TI TPS71530QDCKRQ1

TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
50-mA, 24-V, 3.2-µA Supply Current
Low-Dropout Linear Regulators in SC70 Package
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
(1)
Qualification in Accordance With
AEC-Q100 (1)
Qualified for Automotive Applications
Customer-Specific Configuration Control Can
Be Supported Along With Major-Change
Approval
24-V Maximum Input Voltage
Low 3.2-µA Quiescent Current at 50 mA
Stable With Any Capacitor (>0.47 µF)
50-mA Low-Dropout Regulator
Available in 2.5 V, 3 V, 3.3 V, 5 V, and
Adjustable (1.2 V to 15 V)
Minimum/Maximum Specified Current Limit
5-Pin SC70/SOT-323 (DCK) Package
–40°C to 125°C Specified Junction
Temperature Range
Ultra-Low-Power Microcontrollers
Cellular/Cordless Handsets
Portable/Battery-Powered Equipment
DESCRIPTION
The TPS715xx low-dropout (LDO) voltage regulators
offer the benefits of high input voltage, LDO voltage,
low-power operation, and miniaturized packaging.
The devices, which operate over an input range of
2.5 V to 24 V, are stable with any capacitor
(>0.47 µF). The LDO voltage and low quiescent
current allow operations at extremely low power
levels. Therefore, the devices are ideal for powering
battery-management ICs. Specifically, since the
devices are enabled as soon as the applied voltage
reaches the minimum input voltage, the output is
quickly available to power continuously operating
battery-charging ICs.
The usual PNP pass transistor has been replaced by
a PMOS pass element. Because the PMOS pass
element behaves as a low-value resistor, the LDO
voltage, typically 415 mV at 50 mA of load current, is
directly proportional to the load current. The low
quiescent current (3.2 µA typ) is stable over the
entire range of output load current (0 mA to 50 mA).
Contact Texas Instruments for details. Q100 qualification data
available on request.
DCK PACKAGE
(TOP VIEW)
FB/NC
1
GND
2
NC
3
5
IN
OUT
OUT
TPS715xx
MSP430
Li–
4
IN
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OPTIONS (1)
TJ
–40°C to 125°C
(1)
VOLTAGE
PACKAGE
PART NUMBER
SYMBOL
2.5 V
SC70/SOT-323 (DCK)
TPS71525QDCKRQ1
ANU
3V
SC70/SOT-323 (DCK)
TPS71530QDCKRQ1
ANV
3.3 V
SC70/SOT-323 (DCK)
TPS71533QDCKRQ1
ANW
5V
SC70/SOT-323 (DCK)
TPS71550QDCKRQ1
ANX
(Adjustable) 1.2 V–15 V
SC70/SOT-323 (DCK)
TPS71501QDCKRQ1
ANS
Contact Texas Instruments for other voltage options between 1.25 V and 5.85 V.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2007, Texas Instruments Incorporated
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
ABSOLUTE MAXIMUM RATINGS
over operating temperature range (unless otherwise noted) (1) (2)
UNIT
VIN range
–0.3 V to 24 V
VOUT range
–0.3 V to 16.5 V
Peak output current
Internally limited
ESD rating, HBM
2 kV
ESD rating, CDM
500 V
Continuous total power dissipation
See Dissipation Rating Table
Junction temperature range, TJ
–40°C to 150°C
Storage temperature range, Tstg
–65°C to 150°C
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
PACKAGE
RθJC°C/W
RθJA°C/W
DERATING FACTOR
ABOVE TA = 25°C
Low-K (1)
DCK
165
395
2.52 mW/°C
250 mW
140 mW
100 mW
High-K (2)
DCK
165
315
3.18 mW/°C
320 mW
175 mW
130 mW
(1)
(2)
2
TA ≤ 25°C
TA = 70°C
TA = 85°C
POWER RATING POWER RATING POWER RATING
BOARD
The JEDEC Low-K (1s) board design used to derive this data was a 3-in × 3-in, two-layer board with 2-oz copper traces on top of the
board.
The JEDEC High-K (2s2p) board design used to derive this data was a 3-in × 3-in, multilayer board with 1-oz internal power and ground
planes and 2-oz copper traces on top and bottom of the board.
Submit Documentation Feedback
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
ELECTRICAL CHARACTERISTICS
over operating junction temperature range (TJ = –40°C to 125°C), VIN = VOUT(NOM) + 1 V, IOUT = 1 mA, COUT = 1 µF (unless
otherwise noted). Typical values are at TJ = 25°C.
PARAMETER
TEST CONDITIONS
Input voltage (1)
VIN
VOUT
over VIN, IOUT, and T
TYP
24
IO = 50 mA
3
24
1.2
15
VIN + 1 V ≤ VIN ≤ 24 V , 100 µA ≤ IOUT ≤ 50 mA
–4%
Ground-pin current
0 mA ≤ IOUT ≤ 50 mA
3.2
∆VOUT/∆IOUT
Load regulation
IOUT = 100 µA to 50 mA
22
∆VOUT/∆VIN
Output voltage line regulation
VOUT + 1 V < VIN ≤ 24 V
20
Vn
Output noise voltage
BW = 200 Hz to 100 kHz, COUT = 10 µF,
IOUT = 50 mA
ICL
Output current limit
VO = 0 V
PSRR
Power-supply ripple rejection
f = 100 kHz, COUT = 10 µF
VDO
Dropout voltage,
VIN = VOUT(NOM) – 1 V
IOUT = 50 mA
(1)
UNIT
V
V
4%
IGND
(1)
MAX
2.5
VOUT voltage range (TPS71501)
accuracy (1)
MIN
IO = 10 mA
12
60
750
60
415
mV
µVrms
575
125
µA
mV
mA
dB
750
mV
Minimum VIN = VOUT + VDO or the value shown for input voltage in this table, whichever is greater.
Submit Documentation Feedback
3
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
FUNCTIONAL BLOCK DIAGRAMS
V(OUT)
V(IN)
Current
Sense
Leakage Null
Control Circuit
ILIM
_
GND
R1
+
FB
R2
Vref = 1.205 V
Bandgap
Reference
Figure 1. Functional Block Diagram—Adjustable Version
V(OUT)
V(IN)
Current
Sense
Leakage Null
Control Circuit
ILIM
_
GND
Bandgap
Reference
R1
+
Vref = 1.205 V
R2
Figure 2. Functional Block Diagram—Fixed Version
Table 1. Terminal Functions
TERMINAL
NAME
NO.
FIXED
FB
4
DESCRIPTION
ADJ.
1
Adjustable version. This terminal is used to set the output voltage.
NC
1
No connection
GND
2
2
Ground
NC
3
3
No connection
IN
4
4
Input supply.
OUT
5
5
Output of the regulator, any output capacitor ≥ 0.47 µF can be used for stability.
Submit Documentation Feedback
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
3.320
3.32
VOUT − Output Voltage − V
3.305
3.300
3.295
3.290
10
20
30
40
3.28
3.27
3.26
VIN = 4.3 V
COUT = 1 µF
−40 −25 −10 5
20 35 50 65 80 95 110 125
TJ − Free-Air Temperature − °C
Figure 5.
OUTPUT SPECTRAL
NOISE DENSITY
vs
FREQUENCY
OUTPUT IMPEDANCE
vs
FREQUENCY
DROPOUT VOLTAGE
vs
OUTPUT CURRENT
600
VIN = 4.3 V
VOUT = 3.3 V
COUT = 1 µF
TJ = 25°C
16
6
IOUT = 50 mA
4
3
2
14
12
V DO − Dropout Voltage − mV
VIN = 4.3 V
VOUT = 3.3 V
COUT = 1 µF
IOUT = 1 mA
10
8
6
IOUT = 1 mA
4
2
1
0
100
1k
10 k
f − Frequency − Hz
100 k
VIN = 3.2 V
COUT = 1 µF
500
TJ = 125°C
400
TJ = 25°C
300
200
TJ = −40°C
100
IOUT = 50 mA
0
10
100
1k
10k
100k
1M
0
10 M
0
f − Frequency − Hz
10
20
30
40
IOUT − Output Current − mA
Figure 6.
Figure 7.
Figure 8.
TPS71501
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
POWER-SUPPLY
RIPPLE REJECTION
vs
FREQUENCY
1
600
IOUT = 50 mA
VIN = 3.2 V
0.8
V DO − Dropout Voltage − mV
0.9
TJ = 125°C
0.7
TJ = 25°C
0.6
0.5
0.4
TJ = −40°C
0.3
0.2
500
IOUT = 50 mA
400
300
200
IOUT = 10 mA
100
0.1
0
0
2.5
2
18
5
3
Figure 4.
8
7
3.5
Figure 3.
Zo − Output Impedance − Ω
Hz
µ V/
IOUT = 50 mA
3.29
VIN = 4.3 V
VOUT = 3.3 V
IOUT = 1 µF
4
3.30
3.25
−40 −25 −10 5 20 35 50 65 80 95 110 125
TJ − Free−Air Temperature − °C
50
IO − Output Current − mA
Output Spectral Noise Density −
IOUT = 1 mA
3
6
9
VIN − Input Voltage − V
Figure 9.
12
15
0
−40 −25 −10 5 20 35 50 65 80 95 110 125
TJ − Free-Air Temperature − °C
Figure 10.
Submit Documentation Feedback
PSRR − Power Supply Ripple Rejection − dB
VOUT − Output Voltage − V
3.31
3.310
0
4.5
IGND − Ground Current − µ A
VIN = 4.3 V
COUT = 1 µF
TJ = 25°C
3.315
V DO − Dropout Voltage − V
QUIESCENT CURRENT
vs
FREE-AIR TEMPERATURE
50
100
VIN = 4.3 V
VOUT = 3.3 V
COUT = 10 µF
TJ = 25°C
90
80
70
60
IOUT = 1 mA
50
40
30
20
IOUT = 50 mA
10
0
10
100
1k
10k
100k
1M
10 M
f − Frequency − Hz
Figure 11.
5
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
TYPICAL CHARACTERISTICS (continued)
VOUT = 3.3 V
RL = 66 Ω
COUT = 10 µF
6
VIN − Input Voltage − V
VOUT − Output Voltage − V
7
5
50
0
−50
4
3
VIN
2
VOUT
1
0
0
2
4
6
8 10 12 14
t − Time − ms
Figure 12.
6
VOUT = 3.3 V
IOUT = 50 mA
COUT = 10 µF
100
16 18
20
5.3
4.3
0
50 100 150 200 250 300 350 400 450 500
t − Time − ms
Figure 13.
Submit Documentation Feedback
LOAD TRANSIENT RESPONSE
D VOUT − Change In
Output Voltage − mV IOUT − Output Current − mV
LINE TRANSIENT RESPONSE
VIN − Input Voltage − V
VOUT − Output Voltage − mV
POWER UP / POWER DOWN
8
400
200
VIN = 4.3 V
VOUT = 3.3 V
COUT = 10 µF
0
-200
60
40
20
0
0 100 200 300 400 500 600 700 800 900 1000
t − Time − µs
Figure 14.
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
APPLICATION INFORMATION
The TPS715xx family of LDO regulators has been optimized for ultra-low power applications such as the
MSP430 microcontroller. Its ultralow supply current maximizes efficiency at light loads and its high input voltage
range makes it suitable for supplies such as unconditioned solar panels.
4
VI
C1
0.1 µF
IN
OUT
5
VO
3
NC
1
NC/FB
GND
0.47 µF
2
Figure 15. Typical Application Circuit (Fixed Voltage Version)
External Capacitor Requirements
Although not required, a 0.047-µF or larger input bypass capacitor, connected between IN and GND and located
close to the device, is recommended to improve transient response and noise rejection of the power supply as a
whole. A higher-value input capacitor may be necessary if large, fast-rise-time load transients are anticipated
and the device is located several inches from the power source.
The TPS715xx requires an output capacitor connected between OUT and GND to stabilize the internal control
loop. Any capacitor (including ceramic and tantalum) ≥0.47 µF properly stabilizes this loop.
Power Dissipation and Junction Temperature
To ensure reliable operation, worst-case junction temperature should not exceed 125°C. This restriction limits
the power dissipation the regulator can handle in any given application. To ensure the junction temperature is
within acceptable limits, calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD,
which must be less than or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
T max * T
A
P
+ J
D(max)
R
qJA
(1)
where:
TJmax = Maximum allowable junction temperature
RθJA = Thermal resistance junction-to-ambient for the package (see the Dissipation Ratings table)
TA = Ambient temperature
The regulator dissipation is calculated using:
P
D
ǒ
+ V *V
I
O
Ǔ
I
O
(2)
Power dissipation resulting from quiescent current is negligible.
Submit Documentation Feedback
7
TPS71501-Q1
TPS71525-Q1, TPS71530-Q1
TPS71533-Q1, TPS71550-Q1
www.ti.com
SGLS272C – OCTOBER 2004 – REVISED APRIL 2007
APPLICATION INFORMATION (continued)
Regulator Protection
The TPS715xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be
appropriate.
The TPS715xx features internal current limiting. During normal operation, the TPS715xx limits output current to
approximately 500 mA. When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. Take care not to exceed the power dissipation ratings of the package.
Programming the TPS71501 Adjustable LDO Regulator
The output voltage of the TPS71501 adjustable regulator is programmed using an external resistor divider as
shown in Figure 16. The output voltage is calculated using:
V
O
+V
ǒ1 ) R1
Ǔ
R2
ref
(3)
where:
VREF = 1.205 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 1.5-µA divider current. Lower value resistors can be
used for improved noise performance, but the solution consumes more power. Higher resistor values should be
avoided as leakage current into/out of FB across R1/R2 creates an offset voltage that artificially
increases/decreases the feedback voltage and thus erroneously decreases/increases VO. The recommended
design procedure is to choose R2 = 1 MΩ to set the divider current at 1.5 µA and then calculate R1 using:
R1 +
ǒ
Ǔ
V
V
O *1
ref
R2
(4)
TPS71501
VI
OUTPUT VOLTAGE
PROGRAMMING GUIDE
IN
0.1 µF
OUT
VO
R1
0.47 µF
FB
GND
OUTPUT
VOLTAGE
R1
R2
1.8 V
0.499 MΩ
1 MΩ
2.8 V
1.33 MΩ
1 MΩ
5V
3.16 MΩ
1 MΩ
R2
Figure 16. TPS71501 Adjustable LDO Regulator Programming
8
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS71501QDCKRQ1
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS71525QDCKRQ1
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS71530QDCKRQ1
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS71533QDCKRQ1
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS71550QDCKRQ1
ACTIVE
SC70
DCK
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power
Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated