SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 D D D D D D D D D D D Member of the Texas Instruments Widebus Family Load Clock and Unload Clock Can Be Asynchronous or Coincident 512 Words by 18 Bits Low-Power Advanced CMOS Technology Full, Empty, and Half-Full Flags Programmable Almost-Full/Almost-Empty Flag Fast Access Times of 15 ns With a 50-pF Load and All Data Outputs Switching Simultaneously Data Rates up to 50 MHz 3-State Outputs Pin-to-Pin Compatible With SN74ACT7806 and SN74ACT7814 Packaged in Shrink Small-Outline 300-mil Package Using 25-mil Center-to-Center Spacing description A FIFO memory is a storage device that allows data to be written into and read from its array at independent data rates. The SN74ACT7804 is a 512-word by 18-bit FIFO for high speed and fast access times. It processes data at rates up to 50 MHz and access times of 15 ns in a bit-parallel format. Data is written into memory on a low-to-high transition at the load-clock (LDCK) input and is read out on a low-to-high transition at the unload-clock (UNCK) input. The memory is full when the number of words clocked in exceeds the number of words clocked out by 512. When the memory is full, LDCK signals have no effect on the data residing in memory. When the memory is empty, UNCK signals have no effect. DL PACKAGE (TOP VIEW) RESET D17 D16 D15 D14 D13 D12 D11 D10 VCC D9 D8 GND D7 D6 D5 D4 D3 D2 D1 D0 HF PEN AF/AE LDCK NC NC FULL 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 OE Q17 Q16 Q15 GND Q14 VCC Q13 Q12 Q11 Q10 Q9 GND Q8 Q7 Q6 Q5 VCC Q4 Q3 Q2 GND Q1 Q0 UNCK NC NC EMPTY NC – No internal connection Status of the FIFO memory is monitored by the full (FULL), empty (EMPTY), half-full (HF), and almost-full/almost-empty (AF/AE) flags. The FULL output is low when the memory is full and high when the memory is not full. The EMPTY output is low when the memory is empty and high when it is not empty. The HF output is high when the FIFO contains 256 or more words. The AF/AE status flag is a programmable flag. The first one or two low-to-high transitions of LDCK after reset are used to program the almost-empty offset value (X) and the almost-full offset value (Y) if program enable (PEN) is low. The AF/AE flag is high when the FIFO contains X or fewer words or (512 – Y) or more words. The AF/AE flag is low when the FIFO contains between (X + 1) and (511 – Y) words. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments Incorporated. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 description (continued) A low level on the reset (RESET) input resets the internal stack pointers and sets FULL high, AF/AE high, HF low, and EMPTY low. The Q outputs are not reset to any specific logic level. The FIFO must be reset upon power up. The first word loaded into empty memory causes EMPTY to go high and the data to appear on the Q outputs. It is important to note that the first word does not have to be unloaded. The data outputs are noninverting with respect to the data inputs and are in the high-impedance state when the output-enable (OE) input is high. The SN74ACT7804 is characterized for operation from 0°C to 70°C. logic symbol† RESET LDCK UNCK 1 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 23 21 FULL LDCK 32 56 D0 RESET 25 OE PEN Φ FIFO 512 × 18 SN74ACT7804 HALF-FULL UNCK ALMOST FULL/EMPTY EN1 EMPTY 22 24 FULL HF AF/AE 29 EMPTY PROGRAM ENABLE 0 0 33 20 34 19 36 18 37 17 38 16 40 15 41 14 42 12 43 11 Data Data 45 1 9 46 8 47 7 48 6 49 5 51 4 53 3 54 2 55 17 17 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 Q17 SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 functional block diagram OE D0–D17 Location 1 Location 2 Read Pointer UNCK 512 × 18 SRAM Write Pointer LDCK Location 511 Location 512 Q0–Q17 EMPTY Reset Logic RESET StatusFlag Logic PEN FULL HF AF/AE Terminal Functions TERMINAL I/O DESCRIPTION 24 O Almost-full/almost-empty flag. Depth-offset values can be programmed for AF/AE, or the default value of 64 can be used for both the almost-empty offset (X) and the almost-full offset (Y). AF/AE is high when memory contains X or fewer words or (512 – Y) or more words. AF/AE is high after reset. D0–D17 2–9, 11–12, 14–21 I 18-bit data input port EMPTY 29 O Empty flag. EMPTY is low when the FIFO is empty. A FIFO reset also causes EMPTY to go low. FULL 28 O Full flag. FULL is low when the FIFO is full. A FIFO reset causes FULL to go high. HF 22 O Half-full flag. HF is high when the FIFO memory contains 256 or more words. HF is low after reset. LDCK 25 I Load clock. Data is written to the FIFO on the rising edge of LDCK when FULL is high. OE 56 I Output enable. When OE is high, the data outputs are in the high-impedance state. PEN 23 I Program enable. After reset and before the first word is written to the FIFO, the binary value on D0–D7 is latched as an AF/AE offset value when PEN is low and LDCK is high. 33–34, 36–38, 40–43, 45–49, 51, 53–55 O 18-bit data output port RESET 1 I Reset. A low level on RESET resets the FIFO and drives AF/AE and FULL high and HF and EMPTY low. UNCK 32 I Unload clock. Data is read from the FIFO on the rising edge of UNCK when EMPTY is high. NAME NO. AF/AE Q0–Q17 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 offset values for AF/AE The AF/AE flag has two programmable limits: the almost-empty offset value (X) and the almost-full offset value (Y). They can be programmed after the FIFO is reset and before the first word is written to memory. The AF/AE flag is high when the FIFO contains X or fewer words or (512 – Y) or more words. To program the offset values, PEN can be brought low after reset only when LDCK is low. On the following low-to-high transition of LDCK, the binary value on D0–D7 is stored as the almost-empty offset value (X) and the almost-full offset value (Y). Holding PEN low for another low-to-high transition of LDCK reprograms Y to the binary value on D0–D7 at the time of the second LDCK low-to-high transition. Writes to the FIFO memory are disabled while the offsets are programmed. A maximum value of 255 can be programmed for either X or Y (see Figure 1). To use the default values of X = Y = 64, PEN must be held high. RESET LDCK ÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎ Don’t Care PEN ÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏ ÌÌÌÌÌ ÌÌÌÌÌ D0–D7 Don’t Care X and Y Y EMPTY Figure 1. Programming X and Y Separately 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 RESET 1 0 PEN ÏÏ ÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏ ÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ ÏÏ LDCK D0–D17 W1 W2 W (X+1) W256 W (512–Y) Don’t Care W512 1 0 W1 W2 W (Y+1) W (Y+2) W257 W258 W (512–X) ÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏ • DALLAS, TEXAS 75265 Q0–Q17 W (513–X) ÏÏ ÏÏ ÏÏ ÏÏ OE W511 W512 EMPTY AF/AE HF Define the AF/AE Flag Using the Default Value of X and Y Figure 2. Write, Read, and Flag Timing Reference 5 SCAS204C – APRIL 1992 – REVISED APRIL 1998 FULL SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY POST OFFICE BOX 655303 UNCK SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Package thermal impedance, θJA (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions ’ACT7804-20 VCC VIH Supply voltage VIL IOH Low-level input voltage High-level input voltage Low level output current Low-level TA Operating free-air temperature ’ACT7804-40 MAX MIN MAX MIN MAX 4.5 5.5 4.5 5.5 4.5 5.5 2 High-level output current IOL ’ACT7804-25 MIN 2 2 UNIT V V 0.8 0.8 0.8 V Q outputs, flags –8 –8 –8 mA Q outputs 16 16 16 8 8 8 Flags 0 70 0 70 0 70 mA °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL II IOZ ICC ∆ICC§ Ci Flags Q outputs TEST CONDITIONS TYP‡ MAX 2.4 UNIT VCC = 4.5 V, VCC = 4.5 V, IOH = –8 mA IOL = 8 mA VCC = 4.5 V, VCC = 5.5 V, IOL = 16 mA VI = VCC or 0 0.5 ±5 µA VCC = 5.5 V, VCC = 5.5 V, VO = VCC or 0 VI = VCC – 0.2 V or 0 ±5 µA VCC = 5.5 V, VI = 0, One input at 3.4 V, Other inputs at VCC or GND f = 1 MHz VO = 0, f = 1 MHz ‡ All typical values are at VCC = 5 V, TA = 25°C. § This is the supply current for each input that is at one of the specified TTL voltage levels rather 0 V or VCC. POST OFFICE BOX 655303 V 0.5 Co 6 MIN • DALLAS, TEXAS 75265 V 400 µA 1 mA 4 pF 8 pF SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 timing requirements over recommended operating conditions (see Figures 1 through 3) ’ACT7804-20 MIN fclock tw Clock frequency MIN Setup time Hold time MAX ’ACT7804-40 MIN 40 MAX 25 LDCK high or low 7 8 12 UNCK high or low 7 8 12 PEN low 7 8 12 10 10 12 RESET low th ’ACT7804-25 50 Pulse duration tsu MAX D0–D17 before LDCK↑ 5 5 5 PEN before LDCK↑ 5 5 5 LDCK inactive before RESET high 5 6 6 D0–D17 after LDCK↑ 0 0 0 LDCK inactive after RESET high 5 6 6 PEN low after LDCK↑ 3 3 3 PEN high after LDCK↓ 0 0 0 UNIT MHz ns ns ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 3) PARAMETER FROM (INPUT) fmax LDCK or UNCK tpd d tpd‡ tPLH TO (OUTPUT) LDCK↑ Any Q UNCK↑ UNCK↑ Any Q LDCK↑ EMPTY UNCK↑ tPHL EMPTY RESET low LDCK↑ tPLH tpd d tPLH tPHL FULL UNCK↑ FULL RESET low LDCK↑ AF/AE UNCK↑ ’ACT7804-20 TYP† MAX ’ACT7804-25 MIN MIN 50 40 9 6 11.5 MAX ’ACT7804-40 MIN MAX 25 MHz 20 9 22 9 24 15 6 18 6 20 10.5 6 15 6 17 6 19 6 15 6 17 6 19 4 16 4 18 4 20 6 15 6 17 6 19 6 15 6 17 6 19 4 18 4 20 4 22 7 18 7 20 7 22 7 18 7 20 7 22 AF/AE 2 10 2 12 2 14 LDCK↑ HF 5 18 5 20 5 22 7 18 7 20 7 22 3 12 3 14 3 16 UNCK↑ HF ns ns RESET low RESET low UNIT ns ns ns ns ns ns ten OE Any Q 2 9 2 10 2 11 ns tdis OE Any Q 2 10 2 11 2 12 ns † All typical values are at VCC = 5 V, TA = 25°C. ‡ This parameter is measured at CL = 30 pF (see Figure 4). operating characteristics, VCC = 5 V, TA = 25°CFigure 2 PARAMETER Cpd Power dissipation capacitance per FIFO channel POST OFFICE BOX 655303 TEST CONDITIONS Outputs enabled • DALLAS, TEXAS 75265 CL = 50 pF, f = 5 MHz TYP 53 UNIT pF 7 SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 PARAMETER MEASUREMENT INFORMATION 7V PARAMETER S1 ten 500 Ω From Output Under Test Test Point CL = 50 pF (see Note A) tdis 500 Ω tpd S1 tPZH tPZL tPHZ tPLZ tPLH tPHL Open Closed Open Closed Open Open tw LOAD CIRCUIT 3V Input 0V 1.5 V VOLTAGE WAVEFORMS PULSE DURATION 0V tsu th 3V Data Input 1.5 V 1.5 V 0V 3V Output Control VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 1.5 V 1.5 V 0V tPLH 1.5 V 1.5 V tPZH 1.5 V VOL Output Waveform 2 S1 at Open VOL + 0.3 V 1.5 V VOH VOH – 0.3 V ≈0V NOTE A: CL includes probe and jig capacitance. Figure 3. Load Circuit and Voltage Waveforms • DALLAS, TEXAS 75265 VOL tPHZ VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES POST OFFICE BOX 655303 tPLZ ≈ 3.5 V Output Waveform 1 S1 at 7 V tPHL VOH 8 1.5 V 0V tPZL 3V Output 1.5 V 3V Timing Input Input 1.5 V SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 TYPICAL CHARACTERISTICS PROPAGATION DELAY TIME vs LOAD CAPACITANCE SUPPLY CURRENT vs CLOCK FREQUENCY 200 VCC = 5 V TA = 25°C RL = 500 Ω TA = 75°C CL = 0 pF 180 typ + 6 VCC = 5.5 V 160 I CC(f) – Supply Current – mA t pd – Propagation Delay Time – ns typ + 8 typ + 4 typ + 2 typ VCC = 5 V 140 120 100 VCC = 4.5 V 80 60 40 20 0 typ – 2 0 50 100 150 200 250 300 0 10 20 30 40 50 60 70 fclock – Clock Frequency – MHz CL – Load Capacitance – pF Figure 4 Figure 5 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 SN74ACT7804 512 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY SCAS204C – APRIL 1992 – REVISED APRIL 1998 APPLICATION INFORMATION LDCK SN74ACT7804 UNCK LDCK EMPTY FULL FULL OE D18–D35 D0–D17 Q0–Q17 UNCK EMPTY OE Q18–Q35 SN74ACT7804 LDCK FULL UNCK EMPTY OE D0–D17 D0–D17 Q0–Q17 Figure 6. Word-Width Expansion: 512 × 36 Bits 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Q0–Q17 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 1M7804-20DLG4 ACTIVE SSOP DL 56 1M7804-20DLRG4 ACTIVE SSOP DL 56 SN74ACT7804-20DL ACTIVE SSOP DL 56 SN74ACT7804-20DLR ACTIVE SSOP DL 56 SN74ACT7804-25DL ACTIVE SSOP DL 56 SN74ACT7804-25DLR ACTIVE SSOP DL 56 SN74ACT7804-40DL ACTIVE SSOP DL 56 SN74ACT7804-40DLR ACTIVE SSOP DL 56 20 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 20 20 20 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0°–ā8° 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated