Bulletin I25193 rev. B 04/00 ST300C..L SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features 560A Center amplifying gate Metal case with ceramic insulator International standard case TO-200AC (B-PUK) Typical Applications DC motor controls Controlled DC power supplies AC controllers case style TO-200AC (B-PUK) Major Ratings and Characteristics Parameters ST300C..L Units 560 A 55 °C 1115 A 25 °C @ 50Hz 8000 A @ 60Hz 8380 A @ 50Hz 320 KA2s @ 60Hz 292 KA2s 400 to 2000 V 100 µs - 40 to 125 °C IT(AV) @ Ths IT(RMS) @ Ths ITSM I 2t V DRM/V RRM tq typical TJ www.irf.com 1 ST300C..L Series Bulletin I25193 rev. B 04/00 ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM/V RRM, max. repetitive VRSM , maximum non- I DRM/I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 400 500 Type number 04 ST300C..L 08 800 900 12 1200 1300 16 1600 1700 18 1800 1900 20 2000 2100 50 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM 2 I t ST300C..L 560 (275) A 180° conduction, half sine wave 55 (75) °C double side (single side) cooled 1115 DC @ 25°C heatsink temperature double side cooled Max. peak, one-cycle 8000 t = 10ms non-repetitive surge current 8380 2 Maximum I t for fusing Maximum I2√t for fusing V T(TO) 1 Low level value of threshold voltage V T(TO) 2 High level value of threshold A reapplied 6730 t = 10ms 100% VRRM 7040 t = 8.3ms reapplied Sinusoidal half wave, t = 10ms No voltage Initial TJ = TJ max. t = 8.3ms reapplied 320 2 KA s 226 t = 10ms 100% VRRM 207 t = 8.3ms reapplied 3200 KA2√s Low level value of on-state V (I > π x IT(AV)),T J = TJ max. 0.98 High level value of on-state slope resistance mΩ (I > π x IT(AV)),TJ = TJ max. 0.73 V TM Max. on-state voltage 2.18 IH Maximum holding current 600 IL Typical latching current 1000 2 (16.7% x π x IT(AV) < I < π x IT(AV)), T J = TJ max. 0.74 slope resistance r t2 t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. 0.97 voltage r t1 No voltage t = 8.3ms 292 I 2√ t Units Conditions V mA Ipk= 1635A, TJ = TJ max, tp = 10ms sine pulse T J = 25°C, anode supply 12V resistive load www.irf.com ST300C..L Series Bulletin I25193 rev. B 04/00 Switching Parameter di/dt ST300C..L Max. non-repetitive rate of rise 1000 of turned-on current t d Units Conditions Typical delay time A/µs 1.0 µs tq Typical turn-off time 100 Gate drive 20V, 20Ω, t ≤ 1µs r TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di g/dt = 1A/µs V = 0.67% VDRM, T J = 25°C d ITM = 550A, TJ = TJ max, di/dt = 40A/µs, VR = 50V dv/dt = 20V/µs, Gate 0V 100Ω, tp = 500µs Blocking Parameter ST300C..L Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/µs TJ = TJ max, linear to 80% rated VDRM IRRM IDRM Max. peak reverse and off-state leakage current 50 mA TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM ST300C..L Maximum peak gate power PG(AV) Maximum average gate power IGM Max. peak positive gate current +VGM Maximum peak positive 3.0 Maximum peak negative VGT DC gate voltage required to trigger TJ = TJ max, t ≤ 5ms V T J = TJ max, tp ≤ 5ms p 5.0 TYP. MAX. 200 - 100 200 50 - TJ = - 40°C 2.5 - 1.8 3.0 1.1 - mA TJ = 25°C TJ = 125°C TJ = - 40°C V Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = 25°C TJ = 125°C IGD DC gate current not to trigger 10.0 mA VGD DC gate voltage not to trigger 0.25 V www.irf.com p TJ = TJ max, f = 50Hz, d% = 50 A DC gate current required to trigger TJ = TJ max, t ≤ 5ms 20 gate voltage IGT W 2.0 gate voltage -VGM Units Conditions 10.0 TJ = TJ max Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied 3 ST300C..L Series Bulletin I25193 rev. B 04/00 Thermal and Mechanical Specification Parameter ST300C..L TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJ-hs Max. thermal resistance, 0.011 case to heatsink K/W 0.006 Mounting force, ± 10% wt DC operation single side cooled K/W 0.05 RthC-hs Max. thermal resistance, Approximate weight Case style Conditions °C 0.11 junction to heatsink F Units 9800 N (1000) (Kg) 250 g TO - 200AC (B-PUK) DC operation double side cooled DC operation single side cooled DC operation double side cooled See Outline Table ∆RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Single Side Double Side Single Side Double Side 180° 0.012 0.010 0.008 0.008 120° 0.014 0.015 0.014 0.014 90° 0.018 0.018 0.019 0.019 60° 0.026 0.027 0.027 0.028 30° 0.045 0.046 0.046 0.046 Units Conditions TJ = TJ max. K/W Ordering Information Table Device Code ST 30 0 C 20 L 1 1 2 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - L = Puk Case TO-200AC (B-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/µsec (Standard value) L 4 = 1000V/µsec (Special selection) www.irf.com ST300C..L Series Bulletin I25193 rev. B 04/00 Outline Table 34 (1.34) DIA. MAX. 0.7 (0.03) MIN. 27 (1 .0 6 ) M AX . TWO PLACES PIN RECEPTACLE AMP. 60598-1 53 (2.09) DIA. MAX. 0.7 (0.03) MIN. 6.2 (0.24) MIN. 20°± 5° 5 8. 5 (2 .3 ) D I A . M A X . 4.7 (0.18) Case Style TO-200AC (B-PUK) 36.5 (1.44) All dimensions in millimeters (inches) Quote between upper and lower pole pieces has to be considered after application of Mounting Force (see Thermal and Mechanical Specification) 2 HOLES DIA. 3.5 (0.14) x 2.5 (0.1) DEEP 130 ST300C..L Series (Single Side Cooled) R thJ-hs (DC) = 0.11 K/W 120 110 100 90 Conduction Angle 80 70 30˚ 60 60˚ 90˚ 120˚ 50 180˚ 40 30 0 100 200 300 400 500 Average On-state Current (A) Fig. 1 - Current Ratings Characteristics www.irf.com Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C) CREPAGE DISTANCE 36.33 (1.430) MIN. STRIKE DISTANCE 17.43 (0.686) MIN. 130 ST300C..L Series (Single Side Cooled) R thJ-hs (DC) = 0.11 K/W 120 110 100 90 80 Conduction Period 70 60 30˚ 50 60˚ 40 90˚ 120˚ 30 20 0 180˚ DC 100 200 300 400 500 600 700 Average On-state Current (A) Fig. 2 - Current Ratings Characteristics 5 ST300C..L Series ST300C..L Series (Double Side Cooled) R thJ-hs (DC) = 0.05 K/W 120 110 100 90 Conduction Angle 80 70 60 30˚ 60˚ 40 90˚ 120˚ 30 180˚ 20 0 1600 200 400 600 800 1200 1000 90 Conduction Period 80 70 60 30˚ 60˚ 50 90˚ 40 120˚ 180˚ 30 DC 20 0 200 400 600 800 1000 1200 Fig. 4 - Current Ratings Characteristics 600 Conduction Angle 400 ST300C..L Series T J = 125˚C 200 0 100 200 300 400 500 600 700 1800 DC 1600 180˚ 120˚ 1400 90˚ 60˚ 1200 30˚ 1000 RMS Limit 800 Conduction Period 600 400 ST300C..L Series T J = 125˚C 200 0 0 200 400 600 800 1000 1200 Average On-state Current (A) Average On-state Current (A) Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics 7500 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge. Initial Tj = 125˚C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 7000 6500 6000 5500 5000 4500 4000 3500 ST300C..L Series 3000 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled 6 100 Fig. 3 - Current Ratings Characteristics 800 0 ST300C..L Series (Double Side Cooled) R thJ-hs (DC) = 0.05 K/W 120 110 Average On-state Current (A) 180˚ 120˚ 90˚ 60˚ 30˚ RMS Limit 1400 130 Average On-state Current (A) Maximum Average On-state Power Loss (W) 50 Maximum Allowable Heatsink Temperature (°C) 130 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) Maximum Average On-state Power Loss (W) Maximum Allowable Heatsink Temperature (°C) Bulletin I25193 rev. B 04/00 8000 7500 7000 6500 6000 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial Tj = 125˚C No Voltage Reapplied Rated Vrrm Reapplied 5500 5000 4500 4000 3500 ST300C..L Series 3000 0.01 0.1 1 Pulse Train Duration (s) Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled www.irf.com ST300C..L Series Bulletin I25193 rev. B 03/00 Instantaneous On-state Current (A) 10000 TJ = 25˚C TJ = 125˚C 1000 ST300C..L Series 100 0 1 2 3 4 5 6 7 8 9 Instantaneous On-state Voltage (V) 100 Rectangular gate pulse a) Recommended load line for rated di/dt : 20V, 10ohms; tr<=1 µs b) Recommended load line for <=30% rated di/dt : 10V, 10ohms 10 tr<=1 µs (1) PGM = 10W, (2) PGM = 20W, (3) PGM = 40W, (4) PGM = 60W, tp = 4ms tp = 2ms tp = 1ms tp = 0.66ms (a) (b) VGD 0.1 0.001 Tj=-40 ˚C 1 T j=25 ˚ C Tj=125 ˚ C Transient Thermal Impedance Z thJ-hs (K/W) Fig. 9 - On-state Voltage Drop Characteristics (1) (2) (3) (4) IGD Device: ST300C..L Series 0.01 0.1 Frequency Limited by PG(AV) 1 10 100 Square Wave Pulse Duration (s) Fig. 10 - Thermal Impedance ZthJ-hs Characteristics Instantaneous Gate Voltage (V) 1 Steady State Value R thJ-hs = 0.11 K/W (Single Side Cooled) 0.1 R thJ-hs = 0.05 K/W (Double Side Cooled) (DC Operation) 0.01 ST300C..L Series 0.001 0.001 0.01 0.1 Instantaneous Gate Current (A) 1 10 Fig. 11 - Gate Characteristics www.irf.com 7