Chip tantalum capacitors with (Fail-safe open structure type) TCFG series C Case Dimensions (Unit : mm) Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Anode mark (Unit : mm) Dimensions Size L 6.0 + − 0.2 W1 3.2 + − 0.2 W2 2.2 + − 0.1 H 2.5 + − 0.2 S 1.3 + − 0.2 Part No. Explanation T C F G C 1 A 1 0 7 M C R 2 1 1 Series name 4 3 4 TCFG 5 6 Capacitance Nominal capacitance in pF in 3 digits : 2significant figure representing the number of 0's. 2 Case code C 5 Rated voltage (V) CODE 4 6.3 10 16 25 0G 0J 1A 1C 1E Capacitance tolerance M: + − 20% 3 Rated Voltage 6 Taping C : Reel width (12mm) R : Positive electrode on the side opposite to sprocket hole www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 1/6 2012.03 - Rev.G TCFG Series C Case Data Sheet Capacitance range Rated voltage (V.DC) (μF) 4 6.3 10 20 16 15 (156) 25 C 22 (226) 33 (336) 47 (476) C 68 (686) 100 (107) C 150 (157) 220 (227) C C∗ Remark) Case size codes (C) in the above show each size products line-up. ∗ : Under development Marking The indications listed below should be given on the surface of a capacitor. Polarity : The polarity should be shown by Rated DC voltage Nominal capacitance [C Case] bar. (on the anode side) note 1) Visual typical example (1) capacitance code (2) voltage code (1) 100μF (2) 10V 100 10V manufacture code note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 2/6 2012.03 - Rev.G TCFG Series C Case Data Sheet Characteristics Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Operating Temperature −55 °C to +125 °C Voltage reduction when temperature exceeds +85°C Maximum operating temperature +85 °C with no voltage derating 4 6.3 10 16 25 at 85°C Category Voltage (V.DC) 2.5 4 6.3 10 16 at 125°C Surge Voltage 5.0 8 Rated Voltage (V.DC) DC leakage current Capacitance tolerance at 85°C 13 20 32 0.5μA or 0.01CV whichever is greater (Shown in "Standard list") As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1 min Shall be satisfied allowance range. As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit ±20% Tangent of loss angle (Df, tanδ) Shall be satisfied the voltage on "Standard list" As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the voltage on "Standard list" As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality. The indications should be clear. soldering heat L.C Less than initial limit ΔC / C Within ±10% of initial value tanδ Less than 150% of initial limit As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 260±10°C Duration : 5±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Dip in the solder bath Solder temp : 330±5°C Fail-Safe open unit actuation Within 320°C − 20s Temperature cycle Appearance There should be no significant abnormality. L.C Less than initial limit ΔC / C Within ±20% of initial value tanδ Less than 150% of initial limit As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Step Temp. Time 1 −55 + − 3°C 30 + −3min 2 3 4 Room temp. 3min. or less 125 + 30 + − 2°C −3min Room temp. 3min. or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Appearance There should be no significant abnormality. The indications should be clear. L.C Less than initial limit ΔC / C Within ±20% of initial value tanδ Less than 150% of initial limit www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 60±2°C and 90 to 95%RH, respectively, for 500±24h level it at room temperature for over 24h and then measure the sample. 3/6 2012.03 - Rev.G TCFG Series C Case Item Temperature Temp. Stability ΔC / C tanδ Data Sheet −55°C As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 Within 0/−12%of initial value Shall be satisfied the voltage on "Standard list" − L.C Surge Voltage Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Temp. +85°C ΔC / C Within +12/0%of initial value tanδ Shall be satisfied the voltage on "Standard list" L.C Less than 1000% of initial limit Temp. +125°C ΔC / C Within +15/0%of initial value tanδ Shall be satisfied the voltage on "Standard list" L.C Less than 1250% of initial limit As per 4.26 JIS C 5101-1 As per 4.14 JIS C 5101-3 Apply the specified surge voltage every 5±0.5min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. Appearance There should be no significant abnormality. L.C Less than initial value ΔC / C Within ±12%of initial value tanδ Less than 150% of initial limit Loading at Appearance There should be no significant abnormality. High Less than 125% of initial limit temperature L.C Within ±20%of initial value ΔC / C tanδ Terminal Strength As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature/humidity for over 24h and measure the value. Less than 150% of initial limit Capacitance The measured value should be stable. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below.) Appearance There should be no significant abnormality. (Unit : mm) 20 50 F (Apply force) R230 1 Thickness 1.6mm 45 Adhesiveness The terminal should not come off. 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product YAA C105 Apply force a circuit board www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 4/6 2012.03 - Rev.G TCFG Series C Case Data Sheet Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Dimensions Be based on "External dimensions" Measure using a caliper of JIS B 7505 Class 2 or higher grade. Resistance to solvents The indication should be clear. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed = 25±2.5mm/s Pre-treatment (accelerated aging) : Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25%, IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X, Y and Z directions Mounting : The terminal is soldered on a print circuit board. Standard list, TCFG series C Case Part No. Leakage Rated Derated Surge DF 120Hz Impedance current Voltage Voltage Voltage Capacitance (%) 100kHz Case Tolerance 25 °C @85°C @125°C @85°C 120Hz code (%) 1WV.60s −55°C 25°C 125°C (μF) (V) (V) (Ω) (V) (μA) 85°C ∗ TCFG C 0G 227 MCR 4 2.5 5 220 ±20 8.8 30 12 16 1.3 C TCFG C 0J 157 MCR 6.3 4 8 150 ±20 9.5 30 12 16 1.3 C TCFG C 1A 107 MCR 10 6.3 13 100 ±20 10.0 14 10 12 1.3 C TCFG C 1C 476 MCR 16 10 20 47 ±20 7.5 12 8 10 1.6 C 16 ±20 3.8 14 10 12 1.3 C TCFG C 1E 156 MCR 25 16 32 ∗ = Under development www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 5/6 2012.03 - Rev.G TCFG Series C Case Data Sheet Packaging specifications (Unit : mm) Case code C (6032) A B±0.2 W±0.2 E±0.1 F±0.05 +0.1 3.7 −0.2 +0.1 6.4 −0.2 P1±0.1 12 1.75 5.5 8.0 P2±0.05 P0±0.1 D0±0.1 t1±0.05 t2±0.1 2.0 4.0 φ1.5 0.3 3.0 Taping C case t2 Sprocket hole φDo t1 E W P2 P1 P0 A F B Pull out direction Packaging style Packaging Case size C Case Packaging style Taping Plastic taping φ180mm reel Symbol Basic ordering unit CR 500 Reel 13.0 +1.00 Plastic reel φ 180 −1.50 φ 60 +1 0 φ13±0.2 15.4±1.0 Label sticking position (Unit : mm) EIAJ ET - 7200A www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 6/6 2012.03 - Rev.G Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. R1120A