Package Information Vishay Siliconix PowerPAKr MLP44-16 (POWER IC ONLY) JEDEC Part Number: MO-220 D -B- ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ Index Area (Dń2 Eń2) 4 D/2 AA E/2 BB E -A- aaa C 2 X Detail A Top View // ccc C Nx 9 CC DD aaa C 2 X Seating Plane 0.08 C -C- Side View A A1 A3 D2 N L Detail B D2/2 Datum A or B N r E2/2 6 (NE-1) x e E2 2 Terminal Tip 1 Exposed Pad N b N N-1 Detail A e/2 5 Terminal Tip 5 e Even Terminal/Side 8 e 5 bbb M C A B (ND-1) x e 8 Odd Terminal/Side Detail B Bottom View Document Number: 72802 16-May-05 www.vishay.com 1 Package Information Vishay Siliconix PowerPAKr MLP44-16 (Power IC Only) JEDEC Part Number: MO-220 MILLIMETERS* Dim Min Nom A 0.80 0.90 A1 0 0.02 A3 − 0.20 Ref AA − 0.345 aaa − 0.15 BB − 0.345 b 0.25 0.30 bbb − 0.10 CC − 0.18 ccc − 0.10 D 4.00 BSC D2 2.55 2.7 DD − 0.18 E 4.00 BSC E2 2.55 2.7 e 0.65 BSC L 0.3 0.4 N 16 ND − 4 NE − 4 r b(min)/2 − * Use millimeters as the primary measurement. INCHES Max Min Nom Max 1.00 0.05 − − − − 0.35 − − − 0.0315 0 − − − − 0.0098 − − − 0.0394 0.0020 − − − − 0.138 − − − 2.8 − 0.1004 − 2.8 0.1004 0.5 0.0118 − − − − − b(min)/2 0.0354 0.0008 0.0079 0.0136 0.0059 0.0136 0.0118 0.0039 0.0071 0.0039 0.1575 BSC 0.1063 0.0071 0.1575 BSC 0.1063 0.0256 BSC 0.0157 16 4 4 − Notes 5 0.1102 − 0.1102 0.0197 − − − 3, 7 6 6 ECN: S-50794—Rev. B, 16-May-05 DWG: 5905 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 2. All dimensions are in millimeters. All angels are in degrees. 3. N is the total number of terminals. 4. The terminal #1 identifier and terminal numbering convention shall conform to JESD 95-1 SPP-012. Details of terminal #1 identifier are optional, but must be located within the zone indicated. The terminal #1 identifier may be either a molded or marked feature. The X and Y dimension will vary according to lead counts. 5. Dimension b applies to metallized terminal and is measured between 0.25 mm and 0.30 mm from the terminal tip. 6. ND and NE refer to the number of terminals on the D and E side respectively. 7. Depopulation is possible in a symmetrical fashion. 8. Variation HHD is shown for illustration only. 9. Coplanarity applies to the exposed heat sink slug as well as the terminals. www.vishay.com 2 Document Number: 72802 16-May-05