TDA2006 12W AUDIO AMPLIFIER DESCRIPTION The TDA2006 is a monolithic integrated circuit in Pentawatt package, intended for use as a low frequency class ”AB” amplifier. At ±12V, d = 10 % typically it provides 12W output power on a 4Ω load and 8W on a 8Ω . The TDA2006 provides high output current and has very low harmonic and cross-over distortion. Further the device incorporates an original (and patented)short circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the working point of the output transistors within their safe operating area. A conventional thermal shutdown system is also included. The TDA2006 is pin to pin equivalent to the TDA2030. PENTAWATT ORDERING NUMBERS : TDA2006V TDA2006H TYPICAL APPLICATION CIRCUIT May 1995 1/12 TDA2006 SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Parameter Vs Supply Voltage Vi Input Voltage Vi Differential Input Voltage Io Value Unit ± 15 V Vs ± 12 V Output Peak Current (internaly limited) 3 A Ptot Power Dissipation at Tcase = 90 °C 20 W Tstg, Tj Storage and Junction Temperature – 40 to 150 °C Value Unit 3 °C/W THERMAL DATA Symbol R th (j-c) Parameter Thermal Resistance Junction-case PIN CONNECTION 2/12 Max TDA2006 ELECTRICAL CHARACTERISTICS (refer to the test circuit ; VS = ± 12V, Tamb = 25oC unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. ±6 Max. Unit ± 15 V Vs Supply Voltage Id Quiescent Drain Current Vs = ± 15V 40 80 mA Ib Input Bias Current Vs = ± 15V 0.2 3 µA VOS Input Offset Voltage Vs = ± 15V ±8 mV IOS Input Offset Current Vs = ± 15V ± 80 nA VOS Output Offset Voltage Vs = ± 15V ± 10 ± 100 mV Output Power d = 10%, f = 1kHz RL = 4Ω RL = 8Ω Po W 6 12 8 d Distortion Po = 0.1 to 8W, RL = 4Ω, f = 1kHz Po = 0.1 to 4W, RL = 8Ω, f = 1kHz 0.2 0.1 % % Vi Input Sensitivity Po = 10W, R L = 4Ω, f = 1kHz Po = 6W, RL = 8Ω, f = 1kHz 200 220 mV mV B Frequency Response (– 3dB) Po = 8W, RL = 4Ω Ri Input Resistance (pin 1) f = 1kHz Gv Voltage Gain (open loop) f = 1kHz Gv Voltage Gain (closed loop) f = 1kHz eN Input Noise Voltage iN 20Hz to 100kHz 0.5 MΩ 75 dB 30 30.5 dB B (– 3dB) = 22Hz to 22kHz, RL = 4Ω 3 10 µV Input Noise Current B (– 3dB) = 22Hz to 22kHz, RL = 4Ω 80 200 pA Supply Voltage Rejection R L = 4Ω, Rg = 22kΩ, fripple = 100Hz (*) Id Drain Current Po = 12W, R L = 4Ω Po = 8W, RL = 8Ω Tj Thermal Shutdown Junction Temperature SVR 29.5 5 40 50 dB 850 500 mA mA 145 °C (*) Referring to Figure 15, single supply. 3/12 TDA2006 Figure 1 : Output Power versus Supply Voltage Figure 2 : Distortion versus Output Power Figure 3 : Distortion versus Frequency Figure 4 : Distortion versus Frequency Figure 5 : Sensitivity versus Output Power Figure 6 : Sensitivity versus Output Power 4/12 TDA2006 Figure 7 : Frequency Response with different values of the rolloff Capacitor C8 (see Figure 13) Figure 8 : Figure 9 : Quiescent Current versus Supply Voltage Figure 10 : Supply Voltage Rejection versus Voltage Gain Figure 11 : Power Dissipation and Efficiency versus Output Power Value of C8 versus Voltage Gain for different Bandwidths (see Figure 13) Figure 12 : Maximum Power Dissipation versus Supply Voltage (sine wave operation) 5/12 TDA2006 Figure 13 : Application Circuit with Spilt Power Supply Figure 14 : P.C. Board and Components Layout of the Circuit of Figure 13 (1:1 scale) 6/12 TDA2006 Figure 15 : Application Circuit with Single Power Supply Figure 16 : P.C. Board and Components Layout of the Circuit of Figure 15 (1:1 scale) 7/12 TDA2006 Figure 17 : Bridge Amplifier Configuration with Split Power Supply (PO = 24W, VS = ± 12V) PRACTICAL CONSIDERATIONS Printed Circuit Board The layout shown in Figure 14 should be adopted by the designers. If different layout are used, the ground points of input 1 and input 2 must be well decoupled from ground of the output on which a rather high current flows. Assembly Suggestion No electrical isolation is needed between the pack- age and the heat-sink with single supply voltage configuration. Application Suggestion The recommended values of the components are the ones shown on application circuits of Figure 13. Different values can be used. The table 1 can help the designers. Table 1 R1 R2 R3 Recommanded Value 22 kΩ 680 Ω 22 kΩ R4 1Ω Closed Loop Gain Setting Closed Loop Gain Setting Non Inverting Input Biasing Frequency Stability R5 3 R2 Upper Frequency Cut-off C1 2.2 µF Input DC Decoupling C2 22 µF C 3C4 C 5C6 C7 0.1 µF 100 µF 0.22 µF 1 2πBR1 Inverting Input DC Decoupling Supply Voltage by Pass Supply Voltage by Pass Frequency Stability Component C8 D 1D2 1N4001 Purpose Upper Frequency Cut-off Smaller Than Recommanded Value Decrease of Gain (*) Increase of Gain Decrease of Input Impedance Danger of Oscillation Increase of Low Frequencies Cut-off Increase of Low Frequencies Cut-off Danger of Oscillation Danger of Oscillation Danger of Oscillation Lower Bandwidth To Protect the Device Against Output Voltage Spikes. (*) Closed loop gain must be higher than 24dB. 8/12 Larger Than Recommanded Value Increase of Gain Decrease of Gain (*) Increase of Input Impedance Danger of Oscillation at High Frequencies with Inductive Loads Poor High Frequencies Attenuation Larger Bandwidth TDA2006 SHORT CIRCUIT PROTECTION The TDA2006 has an original circuit which limits the current of the output transistors. Figure 18 shows that the maximum output current is a function of the collector emitter voltage ; hence the output transistors work within their safe operating area (Figure 19). This function can therefore be considered as being peak power limiting rather than simple current limiting. It reduces the possibility that the device gets damaged during an accidental short circuit from AC output to ground. Figure 19 : Safe Operating Area and Collector Characteristics of the Protected Power Transistor THERMAL SHUT DOWN The presence of a thermal limiting circuit offers the following advantages : 1) an overload on the output (even if it is permanent), or an abo ve limit ambien t temperature can be easily supported since the Tj cannot be higher than 150°C. 2) the heatsink can have a smaller factor of safety compared with that of a conventional circuit. There is no possibility of device damage due to high junction temperature. If for any reason, the junction temperature increases up to 150 °C, the thermal shutdown simply reduces the power dissipation and the current consumption. Figure 20 : Output Power and Drain Current versus Case Temlperature (RL = 4Ω) The maximum allowable power dissipation depends upon the size of the external heatsink (i.e. its thermal resistance) ; Figure 22 shows the dissipable power as a function of ambient temperature for different thermal resistances. Figure 18 : Maximum Output Current versus Voltage VCE (sat) accross each Output Transistor Figure 21 : Output Power and Drain Current versus Case Temlperature (RL = 8Ω) 9/12 TDA2006 Figure 22 : Maximum Allowable Power Dissipation versus Ambient Temperature DIMENSION SUGGESTION The followingtable shows the length of the heatsink in Figure 23 for several values of Ptot and R th. Ptot (W) Lenght of Heatsink (mm) R th of Heatsink (°C/W) 12 60 4.2 Figure 23 : Example of Heatsink 10/12 8 40 6.2 6 30 8.3 TDA2006 PENTAWATT PACKAGE MECHANICAL DATA DIM. mm TYP. MIN. A C D D1 E F F1 G G1 H2 H3 L L1 L2 L3 L5 L6 L7 M M1 Dia MAX. 4.8 1.37 2.8 1.35 0.55 1.05 1.4 2.4 1.2 0.35 0.8 1 3.4 6.8 10.4 10.4 10.05 MIN. inch TYP. 0.094 0.047 0.014 0.031 0.039 0.126 0.260 0.134 0.268 MAX. 0.189 0.054 0.110 0.053 0.022 0.041 0.055 0.142 0.276 0.409 0.409 0.396 17.85 15.75 21.4 22.5 0.703 0.620 0.843 0.886 2.6 15.1 6 3 15.8 6.6 0.102 0.594 0.236 0.118 0.622 0.260 4.5 4 0.177 0.157 3.65 3.85 0.144 0.152 E L D1 C D M A M1 L1 L2 L5 G1 G H3 L3 L7 F H2 F1 Dia. L6 11/12 TDA2006 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. 1995 SGS-THOMSON Microelectronics - All Rights Reserved PENTAWATT is Registered Trademark of SGS-THOMSON Microelectronics SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thaliand - United Kingdom - U.S.A. 12/12