TVS Diode Arrays (SPA™ Family of Products) General Purpose ESD Protection - SP1011 Series SP1011 Series 7pF 15kV Unidirectional TVS Array RoHS Pb GREEN Zener diodes fabricated in a proprietary silicon avalanche technology protect each I/O pin to provide a high level of protection for electronic equipment that may experience destructive electrostatic discharges (ESD). These robust diodes can safely absorb repetitive ESD strikes above the maximum level specified in the IEC 61000-4-2 international standard (Level 4, ±8kV contact discharge) without performance degradation. Their very low loading capacitance also makes them ideal for protection highspeed signal pins. Pinout Features t&4%*&$ ±15kV contact, ±30kV air I/O (1) I/O (4) GND GND t-JHIUOJOH*&$ 2A (tp=8/20μs) I/O (3) t-PXDBQBDJUBODFPGQ' (TYP) per I/O @ 2.5V I/O (2) uDFN-6 (1.25x1.0x0.5mm) 5 t&'5QSPUFDUJPO IEC61000-4-4, 40A (5/50ns) t-PXMFBLBHFDVSSFOUPG 1μA (MAX) at 5V Functional Block Diagram 6 t5JOZV%'/QBDLBHF (1.25mm x 1.0mm x 0.5mm) Applications 4 t-$%1%157 t.PCJMF1IPOF t%7%1MBZFS t/PUFCPPL t%FTLUPQ t.11.1 t4FU5PQ#PY t%JHJUBMDBNFSB Application Example 1 2 3 Keyboard Controller Input Outside World D1 D2 D3 D4 SP1011-04UTG Shield Ground Signal Ground Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. ©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 51 Revision: April 14, 2011 SP1011 Series SP1011 Description TVS Diode Arrays (SPA™ Family of Products) General Purpose ESD Protection - SP1011 Series Absolute Maximum Ratings Symbol Parameter Value Units 2 A Operating Temperature -40 to 85 °C Storage Temperature -60 to 150 °C IPP Peak Pulse Current (tp=8/20μs) TOP TSTOR CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Thermal Information Parameter Rating Units -65 to 150 °C Maximum Junction Temperature 150 °C Maximum Lead Temperature (Soldering 10s) 260 °C Storage Temperature Range Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min Typ Max Units VR IR = 1mA 7.0 7.8 8.5 V Reverse Standoff Voltage VRWM IR≤1μA 6 V Reverse Leakage Current ILEAK VR = 5V 1 μA Reverse Voltage Drop Clamp Voltage1 VC Dynamic Resistance RDYN ESD Withstand Voltage1 VESD Diode Capacitance1 0.1 IPP=1A, tp=8/20μs, Fwd 8.7 V IPP=2A, tp=8/20μs, Fwd 10.2 V (VC2 - VC1) / (IPP2 - IPP1) 1.5 Ω IEC61000-4-2 (Contact Discharge) ±15 kV IEC61000-4-2 (Air Discharge) ±30 kV CD Reverse Bias = 0V 12 Reverse Bias = 2.5V 7 15 pF pF Note: 1. Parameter is guaranteed by design and/or device characterization. Insertion Loss (S21) I/O to GND 14.0 5 12.0 0 10.0 -5 Attenuation (dB) Capacitance (pF) Capacitance vs. Reverse Bias 8.0 6.0 4.0 2.0 -10 -15 -20 -25 0.0 -30 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 10 SP1011 Series 100 1000 10000 Frequency (MHz) DC Bias (V) 52 Revision: April 14, 2011 ©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. TVS Diode Arrays (SPA™ Family of Products) General Purpose ESD Protection - SP1011 Series Soldering Parameters 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (TL) (Liquidus) Reflow - Temperature (tL) tP TP Critical Zone TL to TP Ramp-up TL TS(max) tL SP1011 Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) Temperature Reflow Condition Ramp-do Ramp-down Preheat TS(min) tS 217°C 60 – 150 seconds 25 Peak Temperature (TP) 250+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C time to peak temperature Time Package Dimensions — uDFN-6 (1.25x1.0x0.5mm) uDFN-6 (1.25x1.0x0.5mm) Bottom View Top View ℮ D Symbol A 0.05 C 4 6 5 4 5 6 L E 3 1 2 3 A 0.45 0.55 0.018 0.022 0.00 0.05 0.000 0.002 A3 A3 A Seating plane 0.127 REF 0.005 REF b 0.15 0.25 0.006 0.010 D 1.20 1.30 0.047 0.051 D2 - - - - E 0.95 1.05 0.037 0.041 E2 - - - - 0.35 0.010 e b Max A1 2 1 A1 Min 0.05 C Side View 0.05 C Inches Max Pin 1 chamfer 0.10 x 45’ B Pin 1 Index Area Millimeters Min 0.4 REF 0.016 REF C L 0.25 0.014 0.10 M C A B 0.05 M C ©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 53 Revision: April 14, 2011 SP1011 Series TVS Diode Arrays (SPA™ Family of Products) General Purpose ESD Protection - SP1011 Series Part Numbering System Product Characteristics SP 1011 – 04 U T G Silicon Protection Array (SPATM) Family of TVS Diode Arrays G= Green T= Tape & Reel Package U: uDFN-6 Series Number of Channels Lead Plating Pre-Plated Frame Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Subsitute Material Silicon Body Material Molded Epoxy Flammability UL94-V-0 Notes : Part Marking System 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. O4 4. All specifications comply to JEDEC SPEC MO-223 Issue A Product Series O = SP1011 O4 5. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. Number of Channels 6. Package surface matte finish VDI 11-13. Ordering Information Part Number Package Marking Min. Order Qty. SP1011-04UTG uDFN-6 (1.25x1.0x0.5mm) O4 3000 Embossed Carrier Tape & Reel Specification — uDFN-6 (1.25x1.0x0.5mm) Symbol D Min Max 1.85 0.06 0.07 F 3.45 3.55 0.14 0.14 D1 0.50 0.65 0.02 0.03 W B0 10P0 A0 54 Revision: April 14, 2011 1.50 MIN 3.90 4.10 40.0 +/- 0.20 0.06 MIN 0.15 0.16 1.57 +/- 0.01 W 7.90 8.30 0.31 0.33 P2 1.95 2.05 0.08 0.08 A0 1.09 1.19 0.04 0.05 B0 1.42 1.52 0.06 0.06 K0 0.71 0.81 0.03 0.03 t K0 SP1011 Series Max 1.65 D P0 Inches Min P0 F D1 Millimeters E t E P2 0.25 TYP 0.01 TYP ©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: SP1011-04UTG