TI THS6002IDWP

THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
D
D
D
D
D
D
D
DWP PACKAGE
(TOP VIEW)
ADSL Differential Line Driver and Receiver
Driver Features
– 140 MHz Bandwidth (–3dB) With
25-Ω Load
– 315 MHz Bandwidth (–3dB) With
100-Ω Load
– 1000 V/µs Slew Rate, G = 2
– 400 mA Output Current Minimum Into
25-Ω Load
– –72 dB 3rd Order Harmonic Distortion at
f = 1 MHz, 25-Ω Load, and 20 VO(PP)
Receiver Features
– 330 MHz Bandwidth (–3dB)
– 900 V/µs Slew Rate at G = 2
– – 76 dB 3rd Order Harmonic Distortion at
f = 1 MHz, 150-Ω Load, and 20 VO(PP)
Wide Supply Range ± 4.5 V to ±16 V
Available in the PowerPAD Package
Improved Replacement for AD816 or
EL1501
Evaluation Module Available
VCC –
D1 OUT
VCC+
D1 IN+
D1 IN–
R1 IN–
R1 IN+
VCC+
R1 OUT
VCC –
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
VCC –
D2 OUT
VCC+
D2 IN+
D2 IN–
R2 IN–
R2 IN+
VCC+
R2 OUT
VCC –
Cross Section View Showing PowerPAD
description
The THS6002 contains two high-current, high-speed drivers and two high-speed receivers. These drivers and
receivers can be configured differentially for driving and receiving signals over low-impedance lines. The
THS6002 is ideally suited for asymmetrical digital subscriber line (ADSL) applications where it supports the
high-peak voltage and current requirements of that application. Both the drivers and the receivers are current
feedback amplifiers designed for the high slew rates necessary to support low total harmonic distortion (THD)
in ADSL applications. Separate power supply connections for each driver are provided to minimize crosstalk.
HIGH-SPEED xDSL LINE DRIVER/RECEIVER FAMILY
DEVICE
THS6002
THS6012
THS6022
THS6062
THS7002
DRIVER
RECEIVER
•
•
•
•
•
•
5V
•
±5 V
±15 V
•
•
•
•
•
•
•
•
•
•
BW
(MHz)
SR
(V/µs)
THD
f = 1 MHz
(dB)
IO
(mA)
Vn
(nV/√Hz)
140
1000
–62
500
1.7
140
1300
–65
500
1.7
210
1900
–66
250
1.7
100
100
–72
90
1.6
70
100
–84
25
2.0
CAUTION: The THS6002 provides ESD protection circuitry. However, permanent damage can still occur if this device is subjected
to high-energy electrostatic discharges. Proper ESD precautions are recommended to avoid any performance degradation or loss
of functionality.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments Incorporated.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
description (continued)
The THS6002 is packaged in the patented PowerPAD package. This package provides outstanding thermal
characteristics in a small footprint package, which is fully compatible with automated surface mount assembly
procedures. The exposed thermal pad on the underside of the package is in direct contact with the die. By simply
soldering the pad to the PWB copper and using other thermal outlets, the heat is conducted away from the
junction.
AVAILABLE OPTIONS
PACKAGED DEVICE
TA
PowerPAD PLASTIC
SMALL OUTLINE†
(DWP)
EVALUATION
MODULE
0°C to 70°C
THS6002CDWP
THS6002EVM
– 40°C to 85°C
THS6002IDWP
† The DWP packages are available taped and reeled. Add an R suffix to the
device type (i.e., THS6002CDWPR)
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage, VCC+ to VCC– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 V
Input voltage, VI (driver and receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VCC
Output current, IO (driver) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 mA
Output current, IO (receiver) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 mA
Differential input voltage, VID (driver and receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Continuous total power dissipation at (or below) TA = 25°C (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8 W
Operating free air temperature, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 125°C
Lead temperature, 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The THS6002 incorporates a PowerPad on the underside of the chip. This acts as a heatsink and must be connected to a thermal
dissipation plane for proper power dissipation. Failure to do so can result in exceeding the maximum junction temperature, which could
permanently damage the device. See the Thermal Information section of this document for more information about PowerPad
technology.
recommended operating conditions
MIN
Supply voltage
voltage, VCC+
CC and VCC –
Operating
O
erating free-air tem
temperature
erature, TA
2
Split supply
Single supply
C suffix
I suffix
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TYP
MAX
± 4.5
± 16
9
32
0
70
– 40
85
UNIT
V
°C
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
functional block diagram
Driver 1
3 V +
CC
D1 IN+
4
+
2
D1 IN–
5
1
Driver 2
D2 IN+
17
18
D2 IN–
8
VCC+
D2 OUT
_
20
VCC+
VCC–
+
19
16
D1 OUT
_
Receiver 1
+
7
VCC–
R1 IN+
R1 OUT 9
_
6
R1 IN–
VCC– 10
VCC+
13
Receiver 2
+
R2 OUT
14
R2 IN+
12
_
15 R2 IN–
VCC– 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
DRIVER
electrical characteristics, VCC = ±15 V, RL = 25 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
VCC
Split supply
Power supply operating range
Single supply
Single ended
VO
Common mode input voltage range
Common-mode
VCC = ± 5 V
VCC = ± 15 V
VIO
Input offset voltage
VCC = ± 5 V or ± 15 V
Input offset voltage drift
VCC = ± 5 V or ± 15 V,
Differential input offset voltage
VCC = ± 5 V or ± 15 V
Differential input offset voltage drift
VCC = ± 5 V or ± 15 V,
±16.5
9
33
3.2
to
–3
VCC = ± 15 V
11.8
to
–11.5
12.5
to
–12.2
VCC = ± 5 V
6
to
– 5.6
6.4
to
–6
VCC = ± 15 V
23.6
to
– 23
25
to
– 24.4
RL = 50 Ω
± 3.6
± 3.7
± 13.4
± 13.5
TA = 25°C
TA = full range
2
TA = full range
TA = 25°C
1.5
Input
In
ut bias current
Positive
VCC = ± 5 V or ± 15 V
TA = 25°C
4
TA = full range
VCC = ± 5 V,
VCC = ± 15 V,
Output current (see Note 2)
1.5
IOS
Short-circuit output current (see Note 2)
CMRR
500
400
1.5
VCC = ± 15 V
Common-mode rejection ratio
Differential common-mode rejection ratio
500
800
VCC = ± 5 V
Open
loop transresistance
O
en loo
VCC = ± 5 V or ± 15 V,
V
10
8
11
RL = 5 Ω
RL = 25 Ω
9
12
TA = full range
IO
4
12
TA = 25°C
Differential
5
10
TA = full range
IIB
V
5
3
V
V
20
TA = full range
TA = full range
UNIT
V
7
TA = 25°C
Negative
MAX
±4.5
3
to
– 2.8
RL = 25 Ω
VICR
TYP
VCC = ± 5 V
Output voltage swing
Differential
MIN
mV
µV/°C
mV
µV/°C
µA
µA
µA
mA
mA
MΩ
5
TA = full range
62
70
dB
100
Crosstalk
Driver to driver
VI = 200 mV,
f = 1 MHz
– 62
dB
† Full range is 0°C to 70°C for the THS6002C and – 40°C to 85°C for the THS6002I.
NOTE 2: A heat sink is required to keep the junction temperature below absolute maximum when an output is heavily loaded or shorted. See
absolute maximum ratings and Thermal Information section.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
DRIVER
electrical characteristics, VCC = ±15 V, RL = 25 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
(continued)
TEST CONDITIONS†
PARAMETER
VCC = ± 5 V
PSRR
Power su
supply
ly rejection ratio
VCC = ± 15 V
CI
Differential input capacitance
RI
Input resistance
RO
Output resistance
ICC
MIN
TYP
TA = 25°C
– 68
– 74
TA = full range
– 65
TA = 25°C
TA = full range
– 64
UNIT
dB
– 72
dB
– 62
Open loop
1.4
pF
300
kΩ
13
Ω
VCC = ± 5 V
TA = 25°C
TA = full range
8.5
VCC = ± 15 V
TA = 25°C
TA = full range
11.5
Quiescent current
MAX
10
12
13
mA
15
† Full range is 0°C to 70°C for the THS6002C and – 40°C to 85°C for the THS6002I.
operating characteristics, VCC = ±15 V, RL = 25 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
PARAMETER
SR
Differential slew rate
ts
Settling time to 0.1%
TEST CONDITIONS
VO = 20 V(PP),
0 V to 10 V Step,
MIN
1000
G=2
70
THD
Total harmonic distortion
VO(PP) = 20 V,RF = 4 kΩ,
G = 5,
Vn
Input voltage noise
VCC = ± 5 V or ± 15 V,
G = 2,
f = 10 kHz,
Single-ended
In
Input noise current
VCC = ± 5 V or ± 15 V,,
G=2
f = 10 kHz,,
VI = 200 mV,,
RF = 680 Ω
G = 1,,
VCC = ± 5 V
VCC = ± 15 V
VI = 200 mV,
RF = 620 Ω
G = 2,
VI = 200 mV,
RF = 820 Ω,
Positive (IN+)
Negative (IN–)
UNIT
V/µs
ns
– 62
dBc
1.7
nV/√Hz
11.5
16
pA/√Hz
90
110
MHz
140
MHz
VCC = ± 15 V
120
MHz
G = 1,
RL = 100 Ω
VCC = ± 15 V
315
MHz
VI = 200 mV,
RF = 560 Ω,
G = 2,
RL = 100 Ω
VCC = ± 15 V
265
MHz
Bandwidth for 0.1
0 1 dB flatness
VI = 200 mV,,
RF = 680 Ω
G = 1,,
VCC = ± 5 V
VCC = ± 15 V
30
Full power bandwidth (see Note 3)
VO = 20 V(PP)
Differential gain error
G = 2,,
RL = 150 Ω,
BW
φD
f = 1 MHz
MAX
110
Small-signal bandwidth (–3 dB)
AD
TYP
G=2
G = 2,
RL = 150 Ω,
Differential phase error
40
16
NTSC,,
40 IRE
NTSC,
40 IRE
VCC = ± 5 V
VCC = ± 15 V
0.04%
VCC = ± 5 V
0.07°
VCC = ± 15 V
0.08°
MHz
MHz
0.05%
NOTE 3: Full power bandwidth = slew rate/2πVpeak
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
RECEIVER
electrical characteristics, VCC = ±15 V, RL = 150 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
Power supply operating range
VO
Output voltage swing
VICR
Common mode input voltage range
Common-mode
Single ended
± 16.5
9
33
VCC = ± 5 V
VCC = ± 15 V
±3
± 3.3
± 12.4
± 12.8
VCC = ± 5 V
VCC = ± 15 V
± 3.6
± 3.7
± 13.4
± 13.5
VCC = ± 5 V or ± 15 V
Input offset voltage
Differential
Input offset voltage drift
Single ended
Differential
Negative
IIB
Input
In
ut bias current
Positive
Differential
TA = 25°C
TA = full range
1
TA = 25°C
TA = full range
1.5
VCC = ± 5 V or ± 15 V
VCC = ± 5 V or ± 15 V
TA = 25°C
2
TA = full range
3.5
TA = full range
TA = 25°C
1.5
TA = full range
RL = 25 Ω
110
VCC = ±5 V
1.5
Crosstalk (receiver to receiver)
PSRR
RL = 25 Ω
95
80
VCC = ± 15 V
µA
8
85
mA
mA
MΩ
5
60
VCC = ± 5 V or ± 15 V,
V
TA = full range
VI = 200 mV,
f = 1 MHz
VCC = ± 5 V
TA = 25°C
TA = full range
– 66
VCC = ± 15 V
TA = 25°C
TA = full range
– 65
Power supply rejection ratio
9
10
Short-circuit output current (see Note 2)
Differential
µV/°C
8
11
IOS
Single ended
mV
10
TA = 25°C
VCC = ± 5 V
VCC = ± 15 V
Common-mode rejection ratio
4
5
Output current (see Note 2)
CMRR
4
10
RL = 150 Ω
V
V
20
VCC = ± 5 V or ± 15 V
VCC = ± 5 V or ± 15 ,
UNIT
V
6
IO
Open
O
en loo
loop transresistance
MAX
± 4.5
Single ended
VIO
TYP
Single supply
Split supply
VCC
MIN
70
dB
100
– 67
dB
– 74
– 63
– 72
dB
– 62
RI
Input resistance
300
kΩ
CI
Differential input capacitance
1.4
pF
RO
Output resistance
Open loop
10
Ω
† Full range is 0°C to 70°C for the THS6002C and – 40°C to 85°C for the THS6002I.
NOTE 2: A heat sink is required to keep junction temperature below absolute maximum when an output is heavily loaded or shorted. See absolute
maximum ratings and Thermal Information section.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
RECEIVER
electrical characteristics, VCC = ±15 V, RL = 150 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
(continued)
TEST CONDITIONS†
PARAMETER
ICC
TYP
MAX
VCC = ± 5 V
TA = 25°C
TA = full range
4.2
5.5
VCC = ± 15 V
TA = 25°C
TA = full range
5
Quiescent current
MIN
7.5
7
UNIT
mA
9
† Full range is 0°C to 70°C for the THS6002C and – 40°C to 85°C for the THS6002I.
operating characteristics, VCC = ±15 V, RL = 150 Ω, RF = 1 kΩ, TA = 25°C (unless otherwise noted)
PARAMETER
SR
Differential slew rate
ts
Settling time to 0.1%
TEST CONDITIONS
MIN
TYP
900
V/µs
G=2
50
ns
RF = 510 Ω,
f =1 MHz
THD
Total harmonic distortion
Vn
Input voltage noise
VCC = ± 5 V or ± 15 V
G=2
f = 10 kHz,
In
Input current noise
VCC = ± 5 V or ± 15 V,,
G=2
f = 10 kHz,,
VI = 200 mV,,
RF = 560 Ω
G = 1,,
VCC = ± 5 V
VCC = ± 15 V
VI = 200 mV,
RF = 430 Ω
G = 2,
Bandwidth for 0.1
0 1 dB flatness
VI = 200 mV,,
RF = 560 Ω
G = 1,,
Full power bandwidth (see Note 3)
VO = 20 V(PP)
AD
Differential gain error
40 IRE,,
RL = 150 Ω,
G = 2,,
NTSC
VCC = ± 5 V
VCC = ± 15 V
0.09%
φD
Differential phase error
40 IRE,,
RL = 150 Ω,
G = 2,,
NTSC
VCC = ± 5 V
VCC = ± 15 V
0.13°
Negative (IN–)
Small-signal bandwidth (–3 dB)
BW
UNIT
G=2
VO(PP) = 20 V,
G = 5,
Positive (IN+)
MAX
VO = 10 V(PP),
10 V Step,
– 68
dBc
1.7
nV/√Hz
11.5
16
270
300
300
330
VCC = ± 15 V
285
VCC = ± 5 V
VCC = ± 15 V
20
25
14
pA/√Hz
MHz
MHz
MHz
MHz
0.1%
0.16°
NOTE 3: Full power bandwidth = slew rate/2πVpeak
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
PARAMETER MEASUREMENT INFORMATION
1 kΩ
1 kΩ
1 kΩ
–
Driver 1
–
VO
+
VI
1 kΩ
VO
25 Ω
50 Ω
Driver 2
+
25 Ω
VI
50 Ω
Figure 1. Driver Input-to-Output Crosstalk Test Circuit
1 kΩ
1 kΩ
Receiver 1
VI
1 kΩ
–
–
VO
+
VO
150 Ω
50 Ω
+
150 Ω
1 kΩ
Receiver 2
VI
50 Ω
Figure 2. Receiver Input-to-Output Crosstalk Test Circuit
RG
RF
15 V
Driver
VI
50 Ω
–
VO
+
–15 V
RL
25 Ω
Figure 3. Driver Test Circuit, Gain = 1 + (RF/RG)
RG
RF
15 V
VI
Receiver
50 Ω
–
VO
+
–15 V
RL
150 Ω
Figure 4. Receiver Test Circuit, Gain = 1 + (RF/RG)
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Supply current
Driver and Receiver
vs Supply voltage
5
Input voltage noise
Driver and Receiver
vs Frequency
6
Input current noise
Driver and Receiver
vs Frequency
6
Closed-loop output impedance
Driver and Receiver
vs Frequency
7
Driver
vs Supply voltage
8
Receiver
vs Supply voltage
31
Driver
vs Load resistance
9
Receiver
vs Load resistance
32
Driver
vs Free-air temperature
10
Receiver
vs Free-air temperature
33
Driver
vs Free-air temperature
11
Receiver
vs Free-air temperature
34
Driver
vs Free-air temperature
12
Receiver
vs Free-air temperature
35
Driver
vs Frequency
13
Receiver
vs Frequency
36
Driver-to-receiver crosstalk
vs Frequency
14
Receiver-to-driver crosstalk
vs Frequency
37
Driver
vs Free-air temperature
15
Receiver
vs Free-air temperature
38
Driver
vs Free-air temperature
16
Receiver
vs Free-air temperature
Driver
vs Frequency
17, 18
Receiver
vs Frequency
40, 41
Normalized output response
Driver
vs Frequency
19 – 22
Single-ended output distortion
Driver
vs Output voltage
Output distortion
Receiver
vs Output voltage
Small and large signal frequency response
Receiver
Peak to peak output voltage swing
Peak-to-peak
Peak to peak output voltage
Peak-to-peak
VIO
Input offset voltage
IIB
Input bias current
CMMR
Common mode rejection ratio
Common-mode
Input to output crosstalk
Input-to-output
PSSR
ICC
Power supply rejection ratio
Supply current
Normalized frequency response
Driver
Differential gain
Receiver
Driver
Differential phase
Receiver
Output step response
39
23
42
43, 44
DC input offset voltage
24, 25
Number of 150-Ω loads
26, 27
DC input offset voltage
45, 46
Number of 150-Ω loads
47, 48
DC input offset voltage
24, 25
Number of 150-Ω loads
26, 27
DC input offset voltage
45, 46
Number of 150-Ω loads
47, 48
Driver
28 – 30
Receiver
49 – 51
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
DRIVER AND RECEIVER
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
INPUT VOLTAGE AND CURRENT NOISE
vs
FREQUENCY
12
100
VCC = ±15 V
TA = 25°C
11
I CC – Supply Current – mA
Vn – Voltage Noise – nV/ Hz
Driver
10
9
8
7
6
5
Receiver
4
3
1
0
In– Noise
10
In+ Noise
TA = 25°C
RF = 1 kΩ
Gain = +1
2
5
6
7
10
Vn Noise
8
9
10
11
12
13
14
1
10
15
± VCC – Supply Voltage – V
100
1k
f – Frequency – Hz
Figure 5
Figure 6
DRIVER AND RECEIVER
CLOSED-LOOP OUTPUT IMPEDANCE
vs
FREQUENCY
Closed-Loop Output Impedance – Ω
200
100
10
VCC = ±15 V
RF = 1 kΩ
Gain = 2
TA = 25°C
VI(PP) = 1 V
Receiver
1
Driver
0.1
1 kΩ
–
+
0.01
VO
1 kΩ
1 kΩ
50 Ω
VI
THS6002
1000
VI
Zo =
–1
VO
(
0.001
100k
1M
10M
f – Frequency – Hz
100M
Figure 7
10
100
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
)
500M
10k
1
100k
I n – Current Noise – pA/ Hz
DRIVER AND RECEIVER
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
DRIVER
DRIVER
PEAK-TO-PEAK OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
PEAK-TO-PEAK OUTPUT VOLTAGE
vs
LOAD RESISTANCE
15
15
VO(PP) – Peak-to-Peak Output Voltage – V
VO(PP) – Peak-to-Peak Output Voltage Swing – V
TYPICAL CHARACTERISTICS
10
5
0
–5
TA = 25°C
RF = 1 kΩ
RL = 25 Ω
Gain = 1
–10
–15
5
6
7
8
9
10
11
12
13
14
VCC = ±15 V
10
VCC = ±5 V
5
TA = 25°C
RF = 1 kΩ
Gain = 1
0
VCC = ±5 V
–5
–10
VCC = ±15 V
–15
10
15
100
Figure 8
Figure 9
DRIVER
DRIVER
INPUT OFFSET VOLTAGE
vs
FREE-AIR TEMPERATURE
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
2
5
VCC = ±15 V
IIB+
G=1
RF = 1 kΩ
G=1
RF = 1 kΩ
See Figure 2
4
I IB – Input Bias Current – µ A
VIO – Input Offset Voltage – mV
1
1000
RL – Load Resistance – Ω
VCC – Supply Voltage – V
VCC = ±5 V
0
–1
–2
VCC = ±15 V
–3
VCC = ±5 V
IIB+
3
2
VCC = ±5 V
IIB–
1
–4
–5
–40
–20
0
20
40
60
80
100
0
–40
–20
TA – Free-Air Temperature – °C
0
20
VCC = ±15 V
IIB–
40
60
80
100
TA – Free-Air Temperature – °C
Figure 10
Figure 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
DRIVER
DRIVER
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
INPUT-TO-OUTPUT CROSSTALK
vs
FREQUENCY
0
80
–10
Input-to-Output Crosstalk – dB
CMRR – Common-Mode Rejection Ratio – dB
TYPICAL CHARACTERISTICS
75
VCC = ±15 V
70
VCC = ±5 V
1 kΩ
65
1 kΩ
–
+
VI
1 kΩ
60
–40
–20
VO
–30
–40
Driver 1 = Output
Driver 2 = Input
–50
–60
–70
Driver 1 = Input
Driver 2 = Output
–80
1 kΩ
0
–20
VCC = ±15 V
RF = 1 kΩ
RL = 25 Ω
Gain = 2
VI = 200 mV
See Figure 1
20
40
60
–90
100k
80
1M
TA – Free-Air Temperature – °C
Figure 12
10M
f – Frequency – Hz
100M
500M
Figure 13
DRIVER
DRIVER-TO-RECEIVER CROSSTALK
vs
FREQUENCY
Driver-to-Receiver Crosstalk – dB
–10
–20
95
VCC = ±15 V
RF = 1 kΩ
Gain = 2
VI = 200 mV
See Figures 1 and 2
PSRR – Power Supply Rejection Ratio – dB
0
POWER SUPPLY REJECTION RATIO
vs
FREE-AIR TEMPERATURE
–30
–40
Receiver 2 = Output
Driver 2 = Input
Receiver 1 = Output
Driver 1 = Input
–50
–60
Receiver 1 = Output
Driver 2 = Input
–70
–80
–90
100k
Receiver 2 = Output
Driver 1 = Input
1M
10M
f – Frequency – Hz
100M
500M
G=1
RF = 1 kΩ
90
85
VCC = 15 V
80
VCC = 5 V
75
VCC = –5 V
VCC = –15 V
70
65
–40
–20
20
Figure 15
POST OFFICE BOX 655303
40
60
TA – Free-Air Temperature – °C
Figure 14
12
0
• DALLAS, TEXAS 75265
80
100
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
DRIVER
DRIVER
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
NORMALIZED FREQUENCY RESPONSE
vs
FREQUENCY
2
13
Normalized Frequency Response – dB
VCC = ±15 V
I CC – Supply Current – mA
12
VCC = ±5 V
10
8
6
4
2
0
–1
–20
0
20
40
60
80
RF = 750 Ω
–3
RF = 1 kΩ
–4
–5
–6
–8
100
100
RF = 510 Ω
–2
–7
0
–40
RF = 300 Ω
1
VCC = ±15 V
VI = 200 mV
RL = 25 Ω
Gain = 1
TA = 25°C
1M
Figure 16
DRIVER
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
RL = 200 Ω
0
Normalized Output Response – dB
Normalized Frequency Response – dB
1
RF = 360 Ω
0
–1
–2
–3
RF = 470 Ω
–4
–5
–6
–9
500M
Figure 17
DRIVER
1
–8
100M
NORMALIZED FREQUENCY RESPONSE
vs
FREQUENCY
2
–7
10M
f – Frequency – Hz
TA – Free-Air Temperature – °C
VCC = ±15 V
Vin = 200 mV
RL = 25 Ω
Gain = 2
TA = 25°C
–10
100K
1M
RF = 620 Ω
–2
100M
500M
RL = 100 Ω
–3
RL = 50 Ω
–4
RL = 25 Ω
–5
–6
–7
–8
RF = 1 kΩ
10M
–1
VCC = ±15 V
RF = 1 kΩ
Gain = 1
VI = 200 mV
–9
100k
f – Frequency – Hz
Figure 18
1M
10M
f – Frequency – Hz
100M
500M
Figure 19
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
DRIVER
DRIVER
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
1
3
0
2
Normalized Output Response – dB
Normalized Output Response – dB
TYPICAL CHARACTERISTICS
–1
–2
–3
–4
RL = 25 Ω
–5
RL = 200 Ω
RL = 100 Ω
–6
–7
–8
RL = 50 Ω
VCC = ±15 V
RF = 1 kΩ
Gain = 2
VI = 200 mV
–9
100k
RF = 620 Ω
RF = 820 Ω
1
0
–1
RF = 1 kΩ
–2
–3
–4
VCC = ±15 V
RL = 100 Ω
Gain = 1
VI = 200 mV
–5
–6
1M
10M
f – Frequency – Hz
100M
–7
100k
500M
1M
Figure 20
DRIVER
DRIVER
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
SINGLE-ENDED OUTPUT DISTORTION
vs
OUTPUT VOLTAGE
0
RF = 430 Ω
1
0
–1
–2
RF = 620 Ω
–3
RF = 1 kΩ
VCC = ±15 V
RL = 100 Ω
Gain = 2
VI = 200 mV
–6
100k
–20
–30
–40
–50
2nd Harmonic
–60
–70
3rd Harmonic
–80
–90
1M
10M
f – Frequency – Hz
100M
500M
0
Figure 22
14
500M
VCC = ±15 V
RF = 4 kΩ
RL = 25 Ω
f = 1 MHz
Gain = 5
–10
Single-Ended Output Distortion – dB
Normalized Output Response – dB
2
–5
100M
Figure 21
3
–4
10M
f – Frequency – Hz
5
10
15
VO(PP) – Output Voltage – V
Figure 23
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
20
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
DRIVER
DIFFERENTIAL GAIN AND PHASE
vs
DC INPUT OFFSET VOLTAGE
Differential Gain – %
0.04
0.10
VCC = ±15 V
RL = 150 Ω
RF = 1 kΩ
f = 3.58 MHz
Gain = 2
40 IRE Modulation
Gain
0.08
Phase
0.03
0.06
0.02
0.04
0.01
0.02
0
–0.7
–0.5
–0.3
–0.1
0.1
0.3
0.5
Differential Phase – °
0.05
0
0.7
DC Input Offset Voltage – V
Figure 24
DRIVER
DIFFERENTIAL GAIN AND PHASE
vs
DC INPUT OFFSET VOLTAGE
Differential Gain – %
0.04
0.10
VCC = ±5 V
RL = 150 Ω
RF = 1 kΩ
f = 3.58 MHz
Gain = 2
40 IRE Modulation
0.08
0.03
0.06
Gain
0.04
0.02
Differential Phase – °
0.05
Phase
0.02
0.01
0
–0.7
–0.5
–0.3
–0.1
0.1
0.3
0.5
0
0.7
DC Input Offset Voltage – V
Figure 25
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
DRIVER
DIFFERENTIAL GAIN AND PHASE
vs
NUMBER OF 150-Ω LOADS
0.12
Differential Gain – %
0.25
VCC = ±15 V
RF = 1 kΩ
Gain = 2
f = 3.58 MHz
40 IRE Modulation
100 IRE Ramp
0.20
0.09
0.15
Phase
0.10
0.06
Differential Phase – °
0.15
Gain
0.05
0.03
0
0
1
2
3
4
5
6
7
8
Number of 150-Ω Loads
Figure 26
DRIVER
DIFFERENTIAL GAIN AND PHASE
vs
NUMBER OF 150-Ω LOADS
0.12
Differential Gain – %
0.25
VCC = ±5 V
RF = 1 kΩ
Gain = 2
f = 3.58 MHz
40 IRE Modulation
100 IRE Ramp
0.20
0.09
0.15
0.10
0.06
Gain
0.05
0.03
Phase
0
0
1
2
3
4
5
6
7
Number of 150-Ω Loads
Figure 27
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
8
Differential Phase – °
0.15
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
DRIVER OUTPUT
10 V STEP RESPONSE
8
300
6
200
4
VO – Output Voltage – V
400
100
0
–100
VCC = ±15 V
Gain = 2
RL = 25 Ω
RF = 1 kΩ
tr/tf= 300 ps
See Figure 3
–200
–300
2
0
–2
VCC = ±15 V
Gain = 2
RL = 25 Ω
RF = 1 kΩ
tr/tf= 5 ns
See Figure 3
–4
–6
–8
–400
0
50
0
100 150 200 250 300 350 400 450 500
50
100 150 200 250 300 350 400 450 500
t – Time – ns
t – Time – ns
Figure 28
Figure 29
DRIVER OUTPUT
20 V STEP RESPONSE
16
VCC = ±15 V
Gain = 5
RL = 25 Ω
RF = 2 kΩ
tr/tf= 5 ns
See Figure 3
12
VO – Output Voltage – V
VO – Output Voltage – mV
DRIVER OUTPUT
400 mV STEP RESPONSE
8
4
0
–4
–8
–12
–16
0
50
100 150 200 250 300 350 400 450 500
t – Time – ns
Figure 30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER
RECEIVER
PEAK-TO-PEAK OUTPUT VOLTAGE SWING
vs
SUPPLY VOLTAGE
PEAK-TO-PEAK OUTPUT VOLTAGE
vs
LOAD RESISTANCE
15
VO(PP) – Peak-to-Peak Output Voltage – V
VO(PP) – Peak-to-Peak Output Voltage Swing – V
15
10
5
0
–5
TA = 25°C
RF = 1 kΩ
RL = 150 Ω
Gain = 1
–10
–15
5
6
7
8
9
10
11
12
13
14
10
TA = 25°C
RF = 1 kΩ
Gain = 1
VCC = ±15 V
VCC = ±5 V
5
0
VCC = ±5 V
–5
–10
VCC = ±15 V
–15
10
15
100
Figure 31
Figure 32
RECEIVER
RECEIVER
INPUT OFFSET VOLTAGE
vs
FREE-AIR TEMPERATURE
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
0.5
5
G=1
RF = 1 kΩ
0
4
I IB – Input Bias Current – µ A
VIO – Input Offset Voltage – mV
G=1
RF = 1 kΩ
VCC = ±5 V
–0.5
–1
VCC = ±15 V
–1.5
–2
–40
–20
0
20
40
60
80
100
VCC = ±15 V
IIB+
3
VCC = ±5 V
IIB+
2
1
0
–40
VCC = ±15 V
IIB–
VCC = ±5 V
IIB–
–20
TA – Free-Air Temperature – °C
0
20
Figure 34
POST OFFICE BOX 655303
40
60
TA – Free-Air Temperature – °C
Figure 33
18
1000
RL – Load Resistance – Ω
VCC – Supply Voltage – V
• DALLAS, TEXAS 75265
80
100
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
RECEIVER
RECEIVER
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
INPUT-TO-OUTPUT CROSSTALK
vs
FREQUENCY
85
0
–10
80
Input-to-Output Crosstalk – dB
CMRR – Common-Mode Rejection Ratio – dB
TYPICAL CHARACTERISTICS
VCC = ±15 V
75
70
VCC = ±5 V
65
1 kΩ
1 kΩ
–
+
VI
60
1 kΩ
55
–40
–20
VO
1 kΩ
0
–20
–30
VCC = ±15 V
RF = 1 kΩ
RL = 150 Ω
Gain = 2
VI = 200 mV
See Figure 2
Receiver 1 = Output
Receiver 2 = Input
–40
–50
–60
–70
Receiver 1 = Input
Receiver 2 = Output
–80
20
40
60
80
–90
100k
100
1M
TA – Free-Air Temperature – °C
Figure 35
10M
f – Frequency – Hz
100M
500M
Figure 36
RECEIVER
POWER SUPPLY REJECTION RATIO
vs
FREE-AIR TEMPERATURE
RECEIVER-TO-DRIVER CROSSTALK
vs
FREQUENCY
Receiver-to-Driver Crosstalk – dB
–10
95
VCC = ±15 V
RF = 1 kΩ
Gain = 2
PSRR – Power Supply Rejection Ratio – dB
0
–20
–30
Receiver 2 = Input
Driver 2 = Output
–40
Receiver 1 = Input
Driver 1 = Output
–50
–60
Receiver 1 = Input
Driver 2 = Output
–70
–80
–90
100k
Receiver 2 = Input
Driver 1 = Output
1M
10M
f – Frequency – Hz
100M
500M
G=1
RF = 1 kΩ
90
85
VCC = 15 V
80
VCC = 5 V
VCC = –15 V
75
VCC = –5 V
70
65
–40
–20
0
20
40
60
80
100
TA – Free-Air Temperature – °C
Figure 37
Figure 38
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER
RECEIVER
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
7
3
Normalized Output Response – dB
6
I CC – Supply Current – mA
VCC = ±15 V
RL = 150 Ω
Gain = 1
VI = 200 mV
2
VCC = ±15 V
5
4
VCC = ±5 V
3
2
1
1
RF = 360 Ω
0
–1
RF = 510 Ω
–2
–3
RF = 750 Ω
–4
RF = 1 kΩ
–5
–6
0
–40
–20
0
20
40
60
80
–7
100k
100
1M
TA – Free-Air Temperature – °C
RECEIVER
RECEIVER
NORMALIZED OUTPUT RESPONSE
vs
FREQUENCY
OUTPUT DISTORTION
vs
OUTPUT VOLTAGE
1
0
0
–10
–1
–20
–2
RF = 360 Ω
–3
RF = 510 Ω
–4
RF = 620 Ω
–5
RF = 1 kΩ
–6
–7
–8
VCC = ±15 V
RL = 150 Ω
Gain = 2
VI = 200 mV
–9
100k
500M
VCC = ±15 V
RF = 510 Ω
RL = 150 Ω
f = 1 MHz
Gain = 5
–30
–40
–50
–60
2nd Harmonic
–70
–80
3rd Harmonic
–90
–100
1M
10M
f – Frequency – Hz
100M
500M
0
Figure 41
20
100M
Figure 40
Output Distortion – dB
Normalized Output Response – dB
Figure 39
10M
f – Frequency – Hz
5
10
15
VO(PP) – Output Voltage – V
Figure 42
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
20
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER
RECEIVER
SMALL AND LARGE SIGNAL
FREQUENCY RESPONSE
SMALL AND LARGE SIGNAL
FREQUENCY RESPONSE
–3
3
VI = 500 mV
VI = 500 mV
–6
0
–3
Output Level – dBV
VI = 250 mV
–12
–15
VI = 125 mV
–18
–21
VI = 250 mV
–6
–9
VI = 125 mV
–12
–15
VI = 62.5 mV
–27
–18
VCC = ±15 V
RF = 510 Ω
RL = 150 Ω
Gain = 1
–30
100k
1M
–21
10M
f – Frequency – Hz
100M
VI = 62.5 mV
VCC = ±15 V
RF = 390 Ω
RL = 150 Ω
Gain = 2
–24
100k
500M
1M
Figure 43
10M
f – Frequency – Hz
100M
500M
Figure 44
RECEIVER
DIFFERENTIAL GAIN AND PHASE
vs
DC INPUT OFFSET VOLTAGE
0.10
0.20
VCC = ±15 V
RL = 150 Ω
RF = 1 kΩ
f = 3.58 MHz
Gain = 2
40 IRE Modulation
0.09
0.08
0.07
Gain
0.18
0.16
0.14
Phase
0.06
0.12
0.05
0.10
0.04
0.08
0.03
0.06
0.02
0.04
0.01
0.02
0
–0.7
–0.5
–0.3
–0.1
0.1
0.3
0.5
Differential Phase – °
–24
Differential Gain – %
Output Level – dBV
–9
0
0.7
DC Input Offset Voltage – V
Figure 45
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER
DIFFERENTIAL GAIN AND PHASE
vs
DC INPUT OFFSET VOLTAGE
0.09
0.08
Differential Gain – %
0.20
VCC = ±5 V
RL = 150 Ω
RF = 1 kΩ
f = 3.58 MHz
Gain = 2
40 IRE Modulation
0.07
0.18
0.16
0.14
0.06
0.12
Gain
0.05
0.10
0.04
0.08
0.03
0.06
0.02
0.04
Differential Phase – °
0.10
0.02
0.01
Phase
0
–0.7
–0.5
–0.3
–0.1
0.1
0.3
0.5
0
0.7
DC Input Offset Voltage – V
Figure 46
RECEIVER
DIFFERENTIAL GAIN AND PHASE
vs
NUMBER OF 150-Ω LOADS
0.40
0.35
Differential Gain – %
0.25
VCC = ±15 V
RF = 1 kΩ
Gain = 2
f = 3.58 MHz
40 IRE Modulation
100 IRE Ramp
0.30
0.20
0.15
Gain
0.25
Phase
0.20
0.10
0.15
0.10
0.05
0.05
0
0
1
2
3
4
5
6
7
Number of 150-Ω Loads
Figure 47
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
8
Differential Phase – °
0.45
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER
DIFFERENTIAL GAIN AND PHASE
vs
NUMBER OF 150-Ω LOADS
0.40
0.35
Differential Gain – %
0.25
VCC = ±5 V
RF = 1 kΩ
Gain = 2
f = 3.58 MHz
40 IRE Modulation
100 IRE Ramp
0.30
0.20
0.15
0.25
Phase
0.20
0.10
0.15
Differential Phase – °
0.45
Gain
0.10
0.05
0.05
0
0
1
2
3
4
5
6
7
8
Number of 150-Ω Loads
Figure 48
RECEIVER OUTPUT
10-V STEP RESPONSE
400
9
300
7
200
5
VO – Output Voltage – V
VO – Output Voltage – mV
RECEIVER OUTPUT
400-mV STEP RESPONSE
100
0
–100
Gain = +2
RL = 150 Ω
RF = 1 kΩ
tr/tf= 300 ps
See Figure 4
–200
–300
3
1
–1
Gain = +2
RL = 150 Ω
RF = 1 kΩ
tr/tf= 5 ns
See Figure 4
–3
–5
–7
–400
0
50
100 150 200 250 300 350 400 450 500
0
50
100 150 200 250 300 350 400 450 500
t – Time – ns
t – Time – ns
Figure 50
Figure 49
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
TYPICAL CHARACTERISTICS
RECEIVER OUTPUT
20 V STEP RESPONSE
16
VCC = ±15 V
Gain = 5
RL = 150 Ω
RF = 2 kΩ
tr/tf= 5 ns
See Figure 4
VO – Output Voltage – V
12
8
4
0
–4
–8
–12
–16
0
50
100 150 200 250 300 350 400 450 500
t – Time – ns
Figure 51
APPLICATION INFORMATION
The THS6002 contains four independent operational amplifiers. Two are designated as drivers because of their
high output current capability, and two are designated as receivers. The receiver amplifiers are current feedback
topology amplifiers made for high-speed operation and are capable of driving output loads of at least 80 mA.
The drivers are also current feedback topology amplifiers. However, the drivers have been specifically designed
to deliver the full power requirements of ADSL and therefore can deliver output currents of at least 400 mA at
full output voltage.
The THS6002 is fabricated using Texas Instruments 30-V complementary bipolar process, HVBiCOM. This
process provides excellent isolation and high slew rates that result in the device’s excellent crosstalk and
extremely low distortion.
independent power supplies
Each amplifier of the THS6002 has its own power supply pins. This was specifically done to solve a problem
that often occurs when multiple devices in the same package share common power pins. This problem is
crosstalk between the individual devices caused by currents flowing in common connections. Whenever the
current required by one device flows through a common connection shared with another device, this current,
in conjunction with the impedance in the shared line, produces an unwanted voltage on the power supply. Proper
power supply decoupling and good device power supply rejection helps to reduce this unwanted signal. What
is left is crosstalk.
However, with independent power supply pins for each device, the effects of crosstalk through common
impedance in the power supplies is more easily managed. This is because it is much easier to achieve low
common impedance on the PCB with copper etch than it is to achieve low impedance within the package with
either bond wires or metal traces on silicon.
24
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
power supply restrictions
Although the THS6002 is specified for operation from power supplies of ± 5 V to ±15 V (or singled-ended power
supply operation from 10 V to 30 V), and each amplifier has its own power supply pins, several precautions must
be taken to assure proper operation.
1. The power supplies for each amplifier must be the same value. For example, if the drivers use ±15 volts,
then the receivers must also use ±15 volts. Using ±15 volts for one amplifier and ±5 volts for another
amplifier is not allowed.
2. To save power by powering down some of the amplifiers in the package, the following rules must be
followed.
•
•
•
The amplifier designated Receiver 1 must always receive power whenever any other amplifier(s) within
the package is used. This is because the internal startup circuitry uses the power from the Receiver 1
device.
The –VCC pins from all four devices must always be at the same potential.
Individual amplifiers are powered down by simply opening the +VCC connection.
As an example, if only the two drivers within the THS6002 are used, then the package power is reduced by
removing the +VCC connection to Receiver 2. This reduces the power consumption by an amount equal to the
quiescent power of a single receiver amplifier. The +VCC connections to Receiver 1 and both drivers are
required. Also, all four amplifiers must be connected to –VCC, including Receiver 2.
The THS6002 incorporates a standard Class A-B output stage. This means that some of the quiescent current
is directed to the load as the load current increases. So under heavy load conditions, accurate power dissipation
calculations are best achieved through actual measurements. For small loads, however, internal power
dissipation for each amplifier in the THS6002 can be approximated by the following formula:
P
D
Where:
PD
VCC
ICC
VO
RL
ǒ
≅ 2 V
I
CC CC
Ǔ)ǒ
V
CC
_ V
Ǔ
O
ǒǓ
V
O
R
L
= power dissipation for one amplifier
= split supply voltage
= supply current for that particular amplifier
= output voltage of amplifier
= load resistance
To find the total THS6002 power dissipation, we simply sum up all four amplifier power dissipation results.
Generally, the worst case power dissipation occurs when the output voltage is one-half the VCC voltage. One
last note, which is often overlooked: the feedback resistor (RF) is also a load to the output of the amplifier and
should be taken into account for low value feedback resistors.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
device protection features
The THS6002 has two built-in protection features that protect the device against improper operation. The first
protection mechanism is output current limiting. Should the output become shorted to ground the output current
is automatically limited to the value given in the data sheet. While this protects the output against excessive
current, the device internal power dissipation increases due to the high current and large voltage drop across
the output transistors. Continuous output shorts are not recommended and could damage the device.
Additionally, connection of the amplifier output to one of the supply rails (±VCC) can cause failure of the device
and is not recommended.
The second built-in protection feature is thermal shutdown. Should the internal junction temperature rise above
approximately 180_C, the device automatically shuts down. Such a condition could exist with improper heat
sinking or if the output is shorted to ground. When the abnormal condition is fixed, the internal thermal shutdown
circuit automatically turns the device back on.
thermal information
The THS6002 is packaged in a thermally-enhanced DWP package, which is a member of the PowerPAD family
of packages. This package is constructed using a downset leadframe upon which the die is mounted
[see Figure 52(a) and Figure 52(b)]. This arrangement results in the lead frame being exposed as a thermal pad
on the underside of the package [see Figure 52(c)]. Because this thermal pad has direct thermal contact with
the die, excellent thermal performance can be achieved by providing a good thermal path away from the thermal
pad.
The PowerPAD package allows for both assembly and thermal management in one manufacturing operation.
During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be
soldered to a copper area underneath the package. Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either a ground plane or other heat dissipating device. This
is discussed in more detail in the PCB design considerations section of this document.
The PowerPAD package represents a breakthrough in combining the small area and ease of assembly of
surface mount with the, heretofore, awkward mechanical methods of heatsinking.
DIE
Side View (a)
Thermal
Pad
DIE
End View (b)
Bottom View (c)
NOTE A: The thermal pad is electrically isolated from all terminals in the package.
Figure 52. Views of Thermally Enhanced DWP Package
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
recommended feedback and gain resistor values
As with all current feedback amplifiers, the bandwidth of the THS6002 is an inversely proportional function of
the value of the feedback resistor. This can be seen from Figures 17 and 18. For the driver, the recommended
resistors for the optimum frequency response for a 25-Ω load system are 680-Ω for a gain = 1 and 620-Ω for
a gain = 2 or –1. For the receivers, the recommended resistors for the optimum frequency response are
560 Ω for a gain = 1 and 390 Ω for a gain = 2 or –1. These should be used as a starting point and once optimum
values are found, 1% tolerance resistors should be used to maintain frequency response characteristics.
Because there is a finite amount of output resistance of the operational amplifier, load resistance can play a
major part in frequency response. This is especially true with the drivers, which tend to drive low-impedance
loads. This can be seen in Figure 7, Figure 19, and Figure 20. As the load resistance increases, the output
resistance of the amplifier becomes less dominant at high frequencies. To compensate for this, the feedback
resistor should change. For 100-Ω loads, it is recommended that the feedback resistor be changed to 820 Ω
for a gain of 1 and 560 Ω for a gain of 2 or –1. Although, for most applications, a feedback resistor value of
1 kΩ is recommended, which is a good compromise between bandwidth and phase margin that yields a very
stable amplifier.
Consistent with current feedback amplifiers, increasing the gain is best accomplished by changing the gain
resistor, not the feedback resistor. This is because the bandwidth of the amplifier is dominated by the feedback
resistor value and internal dominant-pole capacitor. The ability to control the amplifier gain independently of the
bandwidth constitutes a major advantage of current feedback amplifiers over conventional voltage feedback
amplifiers. Therefore, once a frequency response is found suitable to a particular application, adjust the value
of the gain resistor to increase or decrease the overall amplifier gain.
Finally, it is important to realize the effects of the feedback resistance on distortion. Increasing the resistance
decreases the loop gain and increases the distortion. It is also important to know that decreasing load
impedance increases total harmonic distortion (THD). Typically, the third order harmonic distortion increases
more than the second order harmonic distortion.
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
RF
IIB–
RG
+
–
VI
VO
+
RS
ǒ ǒ ǓǓ ǒ ǒ ǓǓ
IIB+
V
OO
+ VIO 1 )
R
R
F
G
" IIB) RS
1
)
R
R
F
G
" IIB– RF
Figure 53. Output Offset Voltage Model
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
noise calculations and noise figure
Noise can cause errors on very small signals. This is especially true for the receiver amplifiers which are
generally used for amplifying small signals coming over a transmission line. The noise model for current
feedback amplifiers (CFB) is the same as voltage feedback amplifiers (VFB). The only difference between the
two is that the CFB amplifiers generally specify different current noise parameters for each input while VFB
amplifiers usually only specify one noise current parameter. The noise model is shown in Figure 54. This model
includes all of the noise sources as follows:
•
•
•
•
en = amplifier internal voltage noise (nV/√Hz)
IN+ = noninverting current noise (pA/√Hz)
IN– = inverting current noise (pA/√Hz)
eRx = thermal voltage noise associated with each resistor (eRx = 4 kTRx )
eRs
RS
en
Noiseless
+
_
eni
IN+
eno
eRf
RF
eRg
IN–
RG
Ǹǒ Ǔ
Figure 54. Noise Model
The total equivalent input noise density (eni) is calculated by using the following equation:
e
+
ni
Where:
en
2
ǒ
) IN )
Ǔ )ǒ ǒ
2
R
S
IN–
R
ǓǓ
ǒ
Ǔ
ø RG ) 4 kTRs ) 4 kT RF ø RG
F
2
k = Boltzmann’s constant = 1.380658 × 10–23
T = temperature in degrees Kelvin (273 +°C)
RF || RG = parallel resistance of RF and RG
ǒ Ǔ
To get the equivalent output noise of the amplifier, just multiply the equivalent input noise density (eni) by the
overall amplifier gain (AV).
e no
28
+ eni AV + e
ni
1
) RR
F
(Noninverting Case)
G
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
noise calculations and noise figure (continued)
As the previous equations show, to keep noise at a minimum, small value resistors should be used. As the
closed-loop gain is increased (by reducing RG), the input noise is reduced considerably because of the parallel
resistance term. This leads to the general conclusion that the most dominant noise sources are the source
resistor (RS) and the internal amplifier noise voltage (en). Because noise is summed in a root-mean-squares
method, noise sources smaller than 25% of the largest noise source can be effectively ignored. This can greatly
simplify the formula and make noise calculations much easier to calculate.
This brings up another noise measurement usually preferred in RF applications, the noise figure (NF). Noise
figure is a measure of noise degradation caused by the amplifier. The value of the source resistance must be
defined and is typically 50 Ω in RF applications.
NF
+ 10log
ȱȧ ȳȧ
Ȳ ȴ
e 2
ni
e
Rs
Because the dominant noise components are generally the source resistance and the internal amplifier noise
voltage, we can approximate noise figure as:
ȱȧ ȡȧǒ
ȧȧ )Ȣ
ȧȲ
2
e
NF
+ 10log
1
Ǔ )ǒ )
n
IN
4 kTR
Ǔ ȣȧȤȳȧ
2
R
S
S
ȧȧ
ȧȴ
The Figure 55 shows the noise figure graph for the THS6002.
NOISE FIGURE
vs
SOURCE RESISTANCE
20
18
TA = 25°C
Noise Figure – dB
16
14
12
10
8
6
4
2
0
10
100
1k
10k
Rs – Source Resistance – Ω
Figure 55. Noise Figure vs. Source Resistance
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
PCB design considerations
Proper PCB design techniques in two areas are important to assure proper operation of the THS6002. These
areas are high-speed layout techniques and thermal-management techniques. Because the THS6002 is a
high-speed part, the following guidelines are recommended.
D
D
Ground plane – It is essential that a ground plane be used on the board to provide all components with a
low inductive ground connection. Although a ground connection directly to a terminal of the THS6002 is not
necessarily required, it is recommended that the thermal pad of the package be tied to ground. This serves
two functions. It provides a low inductive ground to the device substrate to minimize internal crosstalk and
it provides the path for heat removal.
Input stray capacitance – To minimize potential problems with amplifier oscillation, the capacitance at the
inverting input of the amplifiers must be kept to a minimum. To do this, PCB trace runs to the inverting input
must be as short as possible, the ground plane must be removed under any etch runs connected to the
inverting input, and external components should be placed as close as possible to the inverting input. This
is especially true in the noninverting configuration. An example of this can be seen in Figure 56, which shows
what happens when 1.8 pF is added to the inverting input terminal in the noninverting configuration. The
bandwidth increases dramatically at the expense of peaking. This is because some of the error current is
flowing through the stray capacitor instead of the inverting node of the amplifier. Although, in the inverting
mode, stray capacitance at the inverting input has little effect. This is because the inverting node is at a
virtual ground and the voltage does not fluctuate nearly as much as in the noninverting configuration.
DRIVER
NORMALIZED FREQUENCY RESPONSE
vs
FREQUENCY
Normalized Frequency Response – dB
3
2
1
VCC = ±15 V
VI = 200 mV
RL = 25 Ω
RF = 1 kΩ
Gain = 1
0
CI = 0 pF
(Stray C Only)
–1
–2
CI = 1.8 pF
1 kΩ
–3
–4
Cin
Vin
–5
–6
–7
100
Vout
–
+
50 Ω
RL =
25 Ω
1M
10M
100M
500M
f – Frequency – Hz
Figure 56. Driver Normalized Frequency Response vs. Frequency
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
PCB design considerations (continued)
D
Proper power supply decoupling – Use a minimum of a 6.8-µF tantalum capacitor in parallel with a 0.1-µF
ceramic capacitor on each supply terminal. It may be possible to share the tantalum among several
amplifiers depending on the application, but a 0.1-µF ceramic capacitor should always be used on the
supply terminal of every amplifier. In addition, the 0.1-µF capacitor should be placed as close as possible
to the supply terminal. As this distance increases, the inductance in the connecting etch makes the capacitor
less effective. The designer should strive for distances of less than 0.1 inches between the device power
terminal and the ceramic capacitors.
Because of its power dissipation, proper thermal management of the THS6002 is required. Although there are
many ways to properly heatsink this device, the following steps illustrate one recommended approach for a
multilayer PCB with an internal ground plane.
1. Prepare the PCB with a top side etch pattern as shown in Figure 57. There should be etch for the leads as
well as etch for the thermal pad.
2. Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. They are kept
small so that solder wicking through the holes is not a problem during reflow.
3. Place four more holes under the package, but outside the thermal pad area. These holes are 25 mils in
diameter. They may be larger because they are not in the area to be soldered so that wicking is not a
problem.
4. Connect all nine holes, the five within the thermal pad area and the four outside the pad area, to the internal
ground plane.
5. When connecting these holes to the ground plane, do not use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
However, in this application, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS6002 package should make their connection to the internal ground plane with a
complete connection around the entire circumference of the plated through hole.
6. The top-side solder mask should leave exposed the terminals of the package and the thermal pad area with
its five holes. The four larger holes outside the thermal pad area, but still under the package, should be
covered with solder mask.
7. Apply solder paste to the exposed thermal pad area and all of the operational amplifier terminals.
8. With these preparatory steps in place, the THS6002 is simply placed in position and run through the solder
reflow operation as any standard surface mount component. This results in a part that is properly installed.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
PCB design considerations (continued)
Additional 4 vias outside of thermal pad area
but under the package
(Via diameter = 25 mils)
Thermal pad area (0.15 x 0.17) with 5 vias
(Via diameter = 13 mils)
Figure 57. PowerPad PCB Etch and Via Pattern
The actual thermal performance achieved with the THS6002 in its PowerPAD package depends on the
application. In the previous example, if the size of the internal ground plane is approximately 3 inches × 3 inches,
then the expected thermal coefficient, θJA, is about 21.5_C/W. For a given θJA, the maximum power dissipation
is shown in Figure 58 and is calculated by the following formula:
P
D
+
ǒ Ǔ
T
–T
MAX A
q JA
Where:
PD = Maximum power dissipation of THS6002 (watts)
TMAX = Absolute maximum junction temperature (150°C)
TA
= Free-ambient air temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to case (0.37°C/W)
θCA = Thermal coefficient from case to ambient
More complete details of the PowerPAD installation process and thermal management techniques can be found
in the Texas Instruments Technical Brief, PowerPAD Thermally Enhanced Package. This document can be
found at the TI web site (www.ti.com) by searching on the key word PowerPAD. The document can also be
ordered through your local TI sales office. Refer to literature number SLMA002 when ordering.
32
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
PCB design considerations (continued)
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
9
Tj = 150°C
PCB Size = 3” x 3”
No Air Flow
Maximum Power Dissipation – W
8
7
θJA = 21.5°C/W
2 oz Trace and
Copper Pad
with Solder
6
5
4
3
2
θJA = 43.9°C/W
2 oz Trace and Copper Pad
without Solder
1
0
–40
–20
0
20
40
60
80
100
TA – Free-Air Temperature – °C
Figure 58. Maximum Power Dissipation vs Free-Air Temperature
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
ADSL
The THS6002 was primarily designed as a line driver and line receiver for ADSL (asymmetrical digital subscriber
line). The driver output stage has been sized to provide full ADSL power levels of 20 dBm onto the telephone
lines. Although actual driver output peak voltages and currents vary with each particular ADSL application, the
THS6002 is specified for a minimum full output current of 400 mA at its full output voltage of approximately 12
V. This performance meets the demanding needs of ADSL at the central office end of the telephone line. A typical
ADSL schematic is shown in Figure 59.
15 V
0.1 µF
THS6002
Driver 1
VI+
+
6.8 µF
12.5 Ω
+
_
1:2
1 kΩ
100 Ω
To Telephone Line
1 kΩ
0.1 µF
6.8 µF
+
–15 V
1 kΩ
15 V
THS6002
Driver 2
VI–
15 V
0.1 µF
+
2 kΩ
6.8 µF
0.1 µF
12.5 Ω
+
_
1 kΩ
–
+
1 kΩ
THS6002
Receiver 1
VO+
–15 V
1 kΩ
0.1 µF
1 kΩ
6.8 µF
+
15 V
–15 V
2 kΩ
0.1 µF
1 kΩ
–
+
VO–
THS6002
Receiver 2
0.01 µF
–15 V
Figure 59. THS6002 ADSL Application
34
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
ADSL (continued)
The ADSL transmit band consists of 255 separate carrier frequencies each with its own modulation and
amplitude level. With such an implementation, it is imperative that signals put onto the telephone line have as
low a distortion as possible. This is because any distortion either interferes directly with other ADSL carrier
frequencies or it creates intermodulation products that interfere with ADSL carrier frequencies.
The THS6002 has been specifically designed for ultra low distortion by careful circuit implementation and by
taking advantage of the superb characteristics of the complementary bipolar process. Driver single-ended
distortion measurements are shown in Figure 23. It is commonly known that in the differential driver
configuration, the second order harmonics tend to cancel out. Thus, the dominant total harmonic distortion
(THD) will be primarily due to the third order harmonics. For this test, the load was 25 Ω and the output signal
produced a 20 VO(PP) signal. Thus, the test was run at full signal and full load conditions. Because the feedback
resistor used for the test was 4 kΩ, the distortion numbers are actually in a worst-case scenario. Distortion
should be reduced as the feedback resistance drops. This is because the bandwidth of the amplifier increases
dramatically, which allows the amplifier to react faster to any nonlinearities in the closed-loop system.
Another significant point is the fact that distortion decreases as the impedance load increases. This is because
the output resistance of the amplifier becomes less significant as compared to the output load resistance.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
35
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
HDSL
Shown in Figure 60 is an example of the THS6002 being used for HDSL-2 applications. The receiver amplifiers
within the THS6002 have been configured as predrivers for the driver amplifiers. This dual composite amplifier
setup has the effect of raising the open loop gain for the combination of both amplifiers, thereby giving improved
distortion performance.
7.5 kΩ
1 kΩ
11 kΩ
12 V
12 V
6
Receiver 1
–
7
+
9
THS6002
4
+
5
2
30 Ω
–
1:1.5
Driver 1
Output
27.4 VO(PP)
–12 V
–12 V
135 Ω
1 kΩ
511 Ω
Input
3 V(PP)
1 kΩ
1 kΩ
7.5 kΩ
12 V
2
U2
–
1
+
6
1 kΩ
11 kΩ
THS4001
12 V
12 V
15
–12 V
Receiver 2
–
14
+
12
17
+
16
19
30 Ω
–
Driver 2
–12 V
–12 V
1 kΩ
511 Ω
Figure 60. HDSL-2 Line Driver
general configurations
A common error for the first-time CFB user is to create a unity gain buffer amplifier by shorting the output directly
to the inverting input. A CFB amplifier in this configuration is now commonly referred to as an oscillator. The
THS6002, like all CFB amplifiers, must have a feedback resistor for stable operation. Additionally, placing
capacitors directly from the output to the inverting input is not recommended. This is because, at high
frequencies, a capacitor has a very low impedance. This results in an unstable amplifier and should not be
considered when using a current-feedback amplifier. Because of this, integrators and simple low-pass filters,
which are easily implemented on a VFB amplifier, have to be designed slightly differently. If filtering is required,
simply place an RC-filter at the noninverting terminal of the operational-amplifier (see Figure 61).
36
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
ǒ Ǔǒ
general configurations (continued)
RG
RF
+ 1 ) RRF
V
O
V
I
–
VO
+
VI
R1
f
1
G
–3dB
C1
Ǔ
) sR1C1
1
1
+ 2pR1C1
Figure 61. Single-Pole Low-Pass Filter
If a multiple pole filter is required, the use of a Sallen-Key filter can work very well with CFB amplifiers. This is
because the filtering elements are not in the negative feedback loop and stability is not compromised. Because
of their high slew-rates and high bandwidths, CFB amplifiers can create very accurate signals and help minimize
distortion. An example is shown in Figure 62.
C1
+
_
VI
R1
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
R2
f
C2
RG =
RF
RG
–3dB
+ 2p1RC
(
RF
1
2–
Q
)
Figure 62. 2-Pole Low-Pass Sallen-Key Filter
There are two simple ways to create an integrator with a CFB amplifier. The first one shown in Figure 63 adds
a resistor in series with the capacitor. This is acceptable because at high frequencies, the resistor is dominant
and the feedback impedance never drops below the resistor value. The second one shown in Figure 64 uses
positive feedback to create the integration. Caution is advised because oscillations can occur because of the
positive feedback.
C1
RF
RG
VI
–
+
VO
THS6002
V
O
V
I
+
ǒ
R
R
ȡǓȧ ) ȣȧ
Ȣ Ȥ
S
F
G
1
R C1
F
S
Figure 63. Inverting CFB Integrator
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
37
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
APPLICATION INFORMATION
general configurations (continued)
RG
RF
For Stable Operation:
–
THS6002
R1
VO
+
R2
R1 || RA
≥
(
1+
VO ≅ VI
R2
VI
RF
RG
RF
RG
sR1C1
)
C1
RA
Figure 64. Non-Inverting CFB Integrator
Another good use for the THS6002 driver amplifiers are as very good video distribution amplifiers. One
characteristic of distribution amplifiers is the fact that the differential phase (DP) and the differential gain (DG)
are compromised as the number of lines increases and the closed-loop gain increases. Be sure to use
termination resistors throughout the distribution system to minimize reflections and capacitive loading.
620 Ω
620 Ω
75 Ω Transmission Line
75 Ω
–
VO1
+
VI
75 Ω
75 Ω
THS6002
N Lines
75 Ω
VON
75 Ω
Figure 65. Video Distribution Amplifier Application
evaluation board
An evaluation board is available for the THS6002 (literature number SLOP117). This board has been configured
for proper thermal management of the THS6002. The circuitry has been designed for a typical ADSL application
as shown previously in this document. For more detailed information, refer to the THS6002EVM User’s Manual
(literature number SLOU018). To order the evaluation board contact your local TI sales office or distributor.
38
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
THS6002
DUAL DIFFERENTIAL LINE DRIVERS AND RECEIVERS
SLOS202D– JANUARY 1998– REVISED JULY 1999
MECHANICAL INFORMATION
DWP (R-PDSO-G20)
PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
0.020 (0,51)
0.014 (0,35)
0.050 (1,27)
20
0.010 (0,25) M
11
Thermal Pad 0.150 (3,81)
(see Note C)
0.170 (4,31) NOM
0.299 (7,59)
0.293 (7,45)
0.430 (10,92)
0.411 (10,44)
0.010 (0,25) NOM
1
10
0.510 (12,95)
0.500 (12,70)
Gage Plane
0.010 (0,25)
+2°– 8°
0.050 (1,27)
0.016 (0,40)
Seating Plane
0.096 (2,43) MAX
0.004 (0,10)
0.000 (0,00)
0.004 (0,10)
4073226/B 01/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. The thermal performance may be enhanced by bonding the thermal pad to an external thermal plane.
PowerPAD is a trademark of Texas Instruments Incorporated.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
39
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated