STP5NK80Z STP5NK80ZFP N-channel 800V - 1.9Ω - 4.3A - TO-220/TO-220FP Zener-protected SuperMESH™ Power MOSFET General features Type VDSS (@Tjmax) STP5NK80Z STP5NK80ZFP RDS(on) ID 800 V < 2.4 Ω 4.3 A 800 V < 2.4 Ω 4.3 A 3 ■ 100% avalanche tested ■ Gate charge minimized ■ Very low intrinsic capacitances ■ Very good manufacturing repeatibility 1 TO-220 2 TO-220FP Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage MOSFETs including revolutionary MDmesh™ products. Internal schematic diagram Applications ■ Switching application Order codes Part number Marking Package Packaging STP5NK80Z P5NK80Z TO-220 Tube STP5NK80ZFP P5NK80ZFP TO-220FP Tube August 2006 Rev 4 1/15 www.st.com 15 Contents STP5NK80Z - STP5NK80ZFP Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................ 7 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2/15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 STP5NK80Z - STP5NK80ZFP 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Symbol Parameter Value TO-220 Unit TO-220FP VDS Drain-source voltage (VGS = 0) 800 V VGS Gate-source voltage ± 30 V ID Drain current (continuous) at TC = 25°C 4.3 4.3 (1) A ID Drain current (continuous) at TC=100°C 2.7 2.7 (1) A IDM(2) Drain current (pulsed) 17.2 17.2 (1) A PTOT Total dissipation at TC = 25°C 110 30 W Derating factor 0.88 0.24 W/°C VESD(G-S) dv/dt (3) VISO TJ Tstg Gate source ESD (HBM-C=100pF, R=1.5ΚΩ) Peak diode recovery voltage slope Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s; Tc= 25°C) 3500 V 4.5 V/ns - Operating junction temperature Storage temperature 2500 V -55 to 150 °C Value Unit 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤4.3A, di/dt ≤200A/µs, VDD ≤V(BR)DSS, Tj ≤TJMAX. Table 2. Symbol Rthj-case Thermal data Parameter Thermal resistance junction-case max TO-220 TO-220FP 1.14 4.2 °C/W Rthj-a Thermal resistance junction-ambient max 62.5 °C/W Tl Maximum lead temperature for soldering purpose 300 °C 3/15 Electrical ratings Table 3. STP5NK80Z - STP5NK80ZFP Avalanche characteristics Symbol Value Unit IAR Avalanche current, repetitive or not-repetitive (pulse width limited by Tj Max) 4.3 A EAS Single pulse avalanche energy (starting Tj=25°C, Id=Iar, Vdd=50V) 190 mJ Table 4. Symbol BVGSO 1.1 Parameter Gate-source zener diode Parameter Test conditions Gate-source breakdown voltage Igs=± 1mA (Open Drain) Min. Typ. 30 Max. Unit V Protection features of gate-to-source zener diodes The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 4/15 STP5NK80Z - STP5NK80ZFP 2 Electrical characteristics Electrical characteristics (TCASE=25°C unless otherwise specified) Table 5. Symbol On/off states Parameter Test conditions Drain-source breakdown voltage ID = 1mA, VGS= 0 IDSS Zero gate voltage drain current (VGS = 0) VDS = Max rating, VDS = Max rating, Tc = 125°C IGSS Gate body leakage current VGS = ± 20V (VGS = 0) V(BR)DSS VGS(th) Gate threshold voltage VDS = VGS, ID = 100µA RDS(on) Static drain-source on resistance VGS = 10V, ID = 2.15 A Table 6. Symbol Min. Typ. Max. Unit 800 3 V 1 50 µA µA ±10 µA 3.75 4.5 V 1.9 2.4 Ω Typ. Max. Unit Dynamic Parameter Test conditions Min. gfs (1) Forward transconductance VDS =15V, ID = 2.15A 4.25 S Ciss Coss Crss Input capacitance Output capacitance Reverse transfer capacitance VDS =25V, f=1 MHz, VGS=0 910 98 20 pF pF pF Cosseq(2). Equivalent output capacitance VGS=0, VDS =0V to 400V 40 pF td(on) tr td(off) tr Turn-on delay time Rise time Turn-on delay time fall time VDD=400 V, ID= 2 A, RG=4.7Ω, VGS=10V (see Figure 18) 18 25 45 30 ns ns ns ns Qg Qgs Qgd Total gate charge Gate-source charge Gate-drain charge VDD=640V, ID = 4.3A VGS =10V 32.4 5 18.5 td(Voff) tr Off-voltage rise time Fall time Cross-over time VDD=640 V, ID= 4.3 A, RG=4.7Ω, VGS=10V (see Figure 20) 22 10 32 45.5 nC nC nC ns ns ns 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS 5/15 Electrical characteristics Table 7. Symbol ISD Source drain diode Parameter Min Typ. Max Unit Source-drain current 4.3 A Source-drain current (pulsed) 17.2 A (2) Forward on voltage ISD= 4.3 A, VGS=0 1.6 V Reverse recovery time Reverse recovery charge Reverse recovery current ISD= 4.3 A, di/dt = 100A/µs, VDD=40 V, Tj = 150°C (see Figure 20) trr Qrr IRRM 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration=300µs, duty cycle 1.5% 6/15 Test conditions (1) ISDM VSD STP5NK80Z - STP5NK80ZFP 500 3 12 ns µC A STP5NK80Z - STP5NK80ZFP Electrical characteristics 2.1 Electrical characteristics (curves) Figure 1. Safe operating area for TO-220 Figure 2. Thermal impedance for TO-220 Figure 3. Safe operating area for TO-220FP (HV11720) Figure 4. Thermal impedance for TO-220FP Figure 5. Output characterisics Figure 6. Transfer characteristics 7/15 Electrical characteristics STP5NK80Z - STP5NK80ZFP Figure 7. Transconductance Figure 9. Gate charge vs gate-source voltage Figure 10. Capacitance variations Figure 11. Normalized gate threshold voltage vs temperature 8/15 Figure 8. Static drain-source on resistance Figure 12. Normalized on resistance vs temperature STP5NK80Z - STP5NK80ZFP Figure 13. Source-drain diode forward characteristics Electrical characteristics Figure 14. Normalized BVdss vs temperature Figure 15. Avalanche energy vs temperature 9/15 Test circuit 3 STP5NK80Z - STP5NK80ZFP Test circuit Figure 16. Unclamped Inductive load test circuit Figure 17. Unclamped Inductive waveform Figure 18. Switching times test circuit for resistive load Figure 19. Gate charge test circuit Figure 20. Test circuit for inductive load switching and diode recovery times 10/15 STP5NK80Z - STP5NK80ZFP 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/15 Package mechanical data STP5NK80Z - STP5NK80ZFP TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 12/15 L5 1 2 3 L4 STP5NK80Z - STP5NK80ZFP Package mechanical data TO-220 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.137 L20 16.40 L30 0.154 0.645 28.90 1.137 øP 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 13/15 Revision history 5 STP5NK80Z - STP5NK80ZFP Revision history Table 8. 14/15 Revision history Date Revision Changes 09-Sep-2004 2 Preliminary version 06-Sep-2005 3 Final version 16-Aug-2006 4 New template, no content change STP5NK80Z - STP5NK80ZFP Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15