE. The data format is determined by the Mu/A pin. Mu/A Mu/A Select This pin selects the companding law and the data format at TDD and RDD. Mu/A = VDD; Mu–255 Companding D3 Data Format with Zero Code Suppress Mu/A = VAG; Mu–255 Companding with Sign Magnitude Data Format Mu/A = VSS; A–Law Companding with CCITT Data Format Bit Inversions Code Sign/ Magnitude + Full Scale + Zero – Zero – Full Scale 1111 1111 1000 0000 0000 0000 0111 1111 SIGN BIT 0 1000 1111 0111 0000 CHORD BITS 1 2 A–Law (CCITT) Mu–Law 0000 1111 1111 0010 1010 1101 0101 0010 1010 0101 0101 1010 STEP BITS 3 4 5 6 7 NOTE: Starting from sign magnitude, to change format: To Mu–Law — MSB is unchanged (sign) Invert remaining 7 bits If code is 0000 0000, change to 0000 0010 (for zero code suppression) MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 8 MOTOROLA Freescale Semiconductor, Inc. reference voltage gain selection circuitry associated with RSI must be considered to arrive at the desired codec–filter gain. Internal Mode — In the internal reference mode (Vref = VSS), an internal 2.5 V reference supplies the reference voltage for the RSI circuitry. The Vref pin is functionally connected to VSS for the MC145507 and MC145508 pinouts. To A–Law — MSB is unchanged (sign) Invert odd numbered bits Ignore zero code suppression PDI Power Down Input The power down input disables the bias circuitry and gates off all clock inputs. This puts the VAG, Txl, RxO, RxO, and TDD outputs into a high–impedance state. The power dissipation is reduced to 0.1 mW when PDI is a low logic level. The circuit operates normally with PDI = VDD or with a logic high as defined by connection at VLS. TDD will not come out of high impedance for two MSI cycles after PDI goes high. Freescale Semiconductor, Inc... DC Data Clock Input In the MC145508, TDC and RDC are internally connected to DCLK. ANALOG VAG Analog Ground Input/Output Pin VAG is the analog ground power supply input/output. All analog signals into and out of the device use this as their ground reference. Each version of the MC145500 PCM codec–filter family can provide its own analog ground supply internally. The dc voltage of this internal supply is 6% positive of the midway between VDD and VSS. This supply can sink more than 8 mA but has a current source limited to 400 µA. The output of this supply is internally connected to the analog ground input of the part. The node where this supply and the analog ground are connected is brought out to the VAG pin. In symmetric dual supply systems (±5, ±6, etc.), VAG may be externally tied to the system analog ground supply. When RxO or RxO drive low–impedance loads tied to VAG, a pull– up resistor to VDD will be required to boost the source current capability if VAG is not tied to the supply ground. All analog signals for the part are referenced to VAG, including noise; therefore, decoupling capacitors (0.1 µF) should be used from VDD to VAG and VSS to VAG. Vref Positive Voltage Reference Input (MC145506 Only) The Vref pin allows an external reference voltage to be used for the A/D and D/A conversions. If Vref is tied to VSS, the internal reference is selected. If Vref > VAG, then the external mode is selected and the voltage applied to Vref is used for generating the internal converter reference voltage. In either internal or external reference mode, the actual voltage used for conversion is multiplied by the ratio selected by the RSI pin. The RSI pin circuitry is explained under its pin description below. Both the internal and external references are inverted within the PCM codec–filter for negative input voltages such that only one reference is required. External Mode — In the external reference mode (Vref > VAG), a 2.5 V reference like the MC1403 may be connected from Vref to VAG. A single external reference may be shared by tying together a number of Vref pins and VAG pins from different codec–filters. In special applications, the external reference voltage may be between 0.5 and 5 V. However, the MOTOROLA RSI Reference Select Input (MC145506 Only) The RSI input allows the selection of three different overload or full–scale A/D and D/A converter reference voltages independent of the internal or external reference mode. The RSI pin is a digital input that senses three different logic states: V SS, VAG, and V DD. For RSI = VAG, the reference voltage is used directly for the converters. The internal reference is 2.5 V. For RSI = V SS, the reference voltage is multiplied by the ratio of 1.26, which results in an internal converter reference of 3.15 V. For RSI = VDD, the reference voltage is multiplied by 1.51, which results in an internal converter reference of 3.78 V. The device requires a minimum of 1.0 V of headroom between the internal converter reference to V DD. V SS has this same absolute valued minimum, also measured from the VAG pin. The various modes of operation are summarized in Table 2. The RSI pin is functionally connected to V SS for the MC145507 and MC145508 pinouts. RxO, RxO Receive Analog Outputs These two complimentary outputs are generated from the output of the receive filter. They are equal in magnitude and out of phase. The maximum signal output of each is equal to the maximum peak–to–peak signal described with the reference. If a 3.15 V reference is used with RSI tied to VAG and a 3 dBm0 sine wave is decoded, the RxO output will be a 6.3 V peak–to–peak signal. RxO will also have an inverted signal output of 6.3 V peak–to–peak. External loads may be connected from RxO to RxO for a 6 dB push–pull signal gain or from either RxO or RxO to VAG. With a 3.15 V reference, each output will drive 600 Ω to 9 dBm. With RSI tied to VDD, each output will drive 900 Ω to 9 dBm. RxG Receive Output Gain Adjust (MC145506 Only) The purpose of the RxG pin is to allow external gain adjustment for the RxO pin. If RxG is left open, then the output signal at RxO will be inverted and output at RxO. Thus, the push–pull gain to a load from RxO to RxO is two times the output level at RxO. If external resistors are applied from RxO to RxG (RI) and from RxG to RxO (RG), the gain of RxO can be set differently from inverting unity. These resistors should be in the range of 10 kΩ. The RxO output level is unchanged by the resistors and the RxO gain is approximately equal to minus RG/RI. The actual gain is determined by taking into account the internal resistors which will be in parallel to these external resistors. The internal resistors have a large tolerance, but they match each other very closely. This matching tends to minimize the effects of their tolerance on external gain configurations. The circuit for RxG and RxO is shown in the Block Diagram. Txl Transmit Analog Input TxI is the input to the transmit filter. It is also the output of the transmit gain amplifier. The TxI input has an internal gain MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 9 Freescale Semiconductor, Inc. of 1.0, such that a 3 dBm0 signal at TxI corresponds to the peak converter reference voltage as described in the Vref and RSI pin descriptions. For a 3.15 V reference, the 3 dBm0 input should be 6.3 V peak–to–peak. ground accommodating TTL logic levels), and VAG = 0 V being tied to system analog ground. For single–supply applications, typical power supply configurations include: VDD = 10 V to 12 V VSS = 0 V VAG generates a mid supply voltage for referencing all analog signals. VLS controls the logic levels. This pin should be connected to VDD for CMOS logic levels from VSS to VDD. This pin should be connected to digital ground for true TTL logic input levels referenced to VLS, with HCMOS output levels from VLS to VDD. +Tx / –Tx Positive Tx Amplifier Input Negative Tx Amplifier Input The Txl pin is the input to the transmit band–pass filter. If +Tx or –Tx is available, then there is an internal amplifier preceding the filter whose pins are +Tx, –Tx, and TxI. These pins allow access to the amplifier terminals to tailor the input gain with external resistors. The resistors should be in the range of 10 kΩ. TESTING CONSIDERATIONS (MC145506 ONLY) Freescale Semiconductor, Inc... POWER SUPPLIES An analog test mode is activated by connecting MSI and CCI to 128 kHz. In this mode, the input of the A/D (the output of the Tx filter) is available at the PDI pin. This input is direct coupled to the A/D side of the codec. The A/D is a differential design. This results in the gain of this input being effectively attenuated by half. If monitored with a high–impedance buffer, the output of the Tx low–pass filter can also be measured at the PDI pin. This test mode allows independent evaluation of the transmit low–pass filter and A/D side of the codec. The transmit and receive channels of these devices are tested with the codec–filter fully functional. VDD Most Positive Power Supply VDD is typically 5 V to 12 V. VSS Most Negative Power Supply VSS is typically 10 V to 12 V negative of VDD. For a ±5 V dual–supply system, the typical power supply configuration is VDD = 5 V, VSS = –5 V, VLS = 0 V (digital MC145507 VAG 1 600 Ω VAG VDD RxO RDD +Tx RCE TxI RDC –Tx TDC Mu/A TDD PDI 8 V SS TDE 2 Rx 3 5 kΩ 10 kΩ 4 Tx 5 681 6 7 16 51 kΩ* 5V 0.1 µF 15 14 13 ENABLE CLOCK 12 11 10 9 VLS 0.1 µF –5 V * To define RDD when TDD is high Z. Figure 1. Test Circuit Table 1. MC145506 Options Available by Pin Selection RSI* Pin Level Vref* Pin Level Peak–to–Peak Overload Voltage (Txl, RxO) VDD VSS 7.56 Vp–p VDD VAG + VEXT (3.02 x VEXT) Vp–p VAG VSS 5 Vp–p VAG VAG + VEXT (2 x VEXT) Vp–p VSS VSS 6.3 Vp–p VSS VAG + VEXT (2.52 x VEXT) Vp–p * On MC145507/08, RSI and Vref are tied internally to V SS. MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 10 MOTOROLA Freescale Semiconductor, Inc. Table 2. Summary of Operation Conditions User Programmed Through Pins VDD, VAG, and VSS Pin Programmed Logic Level RSI Peak Overload Voltage Mu/A VLS VDD Mu–Law Companding Curve and D3/D4 Digital Formats with Zero Code Suppress 3.78 CMOS Logic Levels VAG Mu–Law Companding Curve and Sign Magnitude Data Format 2.50 TTL Input Levels, VAG Up; HCMOS Output Levels, VAG to VDD VSS A–Law Companding Curve and CCITT Digital Format 3.15 TTL Levels, VSS Up; HCMOS Output Levels, VSS to VDD Freescale Semiconductor, Inc... TDE tsu2 tP4 tsu1 TDC tsu8 tw 1 2 3 * 4 5 6 7 8 tP3 tP3 tP1 TDD tw fCL 9 10 11 tP2 tP2 MSB LSB PCM WORD REPEATED * Data output during this time will vary depending on TDC rate and TDE timing. Figure 2. Transmit Timing Diagram tw RCE tsu4 RDC RDD tw fCL tsu3 tw 1 2 3 4 5 6 7 8 9 10 11 th tsu5 DON’T CARE MSB DON’T CARE LSB Figure 3. Receive Timing Diagram tw MSI tsu7 tw tsu6 CCI 1 tw 2 3 4 5 6 7 8 9 10 11 Figure 4. MSI/CCI Timing Diagram MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 11 Freescale Semiconductor, Inc. 1.00 0.40 TYPICAL PERFORMANCE 0.60 GUARANTEED PERFORMANCE 0 –0.20 –0.40 –0.20 –0.40 –0.80 –50 –40 –30 –20 –10 INPUT LEVEL AT 1.02 kHz –1.00 –60 0 C–MESSAGE WEIGHTED VDD = 5 V VSS = –5 V 2048 kHz CLOCK 25.0 20.0 GUARANTEED PERFORMANCE 15.0 –50 –40 –30 –20 –10 INPUT LEVEL AT 1.02 kHz 40.0 0 C–MESSAGE WEIGHTED VDD = 5 V VSS = –5 V 2048 kHz CLOCK 30.0 25.0 20.0 GUARANTEED PERFORMANCE 15.0 10.0 –60 0 –50 –40 –30 –20 –10 INPUT LEVEL AT 1.02 kHz 0 Figure 8. MC145506 Quantization Distortion Mu–Law Receive 0.8 0.8 VDD = 5 V VSS = –5 V 2048 kHz CLOCK 0.4 0.2 0.4 TYPICAL PERFORMANCE 0 –0.2 –0.4 GUARANTEED PERFORMANCE –0.6 –50 –40 –30 VDD = 5 V VSS = –5 V 2048 kHz CLOCK 0.6 GAIN ERROR (dB) 0.6 GAIN ERROR (dB) –10 TYPICAL PERFORMANCE 35.0 Figure 7. MC145506 Quantization Distortion Mu–Law Transmit –0.8 –60 –40 –30 –20 INPUT LEVEL AT 1.02 kHz Figure 6. MC145506 Gain vs Level Mu–Law Receive QUANTIZATION DISTORTION (dB) TYPICAL PERFORMANCE 30.0 10.0 –60 –50 45.0 40.0 35.0 GUARANTEED PERFORMANCE TYPICAL PERFORMANCE 0 –0.60 45.0 QUANTIZATION DISTORTION (dB) 0.20 –0.80 Figure 5. MC145506 Gain vs Level Mu–Law Transmit Freescale Semiconductor, Inc... 0.40 –0.60 –1.00 –60 VDD = 5 V VSS = –5 V 2048 kHz CLOCK 0.80 GAIN ERROR (dB) GAIN ERROR (dB) 0.60 0.20 1.00 VDD = 5 V VSS = –5 V 2048 kHz CLOCK 0.80 0.2 0 –0.2 TYPICAL PERFORMANCE GUARANTEED PERFORMANCE –0.4 –0.6 –20 –10 INPUT LEVEL PSEUDO NOISE (dBm0) Figure 9. MC145506 Gain vs Level A–Law Transmit –0.8 –60 –50 –40 –30 –20 –10 INPUT LEVEL PSEUDO NOISE (dBm0) Figure 10. MC145506 Gain vs Level A–Law Receive MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 12 MOTOROLA 40.0 TYPICAL PERFORMANCE 35.0 GUARANTEED PERFORMANCE 30.0 25.0 PSOPHOMETRIC WEIGHTED VDD = 5 V VSS = –5 V 2048 kHz 20.0 15.0 10.0 –60 –50 –40 –30 –20 –10 40.0 QUANTIZATION DISTORTION (dB) QUANTIZATION DISTORTION (dB) Freescale Semiconductor, Inc. TYPICAL PERFORMANCE 35.0 30.0 25.0 PSOPHOMETRIC WEIGHTED VDD = 5 V VSS = –5 V 2048 kHz 20.0 15.0 10.0 0 –60 –50 INPUT LEVEL PSEUDO NOISE (dBm0) POWER SUPPLY REJECTION (dB) POWER SUPPLY REJECTION (dB) –30 –20 –10 0 Figure 12. MC145506 Quantization Distortion A–Law Receive TYPICAL PERFORMANCE 60 50 40 30 20 10 0 70 TYPICAL PERFORMANCE 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 0 100 10 20 30 POWER SUPPLY REJECTION (dB) 70 TYPICAL PERFORMANCE 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 FREQUENCY (kHz) Figure 15. MC145506 Power Supply Rejection Ratio Positive Receive VAC = 250 mVrms, C–Message Weighted MOTOROLA 50 60 70 80 90 100 Figure 14. MC145506 Power Supply Rejection Ratio Negative Transmit VAC = 250 mVrms, C–Message Weighted Figure 13. MC145506 Power Supply Rejection Ratio Positive Transmit VAC = 250 mVrms, C–Message Weighted 0 40 FREQUENCY (kHz) FREQUENCY (kHz) POWER SUPPLY REJECTION (dB) Freescale Semiconductor, Inc... –40 INPUT LEVEL PSEUDO NOISE (dBm0) Figure 11. MC145506 Quantization Distortion A–Law Transmit 70 GUARANTEED PERFORMANCE 100 70 TYPICAL PERFORMANCE 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 FREQUENCY (kHz) Figure 16. MC145506 Power Supply Rejection Ratio Negative Receive VAC = 250 mVrms, C–Message Weighted MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 13 Freescale Semiconductor, Inc. 0.2 2.0 0.1 0 0 –2.0 TYPICAL PERFORMANCE –0.2 –4.0 GAIN (dB) GAIN (dB) –0.1 GUARANTEED PERFORMANCE –0.3 –0.4 –6.0 –8.0 –0.5 –12.0 –0.6 –14.0 –0.7 –16.0 –0.8 TYPICAL PERFORMANCE –10.0 GUARANTEED PERFORMANCE –18.0 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 3.0 3.1 3.2 3.3 3.4 3.5 3.6 FREQUENCY (kHz) 0.2 –2.0 0.1 –0.1 TYPICAL PERFORMANCE GAIN (dB) GAIN (dB) TYPICAL PERFORMANCE 0 –6.0 –14.0 GUARANTEED PERFORMANCE –18.0 3.9 4.0 4.1 4.2 Figure 18. MC145506 Low–Pass Filter Response Transmit 2.0 –10.0 3.7 3.8 FREQUENCY (kHz) Figure 17. MC145506 Pass–Band Filter Response Transmit –0.2 GUARANTEED PERFORMANCE –0.3 –0.4 –0.5 –22.0 –0.6 –26.0 –0.7 –30.0 –0.8 0 0.04 0.08 0.12 0.16 FREQUENCY (kHz) 0.20 0.24 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 FREQUENCY (kHz) Figure 19. MC145506 High–Pass Filter Response Transmit Figure 20. MC145506 Pass–Band Filter Response Receive 2.0 0 GUARANTEED PERFORMANCE –2.0 –4.0 GAIN (dB) Freescale Semiconductor, Inc... GUARANTEED PERFORMANCE –6.0 –8.0 TYPICAL PERFORMANCE –10.0 –12.0 –14.0 –16.0 GUARANTEED PERFORMANCE –18.0 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 FREQUENCY (kHz) Figure 21. MC145506 Low–Pass Filter Response Receive MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 14 MOTOROLA Freescale Semiconductor, Inc. 2.048 MHz 18 pF 18 pF 10 MΩ 300 Ω 5V VCC R 0.1 µF OSC IN OSC OUT 1 2.048 MHz (TDC, RDC, CCI) OSC OUT 2 8 kHz (TDE, RCE, MSI) MC74HC4060 GND Q8 Q4 5V Freescale Semiconductor, Inc... J VCC 1/2 MC74HC73 K GND Q J Q K 1/2 MC74HC73 Q Q R R 5V 255 256 1 2 3 4 5 6 7 8 9 10 2.048 MHz 8 kHz Figure 22. Simple Clock Circuit for Driving MC145506/07/08 Codec–Filters MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 15 Freescale Semiconductor, Inc. N=1 R0 VAG VDD RxO RDD +Tx RCE TxI RDC –Tx TDC Mu/A TDD PDI TDE VSS VLS R0 N=2 –48 V 10 kΩ N=1 10 kΩ Freescale Semiconductor, Inc... MC145507 (a) Simplified Transformer Hybrid Using MC145507 N=1 R0 VAG VDD RxO RDD +Tx RCE TxI RDC –Tx TDC Mu/A TDD PDI TDE VSS VLS R3 N=2 R5 R4 –48 V R6 N=1 R1 R2 R0 = R3 ø R4 ø (R2 + R1) ≅ R3 ø R4 AV out = R0 ø R4 ø (R2 + R1) R3 + R0 ø R4 ø (R2 + R1) ≅ R0 ø R4 R3 + R0 ø R4 AV in = – R1 R2 MC145507 NOTE: Hybrid balance by R5 and R6 to equate the RxO signal gain at Txl through the inverting and non–inverting signal paths. (b) Universal Transformer Hybrid Using MC145507 Figure 23. Hybrid Interfaces to the MC145507 PCM Codec–Filter Mono–Circuit MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 16 MOTOROLA Freescale Semiconductor, Inc. R0 = 600 Ω VSS +Vref RSI VAG VDD RxO RDD RxG RCE RxO RDC +Tx TDC TxI CCI –Tx TDD Mu/A TDE PDI MSI VSS VLS R0 = 900 Ω N=1 R0 R5 R4 R6 R3 N=2 –48 V N=1 R0 Freescale Semiconductor, Inc... R2 R1 NOTE: Balance by R5 and R6 to equate the Txl gains through the inverting and non–inverting input signal paths, respectively, is given by: R1 R3 1– 2 × R2 R4 = 1+ R1 R2 R6 R3 – R5 + R6 R4 R5 R5 + R6 Tx Gain = R1/R2 Rx Gain = 1 + R3/R4 R5, R6 ≈ 10 kΩ Adjust Rx Gain with R3 Adjust Tx Gain with R1 MC145506 (a) Universal Transformer Hybrid Using MC145506 R0 = 600 Ω R0 = 900 Ω T N=1 10 kΩ VSS N=2 R0 +Vref RSI VAG VDD RxO 20 kΩ RxG –48 V N=1 R0 RxO R +Tx RDD RCE RDC TDC TxI CCI 20 kΩ –Tx 10 kΩ TDD Mu/A TDE PDI MSI VSS VLS MC145506 (b) Single–Ended Hybrid Using MC145506 Figure 24. Hybrid Interfaces to the MC145506 PCM Codec–Filter Mono–Circuit MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 17 RING TIP 75 Ω 0.0047 75 Ω –48 V 47 k 1N4002 0.1 –48 V 9 8 7 6 4 3 19.6 kΩ TIP111 TIP125 2 5 0.0047 0.0047 VEE EN BN RSI CC TSI BP EP VCC 1 kΩ 1 19.6 kΩ 1N4002 15 16 17 18 10 µF 50 V VQB HST 10 11 RSO 12 TSO 13 HSO 14 PDI TxO RxI VAG MC3419–1L R7 270 k Ω R3 42.2 k Ω R4 19.6 k Ω R1 30.1 k Ω 5V R5 126 k Ω (A0) 10 kΩ 10 kΩ 0.47 (A1) R2 143 k Ω 0.47 Freescale Semiconductor, Inc... –5 V 0.1 8 7 6 5 4 3 2 1 VSS PDI Mu/A –Tx TxI +Tx RxO VAG 16 V LS 9 TDE 10 TDD 11 TDC 12 RDC 13 RCE 14 RDD 15 VDD MC145507 5V 0.1 Freescale Semiconductor, Inc. Figure 25. A Complete Single Party Channel Unit Using MC3419 SLIC and MC145507 PCM Mono–Circuit MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 18 MOTOROLA MOTOROLA Refer to AN968 for more information. C5 Tx– µ /A TxI VDD RxO Tx+ VAG V LS C4 MC145507 HANDSET R1 5 6 4 16 2 3 1 9 MC145412 R2 R5 R6 R3 C2 C3 R9 OSC C4 OSC MS MO VSS OH OPL VDD PDI TDC RDC RCE RDD TDD TDE VSS 7 12 13 14 15 11 10 8 2 NC 8 10 11 6 12 17 9 1 R10 SW2 X2 R36 –5 V R35 Q5 R34 LED C1 Q2 R15 R13 C13 SYNC TO POWER SUPPLY SW1 R14 R11 4 V in 1 CD 3 FC1 2 FC2 Q1 R12 C14 R24 C10 C12 D5 C15 5V VDD DI3 DO3 DO2 DI2 DI1 DO1 VSS VCC Tx3 Rx3 Rx2 Tx2 Tx1 Rx1 GND 9 16 7 6 4 5 3 2 9 8 7 6 17 13 14 18 19 12 SO2 SI2 SO1 SI1 CLK TE1 Tx Rx RE1 TE VSS VDD X2 PD X1 µ /A LO2 LB LO1 LI VD Vref 2 C9 22 16 11 15 10 20 4 21 3 5 –5 V 5V 1 20 TxS VDD 17 4 DOE BRCLK 14 3 DL DIE 2 9 SB TxD 11 6 BR1 RxD 12 7 BR2 RxS 19 8 RST BR3 5 15 DCLK BCLK 18 16 CM DCO 13 10 VSS DCI 1 10 11 13 12 14 15 8 MC145428 R4 R7 R8 5V 1 2 3 4 5 6 7 8 9 * 0 # 5 16 15 14 13 18 7 C1 C2 C3 R1 R2 R3 R4 DTMF OUT TSO MC34119 4 5V 5 VO1 8 V 6 O2 VCC 7 GND R25 MC145406 3 SW1: CLOSED = ON-HOOK OPEN = OFF-HOOK SPEAKER R23 5V Freescale Semiconductor, Inc... C11 X1 C8 R16 5V R37 – R41 C6 C7 TIP RING TO POWER SUPPLY V in SW3 – SW7 5V FEMALE DB–25 Freescale Semiconductor, Inc. MC145426 Figure 26. Digital Telephone Schematic MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 19 Freescale Semiconductor, Inc. Table 3. Mu–Law Encode–Decode Characteristics Chord Number Number of Steps Step Size Normalized Encode Decision Levels Digital Code 1 2 3 4 5 6 7 8 Sign Chord Chord Chord Step Step Step Step Normalized Decode Levels 1 0 0 0 0 0 0 0 8031 1 0 0 0 1 1 1 1 4191 1 0 0 1 1 1 1 1 2079 1 0 1 0 1 1 1 1 1023 1 0 1 1 1 1 1 1 495 1 1 0 0 1 1 1 1 231 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 0 2 1 1 1 1 1 1 1 1 0 8159 256 … 16 … 8 … 7903 4319 7 16 128 … … … 4063 2143 16 64 … 1055 5 16 32 … … … 991 511 4 16 16 … … … 479 239 3 16 8 … … … 223 103 99 2 16 4 … … … 95 35 33 1 15 2 … … 31 … Freescale Semiconductor, Inc... 6 … … 2015 3 1 1 1 0 NOTES: 1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values. 2. Digital code includes inversion of all magnitude bits. MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 20 MOTOROLA Freescale Semiconductor, Inc. Table 4. A–Law Encode–Decode Characteristics Chord Number Number of Steps Step Size Normalized Encode Decision Levels Digital Code 1 2 3 4 5 6 7 8 Sign Chord Chord Chord Step Step Step Step Normalized Decode Levels 1 0 1 0 1 0 1 0 4032 1 0 1 0 0 1 0 1 2112 1 0 1 1 0 1 0 1 1056 1 0 0 0 0 1 0 1 528 1 0 0 1 0 1 0 1 264 1 1 1 0 0 1 0 1 132 1 1 1 1 0 1 0 1 1 1 0 1 0 1 0 1 4096 128 … 16 … 7 … 3968 2176 6 16 64 … … … 2048 1088 16 32 … 544 4 16 16 … … … 512 272 3 16 8 … … … 256 136 2 16 4 … … … 128 68 66 1 32 2 … … 64 … Freescale Semiconductor, Inc... 5 … … 1024 2 1 0 NOTES: 1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values. 2. Digital code includes alternate bit inversion, as specified by CCITT. MOTOROLA MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 21 Freescale Semiconductor, Inc. PACKAGE DIMENSIONS DW SUFFIX SOG PACKAGE CASE 751–03 (MC145507/08) A D 9 1 8 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INLCUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. 16X M T A S B DIM A A1 B C D E e H h L S 14X e L A 0.25 B B SEATING PLANE A1 Freescale Semiconductor, Inc... h X 45 _ E 0.25 H 8X M B M 16 q q C T MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 10.15 10.45 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_ P SUFFIX PLASTIC DIP CASE 648–08 (MC145507/08) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. –A– 16 9 1 8 B F C L S –T– SEATING PLANE K H G D J 16 PL 0.25 (0.010) M T A M M DIM A B C D F G H J K L M S MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 22 INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 MOTOROLA Freescale Semiconductor, Inc. P SUFFIX PLASTIC DIP CASE 708–04 (MC145506) 22 NOTES: 1. POSITIONAL TOLERANCE OF LEADS (D), SHALL BE WITHIN 0.25 (0.010) AT MAXIMUM MATERIAL CONDITION, IN RELATION TO SEATING PLANE AND EACH OTHER. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 12 B 1 11 L A NC Freescale Semiconductor, Inc... K H MOTOROLA G F D SEATING PLANE M J DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 27.56 28.32 8.64 9.14 3.94 5.08 0.36 0.56 1.27 1.78 2.54 BSC 1.02 1.52 0.20 0.38 2.92 3.43 10.16 BSC 0_ 15_ 0.51 1.02 INCHES MIN MAX 1.085 1.115 0.340 0.360 0.155 0.200 0.014 0.022 0.050 0.070 0.100 BSC 0.040 0.060 0.008 0.015 0.115 0.135 0.400 BSC 0_ 15 _ 0.020 0.040 MC145506•MC145507•MC145508 For More Information On This Product, Go to: www.freescale.com 23 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado, 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569 Mfax : [email protected] – TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, Motorola Fax Back System – US & Canada ONLY 1-800-774-1848 2 Dai King Street, Tai Po Industrial Estate, Tao Po, N.T., Hong Kong. – http://sps.motorola.com /mfax / 852-26668334 HOME PAGE : http://motorola.com/sps / CUSTOMER FOCUS CENTER: 1-800-521-6274 ◊For More Information On This Product, MC145506•MC145507•MC145508 Go to: www.freescale.com 24 MC145506/D MOTOROLA