TI TMS320VC5470GHK

TMS320VC5470 Fixed-Point
Digital Signal Processor
Data Manual
Literature Number: SPRS017B
December 2001 – Revised December 2002
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated
REVISION HISTORY
REVISION
DATE
PRODUCT STATUS
HIGHLIGHTS
*
December 2001
Production Data
Original
A
July 2002
Production Data
Updated ARM SRAM read and write timing diagrams
B
December 2002
Production Data
Added industrial temperature specifications to the Recommended
Operating Conditions and the Absolute Maximum Ratings (page 44).
Updated mechanical diagram (page 82)
iii
iv
Contents
Contents
Section
Page
1
TMS320VC5470 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
4
7
3
DSP Subsystem Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
DSP Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
DSP Memory Space and Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2
DSP Scan-Based Emulation Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
DSP Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
DSP On-Chip RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Normal Mode DSP Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
API Boot Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4
API Boot-Mode DSP Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5
DSP Extended Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6
DSP Relocatable Interrupt Vector Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
DSP Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1
Bank-Switching Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2
Programmable Bank-Switching Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3
Processor Mode Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
DSP Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1
Multichannel Buffered Serial Port (McBSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.2
DSP Direct Memory Access (DMA) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.3
ARM Port Interface (API) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.4
DSP External Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.5
DSP Software-Programmable Wait-State Generator . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.6
DSP Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.7
DSP Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
DSP Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6
DSP Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
12
12
12
12
13
14
15
15
16
18
19
20
21
21
22
23
24
24
24
24
25
26
4
MCU Subsystem Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
MCU Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.1
ARM7TDMI Emulation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1.2
MCU Memory Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
MCU Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
MCU Memory Interface Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
MCU API Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
MCU SDRAM Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
28
28
29
30
30
30
31
December 2001 – Revised December 2002
SPRS017B
v
Contents
Section
4.3
Page
MCU Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
MCU Universal Asynchronous Receiver/Transmitter (UART) Interfaces . . . . . . . . .
4.3.2
MCU Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
MCU General-Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.4
MCU Inter-Integrated Circuit (I2C) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5
MCU Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.6
MCU Interrupt Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCU Power-Down Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCU Peripheral Clock Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.1
Initial MCU Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.2
DSP Boot Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.3
Emulation Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
34
34
36
36
37
38
39
40
40
41
41
5
Documentation Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
6
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
Electrical Characteristics Over Recommended Operating Case
Temperature (Unless Otherwise Noted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4
Package Thermal Resistance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5
Timing Parameter Symbology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.1
Divide-By-Two/Divide-By-Four Clock Option Timing . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.2
Multiply-By-N Clock Option (PLL Enabled) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
Memory and Parallel I/O Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.1
Memory Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2
Memory Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.3
Parallel I/O Port Read Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.4
Parallel I/O Port Write Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7
Ready Timing for Externally Generated Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8
Interrupt Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.9
Instruction Acquisition (DSP_IAQ) and Interrupt Acknowledge (DSP_IACK) Timings . . . . . . .
6.10
External Flag (DSP_XF) and DSP_TOUT Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11
Multichannel Buffered Serial Port (McBSP) Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11.1
McBSP Receive and Transmit Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11.2
McBSP General-Purpose Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11.3
McBSP as SPI Master or Slave Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.12
Synchronous DRAM Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.13
I2C Bus Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.14
ARM Clock Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.15
SPI Clock Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
44
44
Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
Ball Grid Array Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
82
4.4
4.5
4.6
7
vi
SPRS017B
45
46
46
47
48
49
49
51
53
54
55
58
59
60
61
61
64
65
69
73
75
79
December 2001 – Revised December 2002
Figures
List of Figures
Figure
2–1
5470 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
257-Ball GHK Package (Bottom View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
3
4
3–1
3–2
3–3
3–4
3–5
3–6
3–7
5470 DSP Subsystem Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Map for DSP Accesses (DSP_APIBN = 1 or ABMDIS = 1) . . . . . . . . . . . . . . . . . . . . . . . . .
API Boot Mode Memory Map for DSP Accesses (DSP_APIBN = 0 and ABMDIS = 0) . . . . . . . . . .
DSP Extended Program Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank-Switching Control Register (BSCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Control Register (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IFR and IMR Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
13
14
15
18
21
27
4–1
4–2
5470 MCU Subsystem Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
39
6–1
6–2
6–3
6–4
6–5
6–6
6–7
6–8
6–9
6–10
6–11
6–12
6–13
6–14
6–15
6–16
6–17
6–18
6–19
6–20
6–21
6–22
6–23
6–24
6–25
6–26
6–27
3.3-V Test Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Divide-by-Two Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Multiply-by-One Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Read With Externally Generated Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Write With Externally Generated Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Read With Externally Generated Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Write With Externally Generated Wait-States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP_IAQ and DSP_IACK Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP_XF Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP_TOUT Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Receive Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Transmit Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP General-Purpose I/O Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0 . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0 . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1 . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1 . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Read Command (CAS Latency 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Write Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Active Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Precharge Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Deactivate Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
47
48
50
52
53
54
55
56
56
57
58
59
60
60
63
63
64
65
66
67
68
69
70
70
71
71
December 2001 – Revised December 2002
SPRS017B
vii
Figures
Figure
Page
6–28
6–29
6–30
6–31
6–32
6–33
6–34
6–35
6–36
SDRAM Refresh Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDRAM Mode Register Set Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definition of Timing on the I2C Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Bus Timings (STOP and START Conditions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Bus Timings (Repeated START Condition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ARM SRAM Write Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ARM SRAM Read Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Falling Edge Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Rising Edge Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
72
73
74
74
76
78
80
81
7–1
TMS320VC5470 257-Ball MicroStar BGA Plastic Ball Grid Array Package . . . . . . . . . . . . . . . . . . .
82
viii
SPRS017B
December 2001 – Revised December 2002
Tables
List of Tables
Table
2–1
2–2
2–3
Pin Assignments for the GHK Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Pullup/Pulldown Terminal List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
4
7
10
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
CPU Memory-Mapped Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Memory-Mapped Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Control Registers and Subaddresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bank-Switching Control Register (BSCR) Bit Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relationship Between BNKCMP and Bank Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
State of Signals When External Bus Interface is Disabled (EXIO = 1) . . . . . . . . . . . . . . . . . . . . . . .
Sample Rate Generator Clock Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Synchronization Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMA Channel Interrupt Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP Clock Scaler Values and Minimum REFCLK Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP Interrupt Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IFR and IMR Register Bit Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
17
18
19
20
20
21
22
23
23
25
26
27
4–1
4–2
4–3
4–4
4–5
4–6
4–7
4–8
MCU Memory Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO Control/Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPIO_IRQ Bits Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCU Peripheral Interrupt Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP Boot Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emulation Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JTAG TAP Controller Instruction Register Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
35
35
38
40
41
41
42
6–1
6–2
6–3
6–4
6–5
6–6
6–7
6–8
6–9
6–10
6–11
6–12
6–13
6–14
6–15
6–16
6–17
6–18
6–19
Thermal Resistance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Divide-By-Two/Divide-By-Four Clock Option Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . .
Divide-By-Two/Divide-By-Four Clock Option Switching Characteristics . . . . . . . . . . . . . . . . . . . . . .
Multiply-By-N Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiply-By-N Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Read Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Read Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Write Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Read Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Read Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O Port Write Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ready Timing For Externally Generated Wait-States Timing Requirements . . . . . . . . . . . . . . . . . .
Reset and Interrupt Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP_IAQ and DSP_IACK Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSP_XF and DSP_TOUT Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Receive and Transmit Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP Receive and Transmit Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP General-Purpose Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
McBSP General-Purpose Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
47
47
48
48
49
49
51
53
53
54
55
58
59
60
61
62
64
64
December 2001 – Revised December 2002
SPRS017B
ix
Tables
Table
6–20
6–21
6–22
6–23
6–24
6–25
6–26
6–27
6–28
6–29
6–30
6–31
6–32
6–33
6–34
6–35
6–36
6–37
6–38
x
Page
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b and CLKXP = 0) . . . . . . .
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b and CLKXP = 0) . . .
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b and CLKXP = 0) . . . . . . .
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b and CLKXP = 0) . . .
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b and CLKXP = 1) . . . . . . .
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b and CLKXP = 1) . . .
McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b and CLKXP = 1) . . . . . . .
McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b and CLKXP = 1) . . .
Synchronous DRAM Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Synchronous DRAM Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Bus Device Switching Characteristics of the SDA and SCL Bus Lines . . . . . . . . . . . . . . . . . . .
I2C Bus Device Timing Requirements (STOP and START Conditions) . . . . . . . . . . . . . . . . . . . . . .
I2C Bus Device Timing Requirements (Repeated START Condition) . . . . . . . . . . . . . . . . . . . . . . . .
ARM SRAM Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ARM SRAM Timing Requirements (Write) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ARM SRAM Timing Requirements (Read) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Clock Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Falling Edge Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Rising Edge Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPRS017B
65
65
66
66
67
67
68
68
69
69
73
74
74
75
75
77
79
79
81
December 2001 – Revised December 2002
Features
1
TMS320VC5470 Features
D Dual CPU Processor Integrating a
D
D
D
TMS320C54x DSP and an ARM7TDMI
RISC MCU
16-Bit Low-Power DSP With 72K x 16-bit
Integrated SRAM Operates at up to
100 MHz
Smart Power Management and Low-Power
Modes for DSP and MCU Subsystems
Integrated DSP Subsystem Peripherals
– Two High-Speed, Full-Duplex
Multichannel Buffered Serial Ports
(McBSPs) Allowing the DSP Core to
Interface Directly With CODECs
– Six-Channel Direct Memory Access
(DMA) Controller Enabling Six
Independent Block Transfers With No
Intervention From the DSP
– ARM Port Interface (API) Provides
2K x 16-Bit Shared Memory Interface for
Efficient Information Exchange Between
the MCU Subsystem and the DSP
Subsystem CPUs
– External Memory Interface
– Software-Programmable Wait-State
Generator Capable of Extending
External Bus Cycles By Up To
14 Machine Cycles
– One Software-Programmable Hardware
Timer For Control Operations
– Programmable Phase-Locked Loop
(PLL) Clock Generator
D ARM7TDMI RISC Microcontroller Core With
D
D
D
D
16K Bytes of Integrated SRAM and
Enhanced Emulation Capabilities Operates
at Up To 47.5 MHz
Integrated MCU Subsystem Peripherals
– Universal Asynchronous Receiver/
Transmitter (UART)
– UART/IrDA Interface Which Supports the
Slow Infrared (SIR) Protocol
– Serial Peripheral Interface
– Thirty-Six General-Purpose I/O Pins
– Inter-Integrated Circuit (I2C) Interface
– Two General-Purpose Timers
– One Watchdog Timer
– Interrupt Handler
– Interface to External Memory Supports
Flash, SRAM, SDRAM, ROM
– Flexible Clock Management for MCU
Peripherals
– Programmable Phase-Locked Loop
(PLL) Clock Generator
On-Chip Scan-Based Emulation Logic,
IEEE Std 1149.1† (JTAG) Boundary Scan
Logic of DSP and MCU Cores
Supports Scan-Based Emulation of DSP
and MCU Cores
257-Ball MicroStar BGA (GHK Suffix)
Package
† IEEE Standard 1149.1-1990Standard-Test-Access Port and Boundary Scan Architecture.
TMS320C54x and MicroStar BGA are trademarks of Texas Instruments.
ARM7TDMI is a trademark of ARM Limited.
ARM is a registered trademark of ARM Limited.
Other trademarks are the property of their respective owners.
December 2001 – Revised December 2002
SPRS017B
1
Introduction
2
Introduction
This section describes the main features, gives a brief functional overview of the TMS320VC5470, lists the
pin assignments, and provides a signal description table. The data manual also provides a detailed description
section, electrical specifications, parameter measurement information, and mechanical data section
describing the available packaging.
NOTE: This data manual is designed to be used in conjunction with the TMS320C54x DSP
Functional Overview (literature number SPRU307) and the TMS320VC547x CPU and
Peripherals Reference Guide (literature number SPRU038).
2.1
Description
The TMS320VC5470 integrates a DSP subsystem based on the TMS320C54x architecture and a RISC
microcontroller subsystem based on the ARM7TDMI core as shown in Figure 2–1. The DSP subsystem
includes 72K x 16-bit SRAM, a timer, a DMA controller, an external memory interface, and two McBSPs. The
MCU subsystem includes three timers, general-purpose I/O, and an external memory interface.
The TMS320VC5470 is implemented as two major subsystems that are highly independent. The DSP
subsystem includes the following modules:
•
•
•
•
•
•
•
•
•
TMS320C54x DSP core
72K x 16-bit internal SRAM organized as 32K x 16-bit of data SRAM and 40K x 16-bit of program SRAM.
ARM port interface (API) to provide access by the MCU to 8K x 16 of the DSP’s data SRAM
Two multichannel buffered serial ports (McBSPs)
Phase-locked loop (PLL)
Timer
Direct memory access (DMA) controller
Programmable wait-state generator
External memory interface
The MCU subsystem includes the following modules:
•
•
•
•
•
•
•
•
•
•
•
•
2
ARM7TDMI CPU core (32/16-bit RISC processor) with extended emulation capabilities
MCU memory interface for external SRAM, Flash, ROM, and SDRAM.
On-chip 16K-byte (4K x 32) zero wait-state SRAM.
MCU general-purpose I/Os (GPIOs), including support for an 8 x 8 keyboard.
Three timers (two general-purpose, one watchdog)
IrDA-compatible UART, supporting two modes
– IrDA mode
– UART mode without hardware flow control
UART/Modem, with
– hardware flow control support
– autobaud function
MCU subsystem interrupt handler
Clock generator and control
I2C “master-only” interface
Serial peripheral interface
Phase-locked loop (PLL)
SPRS017B
December 2001 – Revised December 2002
Introduction
DSP Subsystem
CODEC
McBSP
McBSP
DMA
TIMER
XIO
External
DSP
Memory
CODEC
8 K × 16
Data RAM
8 K × 16
Prog RAM
C54x DSP
8 K × 16
Prog RAM
8 K × 16
Data RAM
8 K × 16
Prog RAM
8 K × 16
Data RAM
8 K × 16
Data RAM
API
PLL
8 K × 16
Prog RAM
8 K × 16
Prog RAM
MCU Subsystem
ASYNC,
FLASH,
SDRAM,
etc.
Memory I/F
DSPSS
I/F
Clock
Oscillator
PLL
Clock
Manager
4K × 32 RAM
I2C Device
GeneralPurpose
I/Os
RS232
Transceiver
UART/IRDA
IRDA
Transceiver
SPI
SPI Device
I2C
ARM7TDMIE
Keypad
UART
GPIO/Keypad
Watchdog
Timer
Timer
Interrupt
Handler
TMS320VC5470
Figure 2–1. 5470 Functional Block Diagram
C54x is a trademark of Texas Instruments.
December 2001 – Revised December 2002
SPRS017B
3
Introduction
2.2
Pin Assignments
Figure 2–2 illustrates the ball locations for the 257-ball ball grid array (BGA) package and is used in
conjunction with Table 2–1 to locate signal names and ball grid numbers.
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
3
2
5
4
7
6
9
8
11
10
12
13 15 17 19
14 16 18
Figure 2–2. 257-Ball GHK Package (Bottom View)
Table 2–1. Pin Assignments for the GHK Package
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
B2
GPIO02
B1
GPIO03
D3
GPIO04
C2
GPIO05/
SDRAM_CKE
C1
GPIO06/
CLK16X_IRDA/SD_IRDA
D2
GPIO07/
TX_IRDA/TXIR_IRDA
D1
GPIO08/
RX_IRDA/RXIR_IRDA
E3
DVDD
F5
GPIO09/
TX_MODEM
G6
VSS
E2
GPIO10/
RX_MODEM
E1
GPIO11/
CTS_MODEM
F3
GPIO12/
RTS_MODEM
F2
GPIO13/
DCD_MODEM
G5
CVDD
F1
GPIO18/
AUDIO_CLK
H6
GPIO19/
TIMER_OUT
G3
GPIO00
G2
GPIO14/
MCUEN2
G1
GPIO16/
SDA
H5
DVDD
H3
GPIO17/
SCL
H2
VSS
H1
KBGPIO14/
DSP_CLKOUT
J1
KBGPIO02/
ARM_OPC
J2
KBGPIO03/
ARM_MREQ
J3
KBGPIO04/
ARM_EXEC
J5
KBGPIO06/
ARM_FIQ
J6
KBGPIO07/
ARM_IRQ
K1
KBGPIO13/
DSP_TOUT
K2
KBGPIO11/
DSP_IAQ
K3
CVDD
K5
KBGPIO05/
ARM_TBIT
K6
KBGPIO01/
DSP_XF
L1
KBGPIO15/
ARM_MCLK
L2
KBGPIO00
L3
VSS
L6
KBGPIO12/
DSP_MSC
L5
KBGPIO10/
DSP_IACK
M1
KBGPIO08
NOTE: DVDD is the 3.3 V power supply for the I/O pins while CVDD is the 1.8 V power supply for the core CPU. VSS is the ground for both the
I/O pins and the core CPU.
4
SPRS017B
December 2001 – Revised December 2002
Introduction
Table 2–1. Pin Assignments for the GHK Package (Continued)
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
M2
KBGPIO09
M3
GPIO01
M6
GPIO15/
MCUEN1
M5
CLKX_SPI
N1
MCUDI/
EXTERN0
N2
MCUDO/
EXTERN1
N3
DVDD
N6
MCUEN0
P1
N/C
P2
N/C
N5
VSS
P3
N/C
R1
N/C
P6
N/C
R2
N/C
P5
CVDD
R3
N/C
T1
N/C
T2
N/C
U1
N/C
T3
DVDD
U2
N/C
V1
N/C
U3
N/C
V2
N/C
W2
N/C
U4
N/C
V3
N/C
W3
N/C
V4
N/C
W4
N/C
U5
N/C
R6
VSS
P7
N/C
V5
N/C
W5
N/C
U6
DVDD
V6
N/C
R7
N/C
W6
N/C
P8
N/C
U7
N/C
V7
N/C
W7
N/C
R8
CVDD
U8
N/C
V8
EMU1
W8
TRST
W9
TCK
V9
TDI
U9
VSS
R9
TDO
P9
DVDD
W10
TMS
V10
EMU0
U10
REFCLK
R10
RESET
P10
RESET_OUT
W11
ADD17
V11
ADD16
U11
ADD15
P11
ADD14
R11
ADD13
W12
ADD12/
SDRAM_A12
V12
ADD11/
SDRAM_A11
U12
VSS
P12
ADD10/
SDRAM_A10
R12
DVDD
W13
ADD01/
SDRAM_A01
V13
ADD09/
SDRAM_A09
U13
ADD08/
SDRAM_A08
P13
ADD07/
SDRAM_A07
W14
ADD06/
SDRAM_A06
V14
ADD05/
SDRAM_A05
R13
CVDD
U14
ADD04/
SDRAM_A04
W15
ADD03/
SDRAM_A03
P14
VSS
V15
ADD02/
SDRAM_A02
R14
DVDD
U15
ADD00/
SDRAM_A00
W16
ADD18/
SDRAM_BA0
V16
ADD19
SDRAM_BA1
W17
ADD20/
SDRAM_WE
U16
ADD21/
SDRAM_CAS
V17
ADD22/
SDRAM_RAS
W18
CS4/
BIGEND
U17
DATA00
V18
DATA01
V19
DATA02
T17
VSS
U18
DATA03
U19
DATA04
T18
DVDD
T19
DATA05
R17
DATA06
P15
DATA07
N14
CVDD
R18
DATA08
R19
DATA09
P17
DATA10
P18
DATA11
N15
VSS
P19
DATA12
M14
DVDD
N17
DATA13
N18
DATA14
N19
DATA15
M15
DATA16
M17
DATA17
M18
DATA18
M19
DATA19
L19
DATA20
L18
DATA21
L17
VSS
L15
DATA22
K18
DVDD
K17
BE1/
SDRAM_DQM1
L14
DATA23
K19
BE0/
SDRAM_DQM0
K15
BE2/
SDRAM_DQM2
K14
BE3/
SDRAM_DQM3
J19
CS0
J18
CS1
J17
CS2
J14
CS3/
ROMSIZE16
J15
VSS
H19
OE
H18
WAIT
H17
DVDD
H14
R/W
H15
SDRAM_CLK
G19
SDRAM_CS
G18
DATA24
G17
CVDD
G14
DATA25
F19
DATA26
F18
DATA27
G15
VSS
F17
DATA28
NOTE: DVDD is the 3.3 V power supply for the I/O pins while CVDD is the 1.8 V power supply for the core CPU. VSS is the ground for both the
I/O pins and the core CPU.
December 2001 – Revised December 2002
SPRS017B
5
Introduction
Table 2–1. Pin Assignments for the GHK Package (Continued)
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
BALL
NO.
SIGNAL
NAME
E19
DATA29
F14
DATA30
E18
DATA31
F15
DVDD
BDR0
E17
BDX0
D19
BFSX0
D18
BCLKX0
C19
D17
VSS
C18
BCLKR0
B19
BFSR0
C17
BDR1
B18
BFSR1
A18
BCLKR1
C16
BFSX1
B17
BCLKX1
A17
BDX1
B16
DSP_A00
A16
DSP_A01
C15
DSP_A02
E14
DVDD
F13
VSS
B15
DSP_A03
A15
DSP_A04
C14
DSP_A05
B14
DSP_A06
E13
DSP_A07
A14
DSP_A08
F12
VSS
C13
DSP_A09
B13
DSP_A10
A13
DSP_A11
E12
DVDD
C12
DSP_A12
B12
DSP_A13
A12
DSP_A14
A11
DSP_A15
B11
DSP_A16
C11
VSS
E11
DSP_A17
F11
DSP_A18
A10
DSP_A19
B10
CVDD
C10
DSP_D00
E10
DVDD
F10
DSP_D01
A9
DSP_D02
B9
DSP_D03
C9
VSS
F9
DSP_D04
E9
DSP_D05
A8
DSP_D06
B8
DSP_D07
C8
DVDD
F8
DSP_D08
E8
DSP_D09
A7
DSP_D10
B7
DSP_D11
C7
VSS
F7
DSP_D12
A6
DSP_D13
B6
DSP_D14
E7
DVDD
C6
DSP_D15
A5
CVDD
F6
DSP_MSTRB
B5
DSP_DS
E6
VSS
C5
DSP_INT0
A4
DSP_IOSTRB
B4
DSP_IS
A3
DSP_PS
C4
DVDD
B3
DSP_READY
A2
DSP_R/W
C3
VSS
E5
N/C
NOTE: DVDD is the 3.3 V power supply for the I/O pins while CVDD is the 1.8 V power supply for the core CPU. VSS is the ground for both the
I/O pins and the core CPU.
6
SPRS017B
December 2001 – Revised December 2002
Introduction
2.3
Terminal Functions
Table 2–2 lists each terminal name, function, and operating mode(s) for the 5470 device. Some of the 5470
pins can be configured for one of two functions — a primary function and a secondary function. Table 2–3
provides a list of pins containing an internal pullup or pulldown function, including each pins functional pullup
or pulldown value.
Table 2–2. Terminal Functions
TERMINAL NAME
I/O/Z†
DESCRIPTION
GPIO00–GPIO04
I/O
General-purpose input/output 00 through general-purpose input/output 04
GPIO05/SDRAM_CKE
I/O
General-purpose input/output 05 or SDRAM CKE signal
GPIO06/CLK16X_IRDA/SD_IRDA
I/O
General-purpose input/output 06 or 16x Serial Transmit Clock or IRDA Transceiver Shutdown
GPIO07/TX_IRDA/TXIR_IRDA
I/O
General-purpose input/output 07 or IRDA Transmit Data or IRDA Transmit Pulse
GPIO08/RX_IRDA/RXIR_IRDA
I/O
General-purpose input/output 08 or IRDA Receive Data or IRDA Receive Pulse
GPIO09/TX_MODEM
I/O
General-purpose input/output 09 or Modem TX Data Output
GPIO10/RX_MODEM
I/O
General-purpose input/output 10 or Modem RX Data Input
GPIO11/CTS_MODEM
I/O
General-purpose input/output 11 or Modem Clear-To-Send Input
GPIO12/RTS_MODEM
I/O
General-purpose input/output 12 or Modem Ready-To-Send Output
GPIO13/DCD_MODEM
I/O
General-purpose input/output 13 or Modem Carrier Detect Output
GPIO14/MCUEN2
I/O
General-purpose input/output 14 or SPI Enable Trigger bit 2
GPIO15/ MCUEN1
I/O
General-purpose input/output 15 or SPI Enable Trigger bit 1
GPIO16/SDA
I/O
General-purpose input/output 16 or I2C Serial Data
GPIO17/SCL
I/O
General-purpose input/output 17 or I2C Serial Clock
GPIO18/AUDIO_CLK
I/O
General-purpose input/output 18 or Audio Clock output
GPIO19/TIMER_OUT
I/O
General-purpose input/output 19 or MCU Timer 2 Output
KBGPIO00
I/O
Keyboard input/output 0
KBGPIO01/DSP_XF
I/O
Keyboard input/output 1or DSP XF output
KBGPIO02/ARM_OPC
I/O
Keyboard input/output 2 or active-low MCU opcode fetch output
KBGPIO03/ARM_MREQ
I/O
Keyboard input/output 3 or active-low MCU memory request output
KBGPIO04/ARM_EXEC
I/O
Keyboard input/output 4 or active-low MCU executed output
KBGPIO05/ARM_TBIT
I/O
Keyboard input/output 5 or MCU 16/32-bit instruction execution output
KBGPIO06/ARM_FIQ
I/O
Keyboard input/output 6 or active-low MCU fast interrupt output
KBGPIO07/ARM_IRQ
I/O
KBGPIO08–KBGPIO09
I/O
Keyboard input/output 7 or MCU normal interrupt output
Keyboard input/output bits 8–9‡
KBGPIO10/DSP_IACK
I/O
Keyboard input/output 10 or DSP interrupt acknowledge output‡
KBGPIO11/DSP_IAQ
I/O
KBGPIO12/DSP_MSC
I/O
Keyboard input/output 11 or active-low DSP instruction acquisition signal output‡
Keyboard input/output 12 or active-low DSP microstate complete signal output‡
KBGPIO13/DSP_TOUT
I/O
KBGPIO14/ DSP_CLKOUT
I/O
Keyboard input/output 13 or DSP timer output‡
Keyboard input/output 14 or DSP clock output‡
KBGPIO15/ARM_MCLK
I/O
Keyboard input/output 15 or MCU clock output‡
CLKX_SPI
O
SPI Serial clock
MCUDI/EXTERN0
I
SPI Input serial data/MCU EXTERN0 test signal input
MCUDO/EXTERN1
I/O
SPI Output serial data/MCU EXTERN1 test signal input
† I = input, O = output, Z = high-impedance
‡ The KBGPIO[15:8] pins include integrated pullup resistors.
§ The ARM7TDMI core can operate in either little- or big-endian mode. The 5470 configures the ARM7TDMI core’s endianness by sampling this
pin at the RESET rising edge.
¶ 5470 only supports MCU boot from a 16-bit or a 32-bit-wide memory implementation on CS0. The 5470 configures the ARM7TDMI starting
instruction size, and width of memory connected to CS0, by sampling this pin at the RESET rising edge.
December 2001 – Revised December 2002
SPRS017B
7
Introduction
Table 2–2. Terminal Functions (Continued)
TERMINAL NAME
I/O/Z†
DESCRIPTION
MCUEN0
O
SPI enable trigger (edge/level, positive/negative)
EMU0–EMU1
I/O
Test emulation pins 0 and 1, active-low
TRST
I
Test reset input, active-low. A pulldown resistor is suggested to allow both normal device
operation and emulation.
TCK
I
Test Clock
TDI
I
Test Data Input
TDO
O
Test Data Output
TMS
I
Test Mode Select
REFCLK
I
Reference input clock
RESET
I
Chip power-on reset, active-low§¶
RESET_OUT
O
Reset to external peripherals, active-low
ADD00/ SDRAM_A00 –
ADD12/SDRAM_A12
O
MCU address bus bits 0 through 12 for Flash, SRAM, and SDRAM
ADD13–ADD17
O
MCU address bus bits 13 through 17 for Flash and SRAM
ADD18/ SDRAM_BA0
O
MCU address bus bit 18 for Flash and SRAM or SDRAM BA0 signal
ADD19/ SDRAM_BA1
O
MCU address bus bit 19 for Flash and SRAM or SDRAM BA1 signal
ADD20/ SDRAM_WE
O
MCU address bus bit 20 for Flash and SRAM or active-low SDRAM WE signal
ADD21/ SDRAM_CAS
O
MCU address bus bit 21 for Flash and SRAM or active-low SDRAM CAS signal
ADD22/ SDRAM_RAS
O
MCU address bus bit 22 for Flash and SRAM or active-low SDRAM RAS signal
MCU Chip Select 4 (active-high).§ This pin is sampled at the RESET rising edge to determine
the endian mode as defined below:
CS4/ BIGEND
I/O
0 = Little Endian
1 = Big Endian
For best results, an external pullup or pulldown should be installed to ensure proper sampling.
DATA00–DATA31
I/O
MCU data bus bits 0 through 31 for Flash, SRAM, and SDRAM
BE0/ SDRAM_DQM0
O
MCU byte-enable for non-SDRAM cycles, or SDRAM byte-enable (for read) and mask
(for write), active-low
BE1/ SDRAM_DQM1
O
MCU byte-enable for non-SDRAM cycles, or SDRAM byte-enable (for read) and mask
(for write), active-low
BE2/ SDRAM_DQM2
O
MCU byte-enable for non-SDRAM cycles, or SDRAM byte-enable (for read) and mask
(for write), active-low
BE3/ SDRAM_DQM3
O
MCU byte-enable for non-SDRAM cycles, or SDRAM byte-enable (for read) and mask
(for write), active-low
CS0
O
MCU chip select 0, active-low
CS1
O
MCU chip select 1, active-low
CS2
O
MCU chip select 2, active-low
MCU chip select 3, active-low.¶ Input sampled at RESET rising edge to determine the width of
the ARM processor during initialization as defined below:
CS3/ ROMSIZE16
I/O
0 = 16 bits
1 = 32 bits
For best results, an external pullup or pulldown should be installed to ensure proper sampling.
† I = input, O = output, Z = high-impedance
‡ The KBGPIO[15:8] pins include integrated pullup resistors.
§ The ARM7TDMI core can operate in either little- or big-endian mode. The 5470 configures the ARM7TDMI core’s endianness by sampling this
pin at the RESET rising edge.
¶ 5470 only supports MCU boot from a 16-bit or a 32-bit-wide memory implementation on CS0. The 5470 configures the ARM7TDMI starting
instruction size, and width of memory connected to CS0, by sampling this pin at the RESET rising edge.
8
SPRS017B
December 2001 – Revised December 2002
Introduction
Table 2–2. Terminal Functions (Continued)
TERMINAL NAME
I/O/Z†
DESCRIPTION
OE
O
MCU output-enable for peripherals connected to the MCU memory interface (not for
SDRAM), active-low
WAIT
I
MCU wait request, active-low. If this signal is unused, it must be pulled high with an external
pullup resistor.
R/W
O
Asynchrouous memory active-high read / active-low write signal (not for SDRAM)
SDRAM_CLK
O
SDRAM Clock
O
SDRAM chip-select, active-low
SDRAM_CS
BDX0
O/Z
McBSP0 transmit serial data
BFSX0
I/O/Z
McBSP0 transmit frame synchronization
BCLKX0
I/O/Z
McBSP0 transmit clock
BDR0
I
McBSP0 receive serial data
BCLKR0
I/O/Z
McBSP0 receive clock
BFSR0
I/O/Z
McBSP0 receive frame synchronization
BDR1
I
BFSR1
I/O/Z
McBSP1 receive frame synchronization
BCLKR1
I/O/Z
McBSP1 receive clock
BFSX1
I/O/Z
McBSP1 transmit frame synchronization
BCLKX1
I/O/Z
McBSP1 transmit clock
BDX1
O/Z
McBSP1 transmit data
DSP_A00– DSP_A19
O/Z
DSP Address bits 0 through 19
DSP_D00–DSP_D15
I/O/Z
DSP Data bus bits 0 through 15
DSP_MSTRB
O/Z
DSP memory strobe signal, active-low
DSP_DS
O/Z
DSP data space select, active-low
DSP_INT0
I
McBSP1 receive serial data
DSP external interrupt, active-low. If this signal is unused, it should be pulled high with an
external pullup resistor.
DSP_IOSTRB
O/Z
DSP I/O strobe signal, active-low
DSP_IS
O/Z
DSP I/O space select, active-low
DSP_PS
O/Z
DSP program space select, active-low
DSP_READY
DSP_R/W
I
O/Z
VSS
CVDD
DSP data ready input (tie high if not used), active-high. If this signal is unused, it must be
pulled high with an external pullup resistor.
DSP active-high read / active-low write signal
Ground
1.8-V supply for core logic
DVDD
3.3-V supply for I/O cells
N/C
No Connection
† I = input, O = output, Z = high-impedance
‡ The KBGPIO[15:8] pins include integrated pullup resistors.
§ The ARM7TDMI core can operate in either little- or big-endian mode. The 5470 configures the ARM7TDMI core’s endianness by sampling this
pin at the RESET rising edge.
¶ 5470 only supports MCU boot from a 16-bit or a 32-bit-wide memory implementation on CS0. The 5470 configures the ARM7TDMI starting
instruction size, and width of memory connected to CS0, by sampling this pin at the RESET rising edge.
December 2001 – Revised December 2002
SPRS017B
9
Introduction
Table 2–3. Internal Pullup/Pulldown Terminal List
I/O
BALL #
DSP_D00
TERMINAL NAME
I/O/Z
C10
PS100, 100-µA pullup
DSP_D01
I/O/Z
F10
PS100, 100-µA pullup
DSP_D02
I/O/Z
A9
PS100, 100-µA pullup
DSP_D03
I/O/Z
B9
PS100, 100-µA pullup
DSP_D04
I/O/Z
F9
PS100, 100-µA pullup
DSP_D05
I/O/Z
E9
PS100, 100-µA pullup
DSP_D06
I/O/Z
A8
PS100, 100-µA pullup
DSP_D07
I/O/Z
B8
PS100, 100-µA pullup
DSP_D08
I/O/Z
F8
PS100, 100-µA pullup
DSP_D09
I/O/Z
E8
PS100, 100-µA pullup
DSP_D10
I/O/Z
A7
PS100, 100-µA pullup
DSP_D11
I/O/Z
B7
PS100, 100-µA pullup
DSP_D12
I/O/Z
F7
PS100, 100-µA pullup
DSP_D13
I/O/Z
A6
PS100, 100-µA pullup
DSP_D14
I/O/Z
B6
PS100, 100-µA pullup
DSP_D15
I/O/Z
C6
PS100, 100-µA pullup
KBGPIO08
I/O
M1
PS100, 100-µA pullup
KBGPIO09
I/O
M2
PS100, 100-µA pullup
KBGPIO10/DSP_IACK
I/O
L5
PS100, 100-µA pullup
KBGPIO11/DSP_IAQ
I/O
K2
PS100, 100-µA pullup
KBGPIO12/DSP_MSC
I/O
L6
PS100, 100-µA pullup
KBGPIO13/DSP_TOUT
I/O
K1
PS100, 100-µA pullup
KBGPIO14/DSP_CLKOUT
I/O
H1
PS100, 100-µA pullup
KBGPIO15/ARM_MCLK
I/O
L1
PS100, 100-µA pullup
GPIO16/SDA
I/O
G1
PS100, 100-µA pullup
CS4/BIGEND
I/O
W18
PE100, 100-µA pulldown
CS3/ROMSIZE16
I/O
J14
PS100, 100-µA pullup
EMU0
I/O
V10
PS100, 100-µA pullup
EMU1
I/O
V8
PS100, 100-µA pullup
I
W9
PE100, 100-µA pulldown
TCK
TYPE
TRST
I
W8
PE100, 100-µA pulldown
TMS
I/O
W10
PS100, 100-µA pullup
TDI
I/O
V9
PS100, 100-µA pullup
10
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
3
DSP Subsystem Functional Overview
The DSP subsystem is based on the TMS320C54x DSP core, on-chip memories and peripherals, and is
code-compatible with other C54x products. The following description of the 5470 DSP subsystem is based
on Figure 3–1.
DSP Subsystem
CODEC
McBSP
McBSP
DMA
TIMER
XIO
External
DSP
Memory
CODEC
8 K × 16
Data RAM
8 K × 16
Prog RAM
C54x DSP
8 K × 16
Prog RAM
8 K × 16
Data RAM
8 K × 16
Prog RAM
8 K × 16
Data RAM
8 K × 16
Data RAM
API
PLL
8 K × 16
Prog RAM
8 K × 16
Prog RAM
MCU Subsystem
Figure 3–1. 5470 DSP Subsystem Functional Block Diagram
3.1
DSP Core
The 5470 DSP subsystem’s fixed-point, digital signal processor (DSP) is based on an advanced modified
Harvard architecture that has one program memory bus and three data memory buses. This processor
provides an arithmetic logic unit (ALU) with a high degree of parallelism, application-specific hardware logic,
on-chip memory, and additional on-chip peripherals. The basis of the operational flexibility and speed of this
DSP is a highly specialized instruction set.
Separate program and data spaces allow simultaneous access to program instructions and data, providing
the high degree of parallelism. Two read operations and one write operation can be performed in a single cycle.
Instructions with parallel store and application-specific instructions can fully utilize this architecture. In
addition, data can be transferred between data and program spaces. Such parallelism supports a powerful
set of arithmetic, logic, and bit-manipulation operations that can all be performed in a single machine cycle.
In addition, the 5470 DSP subsystem includes the control mechanisms to manage repeated operations,
function calls, and DSP interrupts.
The DSP core includes the following features:
•
•
•
•
Low-power C54x DSP CPU, operating at up to 100 MHz
Software-programmable wait-state generator with bank-switching wait-state logic
External memory interface
– Program space
– Data space
– I/O space
Scan-based emulation logic
December 2001 – Revised December 2002
SPRS017B
11
DSP Subsystem Functional Overview
The 5470 DSP subsystem includes the DSP CPU core, a programmable phase-locked loop (PLL) for clock
generation, an interface to external parallel devices, a timer, 72K words of RAM, two multichannel buffered
serial interfaces, an interface to allow MCU access to part of the DSP subsystem memory map, and a JTAG
interface.
3.1.1 DSP Memory Space and Buses
The 5470 subsystem has multiple memory spaces and four parallel buses that allow you to access both
program and data simultaneously. Each of the four buses access different memory spaces for different
aspects of the DSP operation:
•
The DSP subsystem includes 72K words of on-chip RAM, as well as an extensive external memory range,
which can be used to interface to a variety of memory types or peripherals.
•
The program bus (PB) reads from program memory space, which contains the instructions to be
executed.
•
The write data bus (EB) writes into data memory space, which stores data used by the instructions and
tables eventually used in execution. It also writes into I/O memory space.
•
The two read data buses (CB and DB) read data from the data memory space and the DB data bus
accesses I/O memory space. The I/O memory space interfaces to external memory-mapped peripherals
and can serve as extra data storage space.
3.1.2 DSP Scan-Based Emulation Logic
The 5470 DSP subsystem includes a dedicated emulation port for in-circuit emulation. The emulation port is
accessed directly by the Texas Instruments (TI) extended development system (XDS) hardware emulator and
provides emulation.
3.2
DSP Memory
The 5470 device implements 72K words of on-chip RAM as follows:
•
•
•
40K words of program-space single-access RAM (SARAM)
16K words of data space dual-access RAM (DARAM)
16K words of data space single-access RAM (SARAM)
Each block of DARAM may perform up to two DSP accesses in one machine cycle. The DSP subsystem may
also perform multiple accesses to separate memory blocks in one machine cycle. After a “normal” reset, the
data-space RAM blocks in the addresses between 0x0000 and 0x7FFF are mapped into data memory space
only, and the program space RAM blocks between 0x06000 and 0x0FFFF are mapped only to program space.
The OVLY and DROM bits can affect this as shown in Figure 3–2 and Figure 3–3.
3.2.1 DSP On-Chip RAM
The DSP subsystem features 72K x 16-bit of on-chip RAM (two blocks of 8K x 16-bit DARAM and seven blocks
of 8K x 16-bit SARAM). The DSP CPU can perform two accesses to a DARAM in one machine cycle (two
reads in one cycle, or a read and a write in one cycle). It can also perform multiple accesses to separate
memory blocks in one machine cycle.
After reset, the lower address range of the program space is mapped to external memory, the lower address
range of the data space is mapped with on-chip RAM blocks. However, the OVLY bit in the PMST register
can be used to map these RAM blocks into both program and data space.
3.2.2 Normal Mode DSP Memory Map
The normal mode DSP subsystem provides the memory map shown in Figure 3–2. This is the memory map
that applies when the API boot mode feature is not enabled. The normal mode memory map applies any time
that DSP register BSCR[4] (ABMDIS) is 1, or when MCU register DSP_REG[9] (DSP_APIBN) is 1.
12
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
Hex
0000
Page 0 Program,
MP/MC = 1
(Microprocessor Mode)
OVLY = 1
OVLY = 0
Reserved
External
Program
Space
Memory
007F
0080
On-chip Data
DARAM
1FFF
2000
3FFF
4000
5FFF
6000
7FFF
External
Program
Space
Memory
On-chip Data
DARAM API
DARAM,
accessible
External
Program
Space
Memory
On-chip
On
chip Data
SARAM
External
Program
Space
Memory
External Program Space
Memory
8000
Hex
Page 0 Program,
MP/MC = 0
(Microcomputer Mode)
Hex
0000
OVLY = 1
OVLY = 0
0000
Reserved
External
Program
Space
Memory
007F
0080
On-chip Data
DARAM
1FFF
2000
3FFF
4000
5FFF
6000
7FFF
8000
9FFF
A000
External Program Space
Memory
y
BFFF
C000
DFFF
E000
FFFF
FFFF
External
Program
Space
Memory
On-chip Data
DARAM API
DARAM,
accessible
External
Program
Space
Memory
On chip Data
On-chip
SARAM
External
Program
Space
Memory
Data
Memory Mapped Registers,
Scratch-Pad RAM
007F
0080
On-chip Data DARAM
(8K–0x80 Words)
1FFF
2000
3FFF
4000
5FFF
On-chip Data DARAM,
API Accessible
(8K Words)
On-chip
On
chip Data SARAM
(8K Words)
6000
On-chip Program SARAM
(8K words,
words program only)
On-chip Program SARAM
(8K words, program only)
7FFF
On-chip Data SARAM,
(8K Words,
Words data only)
8000
External Data Space Memory
On-chip Program SARAM
(8K words, program only)
On-chip
On
chip Program SARAM
(8K Words)
On-chip
On
chip Program SARAM
(8K words)
BFFF
C000
FFFF
DROM=1
DROM=0
On-Chip
Program
SARAM
External
Data-space
Memory
Figure 3–2. Memory Map for DSP Accesses (DSP_APIBN = 1 or ABMDIS = 1)
3.2.3 API Boot Mode
Under normal DSP subsystem reset conditions, the DSP will begin operation either from code that has been
previously uploaded to internal program-space RAM (when in microcontroller mode) or from external memory
on the XIO bus (microprocessor mode). Uploading the code to internal program-space RAM may be
performed by the MCU. When the DSP subsystem is in API boot mode, the upper 2K words of the 8K-word
API SARAM is shadowed so that it is found both in DSP data space at 0x3800–0x3FFF and in DSP program
space at 0xF800 to 0xFFFF, which includes the DSP’s reset vector.
To make use of this mode, the MCU directly controls the DSP’s reset and API boot mode signals. It holds the
DSP in reset, enables API boot mode, and loads the DSP boot code via the API. Once it has loaded the code
to the appropriate location in the API SARAM, the MCU releases the DSP from reset, and the DSP begins
executing from the normal reset location, where the uploaded code now resides. Once the DSP code has
completed any API boot activity, it may disable the memory remapping provided by the API boot mode by
writing a 1 to BSCR[4] (ABMDIS). It is recommended that the MCU change the API boot mode input signal
only when the DSP is held in reset.
December 2001 – Revised December 2002
SPRS017B
13
DSP Subsystem Functional Overview
3.2.4 API Boot-Mode DSP Memory Map
The memory map when the API boot mode feature is enabled is shown in Figure 3–3. API boot mode is
enabled when DSP_REG[9] (DSP_APIBN) is 0 and BSCR[4] (ABMDIS) is 0.
Hex
0000
Page 0 Program,
MP/MC = 1
(Microprocessor Mode)
OVLY = 1
OVLY = 0
Reserved
External
Program
Space
007F
0080
1FFF
0000
OVLY = 1
OVLY = 0
0000
Reserved
External
Program
Space
007F
On-chip Data
DARAM,
API-accessible
External
Program
Space
3800
007F
On-chip Data DARAM
(8K–0x80 Words)
1FFF
2000
37FF
Data
Memory Mapped Registers,
Scratch-Pad RAM
0080
On-chip Data
DARAM
1FFF
2000
3800
Hex
0080
On-chip Data
DARAM
37FF
Hex
Page 0 Program,
MP/MC = 0
(Microcomputer Mode)
2000
On-chip Data
DARAM,
API-accessible
External
Program
g
Space
37FF
On-chip Data DARAM,
API-Accessible
(8K Words)
3800
(shadowed portion)
3FFF
4000
5FFF
3FFF
On chip Data
On-chip
SARAM
6000
4000
5FFF
3FFF
On chip Data
On-chip
SARAM
6000
4000
5FFF
6000
7FFF
On-chip
On
chip Data SARAM
(8K Words – data only)
On-chip
On
chip Data SARAM
(8K Words)
8000
External Data Space Memory
BFFF
External Program Space
C000
DROM=1
DFFF
On-chip
Program
SARAM
(8K Words)
External Program Space
E000
F7FF
F7FF
F800
F7FF
F800
Shadowed API DARAM (2K)
FFFF
External Data
Space
Memory
F800
Shadowed API DARAM (2K)
FFFF
On-chip
Program
SARAM
(6K Words)
DROM=0
External Data Space Memory
FFFF
† When DSP_REG[9] (DSP_APIBN) = 0 and BSCR[4] (ABMDIS) = 0, 2K words of the API DARAM are remapped to program-space, regardless of
DSP_REG[10] (MP/MC) value. All other internal program-space RAMs are disabled in program space. Overlayable data-space RAMs may be
dual-mapped to program-space via OVLY.
Figure 3–3. API Boot Mode Memory Map for DSP Accesses (DSP_APIBN = 0 and ABMDIS = 0)†
14
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
3.2.5 DSP Extended Program Memory
The DSP subsystem includes a memory paging scheme to extend the number of addressable program space
locations from 64K to 1M words. The four extended address pins (DSP_A16 to DSP_A19) are used to address
15 pages of program memory. Each page includes 64K addressable locations. The extended program
addresses are supported by eight instructions: FB[D], FBACC[D], FCALA[D], FCALL[D], FRET[D],
FRETE[D], READA, and WRITA.
•
•
•
•
•
•
•
•
FB[D] – Far branch
FBACC[D] – Far branch to the location specified by the value in accumulator A or accumulator B
FCALA[D] – Far call to the location specified by the value in accumulator A or accumulator B
FCALL[D] – Far call
FRET[D] – Far return
FRETE[D] – Far return with interrupts enabled
READA – Read program memory addressed by accumulator A and store in data memory
WRITA – Write data to program memory addressed by accumulator A
For more information on these instructions, please refer to the TMS320C54x DSP Reference Set, Volume 2:
Mnemonic Instruction Set (literature number SPRU172).
When the OVLY bit is set, each page of program memory is made up of two parts: a common block of
24K words maximum and a unique block of 40K words minimum. The common block is shared by all pages,
and each unique block is accessible only through its assigned page.
The value of the program counter extension register (XPC) defines the page selection. At a hardware reset,
the XPC is initialized to 0.
0 0000
1 0000
1 5FFF
Page 1
Lower 24K†
External
1 6000
Page
g 0
64K
0 FFFF
2 0000
2 5FFF
...
F 0000
...
F 5FFF
2 6000
Page 1
Upper 40K
External
1 FFFF
Page 2
Lower 24K†
External
Page 15
Lower 24K†
External
F 6000
Page 2
Upper 40K
External
...
Page 15
Upper 40K
External
...
2 FFFF
F FFFF
† Accesses to the lower 24K words of pages 1 through 15 are to external program memory only when the OVLY bit is cleared to 0. If the OVLY bit
is set to 1, on-chip RAM is mapped to 0x0 to 0x5FFF of pages 1 through 15. Note external address pins are provided to support 15 external pages.
Figure 3–4. DSP Extended Program Memory Map
3.2.6 DSP Relocatable Interrupt Vector Table
The reset, interrupt, and trap vectors are addressed in program space. These vectors are soft — meaning
that the processor, when taking the trap, loads the program counter (PC) with the trap address and executes
the code at the vector location. Four words are reserved at each vector location to accommodate a delayed
branch instruction, either two 1-word instructions or one 2-word instruction, which allows branching to the
appropriate interrupt service routine with minimal overhead.
December 2001 – Revised December 2002
SPRS017B
15
DSP Subsystem Functional Overview
At device reset, the reset, interrupt, and trap vectors are mapped to address FF80h in program space.
However, these vectors can be remapped to the beginning of any 128-word page in program space after
device reset. This is done by loading the interrupt vector pointer (IPTR) bits in the PMST register with the
appropriate 128-word page boundary address. After loading IPTR, any user interrupt or trap vector is mapped
to the new 128-word page.
NOTE: The hardware reset (RS) vector cannot be remapped because a hardware reset loads
the IPTR with 1s. Therefore, the reset vector is always fetched at location FF80h in program
space.
3.3
DSP Registers
The 5470 has 27 memory-mapped CPU registers, which are mapped in data memory space addresses 0h to
1Fh. Table 3–1 gives a list of CPU memory-mapped registers (MMRs) available on 5470. The device also has
a set of memory-mapped registers associated with peripherals as shown in Table 3–2.
Table 3–1. CPU Memory-Mapped Registers
ADDRESS
NAME
DESCRIPTION
DEC
HEX
IMR
0
0
Interrupt mask register
IFR
1
1
Interrupt flag register
Reserved for testing
–
2–5
2–5
ST0
6
6
Status register 0
ST1
7
7
Status register 1
AL
8
8
Accumulator A low word (15–0)
AH
9
9
Accumulator A high word (31–16)
AG
10
A
Accumulator A guard bits (39–32)
BL
11
B
Accumulator B low word (15–0)
BH
12
C
Accumulator B high word (31–16)
BG
13
D
Accumulator B guard bits (39–32)
TREG
14
E
Temporary register
TRN
15
F
Transition register
AR0
16
10
Auxiliary register 0
AR1
17
11
Auxiliary register 1
AR2
18
12
Auxiliary register 2
AR3
19
13
Auxiliary register 3
AR4
20
14
Auxiliary register 4
AR5
21
15
Auxiliary register 5
AR6
22
16
Auxiliary register 6
AR7
23
17
Auxiliary register 7
SP
24
18
Stack pointer register
BK
25
19
Circular buffer size register
BRC
26
1A
Block repeat counter
RSA
27
1B
Block repeat start address
REA
28
1C
Block repeat end address
PMST
29
1D
Processor mode status (PMST) register
XPC
30
1E
Extended program page register
–
31
1F
Reserved
16
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
This lists the 5470 DSP subsystem peripheral registers and describes those that are specific to the 5470 or
are different from the standard C54x registers. The standard C54x registers are defined in the
TMS320VC5409 Fixed-Point Digital Signal Processor data sheet (literature number SPRS082) and the
TMS320VC5402 Fixed-Point Digital Signal Processor data sheet (literature number SPRS079). The DSP
subsystem peripheral mapping is shown in Table 3–2.
Table 3–2. Peripheral Memory-Mapped Registers
NAME
ADDRESS
DESCRIPTION
TYPE
DRR20
20h
Data receive register 2
McBSP #0
DRR10
21h
Data receive register 1
McBSP #0
DXR20
22h
Data transmit register 2
McBSP #0
DXR10
23h
Data transmit register 1
McBSP #0
TIM
24h
Timer register
Timer
PRD
25h
Timer period counter
Timer
TCR
26h
Timer control register
Timer
–
27h
Reserved
SWWSR
28h
Software wait-state register
BSCR
29h
Bank-switching control register
–
2Ah
Reserved
2Bh
Software wait-state control register
SWCR
–
SPSA0
SPSD0
–
2Ch–37h
External Bus
External Bus, API
External Bus
Reserved
38h
McBSP0 subbank address register
McBSP #0
39h
McBSP0 subbank data register
McBSP #0
3Ah–3Bh
Reserved
GPIOCR
3C
General-purpose I/O pins control register
GPIO
GPIOSR
3D
General-purpose I/O pins status register
GPIO
–
3E–3F
Reserved
DRR21
40h
Data receive register 2
McBSP #1
DRR11
41h
Data receive register 1
McBSP #1
DXR21
42h
Data transmit register 2
McBSP #1
43h
Data transmit register 1
McBSP #1
DXR11
–
44h–47h
Reserved
SPSA1
48h
McBSP1 subbank address register
McBSP #1
SPSD1
49h
McBSP1 subbank data register
McBSP #1
–
4Ah–53h
Reserved
DMPREC
54h
DMA channel priority and enable control register
DMA
DMSA
55h
DMA subbank address register
DMA
DMSDI
56h
DMA subbank data register with autoincrement
DMA
DMSDN
57h
DMA subbank data register
DMA
CLKMD
58h
Clock mode register
PLL
–
59h–5Fh
December 2001 – Revised December 2002
Reserved
SPRS017B
17
DSP Subsystem Functional Overview
Table 3–3. McBSP Control Registers and Subaddresses
McBSP0
McBSP1
NAME
ADDRESS
SUB
ADDRESS
39h
SPCR11
49h
00h
Serial port control register 1
39h
SPCR21
49h
01h
Serial port control register 2
RCR10
39h
RCR11
49h
02h
Receive control register 1
RCR20
39h
RCR21
49h
03h
Receive control register 2
XCR10
39h
XCR11
49h
04h
Transmit control register 1
NAME
ADDRESS
SPCR10
SPCR20
DESCRIPTION
XCR20
39h
XCR21
49h
05h
Transmit control register 2
SRGR10
39h
SRGR11
49h
06h
Sample rate generator register 1
SRGR20
39h
SRGR21
49h
07h
Sample rate generator register 2
MCR10
39h
MCR11
49h
08h
Multichannel register 1
MCR20
39h
MCR21
49h
09h
Multichannel register 2
RCERA0
39h
RCERA1
49h
0Ah
Receive channel enable register partition A
RCERB0
39h
RCERB1
49h
0Bh
Receive channel enable register partition B
XCERA0
39h
XCERA1
49h
0Ch
Transmit channel enable register partition A
XCERB0
39h
XCERB1
49h
0Dh
Transmit channel enable register partition B
PCR0
39h
PCR1
49h
0Eh
Pin control register
3.3.1 Bank-Switching Control Register
The 5470 bank-switching control register (BSCR) controls both the bank-switching wait-state generation
functions that are consistent with the 5409, and several 5470-specific features. These special features include
control of configuration of some DSP subsystem external memory interface functionality and some aspects
of the interface whereby the MCU may access a portion of the DSP subsystem RAM. The BSCR is shown
in Figure 3–5 and the bits are described in Table 3–4.
The BSCR register also gives the DSP some control over the ARM programming interface, the mechanism
which enables the MCU to access portions of the DSPs internal RAM. Included are the API mode (APIMODE),
an interrupt to the MCU (HINT), and DSP memory map selection (ABMDIS).
15
12
11
10
5
4
3
2
1
0
BNKCMP
PS–DS
Reserved
ABM
DIS
HINT
API
MODE
Reserved
EXIO
R/W-1111
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
LEGEND: R = Read, W = Write
Figure 3–5. Bank-Switching Control Register (BSCR)
18
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
Table 3–4. Bank-Switching Control Register (BSCR) Bit Fields
NO.
BIT
NAME
RESET
VALUE
FUNCTION
15–12
BNKCMP
1111
Bank compare. Determines the external bank size. BNKCMP is used to mask the four MSBs of an address.
For example, if BNKCMP = 1111b, the four MSBs (bits 15–12) are compared, resulting in a bank size of
4K words. Bank sizes of 4K words to 64K words are allowed. Table 3–5 shows the relationship between
BNKCMP and the address range.
11
PS–DS
1
Program read – data read access. Inserts an extra cycle between consecutive accesses of program read
and data read, or data read and program read.
–
PS–DS = 0: No extra cycles are inserted by this feature
–
PS–DS = 1: One extra cycle is inserted between consecutive data and program reads.
10–5
Reserved
0
These bits are reserved and will retain written values.
4
ABMDIS
0
API boot mode disable. This bit will force the DSP out of API boot mode. This bit has no effect when the
DSP_APIBN is high. When DSP_APIBN is low, a 0 in this bit enables API boot mode and a 1 disables API
boot mode. Note that a DSP subsystem reset will clear this bit and thus re-enable the DSP_APIBN port.
3
2
HINT
APIMODE
0
0
–
ABMDIS = 0: API boot mode is under the control of DSP_APIBN
–
ABMDIS = 1: DSP_APIBN is ignored and DSP subsystem is kept out of API boot mode.
Host processor interrupt. This bit enables/disables an interrupt to the MCU from the DSP. At reset, the HINT
bit is cleared. To send a proper interrupt to the MCU, the DSP must write a 1 to HINT, delay an appropriate
time, then write a 0 to HINT to create a pulse of an appropriate duration on the interrupt signal to the MCU.
–
HINT = 0: Interrupt signal to the MCU is not active
–
HINT = 1: Interrupt signal to the MCU is active
HOM/SAM enable. This bit enables/disables the API host-only mode.
–
–
APIMODE = 0: The shared-access mode (SAM) is enabled. Both the DSP and the MCU may access
the API RAM.
APIMODE = 1: The host-only mode (HOM) is enabled. The MCU may access the API RAM; the DSP
may not access the API RAM. DSP writes to the API RAM are ignored, and DSP reads from the API
RAM return undefined values. DSP IDLE modes have no effect on MCU accesses to the API memory
when in host-only mode.
1
Reserved
0
These bits are reserved and will retain written values.
0
EXIO
0
External bus interface off. The EXIO bit controls the external bus-off function.
–
EXIO = 0: The external bus interface functions as usual.
–
EXIO = 1: The address bus, data bus, and control signals become inactive after completing the current
bus cycle. Table 3–6 lists the states of the external interface signals when the interface is disabled.
Note that the DROM, MP/MC, and OVLY bits in the PMST and the HM bit of ST1 cannot be modified
when the interface is disabled.
3.3.2 Programmable Bank-Switching Wait-States
The bank-switching features of the programmable bank-switching logic of the 5470 DSP subsystem is
functionally equivalent to that of the 5409. This feature automatically inserts one cycle when accessing across
memory-bank boundaries within program or data memory space. A bank-switching wait-state can also be
automatically inserted when accessing across the data space to program space boundary. These features
are programmed via the BNKCMP and PS–DS bits in the BSCR.
The relationship between BNKCMP, the address bits to be compared, and the bank size is summarized in
Table 3–5. The BNKCMP values that are not listed in the table are not allowed.
December 2001 – Revised December 2002
SPRS017B
19
DSP Subsystem Functional Overview
Table 3–5. Relationship Between BNKCMP and Bank Size
MSBs TO COMPARE
BANK SIZE
(16-BIT WORDS)
0
None
64K
0
15
32K
0
15–14
16K
1
0
15–13
8K
1
1
15–12
4K
BNKCMP
Bit 15
Bit 14
Bit 13
0
0
0
1
0
0
1
1
0
1
1
1
1
Bit 12
The external memory interface can be disabled when not used. This feature can be used to reduce the power
consumption of the 5470 DSP subsystem. Table 3–6 lists the states of the external interface pins, when the
interface is disabled (EXIO=1).
Table 3–6. State of Signals When External Bus Interface is Disabled (EXIO = 1)
SIGNAL
STATE
SIGNAL
STATE
DSP_A(19–0)
Previous State
DSP_MSTRB
High Level
DSP_D(15–0)
High Impedance
DSP_IOSTRB
High Level
DSP_PS
High Level
DSP_R/W
High Level
DSP_DS
High Level
KBGPIO12/DSP_MSC†
High Level
DSP_IS
High Level
KBGPIO11/DSP_IAQz‡
High Level
† Only applies when KBGPIO12 is enabled to output DSP_MSC.
‡ Only applies when KBGPIO11 is enabled to output DSP_IAQ
3.3.3 Processor Mode Status Register
The 5470 DSP subsystem processor mode status register (PMST) differs from the typical C54x design in that
the PMST CLKOUT bit has no effect on the CLKOUT port of the subsystem. This port is always clocking when
the DSP subsystem’s PLL is active.
20
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
3.4
DSP Peripherals
The following section describes how the 5470 DSP subsystem peripherals differ from standard peripherals
as found on the TMS320VC5409.
3.4.1 Multichannel Buffered Serial Port (McBSP)
The 5470 provides high-speed, full-duplex serial ports that are similar to those found on the 5409 device. They
allow direct interface to other 54x devices, codecs, and other devices in a system. There are two multichannel
buffered serial ports (McBSPs) within the DSP subsystem.
3.4.1.1
Deriving Sample Clock from an External Clock
To accommodate applications that require an external reference clock to be divided down to create the frame
sync clock and internal sample rate clock, the 5470 McBSP allows either the receive clock pin (BCLKR) or
the transmit clock pin (BCLKX) to be configured as the input clock to the sample rate generator. This
enhancement is enabled through two register bits: pin control register (PCR) bit 7 [enhanced sample clock
mode (SCLKME)] and sample rate generator register 2 (SRGR2) bit 13 [McBSP sample rate generator clock
mode (CLKSM)]. SCLKME is an addition to the PCR contained in the McBSPs on previous TMS320C5000
DSP platform devices. The new bit layout of the PCR is shown in Figure 3–6. For a description of the remaining
bits, see TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals (literature number SPRU302).
15
14
13
12
11
10
9
8
Reserved
XIOEN
RIOEN
FSXM
FSRM
CLKXM
CLKRM
RW
RW
RW
RW
RW
RW
RW
7
6
5
4
3
2
1
0
SCLKME
CLKS STAT
DX STAT
DR STAT
FSXP
FSRP
CLKXP
CLKRP
RW
RW
RW
RW
RW
RW
RW
RW
LEGEND: R = Read, W = Write
Figure 3–6. Pin Control Register (PCR)
The selection of the sample rate generator (SRG) clock input source is made by the combination of the
CLKSM and SCLKME bit values as shown in Table 3–7.
Table 3–7. Sample Rate Generator Clock Source Selection
SCLKME
CLKSM
SRG CLOCK SOURCE
0
0
Reserved
0
1
DSP_CPU clock
1
0
BCLKR pin
1
1
BCLKX pin
When either of the bidirectional pins, BCLKR or BCLKX, is configured as the clock input, its output buffer is
automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKR pin is configured as the
SRG input. In this case, both the transmitter and receiver circuits can be synchronized to the SRG output by
setting the PCR bits (9:8) for CLKXM = 1 and CLKRM = 1. However, the SRG output is only driven onto the
BCLKX pin since the BCLKR pin is used in input mode.
TMS320C5000 is a trademark of Texas Instruments.
December 2001 – Revised December 2002
SPRS017B
21
DSP Subsystem Functional Overview
3.4.2 DSP Direct Memory Access (DMA) Controller
The DSP subsystem includes a six-channel DMA controller, for performing data transfers independent of the
DSP. There are several limitations that the 5470 DMA controller places on its DMA transfers. The DMA
controller has no access to the RAMs that are normally in program space, cannot access RAMs that are
implemented in the MCU subsystem, and cannot access the RAM block in DSP data space that is connected
to the API interface. The DMA controller cannot transfer between the McBSP DRR and DXR registers, nor
can it transfer between McBSP DRR or DXR registers and external resources. The DMA controller cannot
perform 32-bit accesses to external resources.
3.4.2.1
DMA Controllers View of the DSP Memory Map
Note that the DMA controller has access only to the data space DARAM at 0x0080 to 0x1FFF and the data
space SARAMs that are at 0x4000 to 0x7FFF. It does not have access to any of the SARAMs in program
space between 0x6000 and 0xFFFF, or to the API DARAM at 0x2000 to 0x3FFF. The API module has access
to the 8K x 16 DARAM block at data space 0x2000 to 0x3FFF. Note also that the DMA controller can access
external data space devices with extended addressing, while the DSP can only access page 0 of external data
space.
3.4.2.2
DSP DMA External Access
The DMA supports external accesses to extended program space, extended data space, and extended I/O
space.
•
•
•
•
•
3.4.2.3
No more than one channel may be programmed for external writes at any time
No more than one channel may be programmed for external reads at any time
Only single-word transfers are supported for external accesses.
The DMA does not support transfers from peripherals to external memory.
The DMA does not support transfers from external memory to the peripherals.
DSP DMA Transfers in Doubleword Mode (Internal Only)
Doubleword mode allows the DMA to transfer 32-bit words in any index mode. In doubleword mode, two
consecutive 16-bit transfers are initiated and the source and destination addresses are automatically updated
following each transfer. In this mode, each 32-bit word is considered to be one element.
3.4.2.4
DSP DMA Interrupts
The ability of the DMA to interrupt the DSP based on the status of the data transfer is configurable and is
determined by the IMOD and DINM bits in the DMA channel mode control register (DMMCRn). The available
modes are shown in Table 3–8.
Table 3–8. DMA Interrupts
MODE
22
DINM
IMOD
ABU (non-decrement)
1
0
At full buffer only
ABU (non-decrement)
1
1
At half buffer and full buffer
Multi-Frame
1
0
At block transfer complete (DMCTRn = DMSEFCn[7:0] = 0)
Multi-Frame
1
1
At end of frame and end of block (DMCTRn = 0)
ABU or Multi-Frame
0
X
No interrupt generated
ABU or Multi-Frame
0
X
No interrupt generated
SPRS017B
INTERRUPT
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
3.4.2.5
DMA controller synchronization events
The internal transfers associated with each DMA channel can be synchronized to one of several events. The
DSYN bit field of the DMSEFCn register selects the synchronization event for a channel. The list of possible
events and the DSYN values are shown in Table 3–9.
Table 3–9. DMA Synchronization Events
DSYN VALUE
3.4.2.6
DMA SYNCHRONIZATION EVENT
0000b
No synchronization used
0001b
McBSP0 receive event
0010b
McBSP0 transmit event
0011b
Reserved
0100b
Reserved
0101b
McBSP1 receive event
0110b
McBSP1 transmit event
0111b
Reserved
1000b
Reserved
1001b
Reserved
1010b
Reserved
1011b
Reserved
1100b
Reserved
1101b
Timer interrupt event
1110b
External interrupt 0
1111b
Reserved
DSP DMA Channel Interrupt Selection
The DMA controller can generate a DSP interrupt for each of the six channels. However, due to a limit on the
number of internal DSP interrupt inputs, channels 0, 1, 2, and 3 are multiplexed with other interrupt sources.
DMA channels 0, 1, 2, and 3 share an interrupt line with the receive and transmit portions of the McBSP. When
the DSP is reset, the interrupts from these three DMA channels are deselected. The INTSEL bit field in the
DMPREC register can be used to select these interrupts, as shown in Table 3–10.
Table 3–10. DMA Channel Interrupt Selection
INTSEL Value
IMR/IFR[6]
IMR/IFR[7]
IMR/IFR[10]
IMR/IFR[11]
00b (reset)
Reserved
Reserved
BRINT1
BXINT1
01b
Reserved
Reserved
DMAC2
DMAC3
10b
DMAC0
DMAC1
DMAC2
DMAC3
11b
Reserved
3.4.3 ARM Port Interface (API)
Information is exchanged between the MCU and the DSP through the on-chip shared API memory. The API
memory is a 8K × 16-bit word DARAM (dual-access RAM) block. The API memory can also be used by the
DSP as general-purpose data or program DARAM. In this circuit, only the DSP memory has DARAM.
The API has two modes of operation selected by the bank switching control register (BSCR): shared-access
mode (SAM) and host-only mode (HOM). In SAM, both the DSP and the MCU can access the API memory.
In SAM, asynchronous host accesses from the MCU are resynchronized internally. If the DSP and the MCU
try to perform an access at the same time, the MCU has access priority and the DSP waits one cycle. SAM
can be run when the DSP is in IDLE1 mode. In HOM, only the MCU can access the API memory. When HOM
is selected, API memory blocks are disabled for DSP access, no value can be read from nor written to those
memory locations.
December 2001 – Revised December 2002
SPRS017B
23
DSP Subsystem Functional Overview
SAM is the default configuration when the DSP exits from a reset phase. SAM is normally selected whenever
the DSP is in normal operating mode or in IDLE 1. HOM is normally selected before the DSP is placed in IDLE2
or IDLE3.
3.4.4 DSP External Memory Interface
The 5470 external memory interface is largely identical to that of the 5409. Significant differences include the
lack of a MP/MC pin, and multiplexing of DSP_MSC, DSP_IAQ, DSP_IACK, and DSP_CLKOUT functions
on KBGPIO pins.
3.4.5 DSP Software-Programmable Wait-State Generator
The 5470 DSP subsystem’s software wait-state generator is compatible with the 5409. Wait-states
programmed in the SWWSR register apply to both DSP-generated and DMA-generated cycles to external
memory peripherals on the DSP’s XIO bus.
3.4.6 DSP Timer
The 5470 DSP timer is identical to that found on the 5409.
3.4.7 DSP Clocking
The DSP subsystem is capable of operating in DIV mode and PLL (normal) mode. The MCU may program
the initial DSP initial clocking mode, and DSP code may change to other clocking modes. The DSP controls
the clocking mode of operation via the settings in the CLKMD register.
The DSP subsystem’s PLL module, when operating in PLL (normal) mode, provides a multiplied version of
the REFCLK input clock as the DSP subsystem clock. The PLL can multiply by integer values between 1
and 15, by 0.5*n (for integer values of n between 1 and 15, inclusive), or by 0.25*n (for integer values of n
between 1 and 15, inclusive). To ensure that the PLL locks to the input frequency, the input clock frequency
must meet the minimum frequency as shown for each set of scaling values in Table 3–11.
24
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
Table 3–11. DSP Clock Scaler Values and Minimum REFCLK Frequencies
k (SCALER)
MINIMUM REFCLK
FREQUENCY (MHZ)
k = n, for integer values of n between 1 and 15, inclusive
5
k = 0.5 * n, for integer values of n between 1 and 15, inclusive
10
k = 0.25 * n, for integer values of n between 1 and 15, inclusive
20
When in DIV mode, the PLL minimum input frequencies do not apply.
The PLL_DSP output frequency is dynamically selected by the contents of the memory-mapped
DSP_CLKMD peripheral register. The initial settings for this register are controlled by a memory-mapped
register, DSP_REG, on the RISC processor. The PLL should not be programmed to exceed the DSP
subsystem’s maximum operating frequency as defined in the parametric portion of this data manual.
3.5
DSP Power Management
The DSP subsystem has three power-down modes, which are activated by the IDLE1, IDLE2, and IDLE3
instructions. In these modes, the C54x DSP core enters a dormant state and dissipates considerably less
power than in normal operation.
The IDLE1 mode halts all DSP activities except the DSP system clock. Because the system clock remains
applied to the DSP subsystem peripheral modules, the DSP peripheral circuits continue operating and the
DSP_CLKOUT pin remains active. Thus, peripherals such as serial ports and timers can take the DSP out
of its power-down state.
The IDLE2 mode halts the DSP subsystem peripherals as well as the DSP core, but the DSP subsystem’s
phase-locked loop clock multiplier will remain active to allow for a rapid resume from IDLE2. Because the DSP
subsystem peripherals are stopped in this mode, they cannot be used to generate the interrupt to wake up
the C54x as with IDLE1. However, power is significantly reduced because the device is completely stopped.
To terminate IDLE2, activate either RESET or DSP_INT0 with a pulse that meets the requirements defined
in the parametric section of this data manual. Note that RESET assertion will cause the MCU subsystem to
hold the DSP subsystem in reset.
The IDLE3 mode functions like IDLE2 but it also halts the DSP phase-locked loop (PLL) circuit. IDLE3 is used
to achieve the lowest possible DSP power consumption. This mode reduces power dissipation more than
IDLE2. Furthermore, the IDLE3 state allows you to reconfigure the DSP PLL externally if the system requires
the C54x to operate at a lower speed to save power. To terminate IDLE3, activate RESET or DSP_INT0 with
a pulse that meets the requirements defined in the parametric section of this data manual. Note that RESET
assertion will cause the MCU subsystem to hold the DSP subsystem in reset.
December 2001 – Revised December 2002
SPRS017B
25
DSP Subsystem Functional Overview
3.6
DSP Interrupts
The DSP subsystem interrupts are mapped as shown in Table 3–12.
Table 3–12. DSP Interrupt Mapping
ADDRESS
NAME
26
PRIORITY
FUNCTION
DEC
HEX
RS, SINTR
0
00
1
Reset
SINT16
4
04
2
Software interrupt #16
SINT17
8
08
—
Software interrupt #17
SINT18
12
0C
—
Software interrupt #18
SINT19
16
10
—
Software interrupt #19
SINT20
20
14
—
Software interrupt #20
SINT21
24
18
—
Software interrupt #21
SINT22
28
1C
—
Software interrupt #22
SINT23
32
20
—
Software interrupt #23
SINT24
36
24
—
Software interrupt #24
SINT25
40
28
—
Software interrupt #25
SINT26
44
2C
—
Software interrupt #26
SINT27
48
30
—
Software interrupt #27
SINT28
52
34
—
Software interrupt #28
SINT29
56
38
—
Software interrupt #29
SINT30
60
3C
—
Software interrupt #30
INT0, SINT0
64
40
3
External user interrupt 0
SINT1
68
44
4
Software interrupt #1
SINT2
72
48
5
Software interrupt #2
TINT, SINT3
76
4C
6
Timer interrupt
BRINT0, SINT4
80
50
7
McBSP #0 receive interrupt (default)
BXINT0, SINT5
84
54
8
McBSP #0 transmit interrupt (default)
DMAC0, SINT6
88
58
9
DMA channel 0, Software interrupt #6
DMAC1, SINT7
92
5C
10
DMA channel 1, Software interrupt #7
SINT8
96
60
11
Software interrupt #8
AINT, SINT9
100
64
12
API interrupt
BRINT1, DMAC2, SINT10
104
68
13
McBSP #1 receive interrupt (default)
BXINT1, DMAC3, SINT11
108
6C
14
McBSP #1 transmit interrupt (default)
DMAC4,SINT12
112
70
15
DMA channel 4 interrupt (default)
DMAC5,SINT13
116
74
16
DMA channel 5 interrupt (default)
–
120–127
78–7F
—
Reserved
SPRS017B
December 2001 – Revised December 2002
DSP Subsystem Functional Overview
The bits of the interrupt flag register (IFR) and interrupt mask register (IMR) are arranged as shown in
Figure 3–7. The function of each bit is described in Table 3–13.
15
14
Reserved
13
12
11
10
9
8
DMAC5
DMAC4
BXINT1/
DMAC3
BRINT1/
DMAC2
AINT
Reserved
2
1
0
7
6
5
4
3
DMAC1
DMAC0
BXINT0
BRINT0
TINT
Reserved
INT0
Figure 3–7. IFR and IMR Registers
Table 3–13. IFR and IMR Register Bit Fields
BIT
NUMBER
FUNCTION
NAME
15–14
–
13
DMAC5
DMA channel 5 interrupt flag/mask bit
12
DMAC4
DMA channel 4 interrupt flag/mask bit
11
BXINT1/DMAC3
McBSP1 transmit interrupt flag/mask bit
10
BRINT1/DMAC2
McBSP1 receive interrupt flag/mask bit
9
AINT
8
–
7
DMAC1
DMA channel 1 interrupt flag/mask bit
6
DMAC0
DMA channel 0 interrupt flag/mask bit
5
BXINT0
McBSP0 transmit interrupt flag/mask bit
4
BRINT0
McBSP0 receive interrupt flag/mask bit
3
TINT
2–1
–
0
INT0
December 2001 – Revised December 2002
Reserved
ARM-to-DSP interrupt flag/mask
Reserved
Timer interrupt flag/mask bit
Reserved
External interrupt 0 flag/mask bit
SPRS017B
27
MCU Subsystem Functional Overview
4
MCU Subsystem Functional Overview
The 5470 MCU subsystem includes TI’s emulation-enhanced ARM7TDMI microcontroller core and several
peripherals including SPI and I2C interfaces, UARTs, timers, general-purpose input/output, and external
memory interface. The MCU subsystem provides 4K x 32 bits of general-purpose RAM and 4K x 32 bits of
Ethernet packet RAM. The following description of the 5470 MCU subsystem is based on Figure 4–1.
4.1
MCU Core
The MCU subsystem uses Texas Instruments’ emulation-enhanced ARM71TDMIE core, a derivative of the
ARM Limited ARM7TDMI core. The ARM7TDMI processor core is a member of the ARM7 Thumb family.
It is a low power 32-bit RISC processor incorporating the Thumb 16-bit compressed instruction set. This
microprocessor executes 32-bit or 16-bit instructions and on 32-, 16-, or 8-bit data. The excellent code density
achieved with Thumb leads to system cost reductions by reducing the required memory size and achieving
32-bit system performance from 16-bit wide memories.
DSP Subsystem
MCU Subsystem
FLASH,
SDRAM,
etc.
Memory I/F
DSPSS
I/F
Clock
Oscillator
PLL
Clock
Manager
4K × 32
Packet RAM
I2C Device
GeneralPurpose
I/Os
RS232
Transceiver
UART/IRDA
IRDA
Transceiver
SPI
SPI Device
I2C
ARM7TDMIE
Keypad
UART
GPIO/Keypad
Watchdog
Timer
Timer
Interrupt
Handler
Figure 4–1. 5470 MCU Subsystem Functional Block Diagram
4.1.1 ARM7TDMI Emulation Features
The MCU subsystem’s ARM7TDMI core has been enhanced by TI with additional debugging features that
are available to emulation tools which understand TI’s ARM7TDMIE core. ARM7TDMI emulation tools which
are not specifically created with support for the ARM7TDMIE core’s emulation extensions are unable to take
advantage of these debugging features.
Thumb is a registered trademark of ARM Limited.
28
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
The enhanced emulation features provide the following debugging capabilities:
•
•
•
•
•
•
•
•
•
•
Single processor (MCU only) and multiprocessor (MCU and DSP) debug
High-level language and assembly debug (run, halt, step...)
Real-time (MCU continuously running) or non-real-time (MCU stopped) debug options
Supports both 32- and 16-bit ARM7TDMI modes
Endianess transparency
Unlimited breakpoints via opcode replacement (software breakpoint)
Two hardware breakpoints (one configurable as software breakpoint) with maskable cycle type, address
and data compare
Two external breakpoint events (EMU0, EMU1 pins)
Internal events generate external triggers
Benchmarking/profiling capability
4.1.2 MCU Memory Space
The MCU memory space includes internal RAM, internal peripherals, and areas for access to external
memories and peripherals connected to the CS0–CS3 and CS4 pins, and external SDRAM. The MCU
memory map is summarized in Table 4–1.
Table 4–1. MCU Memory Space
NAME
START ADDRESS
STOP ADDRESS
SIZE IN BYTES
DATA ACCESS
CS0
CS1
0000:0000
007F:FFFF
8M
8/16/32
0080:0000
00FF:FFFF
8M
8/16/32
CS2
0100:0000
017F:FFFF
8M
8/16/32
CS3
0180:0000
01FF:FFFF
8M
8/16/32
CS4
0200:0000
027F:FFFF
8M
8/16/32
0FFF:FFFF
32M
8/16/32
16K
8/16/32
16K
16/32
2
16
Reserved
0280:0000
SDRAM_CS
1000:0000
11FF:FFFF
Reserved
1200:0000
FFBF:FFFF
Internal SRAM
FFC0:0000
FFC0:3FFF
Reserved
FFC0:4000
FFDF:FFFF
API RAM
FFE0:0000
FFE0:3FFF
Reserved
FFE0:4000
FFF3:FFFF
API registers
FFE4:0000
FFE4:0001
Reserved
FFE4:0002
FFFF:07FF
UART_IRDA
FFFF:0800
FFFF:0FFF
2K
32
UART
FFFF:1000
FFFF:17FF
2K
32
I2C
FFFF:1800
FFFF:1FFF
2K
32
SPI
FFFF:2000
FFFF:27FF
2K
32
GPIO
FFFF:2800
FFFF:28FF
256
32
KGPIO
FFFF:2900
FFFF:29FF
256
32
Timer0
FFFF:2A00
FFFF:2AFF
256
32
Timer1
FFFF:2B00
FFFF:2BFF
256
32
Timer2
FFFF:2C00
FFFF:2CFF
256
32
INTH
FFFF:2D00
FFFF:2DFF
256
32
MEMINT
FFFF:2E00
FFFF:2EFF
256
32
CLKM
FFFF:2F00
FFFF:2FFF
256
32
SDRAMIF
FFFF:3000
FFFF:30FF
256
32
FFFF:31FF
256
32
Reserved
FFFF:3100
ARM_PLL
FFFF:3200
FFFF:32FF
Reserved
FFFF:3300
FFFF:FFFF
December 2001 – Revised December 2002
SPRS017B
29
MCU Subsystem Functional Overview
4.2
MCU Memory Interface
The MCU memory interface connects the MCU to the internal and external memories and peripherals via a
32-bit-wide data bus. This bus supports MCU access sizes of 8 bits, 16 bits, and 32 bits. All peripheral control
registers are implemented as 32-bit devices and should only be accessed using 32-bit operations.
The MCU memory interface allows endian configuration. Generally, a system should be configured so that
all peripherals operate in the same endian mode. In cases where mixed endianness is used, the software
engineer must carefully control accesses to resources which are configured for the endianness that is
opposite to that of the MCU.
The MCU memory interface also provides management of external accesses. External devices supported
include ROM (Flash), SRAM, and SDRAM. The external data bus is a 32-bit bidirectional bus. The following
access management features for MCU accesses to external memory and peripherals are provided:
•
•
•
•
Five external chip-select signals, each with a dedicated 8M-byte range of the MCU memory map.
MCU access duration management (wait-state insertion) to enable the connection of slow memory
devices, and support for intercycle delays to prevent external data bus contention.
MCU read and write access size adaptation for MCU accesses to external non-SDRAM memory or
peripherals with 32-bit, 16-bit, and 8-bit data bus width.
MCU read and write access size adaptation for MCU accesses to external SDRAM memory with 32-bit
or 16-bit data bus width.
The MCU memory ranges associated with each external memory chip-select (CS0–CS3, CS4) may be
configured in little-endian or big-endian mode. The MCU processor is also configured to operate in big/little
endian mode based on the state of “BIGEND” during power-up/reset time. MCU code that accesses a
resource that is configured with a different endianness than the MCU must perform the appropriate address
calculations (depending on the data size used to write the data, and the data size being used to read the data).
4.2.1 MCU Memory Interface Wait-States
MCU accesses to internal peripherals and internal memories are generally performed at 0 wait state. SDRAM
refresh cycles delay any MCU access. MCU accesses to the API RAM require multiple clocks as determined
by the programming of the API_REG register.
Timing for MCU accesses to external SDRAM memory is controlled by SDRAM interface registers which
control CAS latency, RAS latency, back-to-back timing, refresh rate, etc. External memories or peripherals
controlled by CS0–CS3 and CS4 may be programmed to provide various cycle timings. Additionally, the WAIT
input pin may be used to insert wait-states under external hardware control.
4.2.2 MCU API Interface
The API interface, which provides MCU access to a small portion of DSP memory, provides a 16-bit data path
to the API RAM in the DSP subsystem. All 32-bit transactions are divided into two 16-bit API transactions.
The API interface supports back-to-back access with programmable insertion of wait state to ensure correct
synchronization of signals between the MCU subsystem and the DSP subsystem.
30
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
4.2.3 MCU SDRAM Memory Interface
The SDRAM memory interface main features are:
•
•
•
•
•
•
•
It operates with the MCU memory interface (MEMINT) so that SDRAM memories can be used on the
same board with Flash and/or SRAM.
Supports 16- and 32-bit-wide data bus to SDRAM parts
Can address up to 256M bits of SDRAM
Operates at the MCU clock speed (47.5 MHz)
Flexible programming of SDRAM timing parameters
Supports four open SDRAM pages
Minimal burst operations supported. (In 16-bit-wide mode, a burst of two is supported.)
The SDRAM interface must be properly initialized before the SDRAM memory can be used. The following
steps are needed for initializing the SDRAM Interface:
•
•
•
•
Program SDRAM_REG for data bus size and the number of dummy cycles used after access to slower
memory device.
Program SDRAM parameters in SDRAM_CONFIG, SDRAM_REF_COUNT, and SDRAM_INIT_CONF
Write a ‘1’ in the INIT bit of the SDRAM_CNTL register
Wait until a ‘1’ is read inside the READY bit of the SDRAM_CNTL register before accessing the SDRAM.
NOTE: By writing a ‘1’ in the INIT bit of the SDRAM_CNTL register, the initialization state
machine of the SDRAM interface module will do the following: Wait for the number of cycles
that is programmed in INIT_NOP_MAX_CNT (should be 100 µs or greater). Send the
specified number of refresh commands that have been programmed into the
INIT_REF_MAX_CNT register.
The SDRAM load-mode-register command is used to configure the SDRAM device mode. Parameters used
in the load-mode-register command are based on the values programmed in the SDRAM interface registers.
December 2001 – Revised December 2002
SPRS017B
31
MCU Subsystem Functional Overview
4.3
MCU Peripherals
The following section describes the 5470 MCU subsystem peripherals.
4.3.1 MCU Universal Asynchronous Receiver/Transmitter (UART) Interfaces
The UART modules perform serial-to-parallel conversion on data characters received and parallel-to-serial
conversion on data characters transmitted by the processor.
4.3.1.1
UART Modes
UART mode supports data transmission and data reception via two 64-word-deep FIFOs. Five different parity
types are enabled, with three different stop bit formats. The word length is between 5 and 8, and line break
can be generated and detected. The baud rate is generated from the MCU subsystem clock by a
programmable divisor. All transmitting parameters can be detected in reception mode by an auto-bauding
mechanism that recognizes speed, word size, parity, and the number of stop bits. Software flow control is
available in the UART/IrDA when in UART mode. The UART/modem supports both software and hardware
flow control when in UART mode. Hardware flow control can reduce the MCU software overhead required
to process data interrupts.
UART/Modem Mode
The UART/modem provides an autobauding mechanism. All operations are controllable either via a software
interface or using hardware flow control signals.
The UART/Modem provides five external pin signals (multiplexed with GPIO pins):
•
•
•
•
•
GPIO09/TX_MODEM: Output - transmit data
GPIO10/RX_MODEM: Input - receive data
GPIO11/CTS_MODEM: Input - clear to send
GPIO12/RTS_MODEM: Output - request to send
GPIO13/DCD_MODEM: Output - data carrier detected
The UART/modem features:
•
•
•
•
•
Line-break generation and detection
Interrupt system control
Loop-back capabilities for internal test
The autobauding supports speeds between 1200 and 115.2 Kbits/s.
Hardware flow control (DCD, RTS, CTS)
UART/IrDA Mode
In the UART/IrDA mode, an Infrared Data Association (IrDA) protocol encoder/decoder manages the RXIR
and TXIR signals to an IrDA transceiver. It includes the slow infrared (SIR) protocol in order to be connected
with an infrared transmitter to any external data peripherals with an IrDA compliant data interface.
The UART/IrDA provides three external pin signals (multiplexed with GPIO pins):
•
•
•
32
GPIO07/TX_IRDA/TXIR_IRDA: Output – transmit data
GPIO08/RX_IRDA/RXIR_IRDA: Input – receive data
GPIO06/CLK16X_IRDA/SD_IRDA: Output – shut down the IR transceiver
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
UART/IrDA IrDA mode features:
•
IrDA 1.0 SIR support allows serial communication at baud rates up to 115.2 Kbits/s.
•
Sending a single infrared pulse signals a zero. A one is signaled by not sending any pulse. The width of
the pulse can be either 1.6 µs or 3/16th of a single bit time.
•
In IrDA 1.0 SIR mode, the device operation is similar to the operation in UART mode. However, the data
transfer operations are normally performed in half-duplex. The modem control and status signals are not
used.
Frame formatting: addition of variable xBOF characters and EOF characters
Uplink/downlink CRC generation/detection
Asynchronous transparency (automatic insertion of break character)
Eight characters status FIFO available to monitor frame length and frame errors
Variable frame length for RX and TX IrDA frame.
•
•
•
•
•
The format of the serial data is similar to the UART/modem data format. Each data word is sent with a zero
value start bit, followed by 8 data bits, and ending with at least one stop bit with a binary value of one.
In SIR mode, data transfer takes place between MCU and peripheral devices at speeds up to 115200 bits/s.
A SIR transmit frame consists of start flags (either a single C0h, multiple C0hs, or a single C0h preceded by
a number of FFh flags), followed by frame data supplied by the MCU, then a CRC-16 word, and a terminating
stop flag (C1h). The transmit state machine attaches start flags, CRC-16, and stop flags to the transmit data
provided by the MCU. If necessary, it also applies SIR data transparency.
NOTE: BLR[4] is used to select whether C0h or FFh start patterns are to be used when
multiple start flags are required.
SIR transparency is carried out if the outgoing data (between the start and stop flags) contains C0h, C1h,
or 7Dh. If one of these characters is about to be transmitted, then the SIR state machine sends an escape
character (7Dh) first, then inverts the fifth bit of the real data to be sent, and sends this data immediately after
the 7Dh character.
The SIR receiver state machine recovers the receive clock, removes the start flags, removes any
transparency from the incoming data, and determines frame boundary with reception of the stop flag. It also
checks for errors such as: frame abort (7Dh character followed immediately by a C1h stop flag, without
transparency), CRC error, and frame-length error. Once a frame is received, the state machine generates an
interrupt to the MCU. The MCU reads the LSR (status register) to check for receive errors, and processes
any valid receive data.
Note that the UART/IrDA is capable of operating in full-duplex, but that the SIR standard disallows full-duplex
operation.
The infrared output in SIR mode can implement either 1.6 µs or 3/16-bit encoding, which is selected by
ACREG[7]. In 1.6-µs encoding, the infrared pulse width is 1.6 µs. In 3/16-encoding, the infrared pulse width
is 3/16th of a bit duration (1/baud-rate).
4.3.1.2
FIFO Operation
The transmit FIFO is written via the THR register. Transmit FIFO status is reflected in the LSR.
The receive FIFO is read via the RHR register. The receive FIFO tracks reception of break, framing errors,
and parity errors on a byte-by-byte basis. The LSR bits which reflect receive status show the status for the
byte that is at the top of the FIFO. Reads of LSR do not advance the Receive FIFO pointer.
LSR[7] is set when there is an error anywhere in the RX FIFO and is cleared only when there are no more
errors remaining in the FIFO.
December 2001 – Revised December 2002
SPRS017B
33
MCU Subsystem Functional Overview
4.3.1.3
UART Clocking
The UART clock divisors must be set based on the MCU subsystem clock rate and the desired baud rate.
The UART_DIV_115K register is a prescaler which divides the MCU subsystem clock down to a rate usable
by the UART state machines. The UART_DIV_BITRATE register is the divider which provides the bit clock
to the UART from the pre-scaled clock.
UART_DIV_BITRATE = MCU clock frequency / UART_DIV_115K / desired bit rate
For autobaud function on the UART/modem, the UART_DIV_115K value must result in a 115200-Hz clock
rate:
UART_DIV_115K = MCU clock frequency / 115200 Hz.
4.3.2 MCU Serial Peripheral Interface (SPI)
The SPI is a bidirectional 3-line interface dedicated to the transfer of data to and from external devices offering
a 3-line serial interface.
The SPI interface is fully-duplexed and is configurable from 1 to 32 bits, providing three enable signals
programmable either as positive or negative edge- or level-sensitive.
This serial port is based on a looped shift-register which allows for both transmit (parallel-in, serial-out) and
receive (serial-in, parallel-out) modes. The serial port is fully controlled by the MCU memory interface (data
write, data read, and activation of serialization operations).
The serial clock period (TCLKX_SPI) is derived from the MCU subsystem clock, based on a prescale divider
(PTV):
SPI Clock Rate = MCU Clock Rate / (4 * PTV)
where PTV is 2, 4, 8, or 16.
4.3.3 MCU General-Purpose I/O
The 5470 provides 36 general-purpose I/Os (GPIOs) configurable in read or write mode by internal registers.
The GPIOs are divided into two groups, GPIO(19:0) and KBGPIO(15:0). KBGPIOs are keyboard GPIO pins,
which are implemented similarly to the GPIO(19:0) pins, although some KBGPIO pins have internal pullup
resistors. Some of the GPIO and KBGPIO pins share functionality with signals from other modules. Register
bits configure whether the pin is used for the normal GPIO or KBGPIO functionality, or for the alternate
functionality.
Each GPIO is associated with 6 configuration/status bits whose description is given in Table 4–2 and
Table 4–3.
34
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
Table 4–2. GPIO Control/Status Bits
BIT NAME
DESCRIPTION
io
I/O bit:
Writable when I/O is configured as an output (cio=0)
Reads value on I/O pin when I/O is configured as an input (cio=1)
cio
Configure I/O:
0: output
1: input (default)
gpio_irqA
See Table 4–3
gpio_irqB
See Table 4–3
ddio
gpio_en
Delta detect bit:
If gpio is configured as an output (cio=0), always reads as ‘0’
If gpio is configured as an input (cio=1), reads a ‘1’ if io has changed since ddio was last cleared
Selects register for muxed GPIOs:
0: other signal
1: gpio (default)
Non-shared GPIOs are always available at the i/o pin independent of the value of gpio_en
Table 4–3. GPIO_IRQ Bits Definition
gpio_irqB
gpio_irqA
FUNCTION
0
0
The associated device pin does not cause assertion of a GPIO interrupt.
0
1
A rising edge on the associated device pin causes assertion of a GPIO interrupt.
1
0
A falling edge on the associated device pin causes assertion of a GPIO interrupt.
1
1
Any change on the associated device pin causes assertion of a GPIO interrupt.
The configuration/status bits are accessible through 12 memory-mapped registers: GPIO_IO, KBGPIO_IO,
GPIO_CIO, KBGPIO_CIO, GPIO_IRQA, KBGPIO_IRQA, GPIO_IRQB, KBGPIO_IRQB, GPIO_DDIO,
KBGPIO_DDIO, GPIO_EN and KBGPIO_EN.
The pins KBGPIO(15:8) have on-chip pullup resistors, making them suitable for use as keypad row inputs.
To configure the 5470 for an 8x8 keypad [with keypad columns connected to KBGPIO(7:0) and rows
connected to KBGPIO(15:8)], use the following settings:
•
•
KBGPIO(15:8) pins are configured as inputs (cio=1) for row lines
KBGPIO(7:0) pins are configured as outputs (cio=0) for column lines
Keypad scanning can be done by setting the output values on all of the column KBGPIO pins to 0 and enabling
KBGPIO(15:8) interrupts. When a KBGPIO(15:8) interrupt is seen, all but one of the the KGBPIO column
output values are be changed to 1, and then the KBGPIO row pins are read. If the KBGPIO pin row input value
is all 1s, then there are no keys in the column currently driven to 0 that are set. Any bit in the KGBPIO pin
row input value that is 0 indicates a closed switch. Next, select a different column by writing a new value to
KBGPIO column pins with just one output pin value 0 and the remainder 1. Repeat the KBGPIO row read and
check for closed switches. Repeat this for each column in the keyboard array. Once the keypad has been read,
the interrupt service routine should set all column outputs back to 0 so that the next key press may be sensed.
December 2001 – Revised December 2002
SPRS017B
35
MCU Subsystem Functional Overview
4.3.4 MCU Inter-Integrated Circuit (I 2C) Interface
The master I2C interface module provides an interface between the MCU subsystem bus and the I2C pins,
allowing the MCU to control external peripheral devices connected to the I2C pins. Fundamentally, the I2C
interface module is a parallel-to-serial and serial-to-parallel converter. The parallel data received from the
MCU for transmit has to be converted to a suitable serial form for external peripheral devices on the I2C Bus.
Conversely, the serial data received from the I2C bus has to be converted to a suitable parallel form for passing
to the MCU.
The I2C interface features are:
•
•
•
•
•
•
•
•
Operates as an I2C master only; cannot be configured as an I2C slave
Supports 7-bit I2C device address
Supports an 8-bit I2C device subaddress
Master write to slave receiver in single or multiple mode (data loop)
Provides a 16-byte transmit FIFO to reduce MCU overhead
Supports simple read cycle, read combined cycle
A 3-bit programmable prescale internal clock divider and 7-bit programmable SCL clock divider to support
a wide range of input clock frequencies. The I2C SCL clock frequency are:
– I2C Standard Mode: 100 kHz
– I2C Fast Mode: 400 kHz
3-bit programmable spike filter to provide noise filtering on the I2C data input signal
The module does not support:
•
•
•
•
I2C bus 10-bit addressing
I2C bus CBUS compatibility
Multi-Master I2C
Clock synchronization as a handshake: slave devices are NOT allowed to hold the SCL line LOW to force
the master (5470) into a wait state until the slave is ready for the next transfer.
4.3.5 MCU Timers
The 5470 MCU subsystem implements three 16-bit timers configurable either in “auto reload” or in “count
down to zero and stop” modes. Each timer can generate an interrupt to the MCU when it counts down to zero.
The TIMER0 may be configured as either a watchdog counter or as a general-purpose timer. The two others
(TIMER1 and TIMER2) are general-purpose timers.
TIMER2 may be used to provide timing to an external device via the shared pin GPIO19/TIMER_OUT. When
this pin is configured to provide TIMER_OUT, the pin will provide a low pulse when the TIMER2 interrupt
occurs.
4.3.5.1
General-Purpose Timers
TIMER1 and TIMER2, are general-purpose timers, and can be programmed to provide specific timing via a
clock prescale value (PTV) and a starting count value (LOAD_TIM). The timer counts down to zero from the
LOAD_TIM value, changing value every n MCU subsystem clocks, depending on the PTV value. The time
between interrupts to the MCU interrupt handler is defined as:
tint = tclk * (LOAD_TIM + 1) * 2(PTV + 1)
If the counter’s auto-reload (AR) bit is set when the counter reaches zero, the timer will auto-reload the
LOAD_TIM value into its counter and start counting again.
The counter will only run when its start (ST) bit is set. The PTV and AR bits of the CNTL_TIMER register and
LOAD_TIM must not be programmed when the timer is running. The TIMERn current counter value may be
read via the VALUE_TIMn register.
I2C Bus is a trademark of Philips Electronics N. V. Corporation.
36
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
4.3.5.2
TIMER0 as a Watchdog Timer
By default, TIMER0 is configured as a watchdog timer. The watchdog is designed to detect user programs
stuck in infinite loops resulting in loss of program control or “runaway” programs. When configured as a
watchdog counter, TIMER0 will reset the MCU subsystem if it counts down to zero. The MCU’s reset
initialization code may examine the WATCHDOG_STAT register to determine if a MCU reset was caused by
the Watchdog.
The user program should write periodically into LOAD_TIM register before the counter reaches 0 in order to
reload the timer with this new value. A LOAD_TIM write is taken into account only if the new loaded value is
different from the previous one. When the watchdog counter reaches 0, it resets the MCU core and all the
MCU subsystem peripherals.
On power up, the watchdog is enabled and the value loaded into LOAD_TIM register is set to the maximum
value (0xFFFF) and PTV is set to seven. This gives to user a time of 16,777,216 * tclk to switch to normal timer
mode or to set a different watchdog timer time out to Timer0.
If a programmer does not want to have this default watchdog functionality, he must write a specific sequence
into a dedicated register (TIMER_MODE) in order to configure it as a general-purpose timer.
Disabling TIMER0 Watchdog Function
Timer0 may be configured as a general-purpose timer by writing a predefined sequence (0xF5 followed by
0xA0) in the WATCHDOG_DIS bits of the CNTL_TIMER0 register. If the watchdog disable function sees a
write to CNTL_TIMER0 with WATCHDOG_DIS set to 0xF5, it begins watching for another write to
CNTL_TIMER0 with WATCHDOG_DIS set to 0xA0. If WATCHDOG_DIS in the next write is 0xA0, TIMER0
is set for general-purpose mode. If the next write is instead 0xF5, TIMER0 remains in watchdog mode and
the disable function begins watching again for 0xF5.
Re-enabling TIMER0 Watchdog Function
To switch TIMER0 from general-purpose timer mode to watchdog timer mode, write a ‘1’ in the WATCHDOG
bit of the CNTL_TIMER0 register. When WATCHDOG is set to 1, the LOAD_TIM value is forced to 0xFFFF.
Due to internal sequencing, the MCU code should wait at least three timer clock periods before re-initializing
LOAD_TIM or PVT to values that meet system watchdog timing needs.
4.3.6 MCU Interrupt Handler
The MCU subsystem interrupt handler prioritizes and masks interrupts from up to 16 MCU subsystem
interrupt sources (IRQ0–15). It also steers these interrupts to the MCU’s two interrupt inputs: ARM_IRQ
(low-priority interrupt request) and ARM_FIQ (fast interrupt request). It receives interrupts from both internal
modules and the external chip environment. External interrupts to the MCU subsystem interrupt handler may
be provided through GPIO and/or KBGPIO pins.
Each interrupt source has an interrupt level register (ILR) which defines the priority of the corresponding
interrupt. When multiple interrupts are pending, the interrupt with the highest-priority interrupt level register
value is sent to the MCU first. In the case of multiple pending interrupts with identical ILR priority values (with
no other pending interrupts with higher priority), the highest interrupt number is sent to the MCU first.
Each interrupt source can be individually routed to one of the two input interrupt lines of the MCU, by properly
setting the FIQ bit in the interrupt’s ILR_IRQ_n register.
December 2001 – Revised December 2002
SPRS017B
37
MCU Subsystem Functional Overview
The following paragraph lists the typical IRQ sequence. The FIQ sequence is similar.
•
As the interrupt handler sees unmasked interrupt inputs go active, it sets the corresponding IT_REG bit.
•
At this time, there are three possible cases:
–
If the NEW_INT_AGR bit in the INT_CTRL_REG is set, a previous interrupt has not yet been
completely serviced, and the new interrupt cannot be sent to the MCU.
–
If NEW_INT_AGR is 0 and there is only one interrupt marked as active in the IT_REG, that interrupt
number is selected as the interrupt to be passed to the MCU. This selected interrupt number is stored
in SIR_IRQ_REG.
–
If NEW_INT_AGR is 0 and there are more than one interrupt marked as active in the IT_REG, the
interrupt handler selects the highest-priority interrupt based on ILR_IRQ_n register priority values
and, where priority values are identical, interrupt numbers. This selected interrupt number is stored in
SIR_IRQ_REG.
•
The interrupt is sent to the MCU via its IRQ port.
•
The MCU begins execution at the IRQ vector. MCU code reads SIR_IRQ_REG to determine which
interrupt source caused the interrupt. MCU code branches to the appropriate Interrupt Service Routine.
•
The MCU software must write a “1” to the INT_CTRL_REG register NEW_IRQ_AGR bit in order to reset
the IRQ output and SIR_IRQ_REG register. This enables the interrupt handler to send new interrupts to
the MCU via the IRQ signal.
MCU subsystem interrupt numbers are shown in Table 4–4.
Table 4–4. MCU Peripheral Interrupt Mapping
4.4
IRQ REQUEST
MCU INTERRUPT SOURCE
IRQ0
Watchdog TIMER0 interrupt
IRQ1
TIMER1 interrupt
IRQ2
TIMER2 interrupt
IRQ3
GPIO0 interrupt
IRQ4
Reserved
IRQ5
KBGPIO(7:0) interrupt
IRQ6
UART interrupts
IRQ7
UART_IRDA interrupt
IRQ8
KBGPIO(15:8) interrupt
IRQ9
GPIO03
IRQ10
IRQ11
GPIO02
2
I C interrupt
IRQ12
GPIO1 interrupt
IRQ13
SPI interrupt
IRQ14
GPIO(19:4) interrupt
IRQ15
API interrupt
MCU Power-Down Modes
The MCU can be shut down and awaken by setting the appropriate bit into the CLKM_REG and
WAKEUP_REG. It is the software’s responsibility to put the ARM_CLOCK in bypass or low-frequency mode
before the MCU is shut down. The MCU is woken by the first interrupt received from one of the peripherals.
The MCU subsystem peripherals can be individually shut down and awaken by setting the corresponding bits
in the CLKM_REG and WAKEUP_REG register. It is the software’s responsibility to power down or wake up
individual peripherals.
38
SPRS017B
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
4.5
MCU Peripheral Clock Management
The 5470 device is clocked by the external clock input, REFCLK. The 5470 REFCLK input does not provide
a clock oscillator, so it must be driven by a square-wave input signal that meets VIH and VIL requirements.
Both subsystems (DSP and MCU) derive their clocks from REFCLK using software-programmable PLLs.
Immediately following reset or power up, the contents of the respective CLKMD registers for both subsystems
depend on the status of the programmable internal ports on their respective PLLs. For the MCU subsystem,
these internal ports are hardwired so that the programmable capability of default mode is not available. For
the DSP subsystem, the programmable internal ports to the DSP PLL are connected to the output of a register
(DSP_REG) that is controlled by the RISC processor. This allows the DSP PLL default values to be
programmable under the control of the MCU subsystem. The clock management scheme is shown in
Figure 4–2.
AUDIO_CLK
÷ 2(N+1)
Shut-down
REFCLK
PLL_DSP
D=512
÷ D
DSP_clock
DSP
Select_ARM_clk
ARM_clock
ARM
PLL_ARM
IrDA _clock
Shut-down
Interrupts
from
peripherals
Asynchronous
wake-up
INTH
UART_clock
PowerDown
Module
UART
IrDA
UART
SPI_clock
SPI
I2C_clock
I2C
TIMER_clock
TIMER
GPIO_clock
GPIO
Figure 4–2. Clock Management Module
The MCU subsystem operates in one of three modes: PLL (normal) mode, DIV mode, or power-down mode.
In power-down mode, the input clock frequency is divided by a large value (512 – 1023). Configuring the
operation of the MCU subsystem clock module in power-down mode and using divisor values below 512 will
result in stopping the clock.
Similar to the DSP clock, the MCU subsystem clock is also derived from the scaled version of the input clock,
REFCLK. The PLL used by the RISC has the same look and feel as the DSP PLL. For this reason, the RISC
processor uses the same minimum input-clock-frequency restriction and scaling values as the DSP.
December 2001 – Revised December 2002
SPRS017B
39
MCU Subsystem Functional Overview
4.6
Initialization
The RESET input is the master reset that resets both the DSP and MCU subsystems. The RESET_OUT
signal can be used to reset external peripherals under control of the MCU. Table 4–5 describes how reset
events are propagated to the MCU subsystem, the DSP subsystem, and the RESET_OUT pin.
Table 4–5. Reset Management
MCU Reset
DSP Reset
External Reset
(RESET_OUT)
RESET
Yes
Yes
Yes
RST_CMD watchdog
Yes
No
No
DSP software reset (in register CLKM_CNTL_RST)
No
Yes
No
RESET_OUT (software controlled by bit in register
CLKM_CNTL_RST)
No
No
Yes
Activated Reset Signal
CLKM_CNTL_RST is a control register mapped in the MCU memory space at address 0xFFFF2F10.
When the MCU subsystem is reset, the MCU program counter begins execution at address 0x00000000.
When the DSP subsystem is reset, the DSP program counter begins execution from 0xFF80.
Each MCU subsystem peripheral may be independently held in reset via control bits in the MCU subsystem
register RESET_REG. By default, these bits are set as soon as the MCU subsystem reset is activated, which
leaves all MCU subsystem peripherals active.
4.6.1 Initial MCU Code
Since the MCU begins execution from address 0x00000000 after MCU subsystem reset, the initialization code
for the MCU subsystem must be provided by the memory device connected to the CS0 pin. This code may
be either 32-bit or 16-bit (Thumb) ARM code. The value of the CS3/ROMSIZE16 pin is sampled at the rising
edge of RESET to determine the mode that the ARM7TDMI core will execute.
CS3/ROMSIZE16 INPUT VALUE
AT RESET RISING EDGE
ARM7TDMI INITIAL MODE
0
16-bit instruction (Thumb) mode
1
32-bit instruction mode
Similarly, the MCU subsystem initializes the ARM7TDMI for big-endian or little-endian operation based on the
value sampled on the CS4_BIGEND pin at the rising edge of the RESET signal.
40
SPRS017B
CS4/BIGEND INPUT VALUE
AT RESET RISING EDGE
ARM7TDMI INITIAL MODE
0
Little-endian
1
Big-endian
December 2001 – Revised December 2002
MCU Subsystem Functional Overview
4.6.2 DSP Boot Mode
When the DSP comes out of reset, it begins execution from 0xFF80. It can execute code either from external
memory or from internal memory, depending on the value of the DSP_MPNMC bit in the MCU’s
DSP_PLL_REG register. Once the appropriate mode is set, and, if necessary, code is downloaded via the
API module, the MCU may release the DSP subsystem from reset by clearing the DSP_RESET bit in the MCU
subsystem’s CLKM_CNTL_RST register.
For the case where DSP execution starts from internal memory, the MCU should download the appropriate
DSP code via the API interface (before releasing the DSP from reset). This is done by properly setting the
DSP_MPNMC and DSP_APIBN bits in the DSP_PLL_REG MCU memory-mapped register, and then
downloading the code via the API interface. The DSP_APIBN bit, when 0, causes the 2K-word block of DSP
data memory at 0x3800–0x3FFF to appear also in DSP program space beginning at 0xF800.
Table 4–6 shows the combinations of the DSP_PLL_REG register DSP_MPNMC and DSP_APIBN bits that
control where the DSP fetches code immediately following release of DSP reset.
Table 4–6. DSP Boot Memory
DSP_MPNMC
DSP_APIBN
DSP BOOT MEMORY AT DSP PROGRAM SPACE ADDRESS 0xFF80
0
0
Shadow of the API-accessible on-chip data-space RAM
0
1
On-chip program-only RAM which is not accessible to the API module
1
0
Shadow of the API-accessible on-chip Data-space RAM
1
1
External DSP memory
4.6.3 Emulation Support
The 5470 provides flexible emulation capabilities. It supports both TI’s emulation tools and tools developed
by third parties.
Since the emulation tools may understand both the C54x DSP core and the ARM7TDMIE core, or just the
C54x DSP core, just the ARM7TDMIE core, or just the ARM7TDMI core, multiple emulation modes are
required. To allow configuration of the internal JTAG chains used by the various emulators, the 5470 samples
the EMU1 and EMU0 pins at TRST rising edge. Based on the values of these pins, the internal scan chain
is configured for different emulation modes. These modes are summarized in Table 4–7.
Table 4–7. Emulation Mode Selection
Values at TRST Rising Edge
SCAN CHAIN ORDER
EMU0
EMU1
0
0
Only the ARM7TDMIE core is in the chain. (This is also the mode for tools which only understand
the ARM7TDMI core.)
0
1
Only the C54x DSP core is in the chain
1
0
Reserved
1
1
ARM7TDMIE core followed by C54x DSP core followed by ASIC Logic test access port (TAP)
controller
December 2001 – Revised December 2002
SPRS017B
41
MCU Subsystem Functional Overview
Some tools that only understand one type of processor may be configured for use with 5470 even when other
devices are on the ASIC scan chain. This is done by instructing the tools to place the other “unrecognized”
devices on the JTAG scan chain in their “BYPASS” modes. While the exact configuration methods are beyond
the scope of this document, the key is to understand the length of the instruction registers for the TAP
controllers so that the correct BYPASS instructions can be issued. For the 5470, this methodology would only
apply to the 5470 emulation mode where all three TAP controllers are in the JTAG scan chain (EMU1 =
EMU0 = ’1’ at TRST rising edge). The JTAG TAP controller instruction register lengths are listed in Table 4–8.
Table 4–8. JTAG TAP Controller Instruction Register Lengths
INSTRUCTION REGISTER LENGTH
42
SPRS017B
JTAG TAP CONTROLLER
4 bits
ARM7TDMIE core
8 bits
C54x DSP core
8 bits
ASIC Logic TAP Controller
December 2001 – Revised December 2002
Documentation Support
5
Documentation Support
Extensive documentation supports all TMS320 DSP family of devices from product announcement through
applications development. The following types of documentation are available to support the design and use
of the C5000 platform of DSPs:
•
•
•
•
•
•
TMS320VC547x CPU and Peripherals Reference Guide (literature number SPRU038)
TMS320C54x DSP Functional Overview (literature number SPRU307)
Device-specific data sheets
Complete user’s guides
Development support tools
Hardware and software application reports
The five-volume TMS320C54x DSP Reference Set (literature number SPRU210) consists of:
•
•
•
•
•
Volume 1: CPU and Peripherals (literature number SPRU131)
Volume 2: Mnemonic Instruction Set (literature number SPRU172)
Volume 3: Algebraic Instruction Set (literature number SPRU179)
Volume 4: Applications Guide (literature number SPRU173)
Volume 5: Enhanced Peripherals (literature number SPRU302)
The reference set describes in detail the TMS320C54x DSP products currently available and the hardware
and software applications, including algorithms, for fixed-point TMS320 DSP family of devices.
A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal
processing research and education. The TMS320 DSP newsletter, Details on Signal Processing, is
published quarterly and distributed to update TMS320 DSP customers on product information.
Information regarding TI DSP products is also available on the Worldwide Web at http://www.ti.com uniform
resource locator (URL).
TMS320 and C5000 are trademarks of Texas Instruments.
December 2001 – Revised December 2002
SPRS017B
43
Electrical Specifications
6
Electrical Specifications
This section provides the absolute maximum ratings and the recommended operating conditions for the
device.
6.1
Absolute Maximum Ratings
The list of absolute maximum ratings are specified over operating case temperature. Stresses beyond those
listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated
under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions
for extended periods may affect device reliability. All supply voltage (core and I/O) values are with respect to
VSS.
Supply voltage I/O range, DVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4 V
Supply voltage core range, CVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 2 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.1 V
Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.1 V
Operating case temperature range, TC (Commercial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 85°C
TC (Industrial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
6.2
Recommended Operating Conditions
DVDD
Device supply voltage, I/O (Level shifter)†
CVDD
Device supply voltage, core†
VSS
Supply voltage, GND
VIH
High-level input voltage, I/O
VIL
Low-level input voltage
IOH
High-level output current
IOL
TC
Low-level output current
Operating case temperature
MIN
NOM
MAX
3
3.3
3.6
V
1.71
1.8
1.95
V
0
V
0.6*DVDD
V
0.3*DVDD
DSP_R/W, DSP_PS, DSP_IS, DSP_DS,
DSP_IOSTRB, DSP_MSTRB, DSP_A[19:0],
DSP_D[15:0], KBGPIO01/DSP_XF,
KBGPIO10/DSP_IACK,
KBGPIO14/DSP_CLKOUT
–8
All other outputs not including power/ground/DSP
signals.
–4
DSP_R/W, DSP_PS, DSP_IS, DSP_DS,
DSP_IOSTRB, DSP_MSTRB, DSP_A[19:0],
DSP_D[15:0], KBGPIO01/DSP_XF,
KBGPIO10/DSP_IACK,
KBGPIO14/DSP_CLKOUT
8
All other outputs not including power/ground/DSP
signals.
4
Commercial
Industrial
UNIT
0
85
–40
85
V
mA
mA
°C
† Texas Instrument DSPs do not require specific power sequencing between the core supply and the I/O supply. However, systems should be
designedto ensure that neither supply is powered up for extended periods of time if the other supply is below the proper operating voltage. Excessive
exposure to these conditions can adversely affect the long-term reliability of the devices. System-level concerns such as bus contention may require
supply sequencing to be implemented. In this case, the core supply should be powered up at the same time as or prior to the I/O buffers, and then
powered down after the I/O buffers.
44
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.3
Electrical Characteristics Over Recommended Operating Case Temperature
(Unless Otherwise Noted)
PARAMETER
VOH
VOL
IIZ
High-level output voltage
Low-level output voltage
Input current for
outputs in high
impedance
TEST CONDITIONS
IOH = RATED
IOL = RATED
Input
In
ut current
TYP
MAX
DVDD MAX, VI = VSS to DVDD
–300
0.22*DVDD
10
EMU[1:0], GPIO16/SDA,
CS3/ROMSIZE16,
KBGPIO12/DSP_MSC,
KBGPIO13/DSP_TOUT,
KBGPIO11/DSP_IAQ,
KBGPIO10/DSP_IACK,
KBGPIO14/DSP_CLKOUT,
KBGPIO15/ARM_MCLK,
KBGPIO[9:8], DSP_D[15:0],
DSP_A[19:0]
DVDD MAX, VI = VSS to DVDD
–10
310
All other inputs
DVDD MAX, VI = VSS to DVDD
–10
10
–10
310
–300
10
–10
10
TRST, TCK
DVDD MAX, VI = VSS to DVDD
All other input-only pins
IDDC
Supply current, core MCU (CVDD)
IDDP
Supply current, I/Os (DVDD)
CVDD MAX, DVDD MAX,
f(DSP_CLKOUT) = 100 MHz,
f(ARM_MCLK) = 47.5 MHz,
TC = 25 °C
CVDD MAX, DVDD MAX,
f(DSP_CLKOUT) = 100 MHz,
f(ARM_MCLK) = 47.5 MHz,
TC = 25 °C
UNIT
V
CS4/BIGEND
TDI, TMS
II
MIN
0.8*DVDD
V
µA
µA
70†
mA
50†
mA
Ci
Input capacitance
5
pF
Co
Output capacitance
5
pF
† Thecurrent measurements were taken with the following nominal conditions: CVDD = 1.8V, DVDD = 3.3V, temperature = 25C, with the DSP executing
program code from internal SRAM consisting of 50% NOP / 50% MACD instructions @ 100 MHz, and the ARM executing dhrystone program code
from external SRAM @ 47.5 MHz. Actual operating current varies with program being executed and external pin usage.
December 2001 – Revised December 2002
SPRS017B
45
Electrical Specifications
6.4
Package Thermal Resistance Characteristics
Table 6–1 provides the thermal resistance characteristics for the recommended package type used on the
TMS320VC5470 DSP.
Table 6–1. Thermal Resistance Characteristics
6.5
PARAMETER
GHK PACKAGE
UNIT
RΘJA
34
°C / W
RΘJC
9.5
°C / W
Timing Parameter Symbology
Timing parameter symbols used are created in accordance with JEDEC Standard 100. To shorten the
symbols, some of the pin names and other related terminology have been abbreviated as follows:
Lowercase subscripts and their meanings:
Letters and symbols and their meanings:
a
access time
H
c
cycle time (period)
L
Low
d
delay time
V
Valid
dis
disable time
Z
High impedance
en
enable time
f
fall time
h
hold time
r
rise time
su
setup time
t
transition time
v
valid time
w
pulse duration (width)
X
Unknown, changing, or don’t care level
High
The following load circuit in Figure 6–1 was used on all outputs pins and I/O pins in input mode. All timing
measurements in this data manual were measured from the 5470 connection to the following load circuit.
IOL
50 Ω
Tester Pin
Electronics
VLoad
CT
Output
Under
Test
IOH
Where: IOL
IOH
VLoad
CT
=
=
=
=
8 mA (all outputs)
8 mA (all outputs)
1.65 V
13-pF typical load circuit capacitance
Figure 6–1. 3.3-V Test Load Circuit
46
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.5.1 Divide-By-Two/Divide-By-Four Clock Option Timing
The frequency of the reference clock provided at the REFCLK pin can be divided by a factor of two or four
to generate the internal machine cycle. The selection of the clock mode is described in Section 3.4.7.
NOTE: The frequency injected must conform to specifications listed in Table 6–2.
Table 6–2 and Table 6–3 assume testing over recommended operating conditions and H = 0.5tc(CO)
(see Figure 6–2).
Table 6–2. Divide-By-Two/Divide-By-Four Clock Option Timing Requirements
MIN
MAX
20
†
ns
Fall time, REFCLK
8
ns
Rise time, REFCLK
8
ns
tc(CI)
tf(CI)
Cycle time, REFCLK
tr(CI)
tw(CIL)
Pulse duration, REFCLK low
5
UNIT
ns
tw(CIH) Pulse duration, REFCLK high
5
ns
† This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies approaching
0 Hz.
Unless otherwise noted, the same switching characteristics that apply to DSP_CLKOUT also apply to
ARM_MCLK.
Table 6–3. Divide-By-Two/Divide-By-Four Clock Option Switching Characteristics
PARAMETER
MIN
40
TYP
MAX
ns
17
ns
tc(CO)
td(CIH-CO)
Cycle time, DSP_CLKOUT
tf(CO)
tr(CO)
Fall time, DSP_CLKOUT
2
ns
Rise time, DSP_CLKOUT
2
ns
Delay time, REFCLK high to DSP_CLKOUT high/low
4
2tc(CI)
10
UNIT
†
tw(COL)
Pulse duration, DSP_CLKOUT low
H–2
H
H+2
ns
tw(COH)
Pulse duration, DSP_CLKOUT high
H–2
H
H+2
ns
† This device utilizes a fully static design and therefore can operate with tc(CI) approaching ∞. The device is characterized at frequencies approaching
0 Hz.
tr(CI)
tw(CIH)
tw(CIL)
tc(CI)
tf(CI)
REFCLK
tc(CO)
td(CIH-CO)
tw(COH)
tf(CO)
tr(CO)
tw(COL)
DSP_CLKOUT
Figure 6–2. External Divide-by-Two Clock Timing
December 2001 – Revised December 2002
SPRS017B
47
Electrical Specifications
6.5.2 Multiply-By-N Clock Option (PLL Enabled) Timing
The frequency of the reference clock provided at the REFCLK pin can be multiplied by a factor of N to generate
the internal machine cycle. The selection of the clock mode and the value of N is described in Section 3.4.7.
NOTE: The external frequency injected must conform to specifications listed in the
Table 6–4.
Table 6–4 and Table 6–5 assume testing over recommended operating conditions and H = 0.5tc(CO)
(see Figure 6–3).
Table 6–4. Multiply-By-N Timing Requirements
tc(CI)
Integer PLL multiplier N (N = 1–15)†
PLL multiplier N = x.5†
Cycle time, REFCLK
MIN
20‡
MAX
20‡
20‡
100
PLL multiplier N = x.25, x.75†
tf(CI)
tr(CI)
UNIT
200
ns
50
Fall time, REFCLK
8
ns
Rise time, REFCLK
8
ns
tw(CIL) Pulse duration, REFCLK low
5
ns
tw(CIH) Pulse duration, REFCLK high
5
ns
† N = Multiplication factor
‡ The multiplication factor and minimum REFCLK cycle time should be chosen such that the resulting DSP_CLKOUT cycle time is within the specified
range (tc(CO)). Minimum tC(CI) for the ARM CPU is 21 ns.
Unless otherwise noted, the same switching characteristics that apply to DSP_CLKOUT also apply to
ARM_MCLK.
Table 6–5. Multiply-By-N Switching Characteristics
PARAMETER
tc(CO)DSP Cycle time, DSP_CLKOUT
tc(CO)ARM Cycle time, ARM_MCLK
MIN
TYP
10
21
tc(CI)/N†
tc(CI)/N†
4
10
MAX
UNIT
ns
ns
td(CI-CO)
tf(CO)
Delay time, REFCLK high/low to DSP_CLKOUT high/low
tr(CO)
tw(COL)
Rise time, DSP_CLKOUT
Pulse duration, DSP_CLKOUT low
H–2
H
H+2
ns
tw(COH)
tp
Pulse duration, DSP_CLKOUT high
H–2
H
H+2
ns
30
ms
Fall time, DSP_CLKOUT
17
2
ns
ns
2
ns
Transitory phase, PLL lock up time
† N = Multiplication factor
tw(CIH)
tc(CI)
tw(CIL) tr(CI)
tf(CI)
REFCLK
td(CI-CO)
tc(CO)
tp
DSP_CLKOUT
tw(COH)
tf(CO)
tw(COL)
tr(CO)
Unstable
Figure 6–3. External Multiply-by-One Clock Timing
48
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.6
Memory and Parallel I/O Interface Timing
6.6.1 Memory Read
Table 6–6 and Table 6–7 assume testing over recommended operating conditions with DSP_MSTRB = 0 and
H = 0.5tc(CO) (see Figure 6–4).
Table 6–6. Memory Read Timing Requirements†
MIN
MAX
2H–15‡
2H–15‡
UNIT
ta(A)M
ta(MSTRBL)
Access time, read data access from address valid
tsu(D)R
th(D)R
Setup time, read data before DSP_CLKOUT low
4
ns
Hold time, read data after DSP_CLKOUT low
4
ns
th(A-D)R
Hold time, read data after address invalid
0
ns
0
ns
Access time, read data access from DSP_MSTRB low
th(D)MSTRBH Hold time, read data after DSP_MSTRB high
† Address, DSP_PS, and DSP_DS timings are all included in timings referenced as address.
‡ This access timing reflects a zero wait-state timing.
ns
ns
Table 6–7. Memory Read Switching Characteristics†
MIN
MAX
UNIT
td(CLKL-A)
td(CLKH-A)
Delay time, DSP_CLKOUT low to address valid§
PARAMETER
1.5
11.5
ns
Delay time, DSP_CLKOUT high (transition) to address valid¶
1.5
11.5
ns
td(CLKL-MSL)
td(CLKL-MSH)
Delay time, DSP_CLKOUT low to DSP_MSTRB low
1.5
11.5
ns
Delay time, DSP_CLKOUT low to DSP_MSTRB high
Hold time, address valid after DSP_CLKOUT low§
1.5
11.5
ns
1.5
11.5
ns
1.5
11.5
ns
th(CLKL-A)R
th(CLKH-A)R
Hold time, address valid after DSP_CLKOUT high¶
† Address, DSP_PS, and DSP_DS timings are all included in timings referenced as address.
§ In the case of a memory read preceded by a memory read
¶ In the case of a memory read preceded by a memory write
December 2001 – Revised December 2002
SPRS017B
49
Electrical Specifications
DSP_CLKOUT
td(CLKL-A)
th(CLKL-A)R
DSP_A[19:0]
th(A-D)R
tsu(D)R
ta(A)M
th(D)R
DSP_D[15:0]
th(D)MSTRBH
td(CLKL-MSL)
td(CLKL-MSH)
ta(MSTRBL)
DSP_MSTRB
DSP_R/W
DSP_PS, DSP_DS
Figure 6–4. Memory Read
50
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.6.2 Memory Write
Table 6–8 assumes testing over recommended operating conditions with DSP_MSTRB = 0 and H = 0.5tc(CO)
(see Figure 6–5).
Table 6–8. Memory Write Switching Characteristics†
PARAMETER
MIN
MAX
UNIT
td(CLKH-A)
td(CLKL-A)
Delay time, DSP_CLKOUT high to address valid‡
Delay time, DSP_CLKOUT low to address valid§
1.5
11.5
ns
1.5
11.5
ns
td(CLKL-MSL)
td(CLKL-D)W
Delay time, DSP_CLKOUT low to DSP_MSTRB low
1.5
11.5
ns
Delay time, DSP_CLKOUT low to data valid
1.5
11.5
ns
td(CLKL-MSH)
td(CLKH-RWL)
Delay time, DSP_CLKOUT low to DSP_MSTRB high
1.5
11.5
ns
Delay time, DSP_CLKOUT high to DSP_R/W low
1.5
11.5
ns
td(CLKH-RWH)
td(RWL-MSTRBL)
Delay time, DSP_CLKOUT high to DSP_R/W high
1.5
11.5
ns
H–3
H+3
ns
th(A)W
Hold time, address valid after DSP_CLKOUT high‡
1.5
11.5
ns
th(D)MSH
tw(SL)MS
Hold time, write data valid after DSP_MSTRB high
H–3
H+3§
ns
Pulse duration, DSP_MSTRB low
2H–3
ns
tsu(A)W
tsu(D)MSH
Setup time, address valid before DSP_MSTRB low
2H–3
ns
Setup time, write data valid before DSP_MSTRB high
2H–3 2H+3§
ns
H–3
ns
Delay time, DSP_R/W low to DSP_MSTRB low
ten(D–RWL)
Enable time, data bus driven after DSP_R/W low
tdis(RWH–D)
Disable time, DSP_R/W high to data bus high impedance
† Address, DSP_PS, and DSP_DS timings are all included in timings referenced as address.
‡ In the case of a memory write preceded by a memory write
§ In the case of a memory write preceded by an I/O cycle
December 2001 – Revised December 2002
2
SPRS017B
ns
51
Electrical Specifications
DSP_CLKOUT
td(CLKH-A)
td(CLKL-A)
th(A)W
DSP_A[19:0]
td(CLKL-D)W
th(D)MSH
tsu(D)MSH
DSP_D[15:0]
td(CLKL-MSL)
tsu(A)W
tdis(RWH-D)
td(CLKL-MSH)
DSP_MSTRB
td(CLKH-RWL)
ten(D-RWL)
td(CLKH-RWH)
tw(SL)MS
td(RWL-MSTRBL)
DSP_R/W
DSP_PS, DSP_DS
Figure 6–5. Memory Write
52
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.6.3 Parallel I/O Port Read Timing Requirements
Table 6–9 and Table 6–10 assume testing over recommended operating conditions with DSP_IOSTRB = 0
and H = 0.5tc(CO) (see Figure 6–6).
Table 6–9. Parallel I/O Port Read Timing Requirements†
MIN
MAX
UNIT
ta(A)IO
ta(ISTRBL)IO
Access time, read data access from address valid‡
3H–15
ns
Access time, read data access from DSP_IOSTRB low‡
2H–15
ns
tsu(D)IOR
th(D)IOR
Setup time, read data before DSP_CLKOUT high
4
ns
Hold time, read data after DSP_CLKOUT high
0
ns
th(ISTRBH-D)R
Hold time, read data after DSP_IOSTRB high
0
ns
† Address and DSP_IS timings are included in timings referenced as address.
‡ This access timing reflects a zero wait-state timing.
Table 6–10. Parallel I/O Port Read Switching Characteristics†
PARAMETER
MIN
MAX
UNIT
td(CLKL-A)
td(CLKH-ISTRBL)
Delay time, DSP_CLKOUT low to address valid
1.5
11.5
ns
Delay time, DSP_CLKOUT high to DSP_IOSTRB low
1.5
11.5
ns
td(CLKH-ISTRBH)
th(A)IOR
Delay time, DSP_CLKOUT high to DSP_IOSTRB high
1.5
11.5
ns
Hold time, address after DSP_CLKOUT low
1.5
11.5
ns
† Address and DSP_IS timings are included in timings referenced as address.
DSP_CLKOUT
th(A)IOR
td(CLKL-A)
DSP_A[19:0]
th(D)IOR
tsu(D)IOR
ta(A)IO
DSP_D[15:0]
th(ISTRBH-D)R
td(CLKH-ISTRBH)
ta(ISTRBL)IO
td(CLKH-ISTRBL)
DSP_IOSTRB
DSP_R/W
DSP_IS
Figure 6–6. Parallel I/O Port Read
December 2001 – Revised December 2002
SPRS017B
53
Electrical Specifications
6.6.4 Parallel I/O Port Write Switching Characteristics
Table 6–11 assumes testing over recommended operating conditions with DSP_IOSTRB = 0 and
H = 0.5tc(CO) (see Figure 6–7).
Table 6–11. Parallel I/O Port Write Switching Characteristics†
PARAMETER
MIN
MAX
UNIT
td(CLKL-A)
td(CLKH-ISTRBL)
Delay time, DSP_CLKOUT low to address valid
1.5
11.5
ns
Delay time, DSP_CLKOUT high to DSP_IOSTRB low
1.5
11.5
ns
td(CLKH-D)IOW
td(CLKH-ISTRBH)
Delay time, DSP_CLKOUT high to write data valid
1.5
11.5
ns
Delay time, DSP_CLKOUT high to DSP_IOSTRB high
1.5
11.5
ns
td(CLKL-RWL)
td(CLKL-RWH)
Delay time, DSP_CLKOUT low to DSP_R/W low
1.5
11.5
ns
Delay time, DSP_CLKOUT low to DSP_R/W high
1.5
11.5
ns
th(A)IOW
Hold time, address valid after DSP_CLKOUT low
1.5
11.5
ns
th(D)IOW
Hold time, write data after DSP_IOSTRB high
H–3
H+3
ns
tsu(D)DSP_IOSTRBH
Setup time, write data before DSP_IOSTRB high
H–3
H+3
ns
H–3
H+3
ns
tsu(A)DSP_IOSTRBL Setup time, address valid before DSP_IOSTRB low
† Address and DSP_IS timings are included in timings referenced as address.
DSP_CLKOUT
tsu(A)DSP_IOSTRBL
td(CLKL-A)
th(A)IOW
DSP_A[19:0]
td(CLKH-D)IOW
th(D)IOW
DSP_D[15:0]
td(CLKH-ISTRBL)
td(CLKH-ISTRBH)
tsu(D)DSP_IOSTRBH
DSP_IOSTRB
td(CLKL-RWL)
td(CLKL-RWH)
DSP_R/W
DSP_IS
Figure 6–7. Parallel I/O Port Write
54
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.7
Ready Timing for Externally Generated Wait-States
Table 6–12 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 6–8,
through Figure 6–11).
Table 6–12. Ready Timing For Externally Generated Wait-States Timing Requirements†
MIN
tsu(RDY)
th(RDY)
tv(RDY)MSTRB
th(RDY)MSTRB
tv(RDY)DSP_IOSTRB
th(RDY)DSP_IOSTRB
Setup time, DSP_READY before DSP_CLKOUT low
5
Hold time, DSP_READY after DSP_CLKOUT low
Valid time, DSP_READY after DSP_MSTRB low‡
3
Hold time, DSP_READY after DSP_MSTRB low‡
4H
MAX
ns
ns
4H–11
Valid time, DSP_READY after DSP_IOSTRB low‡
Hold time, DSP_READY after DSP_IOSTRB low‡
UNIT
ns
ns
5H–11
5H
ns
ns
tv(MSCL)
Valid time, DSP_MSC low after DSP_CLKOUT low
1.5
11.5
ns
tv(MSCH)
Valid time, DSP_MSC high after DSP_CLKOUT low
1.5
11.5
ns
† The hardware wait-states can be used only in conjunction with the software wait-states to extend the bus cycles. To generate wait-states using
DSP_READY, at least two software wait-states must be programmed.
‡ These timings are included for reference only. The critical timings for DSP_READY are those referenced to DSP_CLKOUT.
DSP_CLKOUT
DSP_A[19:0]
tsu(RDY)
th(RDY)
DSP_READY
tv(RDY)MSTRB
th(RDY)MSTRB
DSP_MSTRB
tv(MSCH)
tv(MSCL)
DSP_MSC
Wait-States
Generated Internally
Wait State
Generated by
DSP_READY
Figure 6–8. Memory Read With Externally Generated Wait-States
December 2001 – Revised December 2002
SPRS017B
55
Electrical Specifications
DSP_CLKOUT
DSP_A[19:0]
DSP_D[15:0]
th(RDY)
tsu(RDY)
DSP_READY
tv(RDY)MSTRB
th(RDY)MSTRB
DSP_MSTRB
tv(MSCH)
tv(MSCL)
DSP_MSC
Wait-States
Generated Internally
Wait State Generated
by DSP_READY
Figure 6–9. Memory Write With Externally Generated Wait-States
DSP_CLKOUT
DSP_A[19:0]
th(RDY)
tsu(RDY)
DSP_READY
tv(RDY)DSP_IOSTRB
th(RDY)DSP_IOSTRB
DSP_IOSTRB
tv(MSCH)
tv(MSCL)
DSP_MSC
Wait State Generated
by DSP_READY
Wait-States
Generated
Internally
Figure 6–10. I/O Read With Externally Generated Wait-States
56
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
DSP_CLKOUT
DSP_A[19:0]
DSP_D[15:0]
th(RDY)
tsu(RDY)
DSP_READY
tv(RDY)DSP_IOSTRB
th(RDY)DSP_IOSTRB
DSP_IOSTRB
tv(MSCH)
tv(MSCL)
DSP_MSC
Wait-States
Generated
Internally
Wait State Generated by
DSP_READY
Figure 6–11. I/O Write With Externally Generated Wait-States
December 2001 – Revised December 2002
SPRS017B
57
Electrical Specifications
6.8
Interrupt Timings
Table 6–13 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 6–12).
Table 6–13. Reset and Interrupt Timing Requirements
MIN
MAX
UNIT
tw(INTH)S
tw(INTL)S
Pulse duration, DSP_INT0 high (synchronous)
2H+1
ns
Pulse duration, DSP_INT0 low (synchronous)
2H+1
ns
tw(INTL)A
tw(INTL)WKP
Pulse duration, DSP_INT0 low (asynchronous)
4H
ns
Pulse duration, DSP_INT0 low for IDLE2/IDLE3 wakeup
10
ns
tsu(INT)
Setup time, DSP_INT0 before DSP_CLKOUT low†
8
10
ns
† The external interrupt is synchronized to the core CPU by way of a two-flip-flop synchronizer which samples these inputs with consecutive falling
edges of DSP_CLKOUT. The input to the interrupt pin is required to represent a 1-0-0 sequence at the timing that is corresponding to three
DSP_CLKOUT sampling sequences.
DSP_CLKOUT
tsu(INT)
tsu(INT)
th(INT)
DSP_INT0
tw(INTH)A
tw(INTL)A
Figure 6–12. Interrupt Timing
58
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.9
Instruction Acquisition (DSP_IAQ) and Interrupt Acknowledge (DSP_IACK)
Timings
Table 6–14 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 6–13).
Table 6–14. DSP_IAQ and DSP_IACK Switching Characteristics
PARAMETER
MIN
MAX
UNIT
td(CLKL-IAQL)
td(CLKL-IAQH)
Delay time, DSP_CLKOUT low to DSP_IAQ low
1.5
11.5
ns
Delay time, DSP_CLKOUT low to DSP_IAQ high
1.5
11.5
ns
td(A)IAQ
td(CLKL-IACKL)
Delay time, address valid to DSP_IAQ low
1
ns
Delay time, DSP_CLKOUT low to DSP_IACK low
1.5
11.5
ns
td(CLKL-IACKH)
td(A)IACK
Delay time , DSP_CLKOUT low to DSP_IACK high
1.5
11.5
ns
1
ns
th(A)IAQ
th(A)IACK
Hold time, DSP_IAQ high after address invalid
–2
ns
Hold time, DSP_IACK high after address invalid
–2
ns
tw(IAQL)
tw(IACKL)
Pulse duration, DSP_IAQ low
2H–3
ns
Pulse duration, DSP_IACK low
2H–3
ns
Delay time, address valid to DSP_IACK low
DSP_CLKOUT
DSP_A[19:0]
td(CLKL-IAQH)
th(A)IAQ
td(CLKL-IAQL)
td(A)IAQ
tw(IAQL)
DSP_IAQ
td(CLKL-IACKL)
td(CLKL-IACKH)
th(A)IACK
td(A)IACK
tw(IACKL)
DSP_IACK
DSP_MSTRB
Figure 6–13. DSP_IAQ and DSP_IACK Timings
December 2001 – Revised December 2002
SPRS017B
59
Electrical Specifications
6.10 External Flag (DSP_XF) and DSP_TOUT Timings
Table 6–15 assumes testing over recommended operating conditions and H = 0.5tc(CO) (see Figure 6–14 and
Figure 6–15).
Table 6–15. DSP_XF and DSP_TOUT Switching Characteristics
PARAMETER
MIN
TYP
MAX
UNIT
Delay time, DSP_CLKOUT low to DSP_XF high
1.5
11.5
Delay time, DSP_CLKOUT low to DSP_XF low
1.5
11.5
td(TOUTH)
td(TOUTL)
Delay time, DSP_CLKOUT low to DSP_TOUT high
1.5
11.5
ns
Delay time, DSP_CLKOUT low to DSP_TOUT low
1.5
11.5
ns
tw(TOUT)
Pulse duration, DSP_TOUT
2H+3
ns
td(XF)
2H–3
2H
ns
DSP_CLKOUT
td(XF)
DSP_XF
Figure 6–14. DSP_XF Timing
DSP_CLKOUT
td(TOUTH)
td(TOUTL)
DSP_TOUT
tw(TOUT)
Figure 6–15. DSP_TOUT Timing
60
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.11 Multichannel Buffered Serial Port (McBSP) Timings
6.11.1
McBSP Receive and Transmit Timings
Table 6–16 and Table 6–17 assume testing over recommended operating conditions and H = 0.5tc(CO) (see
Figure 6–16 and Figure 6–17).
NOTE: Polarity bits CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals
is inverted, then the timing references of that signal are also inverted.
Table 6–16. McBSP Receive and Transmit Timing Requirements
MIN
tc(BCKRX)
tw(BCKRX)
MAX
UNIT
Cycle time, BCLK_R/X
BCLK_R/X ext
4H
ns
Pulse duration, BCLK_R/X or BCLK_R/X high
BCLK_R/X ext
2H–1
ns
BCLKR int
0
BCLKR ext
7
BCLKR int
0
BCLKR ext
7
BCLKX int
0
BCLKX ext
7
BCLKR int
9
BCLKR ext
2
BCLKR int
9
BCLKR ext
2
BCLKX int
9
BCLKX ext
2
th(BCKRL-BFRH)
Hold time,
time external BFSR high after BCLKR low
th(BCKRL-BDRV)
Hold time,
time BDR valid after BCLKR low
th(BCKXL-BFXH)
Hold time,
time external BFSX high after BCLKX low
tsu(BFRH-BCKRL)
Setup time,
time external BFSR high before BCLKR low
tsu(BDRV-BCKRL)
Setup time,
time BDR valid before BCLKR low
tsu(BFXH-BCKXL)
Setup time,
time external BFSX high before BCLKX low
tr(BCKRX)
tf(BCKRX)
Rise time, BCLKR_R/X
BCLK_R/X ext
5
ns
Fall time, BCLKR_R/X
BCLK_R/X ext
5
ns
December 2001 – Revised December 2002
ns
ns
ns
ns
ns
ns
SPRS017B
61
Electrical Specifications
Table 6–17. McBSP Receive and Transmit Switching Characteristics
PARAMETER
MIN
MAX
4H
D–6†
C–6†
D+1†
C+1†
ns
ns
tc(BCKRX)
tw(BCKRXH)
Cycle time, BCLK_R/X
BCLK_R/X int
Pulse duration, BCLK_R/X high
BCLK_R/X int
tw(BCKRXL)
td(BCKRH-BFRV)
Pulse duration, BCLK_R/X low
BCLK_R/X int
Delay time, BCLKR high to internal BFSR valid
BCLKR int
–1
8
BCLKX int
1
9
BCLKX ext
4
15
BCLKX int
–1
8
BCLKX ext
4
16
Delay time, BCLKX high to BDX valid. This a
applies
lies to all bits exce
exceptt the first BCLKX int
bit transmitted.
BCLKX ext
0
7
4
16
td(BCKXH-BFXV)
Delay time,
time BCLKX high to internal BFSX valid
tdis(BCKXH-BDXHZ)
Disable time,
time BCLKX high to BDX high impedance following last data bit
td(BCKXH-BDXV)
Delay time, BCLKX high to BDX valid.‡§
BCLKX int
Only applies to first bit transmitted when in Data Delay 1 or 2
BCLKX ext
(XDATDLY=01b or 10b) modes
ten(BCKXH-BDX)
Enable time, BCLKX high to BDX driven.‡§
Only applies to first bit transmitted when Data
(XDATDLY=01b or 10b) modes
td(BFXH-BDXV)
Delay time, BFSX high to BDX valid.‡§
BFSX int
Only applies to first bit transmitted when Data Delay 0 (XDATDLY=00b)
(XDATDLY 00b)
BFSX ext
mode.
ten(BFXH-BDX)
Enable time, BFSX high to BDX driven.‡§
BFSX int
Only applies to first bit transmitted when in Data Delay 0 (XDATDLY=00b)
(XDATDLY 00b)
BFSX ext
mode
UNIT
ns
7
ns
ns
ns
ns
16
BCLKX int
–4
BCLKX ext
2
Delay 1 or 2
ns
3
ns
14
–1
ns
2
† T = BCLKR/X period = (1 + CLKGDV) * 2H
C = BCLKR/X low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even
D = BCLKR/X high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 + 1) * 2H when CLKGDV is even
‡ See the TMS320C54x DSP Reference Set, Volume 5: Enhanced Peripherals (literature number SPRU302) for a description of the data delay
features of the McBSP.
§ The transmit delay enable (DXENA) and A-bis mode (ABIS) features of the McBSP are not implemented on the TMS320VC5470.
62
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
tc(BCKRX)
tw(BCKRXH)
tr(BCKRX)
tw(BCKRXL)
BCLKR
td(BCKRH–BFRV)
tf(BCKRX)
td(BCKRH–BFRV)
BFSR (int)
tsu(BFRH–BCKRL)
th(BCKRL–BFRH)
BFSR (ext)
th(BCKRL–BDRV)
tsu(BDRV–BCKRL)
BDR
(RDATDLY=00b)
Bit (n–1)
(n–2)
tsu(BDRV–BCKRL)
(n–3)
(n–4)
th(BCKRL–BDRV)
BDR
(RDATDLY=01b)
Bit (n–1)
(n–2)
tsu(BDRV–BCKRL)
BDR
(RDATDLY=10b)
(n–3)
th(BCKRL–BDRV)
Bit (n–1)
(n–2)
Figure 6–16. McBSP Receive Timings
tc(BCKRX)
tw(BCKRXH)
tw(BCKRXL)
tr(BCKRX)
tf(BCKRX)
BCLKX
td(BCKXH–BFXV)
td(BCKXH–BFXV)
BFSX (int)
tsu(BFXH–BCKXL)
th(BCKXL–BFXH)
BFSX (ext)
ten(BFXH–BDX)
BDX
(XDATDLY=00b)
Bit 0
td(BFXH–BDXV)
Bit (n–1)
td(BCKXH–BDXV)
(n–2)
ten(BCKXH–BDX)
BDX
(XDATDLY=01b)
Bit (n–1)
Bit 0
(n–4)
td(BCKXH–BDXV)
(n–2)
(n–3)
td(BCKXH–BDXV)
tdis(BCKXH–BDXHZ)
BDX
(XDATDLY=10b)
(n–3)
ten(BCKXH–BDX)
Bit 0
Bit (n–1)
(n–2)
Figure 6–17. McBSP Transmit Timings
December 2001 – Revised December 2002
SPRS017B
63
Electrical Specifications
6.11.2
McBSP General-Purpose Timings
Table 6–18 and Table 6–19 assume testing over recommended operating conditions (see Figure 6–18).
Table 6–18. McBSP General-Purpose Timing Requirements
MIN
Setup time, BGPIOx input mode before DSP_CLKOUT high†
Hold time, BGPIOx input mode after DSP_CLKOUT high†
tsu(BGPIO-COH)
th(COH-BGPIO)
† BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input.
MAX
UNIT
9
ns
0
ns
Table 6–19. McBSP General-Purpose Switching Characteristics
PARAMETER
td(COH-BGPIO)
Delay time, DSP_CLKOUT high to BGPIOx output mode‡
‡ BGPIOx refers to BCLKRx, BFSRx, BCLKXx, BFSXx, or BDXx when configured as a general-purpose output.
NOTE: Only the DSP subsystem can access the McBSPs as GPIOs; they are not available to the ARM subsystem.
tsu(BGPIO-COH)
MIN
MAX
–10
10
UNIT
ns
td(COH-BGPIO)
DSP_CLKOUT
th(COH-BGPIO)
BGPIOx Input
Mode†
BGPIOx Output
Mode‡
† BGPIOx refers to BCLKRx, BFSRx, BDRx, BCLKXx, or BFSXx when configured as a general-purpose input.
‡ BGPIOx refers to BCLKRx, BFSRx, BCLKXx, BFSXx, or BDXx when configured as a general-purpose output.
Figure 6–18. McBSP General-Purpose I/O Timings
64
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.11.3
McBSP as SPI Master or Slave Timings
Low inactive state without delay; the McBSP transmits data on the rising edge of BCLKX and receives data
on the falling edge of BCLKR.
Table 6–20 and Table 6–21 assume testing over recommended operating conditions, CLKSTP = 10b,
CLKXP = 0, and H = 0.5tc(CO) (see Figure 6–19).
NOTE: For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting
CLKSM = CLKGDV = 1.
Table 6–20. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b and CLKXP = 0)
tsu(BDRV-BCKXL)
th(BCKXL-BDRV)
Setup time, BDR valid before BCLKX low
tsu(BFXL-BCKXH)
Setup time, BFSX low before BCLKX high
tc(BCKX)
Cycle time, BCLKX
MASTER
SLAVE
MIN
MIN
MAX
MAX
UNIT
12
– 12H
ns
0
12H + 5
ns
10
ns
12H
32H
ns
Hold time, BDR valid after BCLKX low
Table 6–21. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b and CLKXP = 0)
MASTER†
PARAMETER
MIN
th(BCKXL-BFXL)
td(BFXL-BCKXH)
Hold time, BFSX low after BCLKX low‡
Delay time, BFSX low to BCLKX high§
td(BCKXH-BDXV)
Delay time, BCLKX high to BDX valid
tdis(BCKXL-BDXHZ)
Disable time, BDX high impedance following last data bit from
BCLKX low
tdis(BFXH-BDXHZ)
Disable time, BDX high impedance following last data bit from BFSX
high
SLAVE
MAX
MIN
MAX
UNIT
T–6
T+6
ns
C–6
C+6
ns
–3
7
C–2
C+3
6H + 5
10H + 14
ns
ns
2H+ 3
6H + 17
ns
td(BFXL-BDXV)
Delay time, BFSX low to BDX valid
4H + 2
8H + 17
ns
† T = BCLKX period = (1 + CLKGDV) * 2H
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even
‡ FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX
and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
§ BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(BCLKX).
LSB
tsu(BFXL-BCKXH)
tc(BCKX)
MSB
BCLKX
th(BCKXL-BFXL)
td(BFXL-BCKXH)
BFSX
tdis(BFXH-BDXHZ)
tdis(BCKXL-BDXHZ)
BDX
Bit 0
td(BFXL-BDXV)
td(BCKXH-BDXV)
Bit(n-1)
tsu(BDRV-BCLXL)
BDR
Bit 0
(n-2)
(n-3)
(n-4)
th(BCKXL-BDRV)
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 6–19. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
December 2001 – Revised December 2002
SPRS017B
65
Electrical Specifications
Low inactive state with delay; the McBSP transmits data one-half cycle ahead of the rising edge of BCLKX
and receives data on the rising edge of BCLKR.
Table 6–22 and Table 6–23 assume testing over recommended operating conditions, CLKSTP = 11b,
CLKXP = 0, and H = 0.5tc(CO) (see Figure 6–20).
NOTE: For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting
CLKSM = CLKGDV = 1.
Table 6–22. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b and CLKXP = 0)
tsu(BDRV-BCKXL)
th(BCKXH-BDRV)
Setup time, BDR valid before BCLKX low
tsu(BFXL-BCKXH)
Setup time, BFSX low before BCLKX high
tc(BCKX)
Cycle time, BCLKX
MASTER
SLAVE
MIN
MIN
MAX
MAX
UNIT
12
– 12H
ns
0
12H + 5
ns
10
ns
12H
32H
ns
Hold time, BDR valid after BCLKX high
Table 6–23. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b and CLKXP = 0)
MASTER†
PARAMETER
SLAVE
MIN
MAX
T–6
T+6
MIN
MAX
UNIT
th(BCKXL-BFXL)
td(BFXL-BCKXH)
Hold time, BFSX low after BCLKX low‡
Delay time, BFSX low to BCLKX high§
C–6
C+6
td(BCKXL-BDXV)
Delay time, BCLKX low to BDX valid
–3
7
6H + 5
10H + 14
ns
tdis(BCKXL-BDXHZ)
Disable time, BDX high impedance following last data bit from
BCLKX low
–2
4
6H + 3
10H + 17
ns
ns
ns
td(BFXL-BDXV)
Delay time, BFSX low to BDX valid
C–6 C+6
4H – 2
8H + 17
ns
† T = BCLKX period = (1 + CLKGDV) * 2H
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even
D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 + 1) * 2H when CLKGDV is even
‡ FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX
and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
§ BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(BCLKX).
tsu(BFXL-BCKXH)
LSB
tc(BCKX)
MSB
BCLKX
td(BFXL-BCKXH)
th(BCKXL-BFXL)
BFSX
tdis(BCKXL-BDXHZ)
BDX
td(BCKXL-BDXV)
td(BFXL-BDXV)
Bit 0
Bit(n-1)
tsu(BDRV-BCKXL)
BDR
Bit 0
(n-2)
(n-3)
(n-4)
th(BCKXH-BDRV)
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 6–20. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
66
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
High inactive state without delay; the McBSP transmits data on the falling edge of BCLKX and receives data
on the rising edge of BCLKR.
Table 6–24 and Table 6–25 assume testing over recommended operating conditions, CLKSTP = 10b,
CLKXP = 1, and H = 0.5tc(CO) (see Figure 6–21).
NOTE: For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting
CLKSM = CLKGDV = 1.
Table 6–24. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b and CLKXP = 1)
tsu(BDRV-BCKXH)
th(BCKXH-BDRV)
Setup time, BDR valid before BCLKX high
tsu(BFXL-BCKXL)
Setup time, BFSX low before BCLKX low
tc(BCKX)
Cycle time, BCLKX
MASTER
SLAVE
MIN
MIN
MAX
MAX
UNIT
12
– 12H
ns
0
12H + 5
ns
10
ns
12H
32H
ns
Hold time, BDR valid after BCLKX high
Table 6–25. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b and CLKXP = 1)
MASTER†
PARAMETER
SLAVE
MIN
MAX
T–6
T+6
C–6
C+6
–3
7
D–2
D+3
MIN
MAX
UNIT
th(BCKXH-BFXL)
td(BFXL-BCKXL)
Hold time, BFSX low after BCLKX high‡
Delay time, BFSX low to BCLKX low§
td(BCKXL-BDXV)
Delay time, BCLKX low to BDX valid
tdis(BCKXH-BDXHZ)
Disable time, BDX high impedance following last data bit from
BCLKX high
tdis(BFXH-BDXHZ)
Disable time, BDX high impedance following last data bit from BFSX
high
2H + 3
6H + 17
ns
td(BFXL-BDXV)
Delay time, BFSX low to BDX valid
4H – 2
8H + 17
ns
ns
ns
6H + 5
10H + 14
ns
ns
† T = BCLKX period = (1 + CLKGDV) * 2H
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even
‡ FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX
and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
§ BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(BCLKX).
tsu(BFXL-BCKXL)
LSB
tc(BCKX)
MSB
BCLKX
th(BCKXH-BFXL)
td(BFXL-BCKXL)
BFSX
tdis(BFXH-BDXHZ)
td(BFXL-BDXV)
td(BCKXL-BDXV)
tdis(BCKXH-BDXHZ)
BDX
Bit 0
Bit(n-1)
tsu(BDRV-BCKXH)
BDR
Bit 0
(n-2)
(n-3)
(n-4)
th(BCKXH-BDRV)
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 6–21. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
December 2001 – Revised December 2002
SPRS017B
67
Electrical Specifications
High inactive state with delay; the McBSP transmits data one-half cycle ahead of the falling edge of BCLKX
and receives data on the falling edge of BCLKR.
Table 6–26 and Table 6–27 assume testing over recommended operating conditions, CLKSTP = 11b,
CLKXP = 1, and H = 0.5tc(CO) (see Figure 6–22).
NOTE: For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting
CLKSM = CLKGDV = 1.
Table 6–26. McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b and CLKXP = 1)
tsu(BDRV-BCKXL)
th(BCKXL-BDRV)
Setup time, BDR valid before BCLKX low
tsu(BFXL-BCKXL)
Setup time, BFSX low before BCLKX low
tc(BCKX)
Cycle time, BCLKX
MASTER
SLAVE
MIN
MIN
MAX
UNIT
MAX
12
– 12H
ns
0
12H + 5
ns
10
ns
12H
32H
ns
Hold time, BDR valid after BCLKX low
Table 6–27. McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b and CLKXP = 1)
MASTER†
PARAMETER
SLAVE
MIN
MAX
T–6
T+6
MIN
UNIT
MAX
th(BCKXH-BFXL)
td(BFXL-BCKXL)
Hold time, BFSX low after BCLKX high‡
Delay time, BFSX low to BCLKX low§
C–6
C+6
td(BCKXH-BDXV)
Delay time, BCLKX high to BDX valid
–3
7
6H + 5
10H + 14
ns
tdis(BCKXH-BDXHZ)
Disable time, BDX high impedance following last data bit from
BCLKX high
–2
4
6H + 3
10H + 17
ns
ns
ns
td(BFXL-BDXV)
Delay time, BFSX low to BDX valid
C–6 C+6
4H – 2
8H + 17
ns
† T = BCLKX period = (1 + CLKGDV) * 2H
C = BCLKX low pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2) * 2H when CLKGDV is even
D = BCLKX high pulse width = T/2 when CLKGDV is odd or zero and = (CLKGDV/2 + 1) * 2H when CLKGDV is even
‡ FSRP = FSXP = 1. As a SPI master, BFSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on BFSX
and BFSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
§ BFSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(BCLKX).
LSB
tsu(BFXL-BCKXL)
tc(BCKX)
MSB
BCLKX
th(BCKXH-BFXL)
td(BFXL-BCKXL)
BFSX
tdis(BCKXH-BDXHZ)
Bit 0
BDX
td(BCKXH-BDXV)
td(BFXL-BDXV)
Bit(n-1)
tsu(BDRV-BCKXL)
BDR
Bit 0
(n-2)
(n-3)
(n-4)
th(BCKXL-BDRV)
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 6–22. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
68
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.12 Synchronous DRAM Timings
Table 6–28 and Table 6–29 assume testing over recommended operating conditions (see Figure 6–23
through Figure 6–29).
Table 6–28. Synchronous DRAM Timing Requirements
NO.
6
7
MIN
tsu(DV-SCLKH)
th(SCLKH-DV)
Setup time, read data valid before SDRAM_CLK high
Hold time, read data valid after SDRAM_CLK high
MAX
UNIT
4.5
ns
2
ns
Table 6–29. Synchronous DRAM Switching Characteristics
NO.
1
2
3
4
5
8
9
10
11
12
PARAMETER
MIN
MAX
UNIT
td(SCLKH-CSV)
td(SCLKH-DQMV)
Delay time, SDRAM_CLK high to chip select valid
0.5
11
ns
Delay time, SDRAM_CLK high to byte enable valid
0.5
11
ns
td(SCLKH-DQMIV)
td(SCLKH-AV)
Delay time, SDRAM_CLK high to byte enable invalid
0.5
11
ns
Delay time, SDRAM_CLK high to address valid
0.5
11
ns
td(SCLKH-AIV)
td(SCLKH-CASV)
Delay time, SDRAM_CLK high to address invalid
0.5
11
ns
Delay time, SDRAM_CLK high to SDRAM_CAS valid
0.5
11
ns
td(SCLKH-DV)
td(SCLKH-DIV)
Delay time, SDRAM_CLK high to data valid
0.5
11
ns
Delay time, SDRAM_CLK high to data invalid
0.5
11
ns
td(SCLKH-WEV)
td(SCLKH-RASV)
Delay time, SDRAM_CLK high to SDRAM_WE valid
0.5
11
ns
Delay time, SDRAM_CLK high to, SDRAM_RAS valid
0.5
11
ns
READ
SDRAM_CLK
1
CSn
2
BE1
SDRAM_DQM[3:0]
4
Bank
5
SDRAM_A[R:0]†
4
Column
5
SDRAM_A[C:0]†
4
3
BE2
BE3
BE4
5
SDRAM_A[10]†
6
DATA[31:00]
D1
7
D2
D3
D4
SDRAM_RAS
8
8
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–23. SDRAM Read Command (CAS Latency 3)
December 2001 – Revised December 2002
SPRS017B
69
Electrical Specifications
WRITE
SDRAM_CLK
1
1
CSn
2
3
3
SDRAM_DQM[3:0]
BE1
4
BE2
BE3
BE4
D2
D3
D4
5
SDRAM_A[R:0]†
Bank
4
SDRAM_A[C:0]†
5
Column
4
5
SDRAM_A[10]†
9
DATA[31:00]
9
D1
10
SDRAM_RAS
8
8
11
11
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–24. SDRAM Write Command
ACTIVE
SDRAM_CLK
1
1
CSn
SDRAM_DQM[3:0]
4
Bank Activate
5
SDRAM_A[R:0]†
4
Row Address
5
SDRAM_A[C:0]†
4
Row Address
5
SDRAM_A[R]†
DATA[31:00]
12
12
SDRAM_RAS
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–25. SDRAM Active Command
70
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
PRECHARGE
SDRAM_CLK
1
1
12
12
11
11
CSn
SDRAM_DQM[3:0]
SDRAM_A[R:0]†
DATA[31:00]
SDRAM_RAS
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–26. SDRAM Precharge Command
DEACTIVATE
SDRAM_CLK
1
1
CSn
SDRAM_DQM[3:0]
4
SDRAM_A[R:0]†
5
Bank
SDRAM_A[C:0]†
4
5
12
12
11
11
SDRAM_A[R]†
DATA[31:00]
SDRAM_RAS
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–27. SDRAM Deactivate Command
December 2001 – Revised December 2002
SPRS017B
71
Electrical Specifications
REFR
SDRAM_CLK
1
1
12
12
8
8
CSn
SDRAM_A[R:0]†
SDRAM_A[C:0]†
SDRAM_A[R]†
DATA[31:00]
SDRAM_RAS
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–28. SDRAM Refresh Command
MODE REGISTER SET
SDRAM_CLK
1
1
4
MRS value
5
12
12
8
8
11
11
CSn
SDRAM_DQM[3:0]
SDRAM_A[R:0]†
SDRAM_A[C:0]†
SDRAM_RAS
SDRAM_CAS
SDRAM_WE
† The values for R and C depend on the particular size of the SRAMs used.
Figure 6–29. SDRAM Mode Register Set Command
72
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.13 I2C Bus Timings
Table 6–30 through Table 6–32 assume testing over recommended operating conditions (see Figure 6–30
through Figure 6–32).
Table 6–30. I2C Bus Device Switching Characteristics of the SDA and SCL Bus Lines
STANDARD
MODE
PARAMETER
MIN
MAX
FAST
MODE
MIN
UNIT
MAX
10
2.5
µs
4
0.6
µs
tc(SCL)
tw(SCLH)
Cycle time, SCL
tw(SCLL)
tr(SCL)
Pulse duration, SCL low
Rise time, SCL
1000
300
ns
tf(SCL)
tr(SDA)
Fall time, SCL
300
300
ns
Rise time, SDA
1000
300
ns
tf(SDA)
Fall time, SDA
300
300
ns
tw(SP)
tsu(SDA–SCLH)
Pulse duration, spike suppression
50
ns
Setup time, SCL high after SDA valid
250
th(SDA–SCLL)
Hold time, SCL low after SDA invalid
0
0.9
µs
Pulse duration, SCL high
tc(SCL)
4.7
µs
1.3
0
100
3.45
ns
0
tsu(SDA–SCLH)
tw(SCLL)
th(SDA–SCLL)
tw(SCLH)
SCL
tr(SCL)
tw(SP)
tf(SCL)
SDA
tr(SDA)
tf(SDA)
Figure 6–30. Definition of Timing on the I2C Bus
December 2001 – Revised December 2002
SPRS017B
73
Electrical Specifications
Table 6–31. I2C Bus Device Timing Requirements (STOP and START Conditions)
STANDARD
MODE
MIN
th(SDAL–SCLL1)
tsu(SCLH-SDAH)
MIN
UNIT
MAX
Hold time, SCL low from SDA low (START condition)
4
0.6
µs
Setup time, SDA high from SCL high (STOP condition)
4
0.6
µs
4.7
1.3
µs
Pulse duration, SDA high. Bus free time between a STOP and START
condition.
tw(SDAH)
MAX
FAST
MODE
SCL
tw(SDAH)
SDA
th(SDAL–SCLL1)
tsu(SCLH–SDAH)
th(SDAL–SCLL1)
Figure 6–31. I2C Bus Timings (STOP and START Conditions)
Table 6–32. I2C Bus Device Timing Requirements (Repeated START Condition)
STANDARD
MODE
MIN
tsu(SCLH–SDAL)
td(SDAL–SCLL2)
Setup time, SDA low after SCL high
Hold time, SCL low after SDA low
MAX
FAST
MODE
MIN
UNIT
MAX
4.7
0.6
µs
4
0.6
µs
Repeated
Start
tsu(SCLH–SDAL)
th(SDAL–SCLL2)
SCL
SDA
Figure 6–32. I2C Bus Timings (Repeated START Condition)
74
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.14 ARM Clock Timings
The ARM SRAM timings are derived from the ARM clock. The clock switching characteristics are defined in
Table 6–33 for use in the ARM SRAM timing definitions.
Table 6–33. ARM SRAM Switching Characteristics
PARAMETER
A
B
C
D
tc(ARM)
tw(ARM–H)
Cycle time, ARM clock
tw(ARM–L)
tw(ARM–W)
Pulse duration, ARM clock low
Pulse duration, ARM clock high
MIN
TYP
MAX
A/2†
A/2†
A/2 + 3†
A/2 + 3†
21.05
A/2 – 3†
A/2 – 3†
ns
A/2 + nA†‡
A + nA†‡
Pulse duration, ARM write cycle
E
tw(ARM–R)
Pulse duration, ARM read cycle
† A = tc(ARM)
‡ n = the number of software wait states
UNIT
ns
ns
ns
ns
The ARM SRAM write timing requirements listed in Table 6–34 represent back-to-back write operations to
a zero-wait-state SRAM device.
Table 6–34 through Table 6–35 assume testing over recommended operating conditions (see Figure 6–33
and Figure 6–34).
Table 6–34. ARM SRAM Timing Requirements (Write)
MIN
1
NOM
MAX
UNIT
td(CSL-AV)
td(CSL-DV)
Delay time, address valid from CS low
–3
4
ns
Delay time, data valid from CS low
–2
5
ns
td(CSL-WEL)
tw(WEL)
Delay time, write enable low from CS low
4
13
ns
D + 3.5§
ns
Delay time, address invalid from write enable high
0
7
ns
6
td(WEH–AIV)
td(WEH–DIV)
Delay time, data invalid from write enable high
0
7
ns
7
td(WEH–DV)
Delay time, data valid from write enable high
2
9
ns
A/2 + 3.5†
ns
2
3
4
5
Pulse width, write enable low
D – 3.5§
A/2 – 3.5†
D§
A/2†
8
tw(WEH)
Pulse width, write enable high
9
td(WEH–CSH)
Delay time, CS high from write enable high
0
7
ns
10
td(CSL–BEV)
Delay time, byte enable valid from CS low
–3
4
ns
11
td(WEH–BEIV)
Delay time, byte enable invalid from write enable high
0
7
ns
12
td(WEH–BEV)
Delay time, byte enable valid from write enable high
2
9
ns
20
td(CSL-OEH)
Delay time, output enable high from CS low
–3
4
ns
0
7
ns
21 td(WEH–OEL)
† A = tc(ARM)
§ D = tw(ARM-W)
Delay time, output enable low from write enable high
December 2001 – Revised December 2002
SPRS017B
75
Electrical Specifications
A
ARM_MCLK
B
C
D†
D‡
1
5
5
ADD[22:0]
2
7
6
6
DATA[31:0]
3
4
4
8
R/W
9
CSn
12
11
10
11
BE[3:0]
20
21
OE
† n = 0 wait states
‡ n = 1 or more wait states
NOTE: When performing a 32-bit access on a 16-bit-wide SRAM, two of the byte-enables will be active at the same time. The particular byte-enables
active depend on the endiannism selected.
Figure 6–33. ARM SRAM Write Timing
76
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
The ARM SRAM read timing requirements listed in Table 6–35 represent back-to-back read operations to a
zero-wait-state SRAM device.
Table 6–35. ARM SRAM Timing Requirements (Read)
MIN
MAX
UNIT
Delay time, address valid from CS low
–3
4
ns
2
td(CSL-AV)
td(CSL–BHEV1)
Delay time, byte enable high valid 1 from CS low
–3
4
ns
3
td(CSL-OEL)
Delay time, output enable low from CS low
–3
4
ns
4
td(CSL-AIV1)
tw(CSL)
Delay time, address invalid 1 from CS low
tsu(CSL-DV1)
td(CSL–AIV2)
Setup time, data valid 1 from CS low
1
5
6
7
8
9
10
th(CSL–DIV1)
tsu(CSL–DV2)
td(CSL–BEIV1)
E – 3†
E + 4†
ns
2E – 3.5†
2E + 3.5†
ns
Delay time, address invalid 2 from CS low
E – 12†
2E – 3†
2E + 4†
Hold time, data invalid 1 from CS low
E – 1†
Setup time, data valid 2 from CS low
2E – 12†
Pulse duration, CS low
ns
ns
ns
ns
Delay time, byte enable invalid 1 from CS low
E – 4†
E + 4†
ns
E + 6†
ns
11
td(CSL–BEV2)
Delay time, byte enable valid 2 from CS low
E – 2†
12
th(CSL–DIV2)
td(CSL–BEIV2)
Hold time, data invalid 2 from CS low
Delay time, byte enable invalid 2 from CS low
2E – 1†
2E – 4†
2E + 4†
ns
Delay time, output enable high from CS low
2E – 3†
2E + 4†
ns
13
14 td(CSL–OEH)
† E = tw(ARM–R)
December 2001 – Revised December 2002
ns
SPRS017B
77
Electrical Specifications
A
C
E‡
B
E†
ARM_MCLK
7
4
1
ADD[22:0]
6
9
12
8
DATA[31:0]
R/W
5
CSn
13
10
11
2
BE[3:0]
14
3
OE
† n = 0 wait states
‡ n = 1 or more wait states
NOTE: When performing a 32-bit access on a 16-bit-wide SRAM, two of the byte-enables will be active at the same time. The particular byte-enables
active depend on the endiannism selected.
Figure 6–34. ARM SRAM Read Timing
78
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
6.15 SPI Clock Timings
SPI timings are derived from the internal SPI clock. This clock is only available externally during a serial
transfer.
Table 6–36 through Table 6–38 assume testing over recommended operating conditions (see Figure 6–35
and Figure 6–36).
Table 6–36. SPI Clock Switching Characteristics
PARAMETER
MIN
TYP
168.4
A†
Pulse duration, CLKX_SPI high
A/2 – 3†
A/2†
A/2 + 3†
ns
tw(SPI–L)
Pulse duration, CLKX_SPI low
A/2 – 3†
A/2†
A/2 + 3†
ns
tr(SPI)
Rise time, SPI output signals.
CLKX_SPI, MCUDO, MCUEN0,
MCUEN1, and MCUEN2
1
4
ns
tf(SPI)
Fall time, SPI output signals.
CLKX_SPI, MCUDO, MCUEN0,
MCUEN1, and MCUEN2
1
4
ns
tc(SPI)
Cycle time, CLKX_SPI
tw(SPI–H)
MAX
UNIT
ns
† A = 4 x PTV x tc(ARM)
Table 6–37. SPI Falling Edge Timing Requirements
MIN
NOM
MAX
UNIT
A/2 – 3†
A/2 + 3†
A + 3†
ns
A + 3†
ns
8
ns
Delay time, Last clock low to falling enable end
A – 3†
A/2†
A†
tw(ENFT)
Pulse duration, Falling enable toggle
A – 3†
A†
td(CLKH–DOV)
Delay time, Clock high to data out valid
2
tsu(DIV–CLKL)
Setup time, Data in valid to clock low
6
ns
th(CLKL–DIIV)
Hold time, Clock low to data in invalid
† A = 4 x PTV x tc(ARM)
4
ns
td(ENFS–CLKH)
td(CLKL–ENFE)
Delay time, Falling enable start active to first clock high
ns
In this mode, all timing related activity for Data In and Enable is based on the falling edge of the SPI Clock.
The timing activity for Data Out will be based on the rising edge of the SPI clock.
December 2001 – Revised December 2002
SPRS017B
79
Electrical Specifications
A
MCUENO, 1 2,
(negative edge
triggered)
MCUENO, 1 2,
(positive edge
triggered)
MCUENO, 1 2,
(negative level
triggered)
MCUENO, 1 2,
(positive level
triggered)
tc(SPI)
tr(SPI)
tw(SPI–H)
tw(SPI–L)
td(ENFS–CLKH)
td(CLKL–ENFE)
tw(ENFT)
tf(SPI)
CLKX_SPI
13
MCUDO
MSB
Bit=31
MCUDI
LSB
td(CLKL–DIIV)
tsu(DIV–CLKL)
Bit=32–total
MSB
LSB
Bit=total–1
Bit=0
Figure 6–35. SPI Falling Edge Timings
80
SPRS017B
December 2001 – Revised December 2002
Electrical Specifications
Table 6–38. SPI Rising Edge Timing Requirements
MIN
NOM
MAX
UNIT
A – 3†
A†
A/2†
A + 3†
ns
A/2 – 3†
A/2 + 3†
ns
A†
A + 3†
ns
8
ns
td(ENRS–CLKH)
td(CLKL–ENRE)
Delay time, Rising enable start active to first clock high
tw(ENRT)
Pulse duration, Rising enable toggle
A – 3†
td(CLKL–DOV)
Delay time, Clock low to data out valid
2
tsu(DIV–CLKH)
Setup time, Data in valid to clock high
6
ns
th(CLKH–DIIV)
Hold time, Clock high to data in invalid
† A = 4 x PTV x tc(ARM)
4
ns
Delay time, Last clock low to rising enable end
In this mode, all timing related activity for Data In and Enable is based on the falling edge of the SPI Clock.
The timing activity for Data Out will be based on the rising edge of the SPI clock.
MCUENO, 1 2,
(negative edge
triggered)
MCUENO, 1 2,
(positive edge
triggered)
MCUENO, 1 2,
(negative level
triggered)
MCUENO, 1 2,
(positive level
triggered)
tc(SPI)
tw(SPI–H)
tr(SPI)
tw(SPI–L)
td(ENRS–CLKH)
td(CLKL–ENRE)
tw(ENRT)
tf(SPI)
CLKX_SPI
td(CLKL–DOV)
MCUDO
MSB
LSB
Bit=31
Bit=32–total
th(CLKH–DIIV)
tsu(DIV–CLKH)
MCUDI
MSB
LSB
Bit=total–1
Bit=0
Figure 6–36. SPI Rising Edge Timings
December 2001 – Revised December 2002
SPRS017B
81
Mechanical Data
7
Mechanical Data
7.1
Ball Grid Array Mechanical Data
GHK (S-PBGA-N257)
PLASTIC BALL GRID ARRAY
16,10
15,90
14,40 TYP
SQ
0,80
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
A1 Corner
0,80
1
3
2
5
4
7
6
0,95
0,85
9
11 13 15 17 19
8
10 12 14 16 18
Bottom View
1,40 MAX
Seating Plane
0,55
0,08
0,45
0,45
0,35
0,12
4145273-3/E 08/02
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice
C. MicroStar BGA configuration
Figure 7–1. TMS320VC5470 257-Ball MicroStar BGA Plastic Ball Grid Array Package
MicroStar BGA is a trademark of Texas Instruments.
82
SPRS017B
December 2001 – Revised December 2002
PACKAGE OPTION ADDENDUM
www.ti.com
17-Dec-2004
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TMS320VC5470GHK
ACTIVE
BGA
GHK
257
90
None
SNPB
Level-3-220C-168HR
TMS320VC5470GHKA
ACTIVE
BGA
GHK
257
90
None
SNPB
Level-3-220C-168HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1