ST1280C..K Series Vishay High Power Products Phase Control Thyristors (Hockey PUK Version), 2310 A FEATURES • Center amplifying gate • Metal case with ceramic insulator RoHS COMPLIANT • International standard case A-24 (K-PUK) • High profile hockey PUK A-24 (K-PUK) • Lead (Pb)-free TYPICAL APPLICATIONS PRODUCT SUMMARY • DC motor controls IT(AV) 2310 A • Controlled DC power supplies • AC controllers MAJOR RATINGS AND CHARACTERISTICS PARAMETER TEST CONDITIONS IT(AV) Ths IT(RMS) Ths VALUES UNITS 2310 A 55 °C 4150 A 25 °C 50 Hz 42 500 60 Hz 44 500 50 Hz 9027 60 Hz 8240 A ITSM I2 t VDRM/VRRM Typical tq TJ kA2s 400 to 600 V 200 µs - 40 to 125 °C ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS TYPE NUMBER ST1280C..K VOLTAGE CODE VDRM/VRRM, MAXIMUM REPETITIVE PEAK VRSM, MAXIMUM IDRM/IRRM MAXIMUM AND OFF-STATE VOLTAGE NON-REPETITIVE PEAK VOLTAGE AT TJ = TJ MAXIMUM V V mA 04 400 500 06 600 700 Document Number: 93718 Revision: 11-Aug-08 For technical questions, contact: [email protected] 100 www.vishay.com 1 ST1280C..K Series Vishay High Power Products Phase Control Thyristors (Hockey PUK Version), 2310 A ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current at heatsink temperature IT(AV) Maximum RMS on-state current IT(RMS) TEST CONDITIONS 180° conduction, half sine wave Double side (single side) cooled 25 °C heatsink temperature double side cooled t = 10 ms Maximum peak, one-cycle non-repetitive surge current ITSM t = 8.3 ms t = 10 ms t = 8.3 ms t = 10 ms Maximum I2t for fusing I2 t t = 8.3 ms t = 10 ms t = 8.3 ms Maximum I2√t for fusing I2√t No voltage reapplied UNITS A 55 (85) °C 4150 42 500 No voltage reapplied 100 % VRRM reapplied VALUES 2310 (885) 44 500 Sinusoidal half wave, initial TJ = TJ maximum 37 400 9027 8241 6383 100 % VRRM reapplied 90 270 Low level value of threshold voltage VT(TO)1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 0.83 VT(TO)2 (I > π x IT(AV)), TJ = TJ maximum 0.90 Low level value of on-state slope resistance rt1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 0.077 High level value of on-state slope resistance rt2 (I > π x IT(AV)), TJ = TJ maximum 0.068 Ipk = 8000 A, TJ = TJ maximum, tp = 10 ms sine pulse 1.44 VTM Maximum holding current IH Typical latching current IL kA2s 5828 t = 0.1 to 10 ms, no voltage reapplied High level value of threshold voltage Maximum on-state voltage A 35 700 600 TJ = 25 °C, anode supply 12 V resistive load 1000 kA2√s V mΩ V mA SWITCHING PARAMETER Maximum non-repetitive rate of rise of turned-on current SYMBOL dI/dt TEST CONDITIONS Gate drive 20 V, 20 Ω, tr ≤ 1 µs TJ = TJ maximum, anode voltage ≤ 80 % VDRM VALUES UNITS 1000 A/µs Typical delay time td Gate current 1 A, dIg/dt = 1 A/µs Vd = 0.67 % VDRM, TJ = 25 °C 1.9 Typical turn-off time tq ITM = 550 A, TJ = TJ maximum, dI/dt = 40 A/µs, VR = 50 V, dV/dt = 20 V/µs, gate 0 V 100 Ω, tp = 500 µs 200 SYMBOL TEST CONDITIONS VALUES UNITS µs BLOCKING PARAMETER Maximum critical rate of rise of off-state voltage dV/dt TJ = TJ maximum linear to 80 % rated VDRM 500 V/µs Maximum peak reverse and off-state leakage current IRRM, IDRM TJ = TJ maximum, rated VDRM/VRRM applied 100 mA www.vishay.com 2 For technical questions, contact: [email protected] Document Number: 93718 Revision: 11-Aug-08 ST1280C..K Series Phase Control Thyristors Vishay High Power Products (Hockey PUK Version), 2310 A TRIGGERING PARAMETER SYMBOL Maximum peak gate power PGM Maximum average gate power PG(AV) Maximum peak positive gate current IGM Maximum peak positive gate voltage + VGM Maximum peak negative gate voltage - VGM VALUES TEST CONDITIONS TYP. MAX. TJ = TJ maximum, tp ≤ 5 ms 16 TJ = TJ maximum, f = 50 Hz, d% = 50 3 IGT TJ = 25 °C Maximum required gate trigger/ current/voltage are the lowest value which will trigger all units 12 V anode to cathode applied TJ = - 40 °C VGT TJ = 25 °C TJ = 125 °C DC gate current not to trigger IGD DC gate voltage not to trigger VGD V 5.0 TJ = 125 °C DC gate voltage required to trigger A 20 TJ = - 40 °C DC gate current required to trigger W 3.0 TJ = TJ maximum, tp ≤ 5 ms TJ = TJ maximum Maximum gate current/voltage not to trigger is the maximum value which will not trigger any unit with rated VDRM anode to cathode applied UNITS 200 - 100 200 50 - 1.4 - 1.1 3.0 0.9 - mA V 10 mA 0.25 V VALUES UNITS THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum operating temperature range Maximum storage temperature range Maximum thermal resistance, junction to heatsink Maximum thermal resistance, case to heatsink TEST CONDITIONS TJ - 40 to 125 TStg - 40 to 150 RthJ-hs RthC-hs DC operation single side cooled 0.042 DC operation double side cooled 0.021 DC operation single side cooled 0.006 DC operation double side cooled 0.003 Mounting force, ± 10 % Approximate weight Case style See dimensions - link at the end of datasheet °C K/W 24 500 (2500) N (kg) 425 g A-24 (K-PUK) ΔRthJC CONDUCTION CONDUCTION ANGLE SINUSOIDAL CONDUCTION RECTANGULAR CONDUCTION SINGLE SIDE DOUBLE SIDE SINGLE SIDE DOUBLE SIDE 180° 0.003 0.003 0.002 0.002 120° 0.004 0.004 0.004 0.004 90° 0.005 0.005 0.005 0.005 60° 0.007 0.007 0.007 0.007 30° 0.012 0.012 0.012 0.012 TEST CONDITIONS UNITS TJ = TJ maximum K/W Note • The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC Document Number: 93718 Revision: 11-Aug-08 For technical questions, contact: [email protected] www.vishay.com 3 ST1280C..K Series Vishay High Power Products Phase Control Thyristors 130 ST1280C..K Series (Single Side Cooled) R thJ-hs (DC) = 0.042 K/W 120 110 100 90 Conduction Angle 80 70 30˚ 60 60˚ 90˚ 50 120˚ 180˚ 40 0 400 800 1200 1600 Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C) (Hockey PUK Version), 2310 A 130 ST1280C..K Series (Double Side Cooled) R thJ-hs (DC) = 0.021 K/W 120 110 100 90 80 Conduction Period 70 60 30˚ 50 40 30 90˚ 120˚ 180˚ 20 0 Average On-state current (A) 100 90 80 Conduction Period 70 60 30˚ 50 60˚ 90˚ 40 120˚ 30 180˚ DC 20 0 500 1000 1500 2000 2500 3000 DC 4000 5000 3600 3200 180˚ 120˚ 90˚ 60˚ 30˚ 2800 2400 2000 RMS Limit 1600 1200 Conduction Angle 800 ST1280C..K Series T J = 125˚C 400 0 0 500 1000 1500 2000 2500 3000 Average On-state current (A) Average On-state Current (A) Fig. 2 - Current Ratings Characteristics Fig. 5 - On-State Power Loss Characteristics 130 ST1280C..K Series (Double Side Cooled) R thJ-hs (DC) = 0.021 K/W 120 110 100 90 Conduction Angle 80 70 60 50 30˚ 60˚ 40 90˚ 120˚ 180˚ 30 0 500 1000 1500 2000 2500 3000 Average On-state Current (A) Fig. 3 - Current Ratings Characteristics www.vishay.com 4 Maximum Average On-state Power Loss (W) 110 2000 Fig. 4 - Current Ratings Characteristics Maximum Average On-state Power Loss (W) Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C) ST1280C..K Series (Single Side Cooled) R thJ-hs (DC) = 0.042 K/W 120 1000 Average On-state Current (A) Fig. 1 - Current Ratings Characteristics 130 60˚ 5000 4500 DC 180˚ 120˚ 90˚ 60˚ 30˚ 4000 3500 3000 2500 RMS Limit 2000 Conduction Period 1500 1000 ST1280C..K Series TJ = 125˚C 500 0 0 1000 2000 3000 4000 5000 Average On-state Current (A) Fig. 6 - On-State Power Loss Characteristics For technical questions, contact: [email protected] Document Number: 93718 Revision: 11-Aug-08 ST1280C..K Series 40000 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) Phase Control Thyristors Vishay High Power Products (Hockey PUK Version), 2310 A At Any Rated Load Condition And With Rated V RRMApplied Following Surge. Initial T J= 125˚C 35000 @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 30000 25000 20000 ST1280C..K Series 15000 1 10 100 45000 40000 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial T J= 125 ˚C No Voltage Reapplied Rated V RRMReapplied 35000 30000 25000 20000 ST1280C..K Series 15000 0.01 0.1 1 Number Of Equal Amplitude Half Cycle Current Pulses (N) Pulse Train Duration (s) Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Instantaneous On-state Current (A) 100000 10000 TJ = 25˚C TJ = 125˚C 1000 ST1280C..K Series 100 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Instantaneous On-state Voltage (V) (K/W) Fig. 9 - On-State Voltage Drop Characteristics 0.1 Transient Thermal Impedance Z thJ-hs Steady State Value R thJ-hs = 0.042 K/W (Single Side Cooled) R thJ-hs = 0.021 K/W (Double Side Cooled) 0.01 (DC Operation) ST1280C..K Series 0.001 0.001 0.01 0.1 1 10 100 Square Wave Pulse Duration (s) Fig. 10 - Thermal Impedance ZthJ-hs Characteristics Document Number: 93718 Revision: 11-Aug-08 For technical questions, contact: [email protected] www.vishay.com 5 ST1280C..K Series Vishay High Power Products Phase Control Thyristors (Hockey PUK Version), 2310 A 10 Rectangular gate pulse a) Recommended load line for rated di/dt : 20V, 10ohms; tr<=1 µs b) Recommended load line for <=30% rated di/dt : 10V, 10ohms tr<=1 µs (1) PGM = 16W, tp = 4ms (2) PGM = 30W, tp = 2ms (3) PGM = 60W, tp = 1ms (a ) (b ) 0.1 0.001 T j= -4 0 °C VG D IG D Tj= 2 5 ° C 1 Tj= 12 5 °C Instantaneous Gate Voltage (V) 100 ( 1 ) (2) (3) Frequency Limited by PG(AV) Device: ST1280C..K Series 0.01 0.1 1 10 100 Instantaneous Gate Current (A) Fig. 11 - Gate Characteristics ORDERING INFORMATION TABLE Device code ST 128 0 C 06 K 1 - 1 2 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic PUK 5 - Voltage code x 100 = VRRM (see Voltage Ratings table) 6 - K = PUK case A-24 (K-PUK) 7 - 0 = Eyelet terminals (gate and auxiliary cathode unsoldered leads) 1 = Fast-on terminals (gate and auxiliary cathode unsoldered leads) 2 = Eyelet terminals (gate and auxiliary cathode soldered leads) 3 = Fast-on terminals (gate and auxiliary cathode soldered leads) 8 - Critical dV/dt: None = 500 V/µs (standard selection) L = 1000 V/µs (special selection) LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com 6 http://www.vishay.com/doc?95081 For technical questions, contact: [email protected] Document Number: 93718 Revision: 11-Aug-08 Outline Dimensions Vishay Semiconductors A-24 (K-PUK) DIMENSIONS in millimeters (inches) Creepage distance: 28.88 (1.137) minimum Strike distance: 17.99 (0.708) minimum 1 (0.04) MIN. 2 places 47.5 (1.87) DIA. MAX. 2 places Pin receptable AMP. 60598-1 27.5 (1.08) MAX. 67 (2.6) DIA. MAX. 20° ± 5° 74.5 (2.9) DIA. MAX. 4.75 (0.2) NOM. 44 (1.73) 2 holes DIA. 3.5 (0.14) x 2.1 (0.1) deep Quote between upper and lower pole pieces has to be considered after application of mounting force (see thermal and mechanical specification) Document Number: 95081 Revision: 02-Aug-07 For technical questions, contact: [email protected] www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000