AD OP113

Low Noise, Low Drift
Single-Supply Operational Amplifiers
OP113/OP213/OP413
PIN CONFIGURATIONS
NULL
1
–IN A
2
+IN A
3
V–
4
OP113
TOP VIEW
(Not to Scale)
8
NC
OUT A
1
7
V+
–IN A
2
6
OUT A
+IN A
3
5
NULL
V–
4
NC = NO CONNECT
Figure 1. 8-Lead Narrow-Body
SOIC_N
OP213
TOP VIEW
(Not to Scale)
8
V+
7
OUT B
6
–IN B
5
+IN B
00286-002
Single- or dual-supply operation
Low noise: 4.7 nV/√Hz @ 1 kHz
Wide bandwidth: 3.4 MHz
Low offset voltage: 100 μV
Very low drift: 0.2 μV/°C
Unity gain stable
No phase reversal
00286-001
FEATURES
Figure 2. 8-Lead Narrow-Body
SOIC_N
GENERAL DESCRIPTION
The OPx13 family of single-supply operational amplifiers
features both low noise and drift. It has been designed for
systems with internal calibration. Often these processor-based
systems are capable of calibrating corrections for offset and
gain, but they cannot correct for temperature drifts and noise.
Optimized for these parameters, the OPx13 family can be used
to take advantage of superior analog performance combined
with digital correction. Many systems using internal calibration
operate from unipolar supplies, usually either 5 V or 12 V. The
OPx13 family is designed to operate from single supplies from
4 V to 36 V and to maintain its low noise and precision
performance.
The OPx13 family is unity gain stable and has a typical gain
bandwidth product of 3.4 MHz. Slew rate is in excess of 1 V/μs.
Noise density is a very low 4.7 nV/√Hz, and noise in the 0.1 Hz
to 10 Hz band is 120 nV p-p. Input offset voltage is guaranteed
and offset drift is guaranteed to be less than 0.8 μV/°C. Input
common-mode range includes the negative supply and to
within 1 V of the positive supply over the full supply range.
Phase reversal protection is designed into the OPx13 family for
cases where input voltage range is exceeded. Output voltage
swings also include the negative supply and go to within 1 V of
the positive rail. The output is capable of sinking and sourcing
current throughout its range and is specified with 600 Ω loads.
OUT A
1
–IN A
2
+IN A
V–
3
4
OP213
8
V+
7
OUT B
6
5
–IN B
+IN B
OUT A
1
16
OUT D
–IN A
2
15
–IN D
+IN A
3
14
+IN D
V+
4
13
V–
+IN B
5
12
+IN C
–IN B
6
11
–IN C
OUT B
7
10
OUT C
NC
8
9
NC
OP413
TOP VIEW
(Not to Scale)
NC = NO CONNECT
Figure 3. 8-Lead PDIP
Figure 4. 16-Lead Wide-Body
SOIC_W
Digital scales and other strain gage applications benefit from
the very low noise and low drift of the OPx13 family. Other
applications include use as a buffer or amplifier for both analogto-digital (ADC) and digital-to-analog (DAC) sigma-delta
converters. Often these converters have high resolutions
requiring the lowest noise amplifier to utilize their full
potential. Many of these converters operate in either singlesupply or low-supply voltage systems, and attaining the greater
signal swing possible increases system performance.
The OPx13 family is specified for single 5 V and dual ±15 V
operation over the XIND—extended industrial temperature
range (–40°C to +85°C). They are available in PDIP and SOIC
surface-mount packages.
Rev. F
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©1993–2007 Analog Devices, Inc. All rights reserved.
00286-004
Digital scales
Multimedia
Strain gages
Battery-powered instrumentation
Temperature transducer amplifier
00286-003
APPLICATIONS
OP113/OP213/OP413
TABLE OF CONTENTS
Features .............................................................................................. 1
A Low Voltage, Single Supply Strain Gage Amplifier............ 14
Applications....................................................................................... 1
General Description ......................................................................... 1
A High Accuracy Linearized RTD Thermometer
Amplifier ..................................................................................... 14
Pin Configurations ........................................................................... 1
A High Accuracy Thermocouple Amplifier........................... 15
Revision History ............................................................................... 2
An Ultralow Noise, Single Supply Instrumentation
Amplifier ..................................................................................... 15
Specifications..................................................................................... 3
Electrical Characteristics............................................................. 3
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Typical Performance Characteristics ............................................. 7
Applications..................................................................................... 13
Phase Reversal............................................................................. 13
OP113 Offset Adjust .................................................................. 13
Supply Splitter Circuit................................................................ 15
Low Noise Voltage Reference.................................................... 16
5 V Only Stereo DAC for Multimedia ..................................... 16
Low Voltage Headphone Amplifiers........................................ 17
Low Noise Microphone Amplifier for Multimedia ............... 17
Precision Voltage Comparator.................................................. 17
Outline Dimensions ....................................................................... 19
Ordering Guide .......................................................................... 20
Application Circuits ....................................................................... 14
A High Precision Industrial Load-Cell Scale Amplifier........ 14
REVISION HISTORY
3/07—Rev. E to Rev. F
Updated Format..................................................................Universal
Changes to Pin Configurations....................................................... 1
Changes to Absolute Maximum Ratings Section......................... 6
Deleted Spice Model....................................................................... 15
Updated Outline Dimensions ....................................................... 19
Changes to Ordering Guide .......................................................... 20
8/02—Rev. D to Rev. E
Edits to Figure 6 .............................................................................. 13
Edits to Figure 7 .............................................................................. 13
Edits to OUTLINE DIMENSIONS .............................................. 16
9/01—Rev. C to Rev. E
Edits to ORDERING GUIDE.......................................................... 4
Rev. F | Page 2 of 24
OP113/OP213/OP413
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
@ VS = ±15.0 V, TA = 25°C, unless otherwise noted.
Table 1.
E Grade
Parameter
Symbol
Conditions
INPUT CHARACTERISTICS
Offset Voltage
VOS
OP113
−40°C ≤ TA ≤ +85°C
OP213
−40°C ≤ TA ≤ +85°C
OP413
−40°C ≤ TA ≤ +85°C
VCM = 0 V
−40°C ≤ TA ≤ +85°C
VCM = 0 V
−40°C ≤ TA ≤ +85°C
Input Bias Current
IB
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection
VCM
CMR
Large-Signal Voltage Gain
AVO
Long-Term Offset Voltage1
Offset Voltage Drift2
OUTPUT CHARACTERISTICS
Output Voltage Swing High
VOH
VOL
Short-Circuit Limit
POWER SUPPLY
Power Supply Rejection Ratio
ISC
Supply Voltage Range
−15 V ≤ VCM ≤ +14 V
−15 V ≤ VCM ≤ +14 V,
−40°C ≤ TA ≤ +85°C
OP113, OP213,
RL = 600 Ω,
−40°C ≤ TA ≤ +85°C
OP413, RL = 1 kΩ,
−40°C ≤ TA ≤ +85°C
RL = 2 kΩ,
−40°C ≤ TA ≤ +85°C
PSRR
ISY
VS
Typ
240
Min
Max
Unit
150
225
250
325
275
350
600
700
μV
μV
μV
μV
μV
μV
nA
nA
50
+14
nA
V
dB
116
−15
96
97
116
94
dB
1
2.4
1
V/μV
1
2.4
1
V/μV
2
8
2
150
0.8
14
300
1.5
14
13.9
V/μV
μV
μV/°C
V
13.9
−14.5
−14.5
−14.5
−14.5
±40
VS = ±2 V to ±18 V
VS = ±2 V to ±18 V
−40°C ≤ TA ≤ +85°C
VOUT = 0 V, RL = ∞,
VS = ±18 V
−40°C ≤ TA ≤ +85°C
Typ
75
125
100
150
125
175
600
700
50
+14
0.2
RL = 2 kΩ
RL = 2 kΩ,
−40°C ≤ TA ≤ +85°C
RL = 2 kΩ
RL = 2 kΩ,
−40°C ≤ TA ≤ +85°C
F Grade
Max
−15
100
VOS
ΔVOS/ΔT
Output Voltage Swing Low
Supply Current/Amplifier
Min
±40
V
V
V
mA
103
120
100
dB
100
120
97
dB
4
Rev. F | Page 3 of 24
3
3.8
±18
4
3
3.8
±18
mA
mA
V
OP113/OP213/OP413
Parameter
Symbol
AUDIO PERFORMANCE
THD + Noise
Voltage Noise Density
Current Noise Density
Voltage Noise
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
Channel Separation
Settling Time
1
2
en
in
en p-p
SR
GBP
tS
Conditions
Min
VIN = 3 V rms, RL = 2 kΩ,
f = 1 kHz
f = 10 Hz
f = 1 kHz
f = 1 kHz
0.1 Hz to 10 Hz
RL = 2 kΩ
E Grade
Typ
Max
Min
0.0009
9
4.7
0.4
120
0.8
VOUT = 10 V p-p
RL = 2 kΩ, f = 1 kHz
to 0.01%, 0 V to 10 V step
1.2
3.4
0.8
105
9
F Grade
Typ
Max
Unit
0.0009
9
4.7
0.4
120
%
nV/√Hz
nV/√Hz
pA/√Hz
nV p-p
1.2
3.4
V/μs
MHz
105
9
dB
μs
Long-term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at 125°C, with an LTPD of 1.3.
Guaranteed specifications, based on characterization data.
@ VS = 5.0 V, TA = 25°C, unless otherwise noted.
Table 2.
Parameter
Symbol
Conditions
INPUT CHARACTERISTICS
Offset Voltage
VOS
OP113
−40°C ≤ TA ≤ +85°C
OP213
−40°C ≤ TA ≤ +85°C
OP413
−40°C ≤ TA ≤ +85°C
VCM = 0 V, VOUT = 2
−40°C ≤ TA ≤ +85°C
VCM = 0 V, VOUT = 2
−40°C ≤ TA ≤ +85°C
Input Bias Current
IB
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection
VCM
CMR
Large-Signal Voltage Gain
AVO
Long-Term Offset Voltage1
VOS
Offset Voltage Drift2
∆VOS/∆T
0 V ≤ VCM ≤ 4 V
0 V ≤ VCM ≤ 4 V,
−40°C ≤ TA ≤ +85°C
OP113, OP213,
RL = 600 Ω, 2 kΩ,
0.01 V ≤ VOUT ≤ 3.9 V
OP413, RL = 600, 2 kΩ,
0.01 V ≤ VOUT ≤ 3.9 V
Min
E Grade
Typ
Max
F Grade
Typ
Max
Unit
125
175
150
225
175
250
650
750
175
250
300
375
325
400
650
750
μV
μV
μV
μV
μV
μV
nA
nA
50
4
50
4
90
nA
V
dB
90
87
dB
2
2
V/μV
300
0
93
106
1
1
0.2
Rev. F | Page 4 of 24
Min
200
350
V/μV
μV
1.0
1.5
μV/°C
OP113/OP213/OP413
E Grade
Typ
Max
Symbol
Conditions
Min
OUTPUT CHARACTERISTICS
Output Voltage Swing High
VOH
RL = 600 kΩ
RL = 100 kΩ,
−40°C ≤ TA ≤ +85°C
RL = 600 Ω,
−40°C ≤ TA ≤ +85°C
RL = 600 Ω,
−40°C ≤ TA ≤ +85°C
RL = 100 kΩ,
−40°C ≤ TA ≤ +85°C
4.0
4.0
V
4.1
4.1
V
3.9
3.9
V
Output Voltage Swing Low
Short-Circuit Limit
POWER SUPPLY
Supply Current
AUDIO PERFORMANCE
THD + Noise
Voltage Noise Density
Current Noise Density
Voltage Noise
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
Settling Time
1
2
VOL
8
VOUT = 2.0 V, no load
ISY
–40°C ≤ TA ≤ +85°C
en
in
en p-p
SR
GBP
tS
1.6
VOUT = 0 dBu, f = 1 kHz
f = 10 Hz
f = 1 kHz
f = 1 kHz
0.1 Hz to 10 Hz
RL = 2 kΩ
8
±30
0.9
3.5
5.8
mV
mV
mA
2.7
mA
3.0
3.0
mA
0.001
9
4.7
0.45
120
%
nV/√Hz
nV/√Hz
pA/√Hz
nV p-p
3.5
5.8
V/μs
MHz
μs
0.6
Long-term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at 125°C, with an LTPD of 1.3.
Guaranteed specifications, based on characterization data.
Rev. F | Page 5 of 24
Unit
2.7
0.001
9
4.7
0.45
120
0.6
to 0.01%, 2 V step
8
8
±30
ISC
ISY
Min
F Grade
Typ
Max
Parameter
OP113/OP213/OP413
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 3.
Parameter
Supply Voltage
Input Voltage
Differential Input Voltage
Output Short-Circuit Duration to GND
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature Range (Soldering, 60 sec)
Rating
±18 V
±18 V
±10 V
Indefinite
−65°C to +150°C
−40°C to +85°C
−65°C to +150°C
300°C
Table 4. Thermal Resistance
Package Type
θJA
θJC
Unit
8-Lead PDIP (P)
8-Lead SOIC_N (S)
16-Lead SOIC_W (S)
103
158
92
43
43
27
°C/W
°C/W
°C/W
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. F | Page 6 of 24
OP113/OP213/OP413
TYPICAL PERFORMANCE CHARACTERISTICS
100
150
VS = ±15V
TA = 25°C
400 × OP AMPS
PLASTIC PACKAGE
80
VS = ±15V
–40°C ≤ TA ≤ +85°C
400 × OP AMPS
PLASTIC PACKAGE
120
60
60
20
30
00286-005
40
0
–50
–40
–30 –20 –10
0
10
20
30
INPUT OFFSET VOLTAGE, VOS (µV)
40
0
50
Figure 5. OP113 Input Offset (VOS) Distribution @ ±15 V
0
0.1
0.2
0.3
0.4
0.5
0.6
TCVOS (µV)
0.7
0.8
0.9
1.0
Figure 8. OP113 Temperature Drift (TCVOS) Distribution @ ±15 V
500
500
VS = ±15V
TA = 25°C
896 × OP AMPS
PLASTIC PACKAGE
400
00286-008
UNITS
UNITS
90
VS = ±15V
–40°C ≤ TA ≤ +85°C
896 × OP AMPS
PLASTIC PACKAGE
400
300
200
100
100
0
–100
00286-006
200
–80
–60
–40
–20
0
20
40
60
80
0
100
00286-009
UNITS
UNITS
300
0
0.1
0.2
0.3
INPUT OFFSET VOLTAGE, VOS (µV)
Figure 6. OP213 Input Offset (VOS) Distribution @ ±15 V
0.7
0.8
0.9
1.0
Figure 9. OP213 Temperature Drift (TCVOS) Distribution @ ±15 V
500
400
0.4
0.5
0.6
TCVOS (µV)
600
VS = ±15V
TA = 25°C
1220 × OP AMPS
PLASTIC PACKAGE
VS = ±15V
–40°C ≤ TA ≤ +85°C
1220 × OP AMPS
PLASTIC PACKAGE
500
400
UNITS
UNITS
300
300
200
200
100
–40
–20
0
20
40
60
80
100
INPUT OFFSET VOLTAGE, VOS (µV)
120
0
140
Figure 7. OP413 Input Offset (VOS) Distribution @ ±15 V
00286-010
00286-007
0
–60
100
0
0.1
0.2
0.3
0.4
0.5
0.6
TCVOS (µV)
0.7
0.8
0.9
1.0
Figure 10. OP413 Temperature Drift (TCVOS) Distribution @ ±15 V
Rev. F | Page 7 of 24
OP113/OP213/OP413
800
400
INPUT BIAS CURRENT (nA)
500
VCM = 0V
600
VS = +5V
VCM = +2.5V
VS = ±15V
VCM = 0V
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
0
–75
125
5.0
1.0
3.5
0.5
–SWING
RL = 600Ω
–25
0
25
50
TEMPERATURE (°C)
75
POSITIVE OUTPUT SWING (V)
–SWING
RL = 2kΩ
NEGATIVE OUTPUT SWING (mV)
+SWING
RL = 2kΩ
100
0
125
+SWING
RL = 2kΩ
13.5
+SWING
RL = 600Ω
13.0
12.5
–SWING
RL = 2kΩ
–13.5
–SWING
RL = 600Ω
–14.0
–15.0
–75
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
125
20
VS = ±15V
TA = 25°C
VS = 5V
VO = 3.9V
18
20
OPEN-LOOP GAIN (V/µV)
16
0
–20
–40
–60
–80
–100
100
1k
10k
100k
FREQUENCY (Hz)
RL = 2kΩ
14
12
10
8
RL = 600Ω
6
4
105
–120
10
125
Figure 15. Output Swing vs. Temperature and RL @ ±15 V
00286-013
CHANNEL SEPARATION (dB)
40
100
14.0
Figure 12. Output Swing vs. Temperature and RL @ 5 V
60
75
–14.5
00286-012
POSITIVE OUTPUT SWING (V)
1.5
–50
VS = ±15V
14.5
4.5
3.0
–75
0
25
50
TEMPERATURE (°C)
15.0
2.0
VS = 5V
+SWING
RL = 600Ω
–25
–50
Figure 14. OP213 Input Bias Current vs. Temperature
Figure 11. OP113 Input Bias Current vs. Temperature
4.0
00286-014
0
–75
200
100
00286-011
200
VS = ±15V
00286-015
400
VS = +5V
300
1M
00286-016
INPUT BIAS CURRENT (nA)
1000
2
0
–75
10M
Figure 13. Channel Separation
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
Figure 16. Open-Loop Gain vs. Temperature @ 5 V
Rev. F | Page 8 of 24
125
OP113/OP213/OP413
12.5
10
VS = ±15V
VD = ±10V
RL = 2kΩ
10.0
8
OPEN-LOOP GAIN (V/µV)
7.5
RL = 1kΩ
5.0
RL = 600Ω
2.5
RL = 2kΩ
7
6
5
4
3
RL = 600Ω
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
1
0
–75
125
–25
0
25
50
TEMPERATURE (°C)
75
125
100
100
V+ = 5V
V– = 0V
TA = 25°C
80
45
GAIN
40
90
PHASE
θm = 57°
20
135
10k
100k
FREQUENCY (Hz)
225
10M
1M
00286-018
–20
1k
40
20
135
180
10k
100k
FREQUENCY (Hz)
225
10M
1M
Figure 21. Open-Loop Gain, Phase vs. Frequency @ ±15 V
50
TA = 25°C
VS = ±15V
40
AV = 100
CLOSED-LOOP GAIN (dB)
AV = 100
30
20
AV = 10
10
0
AV = 1
10k
100k
FREQUENCY (Hz)
1M
30
20
AV = 10
10
0
AV = 1
–10
00286-019
–10
–20
1k
θm = 72°
–20
1k
V+ = 5V
V– = 0V
TA = 25°C
40
90
PHASE
Figure 18. Open-Loop Gain, Phase vs. Frequency @ 5 V
50
45
GAIN
0
180
0
60
–20
1k
10M
10k
100k
FREQUENCY (Hz)
1M
Figure 22. Closed-Loop Gain vs. Frequency @ ±15 V
Figure 19. Closed-Loop Gain vs. Frequency @ 5 V
Rev. F | Page 9 of 24
PHASE (Degrees)
60
0
10M
00286-021
0
OPEN-LOOP GAIN (dB)
80
TA = 25°C
VS = ±15V
PHASE (Degrees)
100
OPEN-LOOP GAIN (dB)
–50
Figure 20. OP213 Open-Loop Gain vs. Temperature
Figure 17. OP413 Open-Loop Gain vs. Temperature
CLOSED-LOOP GAIN (dB)
00286-020
0
–75
00286-017
2
00286-052
OPEN-LOOP GAIN (V/µV)
VS = ±15V
VO = ±10V
9
OP113/OP213/OP413
70
70
5
5
3
θm
2
55
50
–75
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
1
125
Figure 23. Gain Bandwidth Product and Phase Margin vs. Temperature @ 5 V
4
GBW
θm
60
3
55
2
50
–75
–50
–25
0
25
50
TEMPERATURE (°C)
75
TA = 25°C
VS = ±15V
20
15
10
5
1
10
100
2.5
2.0
1.5
1.0
0.5
0
1k
00286-026
CURRENT NOISE DENSITY (pA/ Hz)
25
00286-023
VOLTAGE NOISE DENSITY (nV/ Hz)
1
125
3.0
TA = 25°C
VS = ±15V
1
10
FREQUENCY (Hz)
Figure 27. Current Noise Density vs. Frequency
140
V+ = 5V
V– = 0V
TA = 25°C
100
80
60
40
00286-024
20
10k
FREQUENCY (Hz)
100k
TA = 25°C
VS = ±15V
120
COMMON-MODE REJECTION (dB)
120
1k
1k
100
80
60
40
20
0
100
1M
Figure 25. Common-Mode Rejection vs. Frequency @ 5 V
00286-027
140
0
100
100
FREQUENCY (Hz)
Figure 24. Voltage Noise Density vs. Frequency
COMMON-MODE REJECTION (dB)
100
Figure 26. Gain Bandwidth Product and Phase Margin vs. Temperature @ ±15 V
30
0
GAIN BANDWIDTH PRODUCT (MHz)
GBW
60
65
00286-025
4
PHASE MARGIN (Degrees)
65
GAIN BANDWIDTH PRODUCT (MHz)
VS = ±15V
00286-022
PHASE MARGIN (Degrees)
V+ = 5V
V– = 0V
1k
10k
FREQUENCY (Hz)
100k
1M
Figure 28. Common-Mode Rejection vs. Frequency @ ±15 V
Rev. F | Page 10 of 24
OP113/OP213/OP413
40
120
30
100
IMPEDANCE (Ω)
+PSRR
80
60
–PSRR
40
AV = 100
AV = 10
20
1k
10k
FREQUENCY (Hz)
100k
0
100
1M
10k
100k
1M
FREQUENCY (Hz)
Figure 32. Closed-Loop Output Impedance vs. Frequency @ ±15 V
30
6
VS = 5V
RL = 2kΩ
TA = 25°C
AVCL = 1
VS = ±15V
RL = 2kΩ
TA = 25°C
AVOL = 1
25
MAXIMUM OUTPUT SWING (V)
5
4
3
2
20
15
10
00286-029
0
1k
10k
100k
FREQUENCY (Hz)
1M
0
1k
10M
00286-032
5
1
10k
100k
FREQUENCY (Hz)
1M
10M
Figure 33. Maximum Output Swing vs. Frequency @ ±15 V
Figure 30. Maximum Output Swing vs. Frequency @ 5 V
20
50
VS = 5V
RL = 2kΩ
VIN = 100mV p-p
TA = 25°C
AVCL = 1
35
16
14
30
NEGATIVE
EDGE
25
20
POSITIVE
EDGE
15
12
8
6
5
2
00286-030
4
100
200
300
LOAD CAPACITANCE (pF)
400
NEGATIVE
EDGE
10
10
0
POSITIVE
EDGE
0
500
00286-033
40
VS = ±15V
RL = 2kΩ
VIN = 100mV p-p
TA = 25°C
AVCL = 1
18
OVERSHOOT (%)
45
0
1k
00286-031
AV = 1
Figure 29. Power Supply Rejection vs. Frequency @ ±15 V
MAXIMUM OUTPUT SWING (V)
20
10
0
100
OVERSHOOT (%)
TA = 25°C
VS = ±15V
TA = 25°C
VS = ±15V
00286-028
POWER SUPPLY REJECTION (dB)
140
0
100
200
300
LOAD CAPACITANCE (pF)
400
500
Figure 34. Small-Signal Overshoot vs. Load Capacitance @ ±15 V
Figure 31. Small-Signal Overshoot vs. Load Capacitance @ 5 V
Rev. F | Page 11 of 24
OP113/OP213/OP413
2.0
VS = 5V
0.5V ≤ VOUT ≤ 4.0V
VS = ±15V
–10V ≤ VOUT ≤ +10V
1.5
+SLEW RATE
SLEW RATE (V/µs)
SLEW RATE (V/µs)
1.5
1.0
–SLEW RATE
0.5
–SLEW RATE
1.0
0.5
00286-034
0
–75
+SLEW RATE
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
0
–75
125
Figure 35. Slew Rate vs. Temperature @ 5 V (0.5 V ≤ VOUT ≤ 4.0 V)
00286-037
2.0
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
125
Figure 38. Slew Rate vs. Temperature @ ±15 V (–10 V ≤ VOUT ≤ +10.0 V)
1s
1s
100
100
90
90
10
10
0%
20mV
00286-038
00286-035
0%
20mV
Figure 36. Input Voltage Noise @ ±15 V (20 nV/div)
Figure 39. Input Voltage Noise @ 5 V (20 nV/div)
5
100Ω
AV = 100
tOUT
00286-036
0.1Hz TO 10Hz
AV = 1000
VS = ±18V
VS = +5V
2
1
0
–75
Figure 37. Noise Test Diagram
VS = ±15V
3
00286-039
909Ω
SUPPLY CURRENT (mA)
4
–50
–25
0
25
50
TEMPERATURE (°C)
75
Figure 40. Supply Current vs. Temperature
Rev. F | Page 12 of 24
100
125
OP113/OP213/OP413
APPLICATIONS
The OP113, OP213, and OP413 form a new family of high
performance amplifiers that feature precision performance in
standard dual-supply configurations and, more importantly,
maintain precision performance when a single power supply is
used. In addition to accurate dc specifications, it is the lowest
noise single-supply amplifier available with only 4.7 nV/√Hz
typical noise density.
Single-supply applications have special requirements due to the
generally reduced dynamic range of the output signal. Singlesupply applications are often operated at voltages of 5 V or 12 V,
compared to dual-supply applications with supplies of ±12 V or
±15 V. This results in reduced output swings. Where a dualsupply application may often have 20 V of signal output swing,
single-supply applications are limited to, at most, the supply
range and, more commonly, several volts below the supply.
In order to attain the greatest swing, the single-supply output
stage must swing closer to the supply rails than in dual-supply
applications.
The OPx13 family has a new patented output stage that allows
the output to swing closer to ground, or the negative supply,
than previous bipolar output stages. Previous op amps had
outputs that could swing to within about 10 mV of the negative
supply in single-supply applications. However, the OPx13
family combines both a bipolar and a CMOS device in the output
stage, enabling it to swing to within a few hundred μV of ground.
When operating with reduced supply voltages, the input range
is also reduced. This reduction in signal range results in
reduced signal-to-noise ratio for any given amplifier. There are
only two ways to improve this: increase the signal range or
reduce the noise. The OPx13 family addresses both of these
parameters. Input signal range is from the negative supply to
within 1 V of the positive supply over the full supply range.
Competitive parts have input ranges that are 0.5 V to 5 V less
than this. Noise has also been optimized in the OPx13 family.
At 4.7 nV/√Hz, the noise is less than one fourth that of competitive
devices.
PHASE REVERSAL
The OPx13 family is protected against phase reversal as long as
both of the inputs are within the supply ranges. However, if
there is a possibility of either input going below the negative
supply (or ground in the single-supply case), the inputs should
be protected with a series resistor to limit input current to 2 mA.
OP113 OFFSET ADJUST
The OP113 has the facility for external offset adjustment, using
the industry standard arrangement. Pin 1 and Pin 5 are used in
conjunction with a potentiometer of 10 kΩ total resistance,
connected with the wiper to V− (or ground in single-supply
applications). The total adjustment range is about ±2 mV using
this configuration.
Adjusting the offset to 0 has minimal effect on offset drift
(assuming the potentiometer has a tempco of less than
1000 ppm/°C). Adjustment away from 0, however, (as with all
bipolar amplifiers) results in a TCVOS of approximately
3.3 μV/°C for every millivolt of induced offset.
It is, therefore, not generally recommended that this trim be
used to compensate for system errors originating outside of the
OP113. The initial offset of the OP113 is low enough that
external trimming is almost never required, but if necessary, the
2 mV trim range may be somewhat excessive. Reducing the
trimming potentiometer to a 2 kΩ value results in a more
reasonable range of ±400 μV.
Rev. F | Page 13 of 24
OP113/OP213/OP413
APPLICATION CIRCUITS
5V
A HIGH PRECISION INDUSTRIAL LOAD-CELL
SCALE AMPLIFIER
2
The OPx13 family makes an excellent amplifier for
conditioning a load-cell bridge. Its low noise greatly improves
the signal resolution, allowing the load cell to operate with a
smaller output range, thus reducing its nonlinearity. Figure 41
shows one half of the OPx13 family used to generate a very
stable 10 V bridge excitation voltage while the second amplifier
provides a differential gain. R4 should be trimmed for
maximum common-mode rejection.
+15V
+10V
8
1
1/2
+ 3
A2
– 2
R3
17.2kΩ
0.1%
350Ω
LOAD
CELL
100mV
F.S.
13
R4
500Ω
A1
OP213
R1
100kΩ
7
OUTPUT
0
10V
FS
00286-040
R2
301Ω
0.1%
5V
R7
20kΩ
1
OUTPUT
0V 3.5V
8
1/2
7
4
R3
20kΩ
R4
100kΩ
R2
20kΩ
R5
2.1kΩ
R6
27.4Ω
RG = 2127.4Ω
Figure 42. Single Supply Strain Gage Amplifier
A HIGH ACCURACY LINEARIZED RTD
THERMOMETER AMPLIFIER
–15V
R1
17.2kΩ
0.1%
1/2
OP213
8
CMRR TRIM
10-TURN
T.C. LESS THAN 50ppm/°C
7
1/2
4
4
– 2
3 +
+ 10µF
6 –
5 +
11 12
4
OP295
10
6
GND
15
AD588BQ
4
+10V
REF43
6 OUT
6 –
2 –
9
OP213
2.5V
OP295
R8
12kΩ
14
3
+ 3
5 +
16
1
1/2
4V
350Ω
35mV
FS
–15V
2
1
00286-041
2N2219A
R5
1kΩ
8
2N2222A
IN
Figure 41. Precision Load-Cell Scale Amplifier
A LOW VOLTAGE, SINGLE SUPPLY STRAIN GAGE
AMPLIFIER
The true zero swing capability of the OPx13 family allows the
amplifier in Figure 42 to amplify the strain gage bridge
accurately even with no signal input while being powered by a
single 5 V supply. A stable 4 V bridge voltage is made possible
by the rail-to-rail OP295 amplifier, whose output can swing to
within a millivolt of either rail. This high voltage swing greatly
increases the bridge output signal without a corresponding
increase in bridge input.
Zero suppressing the bridge facilitates simple linearization of
the resistor temperature device (RTD) by feeding back a small
amount of the output signal to the RTD. In Figure 43, the left
leg of the bridge is servoed to a virtual ground voltage by
Amplifier A1, and the right leg of the bridge is servoed to 0 V
by Amplifier A2. This eliminates any error resulting from
common-mode voltage change in the amplifier. A 3-wire RTD
is used to balance the wire resistance on both legs of the bridge,
thereby reducing temperature mismatch errors. The 5 V bridge
excitation is derived from the extremely stable AD588 reference
device with 1.5 ppm/°C drift performance.
Linearization of the RTD is done by feeding a fraction of the
output voltage back to the RTD in the form of a current. With
just the right amount of positive feedback, the amplifier output
will be linearly proportional to the temperature of the RTD.
Rev. F | Page 14 of 24
OP113/OP213/OP413
16
2
12V
0.1µF
+
2 REF02EZ
4
11
1
6
3
9
8
R9
124kΩ
12V
10µF
+
D1
4
7
R5
40.2kΩ
1N4148
15
R3
50Ω
RG FULL SCALE ADJUST
R2
8.25kΩ
10
+
K-TYPE
THERMOCOUPLE
40.7µV/°C
R5
R7
4.02kΩ 100Ω
R1
8.25kΩ
–
–
+
+
+15V
RW1
6 –
R4
100Ω
7
1/2
OP213
–15V
RW3
R8
49.9kΩ
2 –
A1
3 +
R8
453Ω
R2
2.74kΩ
+
2 –
8
1/2
1
OP213
R6
200Ω
R3
53.6Ω
3 +
0V TO 10V
(0°C TO 1000°C)
4
8
A2
5 + 4
RW2
0.1µF
R4
5.62kΩ
VOUT (10mV/°C)
–1.5V = –150°C
+5V = +500°C
R9
5kΩ
LINEARITY
ADJUST
@1/2 FS
1
00286-042
AD588BQ
13
100Ω
RTD
R1
10.7kΩ
14
12
10µF
5V
6
00286-043
+15V
1/2
OP213
Figure 43. Ultraprecision RTD Amplifier
To calibrate the circuit, first immerse the RTD in a 0°C ice bath
or substitute an exact 100 Ω resistor in place of the RTD. Adjust
the zero adjust potentiometer for a 0 V output, and then set R9,
linearity adjust potentiometer, to the middle of its adjustment
range. Substitute a 280.9 Ω resistor (equivalent to 500°C) in
place of the RTD, and adjust the full-scale adjust potentiometer
for a full-scale voltage of 5 V.
Figure 44. Accurate K-Type Thermocouple Amplifier
R6 should be adjusted for a 0 V output with the thermocouple
measuring tip immersed in a 0°C ice bath. When calibrating, be
sure to adjust R6 initially to cause the output to swing in the
positive direction first. Then back off in the negative direction
until the output just stops changing.
AN ULTRALOW NOISE, SINGLE SUPPLY
INSTRUMENTATION AMPLIFIER
Extremely low noise instrumentation amplifiers can be built
using the OPx13 family. Such an amplifier that operates from a
single supply is shown in Figure 45. Resistors R1 to R5 should
be of high precision and low drift type to maximize CMRR
performance. Although the two inputs are capable of operating
to 0 V, the gain of −100 configuration limits the amplifier input
common-mode voltage to 0.33 V.
5V TO 36V
To calibrate out the nonlinearity, substitute a 194.07 Ω resistor
(equivalent to 250°C) in place of the RTD, and then adjust the
linearity adjust potentiometer for a 2.5 V output. Check and
readjust the full-scale and half-scale as needed.
+
1/2
OP213
–
+
VOUT
–
1/2
OP213
Once calibrated, the amplifier outputs a 10 mV/°C temperature
coefficient with an accuracy better than ±0.5°C over an RTD
measurement range of −150°C to +500°C. Indeed the amplifier
can be calibrated to a higher temperature range, up to 850°C.
*R1
10kΩ
–
*R2
10kΩ
*R3
10kΩ
*RG
(200Ω + 12.7Ω)
*ALL RESISTORS ±0.1%, ±25ppm/°C.
A HIGH ACCURACY THERMOCOUPLE AMPLIFIER
Figure 44 shows a popular K-type thermocouple amplifier with
cold-junction compensation. Operating from a single 12 V
supply, the OPx13 family’s low noise allows temperature
measurement to better than 0.02°C resolution over a 0°C to
1000°C range. The cold-junction error is corrected by using an
inexpensive silicon diode as a temperature measuring device.
It should be placed as close to the two terminating junctions as
physically possible. An aluminum block might serve well as an
isothermal system.
+
VIN
*R4
10kΩ
GAIN =
20kΩ
+6
RG
00286-044
–15V
Figure 45. Ultralow Noise, Single Supply Instrumentation Amplifier
SUPPLY SPLITTER CIRCUIT
The OPx13 family has excellent frequency response
characteristics that make it an ideal pseudoground reference
generator, as shown in Figure 46. The OPx13 family serves as a
voltage follower buffer. In addition, it drives a large capacitor
that serves as a charge reservoir to minimize transient load
changes, as well as a low impedance output device at high
frequencies. The circuit easily supplies 25 mA load current with
good settling characteristics.
Rev. F | Page 15 of 24
OP113/OP213/OP413
12V
R3
2.5kΩ
5V
–
10µF
+
5V
R1
5kΩ
–
1/2
OP213
+
R4
100Ω
1
VS+
+
4
2
C2
1µF
OP213
10kΩ
3
+
C2
10µF
REF43
GND
OUTPUT
+
4
The OPx13 family’s low noise and single supply capability are
ideally suited for stereo DAC audio reproduction or sound
synthesis applications such as multimedia systems. Figure 48
shows an 18-bit stereo DAC output setup that is powered from a
single 5 V supply. The low noise preserves the 18-bit dynamic
range of the AD1868. For DACs that operate on dual supplies,
the OPx13 family can also be powered from the same supplies.
Few reference devices combine low noise and high output drive
capabilities. Figure 47 shows the OPx13 family used as a twopole active filter that band limits the noise of the 2.5 V reference.
Total noise measures 3 μV p-p.
5V SUPPLY
AD1868
2
3
4
5
6
7
18-BIT
LL DAC
VBL
V OL
DR
18-BIT
LR SERIAL
REG.
DGND
18-BIT
DAC
8
VBR
220µF
1/2
7.68kΩ
330pF
9.76kΩ
+
OP213
2
–
7.68kΩ
11
7.68kΩ
10
47kΩ
100pF
7.68kΩ
VS
LEFT
CHANNEL
OUTPUT
+ –
100pF
AGND 12
V OR
1
4
13
VREF
+
–
14
8
+
15
VREF
CK
16
3
–
+
18-BIT
DL SERIAL
REG.
3µV p-p NOISE
5 V ONLY STEREO DAC FOR MULTIMEDIA
LOW NOISE VOLTAGE REFERENCE
VL
9
330pF
OUTPUT
2.5V
Figure 47. Low Noise Voltage Reference
Figure 46. False Ground Generator
1
1
4
00286-045
3
10kΩ
OUT 6
8
8
–
1/2
IN
2
R2
5kΩ
2
2
00286-046
C1
0.1µF
9.76kΩ
+
6
–
1/2
OP213
5
+
Figure 48. 5 V Only 18-Bit Stereo DAC
Rev. F | Page 16 of 24
220µF
7
+ –
47kΩ
RIGHT
CHANNEL
OUTPUT
00286-047
VS+ = 5V
OP113/OP213/OP413
10kΩ
LOW VOLTAGE HEADPHONE AMPLIFIERS
5V
Figure 49 shows a stereo headphone output amplifier for the
AD1849 16-bit SOUNDPORT® stereo codec device. 1 The
pseudo-reference voltage is derived from the common-mode
voltage generated internally by the AD1849, thus providing a
convenient bias for the headphone output amplifiers.
10µF
+
10kΩ
1/2
OP213
50Ω
20Ω
17 MINL
+
100Ω
AD1849
5V
5kΩ
1/2
19 CMOUT
–
OP213
+
5V
10µF
–
LOUT1L 31
LEFT
ELECTRET
CONDENSER
MIC
INPUT
L VOLUME
CONTROL
220µF
16Ω +
1/2
OP213
10kΩ
+
20Ω
HEADPHONE
LEFT
47kΩ
RIGHT
ELECTRET
CONDENSER
MIC
INPUT
5V
AD1849
1/2
VREF
10µF
+
–
100Ω
10kΩ
50Ω
+
1/2
OP213
15 MINR
–
10kΩ
00286-049
VREF
OPTIONAL
GAIN
1kΩ
–
Figure 50. Low Noise Stereo Microphone Amplifier for Multimedia Sound
Codec
OP213
+
PRECISION VOLTAGE COMPARATOR
CMOUT 19
–
10kΩ
1/2
OP213
LOUT1R 29
+
5kΩ
OPTIONAL
GAIN
00286-048
1kΩ
HEADPHONE
RIGHT
47kΩ
10µF
R VOLUME
CONTROL
220µF
16Ω +
VREF
Figure 49. Headphone Output Amplifier for Multimedia Sound Codec
LOW NOISE MICROPHONE AMPLIFIER FOR
MULTIMEDIA
The OPx13 family is ideally suited as a low noise microphone
preamp for low voltage audio applications. Figure 50 shows a
gain of 100 stereo preamp for the AD1849 16-bit SOUNDPORT
stereo codec chip. The common-mode output buffer serves as a
phantom power driver for the microphones.
With its PNP inputs and 0 V common-mode capability, the
OPx13 family can make useful voltage comparators. There is
only a slight penalty in speed in comparison to IC comparators.
However, the significant advantage is its voltage accuracy. For
example, VOS can be a few hundred microvolts or less, combined
with CMRR and PSRR exceeding 100 dB, while operating from
a 5 V supply. Standard comparators like the 111/311 family
operate on 5 V, but not with common mode at ground, nor with
offset below 3 mV. Indeed, no commercially available singlesupply comparator has a VOS less than 200 μV.
1
SOUNDPORT is a registered trademark of Analog Devices, Inc.
Rev. F | Page 17 of 24
OP113/OP213/OP413
Figure 51 shows the OPx13 family response to a 10 mV
overdrive signal when operating in open loop. The top trace
shows the output rising edge has a 15 μs propagation delay,
whereas the bottom trace shows a 7 μs delay on the output
falling edge. This ac response is quite acceptable in many
applications.
±10mV OVERDRIVE
5V
The low noise and 250 μV (maximum) offset voltage enhance
the overall dc accuracy of this type of comparator. Note that zerocrossing detectors and similar ground referred comparisons can be
implemented even if the input swings to −0.3 V below ground.
+IN
+2.5V
25kΩ
0V
–2.5V
100Ω
tr = tf = 5ms
2V
+
9V 9V
OUT
1/2
–IN
OP113
–
5µs
00286-051
100
90
Figure 52. OP213 Simplified Schematic
2V
00286-050
10
0%
Figure 51. Precision Comparator
Rev. F | Page 18 of 24
OP113/OP213/OP413
OUTLINE DIMENSIONS
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
8
5
1
4
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.100 (2.54)
BSC
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
070606-A
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 53. 8-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
P-Suffix
(N-8)
Dimensions shown in inches and (millimeters)
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-A A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 54. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
S-Suffix
(R-8)
Dimensions shown in millimeters and (inches)
Rev. F | Page 19 of 24
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
OP113/OP213/OP413
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
45°
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
1.27 (0.0500)
0.40 (0.0157)
030707-B
1
Figure 55. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
S-Suffix
(RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
OP113ES
OP113ES-REEL
OP113ES-REEL7
OP113ESZ1
OP113ESZ-REEL1
OP113ESZ-REEL71
OP113FS
OP113FS-REEL
OP113FS-REEL7
OP113FSZ1
OP113FSZ-REEL1
OP113FSZ-REEL71
OP213ES
OP213ES-REEL
OP213ES-REEL7
OP213ESZ1
OP213ESZ-REEL1
OP213ESZ-REEL71
OP213FP
OP213FPZ1
OP213FS
OP213FS-REEL
OP213FS-REEL7
OP213FSZ1
OP213FSZ-REEL1
OP213FSZ-REEL71
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead PDIP
8-Lead PDIP
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
Rev. F | Page 20 of 24
Package Options
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
N-8 (P-Suffix)
N-8 (P-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
R-8 (S-Suffix)
OP113/OP213/OP413
Model
OP413ES
OP413ES-REEL
OP413ESZ1
OP413ESZ-REEL1
OP413FS
OP413FS-REEL
OP413FSZ1
OP413FSZ-REEL1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
Z = RoHS Compliant Part.
Rev. F | Page 21 of 24
Package Options
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
RW-16 (S-Suffix)
OP113/OP213/OP413
NOTES
Rev. F | Page 22 of 24
OP113/OP213/OP413
NOTES
Rev. F | Page 23 of 24
OP113/OP213/OP413
NOTES
©1993–2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C00286-0-3/07(F)
Rev. F | Page 24 of 24