TI TAS5261DKDRG4

TM
TAS5261
www.ti.com
SLES188 – AUGUST 2006
315-W Mono BTL Digital Amplifier Power Stage
FEATURES
•
•
•
•
•
•
•
•
Total Output Power
– 125 W Into 8 Ω at <0.09% THD+N
– 220 W Into 6 Ω at 10% THD+N
– 315 W Into 4 Ω at 10% THD+N
110-dB SNR (A-Weighted with TAS5518
modulator)
Supports Pulse-Width Modulation (PWM)
Frame Rates of 192 kHz to 384 kHz
Resistor-Programmable Current Limit
Integrated Self-Protection Circuit Including:
– Under Voltage Protection
– Over Temperature Warning and Error
– Over Load Protection
– Short Circuit (OC) Protection
– PWM Activity Dectector
Power-On Reset (POR) to Eliminate System
Power-Supply Sequencing
Thermally-Enhanced Package DKD (36-pin
PSOP3)
EMI Compliant When Used With
Recommended System Design
Error Reporting 3.3-V and 5-V Compliant
APPLICATIONS
•
•
•
•
AV Receivers
DVD Receivers
Mini/Micro Component Systems
Home Theater Systems
The TAS5261 has complete protection circuitry
integrated on chip, safeguarding the device and
speakers against fault conditions that could damage
the system. These protection features are
short-circuit protection, overcurrent protection,
undervoltage protection, and a loss of pulse-width
modulation (PWM) input signal (PWM Activity
Detector).
A power-on reset (POR) circuit is used to eliminate
power-supply sequencing that is normally required
for most H-bridge designs.
OUTPUT POWER
vs
PVDD_x SUPPLY VOLTAGE
330
TC = 75°C
THD+N at 10%
300
270
PO − Output Power − W
•
240
210
6Ω
180
150
4Ω
120
90
60
8Ω
30
0
0
5
10
15
20
25
30
35
40
45
50
PVDD Supply Voltage − V
G001
DESCRIPTION
The TAS5261 is a high-performance, integrated
mono digital amplifier power stage designed to drive
4-Ω to 8-Ω speakers with low harmonic distortion.
This system requires only a simple, passive
demodulation
filter
to
deliver
high-quality,
high-efficiency audio amplification.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006, Texas Instruments Incorporated
TAS5261
www.ti.com
SLES188 – AUGUST 2006
DEVICE INFORMATION
The TAS5261 is available in a thermally-enhanced 36-pin PSOP3 PowerPAD™ package. The heat slug is
located on the top side of the device for convenient thermal coupling to a heat sink.
DKD PACKAGE
(TOP VIEW)
BST_A
GVDD_A
OTW
SD
RESET
PWM_A
OC_ADJ
GND
AGND
VREG
M3
M2
M1
PWM_B
VDD
GND
GVDD_B
BST_B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
PVDD_A
PVDD_A
PVDD_A
PGND
PGND
PGND
OUT_A
OUT_A
OUT_A
OUT_B
OUT_B
OUT_B
PGND
PGND
PGND
PVDD_B
PVDD_B
PVDD_B
P0018-02
2
Submit Documentation Feedback
TAS5261
www.ti.com
SLES188 – AUGUST 2006
DISSIPATION RATINGS
PARAMETER
CONDITION
TYPICAL (DKD)
RθJC
BTL channel (four transistors)
0.6°C/W
RθJC
One transistor
2.38°C/W
80 mm2
Pad area
Protection Mode
Protection modes are selected by shorting M1, M2, and M3 to VREG or GND.
Table 1. Protection Modes
MODE PINS
PROTECTION MODE
M3 (1)
M2
M1
0
0
0
0
0
1
Reserved
0
1
0
OC latching mode
0
1
1
Reserved
(1)
Full protection (default)
M3 is reserved and always should be connected to board GND.
Submit Documentation Feedback
3
TAS5261
www.ti.com
SLES188 – AUGUST 2006
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
PIN NO.
AGND
9
I
Analog ground
BST_A
1
P
Bootstrap, A side
BST_B
18
I
Bootstrap, B side
GND
8, 16
I
Power ground
GVDD_A
2
P
Gate-drive voltage supply, A side
GVDD_B
17
I
Gate-drive voltage supply, B side
M1
13
I
Mode-selection 1 (LSB)
M2
12
I
Mode-selection 2 (MSB)
M3
11
I
Reserved
OC_ADJ
7
I
Overcurrent threshold programming
OTW
3
O
Overtemperature warning. Open drain, active low.
OUT_A
28, 29, 30
O
Output, half-bridge A
OUT_B
25, 26, 27
O
Output, half-bridge B
PGND
22, 23, 24, 31,
32, 33
P
Power ground
6
I
PWM for half-bridge A
PWM_A
PWM_B
14
I
PWM Input for half-bridge B
PVDD_A
34, 35, 36
P
PVDD supply for half-bridge A
PVDD_B
19, 20, 21
P
PVDD supply for half-bridge B
5
I
Reset. Active low.
SD
4
O
Shutdown. Open drain, active low.
VDD
15
I
Input power supply
VREG
10
O
Internal voltage regulator
RESET
4
I/O
NAME
Submit Documentation Feedback
TAS5261
www.ti.com
SLES188 – AUGUST 2006
GVDD (12 V) and VDD (12 V)
GND
PWM_B
RESET
M2
Shutdown
M1
Hardwire
Mode
Control
H-Bridge OC_ADJ
Output
VDD
VREG
GND
GVDD_A, B
PVDD_A, B
GND_A, B
Mono
BTL
H-Bridge
Overtemp_warning
Right
Output
PWM_A
R2
Left
Output
M3
OUT_A
OUT_B
2nd-Order
L-C Output
Filter for
Each
H-Bridge
4–8 W
(3 W Min)
BST_A
BST_B
Bootstrap
Capacitors
RESET_H-Bridge
RESET
SD
OTW
SD
PWM_B
6
50 V
PVDD (0–50 V)
System
Power
Supplies
GND
12 V
6
PVDD
Power-Supply
Decoupling
VDD
VREG
GND
M3
OUT_A
OUT_B
2nd-Order
L-C Output
Filter for
Each
H-Bridge
4–8 W
(3 W Min)
BST_A
GND
M2
GND_A, B
PVDD_A, B
M1
Hardwire
Mode
Control
GVDD_A, B
Mono
BTL
H-Bridge
H-Bridge
Output
L2
PWM_A
OC_ADJ
L1
Shutdown
System
Microcontroller
Overtemp_warning
OTW
RESET
TAS55XX
R1
2
6
GND
6
Hardwire
Overcurrent
Limit
GVDD, VDD,
and VREG
Power-Supply
Decoupling
PVDD
Power-Supply
Decoupling
PVDD (0–50 V)
BST_B
Bootstrap
Capacitors
2
GVDD, VDD,
and VREG
Power-Supply
Decoupling
Hardwire
Overcurrent
Limit
GND
GVDD (12 V) and VDD (12 V)
AC
B0101-01
Figure 1. Typical System Block Diagram
Submit Documentation Feedback
5
TAS5261
www.ti.com
SLES188 – AUGUST 2006
OTW
M1
M2
M3
PROTECTION & I/O LOGIC
SD
VDD
POWER-UP
RESET
UVP
VREG
VREG
AGND
TEMP
SENSE
GVDD_A GVDD_B
GND
OVER-LOAD
PROT .
CURRENT
SENSE
CB3C
OC_ADJ
RESET
GVDD _B
PWM
ACTIVITY
DETECTOR
BST_B
PVDD_B (x3)
PWM_B
PWM
RECEIVER
CONTROL
TIMING
CONTROL
GATE-DRIVE
OUT_B (x3)
PGND (x3)
GVDD _A
BST_A
PVDD_A (x3)
PWM_A
PWM
RECEIVER
CONTROL
TIMING
CONTROL
GATE-DRIVE
OUT_A (x3)
PGND (x3)
Figure 2. Functional Block Diagram
6
Submit Documentation Feedback
TAS5261
www.ti.com
SLES188 – AUGUST 2006
ORDERING INFORMATION
TA
PACKAGE
DESCRIPTION
0°C to 70°C
TAS5261DKD
36-pin PSOP3
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
VDD to AGND
–0.3
13.2
V
GVDD_x to AGND
–0.3
13.2
V
PVDD_x to
PGND_x (2)
–0.3
71
V
OUT_x to PGND_x (2)
–0.3
71
V
BST_x to PGND_x (2)
–0.3
79.7
V
GVDD_x (2)
BST_x to
–0.3
66.5
V
VREG to AGND
–0.3
4.2
V
PGND_x to GND
–0.3
0.3
V
PGND_x to AGND
–0.3
0.3
V
GND to AGND
–0.3
0.3
V
PWM_x, OC_ADJ, M1, M2, M3 to AGND
–0.3
4.2
V
RESET, SD, OTW to AGND
–0.3
7
V
9
mA
0
150
°C
–65
150
°C
260
°C
Maximum continuous sink current (SD, OTW)
Maximum operating junction temperature range, TJ
Storage temperature range, Tstg
Lead temperature 1,6 mm (1/16 in) from case for 10 s
Minimum pulse duration, low – minimum pulse width must be ensured by the PWM processor
(1)
(2)
50
ns
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are only stress
ratings, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
These voltages represent the dc voltage + peak ac waveform measured at the terminal of the device in all conditions.
Submit Documentation Feedback
7
TAS5261
www.ti.com
SLES188 – AUGUST 2006
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
0
50
52.5
V
Gate-drive power supply
10.8 (1)
12
13.2
V
VDD
Digital regulator supply voltage
10.8 (1)
12
13.2
RL
Resistive load impedance, bridge-tied load (BTL)
RL
Resistive load impedance, BTL, ROC = 22kΩ, PVDD = 50V, (no current limiting)
3
LDEM
Minimum output filter inductance under both operating and short-circuit conditions,
with appropriate OC_ADJ resistor value
5
fS
PWM frame rate
t(low)
Minimum low-state pulse duration per PWM frame, noise shaper enabled
CBS
Bootstrap capacitor, selected value supports fs = 192 kHz to 384 kHz
33
nF
RBS
Bootstrap series resistor - 1/4 W
1.5
Ω
4.7
Ω
470
pF
15
nS
PVDD_x
Half-bridge supply voltage
GVDD_x
Ω
Bootstrap snubber - 1/4 W
DCLMP
Ultra-Fast Recovery Clamping Diode, Average forward current = 1A, Maximum
repetitive reverse voltage = 200V (ES1D, mfg:Fairchild)
DTVS
Transient Voltage Suppressor, 600W @ 1mS (P6SMB62AT3, mfg: ON Semiconductor)
CPVDD
PVDD Close Decoupling Capacitor, two capacitors
RAGND
AGND resistor - 1/4 W
R
Optional external pullup resistor to +3.3V or +5 V for SD and OTW
TJ
Junction temperature
µH
10
192
RCBS
(1)
V
Ω
4-16
384
50
3.3
kHz
ns
62
V
100
nF
3.3
Ω
4.7
kΩ
0
125
°C
GVDD operation below 10.8 V significantly reduces efficiency of the output MOSFET stage and requires a larger heatsink. For the
purpose of noise margin, the UVP level is set lower to provide an increased noise margin, however, TI recommends a nominal dc
voltage of 12 V for GVDD.
AUDIO CHARACTERISTICS
Audio frequency = 1 kHz, PVDD_x = 50 V, GVDD_x = 12 V, VDD = 12 V, RL = 8 Ω , fs = 384 kHz, OC_ADJ = 22 kΩ,
TC= 75°C, output filter is LDEM = 10 µH, CL = 1 µF (unless otherwise noted). Audio performance is recorded as a chipset,
TAS5518 as front end with an effective modulation index of 96.1% and TAS5261 as the power stage. PCB and system
configuration are in accordance with recommended design guidelines.
PARAMETER
PO
MIN
TYP
125
RL = 6 Ω, f = 1 kHz
165
RL = 4 Ω, f = 1 kHz
235
RL = 8 Ω, f = 1 kHz, THD = 10%
165
RL = 6 Ω, f = 1 kHz, THD = 10%
220
RL = 4 Ω, f = 1 kHz, THD = 10%
315
MAX
UNIT
W
PO
Maximum power output
RL = 3 Ω, f = 1 kHz, CBC allowed
400
THD+N
Total harmonic distortion + noise,
AES 17 filter
1 W to 125 W, RL=8 Ω, AES17 filter,
Unclipped
0.09
%
SNR
Signal-to-noise ratio (1)
Ratio of 1-FFS to 0-FFS input,
A-weighted filter
110
dB
DNR
Dynamic range
–60-dBFS input, A-weighted filter
110
dB
VOO
Output offset voltage
PWM switching frequency 384 kHz,
Measured on speaker terminals
Pidle
Power dissipation due to idle losses
(IPVDD_X)
PO = 0 W, Output switching (2)
(1)
(2)
8
Unclipped power output
TEST CONDITIONS
RL = 8 Ω, f = 1 kHz
SNR is calculated relative to the 0 dBFS input level.
Actual system idle losses are also affected by core losses of output inductors.
Submit Documentation Feedback
–15
W
15
2
mV
W
TAS5261
www.ti.com
SLES188 – AUGUST 2006
ELECTRICAL CHARACTERISTICS
Audio frequency = 1 kHz, PVDD_x = 50 V, GVDDx = 12 V, VDD = 12 V, RL = 8 Ω , fs = 384 kHz, OC_ADJ = 22 kΩ,
TC = 75°C, output filter is LDEM = 10 µH, CL = 1 µF (unless otherwise noted). AC performance is recorded as a chipset,
TAS5518 as front end with an effective modulation index of 96.1% and TAS5261 as the power stage. PCB and system
configuration are in accordance with recommended design guidelines.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
Internal Voltage Regulator and Current Consumption
VREG
Voltage regulator,
only used as reference node
IVDD
VDD supply current
IGVDD_x
GVDD_x gate-supply current
per half bridge
IPVDD_x
Half-bridge idle current
3.3
Operating, 50% duty cycle
7.7
Idle, reset mode
6.7
V
mA
50% duty cycle
15
Idle, reset mode
1.5
50% duty cycle
23
mA
100
µA
Reset mode (RESET = 1),
No switching
mA
Output-Stage MOSFETs
RDSON,LS
Drain-to-source resistance, low side
TJ = 25°C, LDMOS only
40
mΩ
RDSON,HS
Drain-to-source resistance, high side
TJ = 25°C, LDMOS only
40
mΩ
I/O Protection
VUVP,POS
Undervoltage protection limit, GVDD_x
8.5
V
OTW
Overtemperature warning
125
°C
OTWhys
OTW hysteresis
25
°C
OTE
Overtemperature error threshold
155
°C
OTEhys
OTE hysteresis
30
°C
OTE-OTW
differential
Temperature delta between OTW and OTE
30
°C
OLPC
Overload protection time constant
(1)
fPWM = 384 kHz
20
Resistor programmable high end
with OC_ADJ = 22 kΩ (1)
15
ms
IOC
Overcurrent limit response
ROC
Programming resistor
RPD
Pulldown resistor at the output of each
half-bridge
Connected when RESET is high to
provide a charge path for the
bootstrap capacitor
2.5
kΩ
PWM
PWM Activity Detector
Lack of transition of any PWM input
13
µs
(1)
16
22
17
A
100
kΩ
DC measurement with 1-ms pulse
Submit Documentation Feedback
9
TAS5261
www.ti.com
SLES188 – AUGUST 2006
ELECTRICAL CHARACTERISTICS
GVDD_x = 12 V ± 10%, VDD = 12 V ± 10%, TJ = 25°C (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
Logic-Level and Open-Drain Outputs
VIH
High-level input voltage
Static
VIL
Low-level input voltage
Static
Ilkg (1)
Input leakage current
0.8
45
65
Static, Low PWM_A, Low PWM_B,
Low M1, Low M2, Low M3
–10
10
Static, High RESET
20
40
Static, Low RESET
–70
–50
Internal pulldown to AGND
for PWM_A and PWM_B inputs
RINT-PU
Internal pullup resistance on OTW and SD
VOH
High-level output voltage
VOL
Low-level output voltage
IO = 4 mA
FANOUT
Device fanout (OTW, SD)
External pullup to 5 V
10
V
Static, High PWM_A, High PWM_B,
High M1, High M2, High M3
RINT-PD
(1)
2
50
20
Internal pullup resistor
2.4
VREG
External pullup of 3.3 kΩ to 5 V
2.5
4.9
Submit Documentation Feedback
33
0.4
10
µA
kΩ
Resistor to VREG
Pullup and pulldown resistors affect the leakage current.
28
V
kΩ
V
V
Devices
TAS5261
www.ti.com
SLES188 – AUGUST 2006
TYPICAL CHARACTERISTICS
blk
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
10
5
2
1
0.5
T
H
D
+
N
%
0.2
0.1
0.05
0.02
0.01
80m
200m
500m
1
2
5
10
20
50
100
200
300
Output Power W
Red - 4 Ohm
Blue - 6 Ohm
Magenta - 8 Ohm
Figure 3.
OUTPUT POWER
vs
PVDD_x SUPPLY VOLTAGE
UNCLIPPED OUTPUT POWER
vs
PVDD_x SUPPLY VOLTAGE
330
250
TC = 75°C
THD+N at 10%
300
270
200
240
PO − Output Power − W
PO − Output Power − W
TC = 75°C
225
210
6Ω
180
150
4Ω
120
90
175
150
6Ω
125
4Ω
100
75
50
60
8Ω
30
8Ω
25
0
0
0
5
10
15
20
25
30
35
40
45
50
0
PVDD Supply Voltage − V
5
10
15
20
25
30
35
40
45
50
PVDD Supply Voltage − V
G001
Figure 4.
G003
Figure 5.
Submit Documentation Feedback
11
TAS5261
www.ti.com
SLES188 – AUGUST 2006
TYPICAL CHARACTERISTICS
(continued)
blk
SYSTEM EFFICIENCY
vs
OUTPUT POWER
SYSTEM POWER LOSS
vs
OUTPUT POWER
100
12
TC = 25°C
11
10
80
8
Power Loss − W
Efficiency − %
9
60
40
7
6
5
4
3
20
2
TC = 25°C
Two Channels
1
0
0
0
20
40
60
80
100
120
PO − Output Power − W
0
25
50
G004
Figure 6.
Figure 7.
SYSTEM OUTPUT POWER
vs
CASE TEMPERATURE
350
4Ω
PO − Output Power − W
300
250
6Ω
200
8Ω
150
100
50
THD+N at 10%
0
0
25
50
75
100
TC − Case Temperature − °C
Figure 8.
12
75
PO − Output Power − W
Submit Documentation Feedback
125
G006
100
125
G005
TAS5261
www.ti.com
SLES188 – AUGUST 2006
TYPICAL CHARACTERISTICS
(continued)
blk
NOISE AMPLITUDE
vs
FREQUENCY
+0
-5
-10
-15
-20
-25
-30
-35
-40
N
o
i
s
e
-45
-50
-55
-60
A
m
p
l
i
t
u
d
e
-65
-70
-75
-80
-85
-90
-
-95
d
B
r
-100
-105
-110
-115
-120
-125
-130
-135
-140
-145
-150
0
1k
2k
3k
4k
5k
6k
7k
8k
9k
10k
11k
12k
13k
14k
15k
16k
17k
18k
19k
20k
21k
22k
f - Frequency - kHz
Figure 9.
Submit Documentation Feedback
13
TAS5261
www.ti.com
SLES188 – AUGUST 2006
APPLICATION INFORMATION
Typical Application Schematic
14
Submit Documentation Feedback
TAS5261
www.ti.com
SLES188 – AUGUST 2006
APPLICATION INFORMATION (continued)
Recommended Printed Circuit Board (PCB) Layout
PCB Requirements
•
•
2-oz copper (FR-4) recommended
PVDD voltage and capacitor selection in accordance with the data sheet
Figure 10. PCB (Top Layer)
Figure 11. PCB (Bottom Layer)
Submit Documentation Feedback
15
TAS5261
www.ti.com
SLES188 – AUGUST 2006
THEORY OF OPERATION
Power Supplies
To facilitate system design, the TAS5261 needs only
a 12-V supply in addition to a typical 50-V
power-stage supply. An internal voltage regulator
provides suitable voltage levels for the digital and
low-voltage analog circuitry. Additionally, all circuitry
requiring a floating voltage supply, e.g., the high-side
gate drive, is accommodated by built-in bootstrap
circuitry requiring only a few external capacitors.
To provide outstanding electrical and acoustic
characteristics, the PWM signal path, including gate
drive and output stage, is designed as identical,
independent half bridges. For this reason, each half
bridge has separated gate-drive supply (GVDD_x),
bootstrap pins (BST_x) and power-stage supply pins
(PVDD_x). Furthermore, an additional pin (VDD) is
provided as power supply for all common circuits.
Although supplied from the same 12-V source, it is
highly recommended to separate GVDD_x and VDD
on the printed circuit board (PCB) by RC filters (see
application diagram for details). These RC filters
provide the recommended high-frequency isolation.
Special attention should be paid to placing all
decoupling capacitors as close to their associated
pins as possible. In general, inductance between the
power-supply pins and decoupling capacitors must
be avoided. (See reference board documentation for
additional information.)
For a properly functioning bootstrap circuit, a small
ceramic capacitor must be connected from each
bootstrap pin (BST_x) to the power-stage output pin
(OUT_x). When the power-stage output is low, the
bootstrap capacitor is charged through an internal
diode
connected
between
the
gate-drive
power-supply pin (GVDD_x) and the bootstrap pin.
When the power-stage output voltage is high, the
bootstrap capacitor voltage is shifted above the
output voltage potential and, thus, provides a
suitable voltage supply for the high-side gate driver.
In an application with PWM switching frequencies in
the range of 352 kHz to 384 kHz, it is recommended
to use 33-nF ceramic capacitors, size 0603 or 0805,
for the bootstrap capacitor. These 33-nF capacitors
ensure sufficient energy storage, even during
minimal PWM duty cycles, to keep the high-side
power-stage FET (LDMOS) fully started during all of
the remaining part of the PWM cycle. In an
application running at a reduced switching frequency,
generally 250 kHz to 192 kHz, the bootstrap
capacitor might need to be increased in value.
Special attention should be paid to the power-stage
power supply – this includes component selection,
16
PCB placement, and routing. As indicated, each half
bridge has independent power-stage supply pins
(PVDD_x). For optimal electrical performance, EMI
compliance, and system reliability, it is important that
each PVDD_x pin is decoupled with two 100-nF
ceramic capacitors placed as close as possible to
each supply pin on the same side of the PCB as the
TAS5261 location. It is recommended to follow the
PCB layout of the TAS5261 reference design. For
additional information on the recommended power
supply and required components, see the application
diagrams given in this data sheet.
The 12-V supply should be powered from a
low-noise, low-output-impedance voltage regulator.
Likewise, the 50-V power-stage supply is assumed to
have low output impedance and low noise. The
internal POR circuit eliminates the need for
power-supply sequencing. Moreover, the TAS5261 is
fully protected against erroneous power-stage turn
on due to parasitic gate charging. Thus,
voltage-supply ramp rates (dv/dt) are noncritical
within the specified range (see the Recommended
Operating Conditions section of this data sheet).
System Power-Up/Power-Down Sequence
Powering Up
There is no power-up sequence is required for the
TAS5261. The outputs of the H-bridge remain in a
high-impedance state until the gate-drive supply
voltage (GVDD_x) and VDD voltage are above the
undervoltage protection (UVP) voltage threshold (see
the Electrical Characteristics section of this data
sheet). Although not specifically required, it is
recommended to hold RESET in a low state while
powering up the device. This allows an internal
circuit to charge the external bootstrap capacitors by
enabling a weak pulldown of the half-bridge output.
While powering up the TAS5261, RESET should be
held low.
Powering Down
There is no power-down sequence is required for the
TAS5261. The device remains fully operational as
long as the gate-drive supply (GVDD_x) voltage and
VDD voltage are above the undervoltage protection
(UVP) threshold level (see the Electrical
Characteristics section of this data sheet). Although
not specifically required, it is a good practice to hold
RESET low during power down, thus, preventing
audible artifacts including pops and clicks.
Submit Documentation Feedback
TAS5261
www.ti.com
SLES188 – AUGUST 2006
Error Reporting
The SD and OTW pins are both active-low,
open-drain
outputs.
Their
function
is
for
protection-mode signaling to a PWM controller or
other system-control device. Any fault resulting in
device shutdown is signaled by the SD pin going low.
Likewise, OTW goes low when the device junction
temperature exceeds 115°C. (see Table 2).
Table 2. Error Reporting
SD
OTW
DESCRIPTION
0
0
Over Temperature (OTE) or Over
Load (OLP) or Under Voltage (UVP)
0
1
Over Load (OLP), PWM Activity
Dectector, or Under Voltage (UVP)
1
0
Over Temperature Warning. Junction
temperature higher than 125°C.
1
1
Normal operation. Junction
temperature lower than 125°C.
It should be noted that asserting RESET low forces
the SD and OTW signals high, independent of faults
being present. It is recommended to monitor the
OTW signal using the system microcontroller and
respond to an overtemperature warning signal by, for
example, turning down the volume to prevent further
heating of the device resulting in device shutdown
(OTW). To reduce external component count, an
internal pullup resistor to 3.3 V is provided on both
the SD and OTW outputs. Level compliance for 5-V
logic can be obtained by adding external pullup
resistors to 5 V (see the Electrical Characteristics
section of this data sheet for further specifications).
Device Protection System
The TAS5261 contains advanced protection circuitry
carefully designed to facilitate system integration and
ease of use, as well as safeguarding the device from
permanent failure due to a wide range of fault
conditions, such as short circuit, overload, and
undervoltage. The TAS5261 responds to a fault by
immediately setting the power stage in a
high-impedance state (Hi-Z) and asserting the SD
pin low. In situations other than overload, the device
automatically recovers when the fault condition has
been removed (e.g., the voltage supply has
increased). For highest possible reliability, recovering
from an overload fault requires external reset of the
device no sooner than 1 s after the shutdown (see
the Device Reset section of this data sheet).
Over Current (OC) Protection With Current
Limiting and Overload Detection
The device has independent, fast-reacting current
detectors with programmable trip threshold (OC
threshold) on all high-side and low-side power-stage
FETs. See Table 3 for OC-adjust resistor values. The
detector outputs are closely monitored by two
protection systems. The first protection system
controls the power stage in order to prevent the
output current from further increasing. For instance, it
performs a current-limiting function rather than
prematurely shutting down during combinations of
high-level music transients and extreme speaker
load impedance drops. If the high-current situation
persists, i.e., the power stage is being overloaded, a
second protection system triggers a latching
shutdown, resulting in the power stage being set in
the high-impedance (Hi-Z) state.
Table 3. OC-Adjust Resistor Values
OC-ADJUST
RESISTOR VALUES
(kΩ) (1)
(1)
CURRENT BEFORE OC OCCURS
(A)
MIN
TYP
MAX
22
15
16
17
27
12
13
14
47
7
8
8
68
5
5
6
100
3
4
4
Resistor tolerance is ±5%.
For lowest-cost bill of materials in terms of
component selection, the OC threshold current
should be limited, considering the power output
requirement and minimum load impedance.
Higher-impedance loads require a lower OC
threshold.
The demodulation filter inductor must retain a
minimum of 5-H inductance at twice the selected OC
threshold current.
Most inductors have decreasing inductance with
increasing temperature and increasing current
(saturation). To some degree, an increase in
temperature naturally occurs when operating at high
output currents, due to inductor core losses and the
dc resistance of the inductor copper winding. A
thorough analysis of inductor saturation and thermal
properties is strongly recommended.
Setting the OC threshold too low might cause issues,
such as lack of enough output power and/or
unexpected shutdowns due to sensitive overload
detection.
In general, it is recommended to follow closely the
external component selection and PCB layout as
given in the Application Information section of this
data sheet.
Submit Documentation Feedback
17
TAS5261
www.ti.com
SLES188 – AUGUST 2006
For added flexibility, the OC threshold is
programmable within a limited range using a single
external resistor connected between the OC_ADJ pin
and AGND. It should be noted that a properly
functioning overcurrent detector assumes the
presence of a properly designed demodulation filter
at the power-stage output. Short-circuit protection is
not provided directly at the output pins of the power
stage but only on the speaker terminals (after the
demodulation filter). It is required to follow certain
guidelines when selecting the OC threshold and an
appropriate demodulation inductor.
VDD or GVDD_x pin results in all half-bridge outputs
immediately being set in the high-impedance state
(Hi-Z) and SD being asserted low. The device
automatically resumes operation when all supply
voltages have increased above the UVP threshold.
Over Temperature (OTE) Protection
Asserting RESET input low removes fault
information. A rising-edge transition on the reset
input allows the device to resume operation after an
overload fault.
The
TAS5261
has
a
two-level,
temperature-protection system that asserts an
active-low warning signal (OTW) when the device
junction temperature exceeds the OTW level stated
in the parametric table. If the device junction
temperature exceeds the OTE level stated in the
parametric table, the device is put into thermal
shutdown, resulting in all half-bridge outputs being
set in the high-impedance state (Hi-Z) and SD being
asserted low. OTE is latched in this case. To clear
the OTE latch, reset must be asserted. Thereafter,
the device resumes normal operation.
Under Voltage Protection (UVP) and
Power-On Reset (POR)
The UVP and POR circuits of the TAS5261 fully
protect the device in any power-up/down and
brownout situation. While powering up, the POR
circuit resets the overload circuit (OLP) and ensures
that all circuits are fully operational when the
GVDD_x and VDD supply voltages reach the UVP
level stated in the parametric table. Although
GVDD_x and VDD are independently monitored, a
supply-voltage drop below the UVP threshold on any
Device Reset
When RESET is asserted low, the output FETs in all
half bridges are forced into a high-impedance state
(Hi-Z). During this reset time, a resistor is connected
between OUT_x and PGND pins, in order to charge
the bootstrap capacitor.
PWM Activity Detector
The PWM Activity Detector logic monitors individual
PWM inputs. If one or more inputs are stuck in either
a high state or a low state for more than a defined
length of time, the entire device is shut down.
The PWM Activity Detector is not latched and normal
operation resumes when PWM activity is present on
the PWM inputs. When an invalid PWM frame is
detected, the PWM Activity Detector responds
immediately (no delay). The TAS5261 resumes
operation as soon as valid PWM signals are present.
The PWM Activity Detector is reported as a low on
the SD pin.
Modulation Index Setting
96.1% is the recommended setting for the
modulation index limit of the PWM when driving the
TAS5261. The following shows modulation index
limit registers and setting value in hexadecimal for TI
modulators.
TAS5508/TAS5518: 0x16h at 04h
TAS5086: 0x10h at 04h
18
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TAS5261DKD
ACTIVE
SSOP
DKD
36
29
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
TAS5261DKDG4
ACTIVE
SSOP
DKD
36
29
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
TAS5261DKDR
ACTIVE
SSOP
DKD
36
500
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
TAS5261DKDRG4
ACTIVE
SSOP
DKD
36
500
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-4-260C-72 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated