2010.7 Compliant www.cosel.co.jp/en On Board Type DC-DC converter MG15/30 series Compact and general use type Isolated type DC-DC converter 10 years warranty MG15/30 series Contents Contents 1 Features of MG series 2 MGS15 3 MGS30 5 MGW15 7 MGW30 9 MGFS15 11 MGFS30 13 MGFW15 15 MGFW30 17 Item Model External view MG15 Input voltage [V] Output voltage[V] / Output current[A] External dimension Single output 2 output [mm] WXHXD 3.3[V] 5[V] 12[V] 15[V] ±5(+10)[V] ±12(+24)[V] ±15(+30)[V] DC9-18 4 3 1.3 1 1.5 0.65 0.5 DC18-36 4 3 1.3 1 1.5 0.65 0.5 DC36-76 4 3 1.3 1 1.5 0.65 0.5 DC9-36 4 3 1.3 1 1.5 0.65 0.5 MGF15 25.4X9.9X25.4 (Wide input) MG30 DC18-76 4 3 1.3 1 1.5 0.65 0.5 DC9-18 8 6 2.5 2 2.5 1.25 1 DC18-36 8 6 2.5 2 2.5 1.25 1 DC36-76 8 6 2.5 2 2.5 1.25 1 DC9-36 7.5 6 2.5 2 2 1.25 1 MGF30 25.4X9.9X50.8 25.4X9.9X50.8 (Wide input) DC18-76 1 25.4X9.9X25.4 7.5 6 2.5 2 2 1.25 1 Compact, general use and isolated type DC-DC converter MG15/30 series Lineup of 70 models World standard 1 1inch, 1 2 inch Isolated type DC-DC converter When compared to conventional models (our ZU series), downsizing and light-weighted system are achieved. Thus, long-term reliability and high efficiency are both achieved. In 15/30W class, wide input type are added. With whelming variations, free choice than ever is achieved. Thus, RoHS compliant product that is environment friendly. ¡Best-matching to downsizing of the board area ¡High efficiency, light-weighted, compact size When compared to conventional systems (*1), footprint area on board is 40% or smaller. Compact sizing and light-weighted are achieved by applying synchronized rectification circuit. 30% 40% in 1 1 in ch ZU15 95.0 ZU25 MG30 MG15 MGS152405 MGS302405 ZUS152405 ZUS252405 85.0 80.0 1 inch 2 inches 92% 90% 90.0 Efficiency [%] Footprint ratio ch Footprint ratio 8 Approx. % of efficiency is increased when compared to conventional units *1 ZU series ¡Noise countermeasure with 6-side shield. As well as a case, the bottom surface is also shielded for lowering the noise. Bottom shield effect 75.0 0 1.0 2.0 3.0 4.0 5.0 6.0 Output current [A] ¡Wide input type is newly added to the lineup. Conventionally, two systems were used depending on input voltage. With MG series wide input type, only one system is required. Therefore, power supply can be used commonly. 5-side shield 6-side shield Noise levels at a center of the bottom side in MG series are compared. 12V series 24V series ¡Isolation DC1,500V (1 min.) Isolation between input and output is DC1,500V (1 min) and safety level has been increased. Between input output Conventionally, systems of two types were required. However, corresponding with one system is now available. ¡10 years warranty Reducing the management cost By securing reliability of parts soldering sections, long-term reliability has been achieved. ¡Other features Warping amount simulation at the ceramic capacitor electrode with a stress simulator. ¿Wide operating temperature range (-40 to +85ª) ¿Remote control function ¿Output voltage external variation function (single output) ¿Fuse is built-in at the input side ¿Built-in synchronized rectification circuit (single output) ¿Aluminum electrolysis / tantalum electrolytic capacitor unused ¿Safety standard (UL, C-UL, EN) certifications 2 Ordering information On-board type MGS15 MG 1 S 2 15 3 24 4 *Link to www.cosel.co.jp/en for the latest product information. MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] *1 MGS15123R3 13.2 3.3 4 MGS151205 15 5 3 MGS151212 15.6 12 1.3 MGS151215 15 15 1 MGS15243R3 13.2 3.3 4 MGS152405 15 5 3 05 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MGS152412 15.6 12 1.3 MGS152415 15 15 1 SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND REMOTE ON/OFF OTHERS MGS15123R3 MGS151205 MGS151212 MGS151215 MGS15243R3 MGS152405 DC9 - 18 DC18 - 36 1.28typ 1.44typ 1.49typ 1.42typ 0.63typ 0.70typ 86typ 87typ 87typ 88typ 87typ 89typ 3.3 5 12 15 3.3 5 4 3 1.3 1 4 3 13.2max 20max 48max 60max 13.2max 20max 13.2max 20max 48max 60max 13.2max 20max 75max 75max 100max 100max 75max 75max 100max 100max 120max 120max 100max 100max 100max 100max 120max 120max 100max 100max 200max 200max 200max 200max 200max 200max 50max 50max 150max 180max 50max 50max 80max 80max 240max 290max 80max 80max 20max 20max 48max 60max 20max 20max 30max (Minimum input, Io=100%) Fixed (TRM pin open) Available to adjust ±10% by external variable resister 3.296 - 3.404 4.975 - 5.137 11.857 - 12.243 14.839 - 15.321 3.296 - 3.404 4.975 - 5.137 Works over 105% of rating and recovers automatically Provided (Negative logic L:ON, H:OFF) MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] MGS15483R3 13.2 3.3 4 INPUT OUTPUT *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 *1 MGS154805 15 5 3 MGS154812 15.6 12 1.3 MGS154815 15 15 1 SPECIFICATIONS INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND REMOTE ON/OFF OTHERS 3 MGS15483R3 MGS154805 MGS154812 MGS154815 DC36 - 76 0.32typ 0.35typ 0.36typ 0.35typ 87typ 89typ 90typ 90typ 3.3 5 12 15 4 3 1.3 1 13.2max 20max 48max 60max 13.2max 20max 48max 60max 75max 75max 100max 100max 100max 100max 120max 120max 100max 100max 120max 120max 200max 200max 200max 200max 50max 50max 150max 180max 80max 80max 240max 290max 20max 20max 48max 60max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 11.857 - 12.243 14.839 - 15.321 Works over 105% of rating and recovers automatically Provided (Negative logic L:ON, H:OFF) MGS152412 MGS152415 0.73typ 89typ 12 1.3 48max 48max 100max 120max 120max 200max 150max 240max 48max 0.70typ 89typ 15 1 60max 60max 100max 120max 120max 200max 180max 290max 60max 11.857 - 12.243 14.839 - 15.321 MGS15 GENERAL SPECIFICATIONS ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X25.4mm (WXHXD) / 20g max COOLING METHOD Convection/Forced air MGW15xx05/MGW15xx12/MGW15xx15 is available as single output, +10V/+24V/+30V Rated input 12V, 24V or 48V DC lo=100% Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC12V, DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm 10.16 +Vout 25.4 TRM 10.16 -Vin 7.62 5.08 +Vin RC 2.54 *1 *2 *3 *4 *5 * STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 20g or less -Vout 20.32 25.4 4 Ordering information On-board type MGS30 MG 1 S 2 30 3 24 4 *Link to www.cosel.co.jp/en for the latest product information. MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] MGS301205 30 5 6 MGS301212 30 12 2.5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MGS301215 30 15 2 MGS30243R3 26.4 3.3 8 MGS302405 30 5 6 MGS30243R3 DC18 - 36 1.22typ 90typ 3.3 8 13.2max 13.2max 75max 100max 100max 200max 50max 80max 20max MGS302405 MGS302412 MGS302415 1.36typ 92typ 5 6 20max 20max 75max 100max 100max 200max 50max 80max 20max 1.37typ 91typ 12 2.5 48max 48max 100max 120max 120max 200max 150max 240max 48max 1.37typ 91typ 15 2 60max 60max 100max 120max 120max 200max 180max 290max 60max 3.296 - 3.404 4.975 - 5.137 11.857 - 12.243 14.839 - 15.321 PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND OVERVOLTAGE PROTECTION[V] OTHERS REMOTE ON/OFF MGS30123R3 MGS301205 MGS301212 MGS301215 DC9 - 18 2.47typ 2.78typ 2.78typ 2.78typ 89typ 90typ 90typ 90typ 3.3 5 12 15 8 6 2.5 2 13.2max 20max 48max 60max 13.2max 20max 48max 60max 75max 75max 100max 100max 100max 100max 120max 120max 100max 100max 120max 120max 200max 200max 200max 200max 50max 50max 150max 180max 80max 80max 240max 290max 20max 20max 48max 60max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 11.857 - 12.243 14.839 - 15.321 Works over 105% of rating and recovers automatically Works over 120 to 160% of rating Provided (Negative logic L:ON, H:OFF) MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] MGS30483R3 26.4 3.3 8 *1 MGS30123R3 26.4 3.3 8 05 5 MGS302412 30 12 2.5 MGS302415 30 15 2 SPECIFICATIONS INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 *1 MGS304805 30 5 6 MGS304812 30 12 2.5 MGS304815 30 15 2 SPECIFICATIONS INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND OVERVOLTAGE PROTECTION[V] OTHERS REMOTE ON/OFF 5 MGS30483R3 MGS304805 MGS304812 MGS304815 DC36 - 76 0.61typ 0.69typ 0.69typ 0.69typ 90typ 91typ 91typ 91typ 3.3 5 12 15 8 6 2.5 2 13.2max 20max 48max 60max 13.2max 20max 48max 60max 75max 75max 100max 100max 100max 100max 120max 120max 100max 100max 120max 120max 200max 200max 200max 200max 50max 50max 150max 180max 80max 80max 240max 290max 20max 20max 48max 60max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 11.857 - 12.243 14.839 - 15.321 Works over 105% of rating and recovers automatically Works over 120 to 160% of rating Provided (Negative logic L:ON, H:OFF) MGS30 GENERAL SPECIFICATIONS ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 * STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X50.8mm (WXHXD) / 40g max COOLING METHOD Convection/Forced air MGW30xx05/MGW30xx12/MGW30xx15 is available as single output, +10V/+24V/+30V Rated input 12V, 24V or 48V DC lo=100% Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC12V, DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm +Vout -Vin 25.4 10.16 5.08 +Vin 10.16 10.16 -Vout RC 5.08 TRM ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 40g or less 45.72 50.8 6 Ordering information On-board type MGW15 MG 1 W 2 15 24 3 05 4 *Link to www.cosel.co.jp/en for the latest product information. 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MODEL MGW151205 MGW151212 MGW151215 MGW152405 MGW152412 MGW152415 MGW154805 MGW154812 MGW154815 MAX OUTPUT WATTAGE[W] 15 15.6 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 1.5 0.65 0.65 0.65 *1 VOLTAGE[V] DC OUTPUT CURRENT[A]] 15 0.5 15 15.6 1.5 15 0.5 15 15.6 1.5 15 0.5 SPECIFICATIONS MODEL MGW151205 MGW151212 MGW151215 MGW152405 MGW152412 MGW152415 MGW154805 MGW154812 MGW154815 DC9 - 18 VOLTAGE[V] INPUT DC18 - 36 DC36 - 76 CURRENT[A] *2 1.48typ 1.49typ 1.42typ 0.74typ 0.74typ 0.70typ 0.37typ 0.37typ 0.35typ EFFICIENCY[%] *2 84typ 87typ 88typ 84typ 88typ 89typ 84typ 89typ 89typ VOLTAGE[V] ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) CURRENT[A] 1.5 0.65 0.5 1.5 0.65 0.5 1.5 0.65 0.5 40max 60max 60max 75max 40max 60max 75max 600max 750max 500max 75max 40max *3 500max *5 600max 750max 500max *4 250max 480max 600max 250max 480max 600max -20 to +60C 100max 100max 100max 100max 100max -40 to -20C 120max 120max 120max 120max 120max -20 to +60C 120max 120max 120max 120max -40 to -20C 200max 200max 200max -20 to +60C 50max 150max -40 to -20C 80max LINE REGULATION[mV] CROSS REGULATION[mV] RIPPLE[mVp-p] *6 OUTPUT RIPPLE NOISE[mVp-p] *6 TEMPERATURE REGULATION[mV] DRIFT[mV] *7 START-UP TIME[ms] 50max *5 *5 600max 750max 250max 480max 600max 100max 100max 100max 100max 120max 120max 120max 120max 120max 120max 120max 120max 120max 200max 200max 200max 200max 200max 200max 180max 50max 150max 180max 50max 150max 180max 240max 290max 80max 240max 290max 80max 240max 290max 50max 60max 50max 50max 60max 50max 50max 60max 30max (Minimum input, Io=100%) OUTPUT VOLTAGE SETTING[V]*8 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 PROTECTION OVERCURRENT PROTECTION[V] Works over 105% of rating and recovers automatically CIRCUIT AND OTHERS REMOTE ON/OFF Provided (Negative logic L:ON, H:OFF) ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 *6 *7 7 STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X25.4mm (WXHXD) / 20g max COOLING METHOD Convection/Forced air Single output +10V, +24V, +30V with no use of COM. Rated input 12V, 24V or 48V lo=100% An output load is 100%, the other load is 5% to 100%. An output load is 100%, the other load is 20% to 100%. Refer to the instruction manual 11. Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. *8 * Rated input voltage (DC12V, DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. MGW15 External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm 10.16 +Vout 2.54 25.4 COM -Vin 10.16 7.62 5.08 +Vin RC ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 20g or less -Vout 20.32 25.4 8 Ordering information On-board type MGW30 MG 1 W 2 30 24 3 05 4 *Link to www.cosel.co.jp/en for the latest product information. 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MODEL MGW301205 MGW301212 MGW301215 MGW302405 MGW302412 MGW302415 MGW304805 MGW304812 MGW304815 MAX OUTPUT WATTAGE[W] 25 30 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 2.5 1.25 1.25 1.25 *1 VOLTAGE[V] DC OUTPUT CURRENT[A]] 30 1 25 30 2.5 30 1 25 30 2.5 30 1 SPECIFICATIONS MODEL MGW301205 MGW301212 MGW301215 MGW302405 MGW302412 MGW302415 MGW304805 MGW304812 MGW304815 DC9 - 18 VOLTAGE[V] INPUT DC18 - 36 DC36 - 76 CURRENT[A] *2 2.42typ 2.81typ 2.81typ 1.21typ 1.40typ 1.40typ 0.61typ 0.70typ 0.70typ EFFICIENCY[%] *2 86typ 89typ 89typ 86typ 89typ 89typ 86typ 89typ 89typ VOLTAGE[V] ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) CURRENT[A] 2.5 1.25 1 2.5 1.25 1 2.5 1.25 1 40max 60max 60max 75max 40max 60max 75max 600max 750max 500max 75max 40max *3 500max *5 600max 750max 500max *4 250max 480max 600max 250max 480max 600max -20 to +60C 100max 100max 100max 100max 100max -40 to -20C 120max 120max 120max 120max 120max -20 to +60C 120max 120max 120max 120max -40 to -20C 200max 200max 200max -20 to +60C 50max 150max -40 to -20C 80max LINE REGULATION[mV] CROSS REGULATION[mV] RIPPLE[mVp-p] *6 OUTPUT RIPPLE NOISE[mVp-p] *6 TEMPERATURE REGULATION[mV] DRIFT[mV] *7 START-UP TIME[ms] 50max *5 *5 600max 750max 250max 480max 600max 100max 100max 100max 100max 120max 120max 120max 120max 120max 120max 120max 120max 120max 200max 200max 200max 200max 200max 200max 180max 50max 150max 180max 50max 150max 180max 240max 290max 80max 240max 290max 80max 240max 290max 50max 60max 50max 50max 60max 50max 50max 60max 30max (Minimum input, Io=100%) OUTPUT VOLTAGE SETTING[V]*8 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 PROTECTION OVERCURRENT PROTECTION[V] Works over 105% of rating and recovers automatically CIRCUIT AND OVERVOLTAGE PROTECTION[V] Works over 120 to 160% of rating OTHERS REMOTE ON/OFF Provided (Negative logic L:ON, H:OFF) ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 *6 9 STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X50.8mm (WXHXD) / 40g max COOLING METHOD Convection/Forced air Single output +10V, +24V, +30V with no use of COM. Rated input 12V, 24V or 48V DC lo=100% Symmetrical loading from 5% to 100%. Symmetrical loading from 20% to 100%. Refer to the instruction manual 11. Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. *7 *8 * Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC12V, DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. MGW30 External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm +Vout 10.16 5.08 +Vin -Vin 25.4 10.16 10.16 COM RC 5.08 -Vout ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 40g or less 45.72 50.8 10 Ordering information On-board type MGFS15 MGF 1 S 2 15 3 24 4 *Link to www.cosel.co.jp/en for the latest product information. MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] *1 MGFS15243R3 13.2 3.3 4 MGFS152405 15 5 3 05 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MGFS152412 15.6 12 1.3 MGFS152415 15 15 1 MGFS152412 MGFS152415 0.73typ 89typ 12 1.3 48max 48max 100max 120max 120max 200max 150max 240max 48max 0.70typ 89typ 15 1 60max 60max 100max 120max 120max 200max 180max 290max 60max 11.857 - 12.243 14.839 - 15.321 MGFS154812 15.6 12 1.3 MGFS154815 15 15 1 MGFS154812 MGFS154815 0.37typ 88typ 12 1.3 48max 48max 100max 120max 120max 200max 150max 240max 48max 0.35typ 89typ 15 1 60max 60max 100max 120max 120max 200max 180max 290max 60max 11.857 - 12.243 14.839 - 15.321 SPECIFICATIONS PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND REMOTE ON/OFF OTHERS MGFS15243R3 MGFS152405 DC9 - 36 0.63typ 0.71typ 87typ 88typ 3.3 5 4 3 13.2max 20max 13.2max 20max 75max 75max 100max 100max 100max 100max 200max 200max 50max 50max 80max 80max 20max 20max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 Works over 105% of rating and recovers automatically Provided (Negative logic L:ON, H:OFF) MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] MGFS15483R3 13.2 3.3 4 INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 *1 MGFS154805 15 5 3 SPECIFICATIONS INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND REMOTE ON/OFF OTHERS 11 MGFS15483R3 MGFS154805 DC18 - 76 0.32typ 0.36typ 87typ 88typ 3.3 5 4 3 13.2max 20max 13.2max 20max 75max 75max 100max 100max 100max 100max 200max 200max 50max 50max 80max 80max 20max 20max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 Works over 105% of rating and recovers automatically Provided (Negative logic L:ON, H:OFF) MGFS15 GENERAL SPECIFICATIONS ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X25.4mm (WXHXD) / 20g max COOLING METHOD Convection/Forced air MGFW15xx05/MGFW15xx12/MGFW15xx15 is available as single output, +10V/+24V/+30V Rated input 12V, 24V or 48V DC lo=100% Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm 10.16 +Vout 25.4 TRM 10.16 -Vin 7.62 5.08 +Vin RC 2.54 *1 *2 *3 *4 *5 * STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 20g or less -Vout 20.32 25.4 12 Ordering information On-board type MGFS30 MGF 1 S 2 30 3 24 4 *Link to www.cosel.co.jp/en for the latest product information. MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] *1 MGFS30243R3 24.75 3.3 7.5 MGFS302405 30 5 6 05 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MGFS302412 30 12 2.5 MGFS302415 30 15 2 MGFS302412 MGFS302415 1.40typ 89typ 12 2.5 48max 48max 100max 120max 120max 200max 150max 240max 48max 1.40typ 89typ 15 2 60max 60max 100max 120max 120max 200max 180max 290max 60max 11.857 - 12.243 14.839 - 15.321 MGFS304812 30 12 2.5 MGFS304815 30 15 2 MGFS304812 MGFS304815 0.70typ 89typ 12 2.5 48max 48max 100max 120max 120max 200max 150max 240max 48max 0.70typ 89typ 15 2 60max 60max 100max 120max 120max 200max 180max 290max 60max 11.857 - 12.243 14.839 - 15.321 SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND OVERVOLTAGE PROTECTION[V] OTHERS REMOTE ON/OFF MGFS30243R3 MGFS302405 DC9 - 36 1.17typ 1.40typ 88typ 89typ 3.3 5 7.5 6 13.2max 20max 13.2max 20max 75max 75max 100max 100max 100max 100max 200max 200max 50max 50max 80max 80max 20max 20max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 Works over 105% of rating and recovers automatically Works over 120 to 160% of rating Provided (Negative logic L:ON, H:OFF) MODEL MAX OUTPUT WATTAGE[W] VOLTAGE[V] DC OUTPUT CURRENT[A]] MGFS30483R3 24.75 3.3 7.5 INPUT OUTPUT *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 *1 MGFS304805 30 5 6 SPECIFICATIONS INPUT OUTPUT MODEL VOLTAGE[V] CURRENT[A] EFFICIENCY[%] VOLTAGE[V] CURRENT[A] *2 *2 LINE REGULATION[mV] LOAD REGULATION[mV] -20 to +60C RIPPLE[mVp-p] *3 -40 to -20C -20 to +60C RIPPLE NOISE[mVp-p] *3 -40 to -20C -20 to +60C TEMPERATURE REGULATION[mV] -40 to -20C *4 DRIFT[mV] START-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V]*5 PROTECTION OVERCURRENT PROTECTION[V] CIRCUIT AND OVERVOLTAGE PROTECTION[V] OTHERS REMOTE ON/OFF 13 MGFS30483R3 MGFS304805 DC18 - 76 0.59typ 0.70typ 88typ 89typ 3.3 5 7.5 6 13.2max 20max 13.2max 20max 75max 75max 100max 100max 100max 100max 200max 200max 50max 50max 80max 80max 20max 20max 30max (Minimum input, Io=100%) Fixed (TRM pin open) ±10% adjustable by external VR 3.296 - 3.404 4.975 - 5.137 Works over 105% of rating and recovers automatically Works over 120 to 160% of rating Provided (Negative logic L:ON, H:OFF) MGFS30 GENERAL SPECIFICATIONS ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 * STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X50.8mm (WXHXD) / 40g max COOLING METHOD Convection/Forced air MGFW30xx05/MGFW30xx12/MGFW30xx15 is available as single output, +10V/+24V/+30V Rated input 12V, 24V or 48V DC lo=100% Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm +Vout -Vin 25.4 10.16 5.08 +Vin 10.16 10.16 -Vout RC 5.08 TRM ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 40g or less 45.72 50.8 14 Ordering information On-board type MGFW15 MGF 1 W 2 15 24 3 05 4 *Link to www.cosel.co.jp/en for the latest product information. 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MODEL MGFW152405 MGFW152412 MGFW152415 MGFW154805 MGFW154812 MGFW154815 MAX OUTPUT WATTAGE[W] 15 15.6 15 15 15.6 15 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 1.5 0.65 0.5 1.5 0.65 0.5 MODEL MGFW152405 MGFW152412 MGFW152415 MGFW154805 MGFW154812 MGFW154815 VOLTAGE[V] DC9 - 36 *1 VOLTAGE[V] DC OUTPUT CURRENT[A]] SPECIFICATIONS INPUT DC18 - 76 CURRENT[A] *2 0.74typ 0.74typ 0.70typ 0.37typ 0.37typ 0.36typ EFFICIENCY[%] *2 84typ 88typ 89typ 84typ 87typ 88typ VOLTAGE[V] ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) CURRENT[A] 1.5 0.65 0.5 1.5 0.65 0.5 60max 75max 40max 60max 75max 40max *3 500max *5 600max 750max 500max *4 250max 480max 600max -20 to +60C 100max 100max -40 to -20C 120max 120max -20 to +60C 120max LINE REGULATION[mV] 600max 750max 250max 480max 600max 100max 100max 100max 100max 120max 120max 120max 120max 120max 120max 120max 120max 120max -40 to -20C 200max 200max 200max 200max 200max 200max -20 to +60C 50max 150max 180max 50max 150max 180max -40 to -20C 80max 240max 290max 80max 240max 290max 50max 60max 50max 50max 60max 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 CROSS REGULATION[mV] RIPPLE[mVp-p] *6 OUTPUT RIPPLE NOISE[mVp-p] *6 TEMPERATURE REGULATION[mV] *5 DRIFT[mV] *7 START-UP TIME[ms] 50max 30max (Minimum input, Io=100%) OUTPUT VOLTAGE SETTING[V]*8 4.935 - 5.240 11.765 - 12.492 PROTECTION OVERCURRENT PROTECTION[V] Works over 105% of rating and recovers automatically CIRCUIT AND OTHERS REMOTE ON/OFF Provided (Negative logic L:ON, H:OFF) ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 *6 *7 15 STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X25.4mm (WXHXD) / 20g max COOLING METHOD Convection/Forced air Single output +10V, +24V, +30V with no use of COM. Rated input 12V, 24V or 48V DC lo=100% Symmetrical loading from 5% to 100%. Symmetrical loading from 20% to 100%. Refer to the instruction manual 11. Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. *8 * Rated input voltage (DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. MGFW15 External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm 10.16 +Vout 2.54 25.4 COM -Vin 10.16 7.62 5.08 +Vin RC ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 20g or less -Vout 20.32 25.4 16 Ordering information On-board type MGFW30 MGF 1 W 2 30 24 3 05 4 *Link to www.cosel.co.jp/en for the latest product information. 5 -O 6 1Series name 2Single output 3Output wattage 4Input voltage 5Output voltage 6Optional G : Capacitor between Input and Output is removed. R : with Remote ON/OFF (Positive logic control) MODEL MGFW302405 MGFW302412 MGFW302415 MGFW304805 MGFW304812 MGFW304815 MAX OUTPUT WATTAGE[W] 20 30 30 20 30 30 ±5 or +10 ±12 or +24 ±15 or +30 ±5 or +10 ±12 or +24 ±15 or +30 2 1.25 1 2 1.25 1 MODEL MGFW302405 MGFW302412 MGFW302415 MGFW304805 MGFW304812 MGFW304815 VOLTAGE[V] DC9 - 36 *1 VOLTAGE[V] DC OUTPUT CURRENT[A]] SPECIFICATIONS INPUT DC18 - 76 CURRENT[A] *2 0.98typ 1.44typ 1.44typ 0.49typ 0.72typ 0.72typ EFFICIENCY[%] *2 85typ 87typ 87typ 85typ 87typ 87typ VOLTAGE[V] ±5(+10) ±12(+24) ±15(+30) ±5(+10) ±12(+24) ±15(+30) CURRENT[A] 2 1.25 1 2 1.25 1 60max 75max 40max 60max 75max 40max *3 500max *5 600max 750max 500max *4 250max 480max 600max -20 to +60C 100max 100max -40 to -20C 120max 120max -20 to +60C 120max LINE REGULATION[mV] 600max 750max 250max 480max 600max 100max 100max 100max 100max 120max 120max 120max 120max 120max 120max 120max 120max 120max -40 to -20C 200max 200max 200max 200max 200max 200max -20 to +60C 50max 150max 180max 50max 150max 180max -40 to -20C 80max 240max 290max 80max 240max 290max 50max 60max 50max 50max 60max 14.602 - 15.505 4.935 - 5.240 11.765 - 12.492 14.602 - 15.505 CROSS REGULATION[mV] RIPPLE[mVp-p] *6 OUTPUT RIPPLE NOISE[mVp-p] *6 TEMPERATURE REGULATION[mV] *5 DRIFT[mV] *7 START-UP TIME[ms] 50max 30max (Minimum input, Io=100%) OUTPUT VOLTAGE SETTING[V]*8 4.935 - 5.240 11.765 - 12.492 PROTECTION OVERCURRENT PROTECTION[V] Works over 105% of rating and recovers automatically CIRCUIT AND OVERVOLTAGE PROTECTION[V] Works over 120 to 160% of rating OTHERS REMOTE ON/OFF Provided (Negative logic L:ON, H:OFF) ISOLATION INPUT-OUTPUT DC1,500V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) INPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OUTPUT-CASE DC1,000V 1minute, Cutoff current = 10mA, DC500V 1,000MW min (20±15C) OPERATING TEMP.,HUMID.AND ALTITUDE -40 to +85C, 20 to 95%RH (Non condensing) (Required Derating), 3,000m (10,000feet) max ENVIRONMENT SAFETY OTHERS *1 *2 *3 *4 *5 *6 17 STORAGE TEMP.,HUMID.AND ALTITUDE -40 to +100C, 20 to 95%RH (Non condensing), 9,000m (30,000feet) max VIBRATION 10 - 55Hz, 98.0m/s2 (10G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 490.3m/s2 (50G), 11ms, once each along X, Y and Z axis AGENCY APPROVALS UL60950-1, C-UL, EN60950-1 CASE SIZE/WEIGHT 25.4X9.9X50.8mm (WXHXD) / 40g max COOLING METHOD Convection/Forced air Single output +10V, +24V, +30V with no use of COM. Rated input 12V, 24V or 48V DC lo=100% Symmetrical loading from 5% to 100%. Symmetrical loading from 20% to 100%. Refer to the instruction manual 11. Ripple and Ripple Noise is measured by using test board with in 50mm from output pin terminals. *7 *8 * Drift is the DC output accuracy for eight hours period after a half-hour warm-up at 25C. Rated input voltage (DC24V, DC48V), rated output wattage, ambient temperature at 25C. Parallel operation with other model is not possible. MGFW30 External view Name Plate ¶Recommended Pad and Hole dia. (TOP VIEW) 3.5 9.9 6-f1.5 f 1 ±0.1 ¶ Unit : 0.1inch ¶ Dimension : mm +Vout 10.16 5.08 +Vin -Vin 25.4 10.16 10.16 COM RC 5.08 -Vout ¶ Tolerance ±0.5 ¶ Dimensions in mm ¶ Pin terminal material : Copper ¶ Plating treatment of terminal : Lead free plating ¶ Case material : Brass ¶ Plating treatment of case : Nickel plating ¶ Please keep enough creepage distance with the pattern on PCB and other components. ¶ Mass 40g or less 45.72 50.8 18 Head Office COSEL CO., LTD. 1-6-43 Kamiakae-machi, Toyama 930-0816, Japan Phone:+81-764-32-8152 F a x :+81-764-42-9660 e-mail:[email protected] URL http://www.cosel.co.jp/en Overseas Sales Network AMERICA COSEL U.S.A., INC. 1546 Montague Expressway, San Jose, CA95131 U.S.A. Phone:+1-408-980-5144 Phone(Free):+1-800-888-3526 F a x :+1-408-980-9754 e-mail:[email protected] URL http://www.coselusa.com <Engineering and Technical Support> Phone(Free):+1-866-921-0968 e-mail:[email protected] EUROPE COSEL EUROPE GmbH Berner Str. 51 60437 Frankfurt am Main, Germany Phone:+49-69-95 00 79-0 F a x :+49-69-50 83 02 00 e-mail:[email protected] URL http://www.coseleurope.eu ASIA COSEL ASIA LTD. Rm. 601, 9 Chong Yip Street Kwun Tong, Kowloon, Hong Kong Phone:+852-2305-2712 F a x :+852-2305-3006 e-mail:[email protected] URL http://www.coselasia.com COSEL (SHANGHAI) ELECTRONICS CO., LTD. Room 3F2, Zhao Feng Universe Building, 1800 Zhong Shan West Road, Shanghai, 200235, P.R.China Phone:+86-21-6440-0381 F a x :+86-21-6440-0380 e-mail:[email protected] URL http://www.coselasia.com