TI OPA4364AQDRQ1

OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
1.8-V, 7-MHz, 90-dB CMRR, SINGLE-SUPPLY,
RAIL-TO-RAIL I/O OPERATIONAL AMPLIFIER
FEATURES
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
1.8-V Operation
Bandwidth: 7 MHz
CMRR: 90 dB (Typ)
Slew Rate: 5 V/µs
Low Offset: 500 µV (Max)
Quiescent Current: 750 µA/Channel (Max)
Shutdown Mode: <1 µA/Channel
APPLICATIONS
•
•
•
•
•
Signal Conditioning
Data Acquisition
Process Control
Active Filters
Test Equipment
OPA4364...D PACKAGE
(TOP VIEW)
VOUT A
1
14
VOUT D
–In A
2
13
–In D
+In A
3
12
+In D
V+
4
11
V–
+In B
5
10
+In C
–In B
6
9
–In C
VOUT B
7
8
VOUT C
A
B
D
C
OPA2364...D PACKAGE
(TOP VIEW)
VOUT A
1
8
V+
–In A
2
7
VOUT B
+In A
3
6
–In B
V–
4
5
+In B
DESCRIPTION
The OPA2364 and OPA4364 are high-performance CMOS operational amplifiers optimized for low-voltage
single-supply operation. These miniature low-cost amplifiers are designed to operate on single supplies from
1.8 V (±0.9 V) to 5.5 V (±2.75 V). Applications include sensor amplification and signal conditioning in
battery-powered systems.
The OPAx364 family offers excellent CMRR without the crossover associated with traditional complimentary
input stages. This results in excellent performance for driving analog-to-digital (A/D) converters without
degradation of differential linearity and total harmonic distortion (THD). The input common-mode range includes
both the negative and positive supplies. The output voltage swing is within 10 mV of the rails.
The dual version is available in an SO-8 package and the quad package is available in an SO-14 package. All
versions are specified for operation from –40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006, Texas Instruments Incorporated
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
ORDERING INFORMATION
PACKAGE
LEAD
PACKAGE
DESIGNATOR
TA
OPA2364AQDRQ1
SO-8
D
OPA4364AQDRQ1
SO-14
D
PRODUCT
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT MEDIA,
QUANTITY
–40°C to 125°C
OP2364
OPA2364AQDRQ1
Tape and reel, 2500
–40°C to 125°C
OPA4364AQ
OPA4364AQDRQ1
Tape and reel, 2500
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
Supply voltage
Signal input terminals
Voltage range (2)
–0.5
Current (2)
Enable input range
(V–) –0.5
Output short circuit (3)
UNIT
5.5
V
(V+) + 0.5
V
±10
mA
5.5
V
Continuous
Operating temperature range
–40
150
°C
Tstg
Storage temperature range
–65
150
°C
TJ
Junction temperature
150
°C
Lead temperature (soldering, 10 s)
300
°C
(1)
(2)
(3)
2
MAX
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
Input terminals are diode clamped to the power-supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should
be current limited to 10 mA or less.
Short circuit to ground one amplifier per package
Submit Documentation Feedback
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
ELECTRICAL CHARACTERISTICS: VS = 1.8 V to 5.5 V
Boldface limits apply over the specified temperature range, TA = –40°C to 125°C, TA = 25°C, RL = 10 kΩ connected to VS/2,
and VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1
3
UNIT
Offset Voltage
VOS
Input offset voltage
dVOS/dT
Drift
VS = 5 V
PSRR
Power-supply rejection ratio
VS = 1.8 V to 5.5 V, VCM = 0
80
Channel separation, dc
mV
µV/°C
3
330
µV/V
µV/V
1
Input Bias Current
IB
Input bias current
IOS
Input offset current
±1
Over temperature
±10
pA
±10
pA
See Typical Characteristics
±1
Noise
en
in
Input voltage noise
f = 0.1 Hz to 10 Hz
10
µVP-P
Input voltage noise density
f = 10 kHz
17
nV/√Hz
Input current noise density
f = 10 kHz
0.6
fA/√Hz
Input Voltage Range
VCM
Common-mode voltage range
CMRR
Common-mode rejection ratio
(V–) – 0.1
(V–) – 0.1 V < VCM < (V+) + 0.1 V
74
(V+) + 0.1
V
90
dB
Differential
2
pF
Common mode
3
pF
Input Capacitance
Open-Loop Gain
AOL
Open-loop voltage gain
RL = 10 kΩ,
100 mV < VO < (V+) – 100 mV
94
OPA4364A
90
Over temperature,
VS = 1.8 V to 5.5 V
86
100
dB
dB
Frequency Response
GBW
Gain bandwidth product
CL = 100 pF
7
MHz
SR
Slew rate
CL = 100 pF, G = 1
5
V/µs
0.1%
CL = 100 pF, VS = 5 V, 4-V step, G = 1
1
µs
0.01%
CL = 100 pF, VS = 5 V, 4-V step, G = 1
1.5
µs
Overload recovery time
CL = 100 pF, VIN × Gain > VS
0.8
µs
Total harmonic distortion + noise
CL = 100 pF, VS = 5 V, G = 1,
f = 20 Hz to 20 kHz
0.002%
ts
THD+N
Settling time
Output
From rail
Voltage output
swing
Over temperature
RL = 10 kΩ
RL = 10 kΩ
10
20
VOL
20
VOH
40
ISC
Short-circuit current
See Typical Characteristics
CLOAD
Capacitive load drive
See Typical Characteristics
mV
mV
Power Supply
VS
Specified voltage
1.8
Operating voltage
IQ
Quiescent current (per amplifier)
5.5
V
µA
1.8 to 5.5
V
VS = 1.8 V
650
750
VS = 3.6 V
850
1000
µA
VS = 5.5 V
1.1
1.4
mA
Submit Documentation Feedback
3
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
ELECTRICAL CHARACTERISTICS: VS = 1.8 V to 5.5 V (continued)
Boldface limits apply over the specified temperature range, TA = –40°C to 125°C, TA = 25°C, RL = 10 kΩ connected to VS/2,
and VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Temperature Range
θJA
4
Specified range
–40
125
°C
Storage range
–65
150
°C
Thermal
resistance
SO-8
150
SO-14
100
Submit Documentation Feedback
°C/W
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS
At TCASE = 25°C, RL = 10 kΩ, and connected to VS/2, VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
120
0
100
-30
80
-60
60
-90
40
-120
20
-150
0
-180
100
90
CMRR – dB
Phase – °
80
70
60
50
40
30
20
10
-20
10
100
1k
10k 100k 1M
Frequency – Hz
10M
0
100M
10
100
1k
10k
100k
Frequency – Hz
Figure 1.
Figure 2.
POWER-SUPPLY REJECTION RATIO
vs
FREQUENCY
QUIESCENT CURRENT
vs
SUPPLY VOLTAGE
1M
10M
1.4
100
Quiescent Current – mA
Per Amplifier
80
PSRR – dB
Voltage Gain – dB
OPEN-LOOP GAIN/PHASE
vs
FREQUENCY
60
40
20
1.2
1
0.8
0.6
0.4
0
1
10
100
Frequency – Hz
3
3.5
4
4.5
Supply Voltage – V
Figure 3.
Figure 4.
1k
10k
100k
1M
10M
1.5
Submit Documentation Feedback
2
2.5
5
5.5
6
5
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
At TCASE = 25°C, RL = 10 kΩ, and connected to VS/2, VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
VOUT = –10 dBv
G = 10, RL = 2 kΩ
VS = 1.8 V
THD+N – %
0.1
1
G = 10, RL = 2 kΩ
VS = 5 V
(VS = 5 V, VOUT = 1 Vrms)
0.1
THD+N – %
1
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
G = 10, RL = 10 kΩ
VS = 1.8 V, 5 V
0.01
0.001
G = 1,
RL = 10 kΩ
G = 1,
RL = 2 kΩ VS = 1.8 V, 5 V
VS = 5 V
G = 1, RL = 2 kΩ
VS = 1.8 V
0.0001
10
100
1k
10k
G = 10, RL = 2 kΩ
0.01
G = 10, RL = 10 kΩ
0.001
G = 1, RL = 2 kΩ
0.0001
10
100k
100
Frequency – Hz
10k
Figure 6.
INPUT VOLTAGE NOISE SPECTRAL DENSITY
vs
FREQUENCY
SHORT-CIRCUIT CURRENT
vs
SUPPLY VOLTAGE
100k
120
Short-Circuit Current – mA
Input Voltage Noise – nV/√Hz
1k
Frequency – Hz
Figure 5.
1000
100
100
+ISC
80
60
40
–ISC
20
0
10
10
100
1k
Frequency – Hz
10k
100k
1.5
Figure 7.
6
G = 1, RL = 10 kΩ
2
2.5
3
3.5
4
4.5
Supply Voltage – V
Figure 8.
Submit Documentation Feedback
5
5.5
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
At TCASE = 25°C, RL = 10 kΩ, and connected to VS/2, VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
OUTPUT VOLTAGE SWING
vs
OUTPUT CURRENT
4
VS = 2.5 V
VS = 1.65 V
Output Voltage – V
2
1
VS = 0.9 V
0
-1
-2
VS = 1.65 V
VS = 2.5 V
-3
0
10
20
TA = –40°C
TA = 25°C
TA = 125°C
30 40 50 60 70
Output Current – mA
80
Input Bias Current – pA
3
INPUT BIAS CURRENT
vs
INPUT COMMON-MODE VOLTAGE
0
-2
VCM = 5.1 V
-4
-6
-8
VCM = –0.1 V
-10
-0.5
90 100
0.5
1.5
2.5
3.5
4.5
Common-Mode Voltage – V
Figure 9.
Figure 10.
INPUT OFFSET CURRENT
vs
TEMPERATURE
INPUT BIAS CURRENT
vs
TEMPERATURE
10k
5.5
10k
Input Bias Current – pA
Input Offset Current – pA
2
1k
100
10
1
1k
100
10
1
-50
-25
0
25
50
75
Temperature – °C
100
125
-50
Figure 11.
-25
0
25
50
75
Temperature – °C
100
125
Figure 12.
Submit Documentation Feedback
7
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
At TCASE = 25°C, RL = 10 kΩ, and connected to VS/2, VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
SMALL-SIGNAL OVERSHOOT
vs
LOAD CAPACITANCE
SETTLING TIME
vs
CLOSED-LOOP GAIN
100
60
Settling Time – µs
Overshoot – %
50
40
30
20
G = +1
0.01%
10
0.1%
1
10
G = +10
0.1
0
100
1k
1
Load Capacitance – pF
10
Closed-Loop Gain – V/V
Figure 13.
Figure 14.
OFFSET DRIFT DISTRIBUTION
OUTPUT ENABLE CHARACTERISTIC
(VS = 5 V, VOUT = 20 kHz Sinusoid)
VOUT
15
10
VENABLE
Percent of Amplifiers – %
20
5
0
0
1
2
3
4
5
6
7
8
9
>10
50 µs/div
Offset Voltage Drift – µV/°C
Figure 15.
8
Figure 16.
Submit Documentation Feedback
100
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
TYPICAL CHARACTERISTICS (continued)
At TCASE = 25°C, RL = 10 kΩ, and connected to VS/2, VOUT = VS/2, VCM = VS/2 (unless otherwise noted)
CHANNEL SEPARATION
vs
FREQUENCY
SMALL-SIGNAL STEP RESPONSE
(CL = 100 pF)
120
110
50 mV/div
100
90
80
70
60
50
40
10
100
1k
10k
100k
Frequency – Hz
1M
250 ns/div
10M
Figure 17.
Figure 18.
LARGE-SIGNAL STEP RESPONSE
(CL = 100 pF)
1 V/div
Channel Separation – dB
130
1 µs/div
Figure 19.
Submit Documentation Feedback
9
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION
The OPAx364 series op amps are rail-to-rail operational amplifiers with excellent CMRR, low noise, low offset,
and wide bandwidth on supply voltages as low as ±0.9 V. This family does not exhibit phase reversal and is
unity-gain stable. Specified over the industrial temperature range of –40°C to 125°C, the OPAx364 family offers
precision performance for a wide range of applications.
Rail-to-Rail Input
The OPAx364 features excellent rail-to-rail operation, with supply voltages as low as ±0.9 V. The input commonmode voltage range of the OPAx364 family extends 100 mV beyond supply rails. The unique input topology of
the OPAx364 eliminates the input offset transition region typical of most rail-to-rail complimentary stage
operational amplifiers, allowing the OPAx364 to provide superior common-mode performance over the entire
common-mode input range (see Figure 20). This feature prevents degradation of the differential linearity error
and THD when driving A/D converters. A simplified schematic of the OPAx364 is shown in Figure 21.
1.0
OPAx364
0.5
0
VOS – mV
-0.5
-1.0
-1.5
-2.0
Competitors
-2.5
-3.0
-3.5
-0.2 0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Common-Mode Voltage – VCM
Figure 20. OPAx364 Linear Offset Over Entire Common-Mode Range
10
Submit Documentation Feedback
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
VS
Regulated
Charge Pump
VOUT = VCC +1.8 V
VCC + 1.8 V
IBIAS
Patent-Pending
Very Low-Ripple
Topology
IBIAS
VOUT
IBIAS
VIN–
VIN+
IBIAS
Figure 21. Simplified Schematic
Operating Voltage
The OPAx364 series of operational amplifier parameters are fully specified from 1.8 V to 5.5 V. Single 0.1-µF
bypass capacitors should be placed across supply pins and as close to the part as possible. Supply voltages
higher than 5.5 V (absolute maximum) may cause permanent damage to the amplifier. Many specifications apply
from –40°C to 125°C. Parameters that vary significantly with operating voltages or temperature are shown in the
Typical Characteristics.
Submit Documentation Feedback
11
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
Capacitive Load
The OPAx364 series operational amplifiers can drive a wide range of capacitive loads. However, all operational
amplifiers under certain conditions may become unstable. Operational amplifier configuration, gain, and load
value are just a few of the factors to consider when determining stability. An operational amplifier in unity-gain
configuration is the most susceptible to the effects of capacitive load. The capacitive load reacts with the output
resistance of the operational amplifier to create a pole in the small-signal response, which degrades the phase
margin.
In unity gain, the OPAx364 series operational amplifiers perform well with a pure capacitive load up to
approximately 1000 pF. The equivalent series resistance (ESR) of the loading capacitor may be sufficient to
allow the OPAx364 to directly drive large capacitive loads (>1 µF). Increasing gain enhances the amplifier’s
ability to drive more capacitance as shown in Figure 13.
One method of improving capacitive load drive in the unity gain configuration is to insert a 10-Ω to 20-Ω resistor
in series with the output, as shown in Figure 22. This significantly reduces ringing with large capacitive loads.
However, if there is a resistive load in parallel with the capacitive load, it creates a voltage divider introducing a
dc error at the output and slightly reduces output swing. This error may be insignificant. For instance, with
RL = 10 kΩ and RS = 20 Ω, there is only about a 0.2% error at the output.
V+
RS
VOUT
OPAx364
10 W to
20 W
VIN
RL
CL
Figure 22. Improving Capacitive Load Drive
Input and ESD Protection
All OPAx364 pins are static protected with internal ESD protection diodes tied to the supplies. These diodes
provide overdrive protection if the current is externally limited to 10 mA, as stated in the absolute maximum
ratings and shown in Figure 23.
V+
IOVERLOAD
10 mA max
–
OPAx364
VIN
VOUT
+
5 kW
Figure 23. Input Current Protection
Achieving Output Swing to the Operational Amplifier's Negative Rail
Some applications require an accurate output voltage swing from 0 V to a positive full-scale voltage. A good
single-supply operational amplifier may be able to swing within a few mV of single supply ground, but as the
output is driven toward 0 V, the output stage of the amplifier prevents the output from reaching the negative
supply rail of the amplifier.
The output of the OPAx364 can be made to swing to ground, or slightly below, on a single-supply power source.
To do so requires use of another resistor and an additional, more-negative power supply than the operational
amplifier's negative supply. A pulldown resistor may be connected between the output and the additional
negative supply to pull the output down below the value that the output would otherwise achieve as shown in
Figure 24.
12
Submit Documentation Feedback
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
V+ = 5 V
VOUT
OPAx364
VIN
500 µA
Negative
Supply
Grounded
RP = 10 kΩ
–V = –5 V
(Additional Negative Supply)
Figure 24. Swing to Ground
This technique does not work with all operational amplifiers. The output stage of the OPAx364 allows the output
voltage to be pulled below that of most operational amplifiers, if approximately 500 µA is maintained through the
output stage. To calculate the appropriate value load resistor and negative supply, RL = –V/500 µA. The
OPAx364 has been characterized to perform well under the described conditions, maintaining excellent
accuracy down to 0 V and as low as –10 mV. Limiting and nonlinearity occurs below –10 mV, with linearity
returning as the output is again driven above –10 mV.
Buffered Reference Voltage
Many single-supply applications require a mid-supply reference voltage. The OPAx364 offer excellent capacitive
load drive capability and can be configured to provide a 0.9-V reference voltage (see Figure 25). For appropriate
loading considerations, see the Capacitive Load section.
V+
V+
R1
10 kΩ
0.9 V
OPAx364
CL = 1 µF
R2
10 kΩ
Figure 25. OPAx364 Provides a Stable Reference Voltage
Submit Documentation Feedback
13
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
Directly Driving the ADS8324 and the MSP430
The OPAx364 series operational amplifiers are optimized for driving medium speed (up to 100 kHz) sampling
A/D converters. However, they also offer excellent performance for higher-speed converters. The no crossover
input stage of the OPAx364 directly drives A/D converters without degradation of differential linearity and THD.
They provide an effective means of buffering the A/D converters input capacitance and resulting charge
injection, while providing signal gain. Figure 26 and Figure 27 show the OPAx364 configured to drive the
ADS8324 and the 12-bit A/D converter on the MSP430.
V+ = 1.8 V
V+ = 1.8 V
100 W
–
ADS8324
OPAx364
VIN
1 nF
+
Figure 26. OPAx364 Directly Drives the ADS8324
V+
V+
100 Ω
–
OPAx364
MSP430
+
VIN
1 nF
Figure 27. Driving the 12-Bit A/D Converter on the MSP430
Audio Applications
The OPAx364 family has linear offset voltage over the entire input common-mode range. Combined with
low-noise, this feature makes the OPAx364 suitable for audio applications. Single-supply 1.8-V operation allows
the OPA2364 to be an optimal candidate for dual stereo-headphone drivers and microphone preamplifiers in
portable stereo equipment (see Figure 28).
49 kΩ
Clean 3.3-V Supply
3.3 V
4 kΩ
OPA2364
+
Electret
Microphone
6 kΩ
5 kΩ
1 µF
Figure 28. Microphone Preamplifier
14
Submit Documentation Feedback
VOUT
OPA2364-Q1, OPA4364-Q1
www.ti.com
SGLS363A – JUNE 2006 – REVISED OCTOBER 2006
APPLICATION INFORMATION (continued)
Active Filtering
Low harmonic distortion and noise specifications plus high gain and slew rate make the OPAx364 optimal
candidates for active filtering. Figure 29 shows the implementation of a Sallen-Key, 3-pole, low-pass Bessel
filter.
220 pF
1.8 kΩ
19.5 kΩ
VIN = 1 Vrms
3.3 nF
150 kΩ
+
47 pF OPAx364
–
VOUT
Figure 29. OPAx364 Configured as 3-Pole, 20-kHz, Sallen-Key Filter
Submit Documentation Feedback
15
PACKAGE OPTION ADDENDUM
www.ti.com
27-May-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
OPA4364AQDRQ1
ACTIVE
SOIC
D
Pins Package Eco Plan (2)
Qty
14
2500 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF OPA4364-Q1 :
• Catalog: OPA4364
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
OPA4364AQDRQ1
Package Package Pins
Type Drawing
SOIC
D
14
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
6.5
B0
(mm)
K0
(mm)
P1
(mm)
9.0
2.1
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA4364AQDRQ1
SOIC
D
14
2500
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated