5 V, SUPER MINIMOLD WIDEBAND SI RFIC AMPLIFIER UPC2708TB GAIN vs. FREQUENCYand TEMPERATURE FEATURES • HIGH DENSITY SURFACE MOUNTING: 6 pin super minimold or SOT-363 package • HIGH GAIN: 15 dB TYP TA = -40°C TA = +85°C Gain, GS (dB) • SATURATED OUTPUT POWER: +10 dBm • WIDEBAND RESPONSE: fu = 2.9 GHz TYP • SUPPLY VOLTAGE: VCC = 4.5 to 5.5 V TA = +25°C TA = +85°C TA = -40°C TA = +25°C DESCRIPTION NEc's UPC2708TB is a Silicon RFIC manufactured using the NESAT III process. This device is suitable as buffer amplifier for DBS, PCS and other communication receivers. The UPC2708TB is pin compatible and has comparable performance as the larger UPC2708T, so it is suitable for use as a replacement to help reduce system size. The IC is housed in a 6 pin super minimold or SOT-363 package. Frequency, f (GHz) NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. ELECTRICAL CHARACTERISTICS (TA = 25 °C, f = 1 GHz, VCC = 5 V) PART NUMBER PACKAGE OUTLINE SYMBOLS PARAMETERS AND CONDITIONS UPC2708TB S06 UNITS MIN TYP MAX ICC Circuit Current (no signal) mA 20 26 33 GS Small Signal Gain dB 13 15 18.5 fU Upper Limit Operating Frequency (The gain at fU is 3 dB down from the gain at 0.1 GHz) GHz 2.7 ∆GS Gain Flatness, f = 0.1 - 2.6 GHz PSAT Saturated Output Power dBm P1dB Output Power at 1 dB Compression Point NF RLIN dB 2.9 ±0.8 +7.5 +10 dBm +7.5 Noise Figure dB 6.5 Input Return Loss dB 8 8 11 RLOUT Output Return Loss dB 16 20 ISOL Isolation dB 18 23 ∆GT Gain-Temperature Coefficient dB/°C RTH Thermal Resistance (Junction to Ambient) °C/W +0.002 325 UPC2708TB ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS VCC Supply Voltage PIN Input Power RECOMMENDED OPERATING CONDITIONS UNITS RATINGS V 6 SYMBOL dBm +10 VCC mW 200 2 PT Power Dissipation TOP Operating Temperature °C -40 to +85 TSTG Storage Temperature °C -55 to +150 PARAMETER UNITS MIN TYP MAX V 4.5 5.0 Supply Voltage Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on 50 x 50 x 1.6 mm epoxy glass PWB (TA = +85°C). TYPICAL PERFORMANCE CURVES (TA = 25°C) CIRCUIT CURRENT vs. TEMPERATURE CIRCUIT CURRENT vs. VOLTAGE 40 40 VCC = 5.0 V Circuit Current, ICC (mA) Circuit Current, ICC (mA) 35 30 20 10 30 25 20 15 10 5 0 0 0 1 2 3 4 5 -60 -40 6 -20 0 20 40 60 80 Supply Voltage, VCC (V) Operating Temperature, TOP (°C) GAIN AND NOISE FIGURE vs. FREQUENCY AND VOLTAGE INPUT RETURN LOSS, OUTPUT RETURN LOSS vs. FREQUENCY 20 100 0 VCC = 5.0 V 9 8 15 VCC = 4.5 V 7 VCC = 5.0 V 5.5 V 10 6 NF 4.5 V Input Return Loss (dB) Output Return Loss (dB) Gain, GS (dB) Gp Noise Figure, NF (dB) VCC = 5.0 V VCC = 5.5 V -10 RLin -20 RLout -30 5 -40 5 0.1 0.3 1.0 Frequency, f (GHz) 3.0 0.1 0.3 1.0 Frequency, f (GHz) 3.0 5.5 UPC2708TB TYPICAL PERFORMANCE CURVES (TA = 25°C) ISOLATION vs. FREQUENCY POWER vs. FREQUENCY 25 0 VCC = 5.0 V VCC = 5.0 V 20 Power (dBm) Isolation, ISOL (dB) -10 -20 -30 X 15 X X 10 PSAT P1dB 5 -40 0 -5 -50 0.1 0.3 1.0 3.0 0 1.0 1.5 2.0 2.5 3.0 3.5 Frequency, f (GHz) Frequency, f (GHz) X: Typical SSB Third Order intercept Point OUTPUT POWER vs. INPUT POWER AND TEMPERATURE OUTPUT POWER vs. INPUT POWER AND VOLTAGE 15 15 f = 1.0 GHZ VCC = 5.0 V f = 1.0 GHZ 85°C 10 5 Output Power, Pout (dBm) Output Power, Pout (dBm) 0.5 TA = -25°C -40°C 0 -5 -10 -15 5.5 V 10 5 VCC = 5.0 V 4.5 V 0 -5 -10 -15 -20 -20 -30 -25 -20 -15 -10 -5 0 5 -30 -25 -20 -15 -10 -5 0 Input Power, PIN (dBm) Input Power, PIN (dBm) NOISE FIGURE vs. FREQUENCY OUTPUT POWER vs. INPUT POWER AND VOLTAGE 10 +15 9 +10 5 Output Power, Pout (dBm) Noise Figure, NF (dB) f = 2.0 GHz 8 7 6 5 VCC = 5.5 V +5 VCC = 5.0 V 0 VCC = 4.5 V -5 -10 -15 4 0 0.5 1.0 1.5 2.0 Frequency, f (GHz) 2.5 3.0 -20 -30 -25 -20 -15 -10 -5 Input Power, PIN (dBm) 0 +5 UPC2708TB TYPICAL PERFORMANCE CURVES (TA = 25°C) SATURATED OUTPUT POWER vs. FREQUENCY and VOLTAGE OUTPUT POWER vs. INPUT POWER AND FREQUENCY +15 Output Power, Pout (dBm) VCC = 5.0 V Saturated Output Power, PO(sat) (dBm) +15 f = 1.0 GHz +10 +5 f = 2.0 GHz 0 f = 2.9 GHz -5 -10 -15 -20 -30 Third Order Intermodulation Distortion, IM3 (dBc) PIN = 0 dBm VCC = 5.0 V +10 VCC = 4.5 V +5 0 -25 -20 -15 -10 -5 0 +5 Input Power, PIN (dBm) -60 f1 = 1.000 GHz f2 = 1.002 GHz -50 VCC = 5.0 V -40 VCC = 5.5 V -30 VCC = 4.5 V -20 -10 -8 -6 -4 -2 0 +2 +4 +6 Input Power, PIN (dBm) 0.1 0.3 1.0 Frequency, f (GHz) THIRD ORDER INTERMODULATION DISTORTION vs. OUTPUT POWER OF EACH TONE and VOLTAGE -10 VCC = 5.5 V +8 +10 3.0 UPC2708TB TYPICAL SCATTERING PARAMETERS (TA = 25°C, VCC = VOUT = 5.0 V) 1.0 GHz 2.0 GHz 3.0 GHz 0.1 GHz 0.1 GHz 2.0 GHz 3.0 GHz S22 S11 UPC2708TB VCC = VOUT = 5 V, ICC = 27 mA FREQUENCY S11 S21 GHz MAG ANG 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 0.039 0.053 0.069 0.088 0.105 0.123 0.144 0.164 0.186 0.205 0.226 0.245 0.263 0.286 0.308 0.328 0.344 0.364 0.382 0.395 0.405 0.417 0.427 0.431 0.431 0.434 0.423 0.419 0.408 0.400 0.386 138.9 119.7 106.7 97.2 91.6 84.9 79.7 74.7 70.7 66.1 61.7 57.7 53.7 48.6 44.3 40.7 36.2 31.0 26.0 21.2 16.8 11.8 6.6 2.2 -3.0 -8.2 -12.3 -17.1 -21.5 -26.2 -29.3 S12 S22 MAG ANG MAG ANG MAG 5.815 5.822 5.815 5.813 5.794 5.823 5.871 5.890 5.938 5.960 6.072 6.097 6.174 6.275 6.371 6.419 6.470 6.555 6.542 6.570 6.528 6.527 6.438 6.336 6.247 6.127 5.952 5.816 5.619 5.354 5.134 -4.8 -9.8 -14.3 -18.8 -23.8 -28.4 -33.0 -38.2 -42.8 -47.6 -52.7 -57.5 -63.0 -68.4 -74.3 -79.8 -85.9 -92.1 -98.3 -104.7 -111.3 -118.5 -124.7 -131.3 -138.1 -145.0 -151.7 -158.2 -165.0 -171.5 -177.4 0.077 0.075 0.074 0.074 0.072 0.071 0.070 0.071 0.073 0.070 0.069 0.070 0.067 0.069 0.070 0.066 0.067 0.069 0.070 0.070 0.070 0.071 0.072 0.071 0.072 0.071 0.071 0.070 0.073 0.074 0.075 -0.8 -1.5 -0.6 -0.5 -1.1 -0.6 0.1 0.5 2.3 4.4 5.0 4.4 2.5 5.0 5.4 7.1 5.6 8.2 8.4 8.7 10.1 9.4 9.5 10.7 12.8 15.4 14.5 16.1 15.3 17.1 17.1 0.051 0.048 0.049 0.054 0.054 0.056 0.060 0.065 0.072 0.082 0.091 0.082 0.085 0.091 0.092 0.097 0.096 0.100 0.092 0.101 0.100 0.096 0.098 0.095 0.098 0.094 0.088 0.081 0.074 0.065 0.053 K ANG 0.9 1.4 5.9 8.9 8.8 10.4 11.5 11.6 11.1 5.6 -4.6 5.6 0.6 -4.6 -8.2 -12.6 -19.6 -23.9 -8.2 -38.9 -47.2 -57.2 -66.1 -76.5 -86.1 -99.9 -116.7 -134.4 -149.7 -170.3 172.8 1.34 1.36 1.38 1.36 1.39 1.40 1.40 1.37 1.34 1.31 1.28 1.31 1.33 1.28 1.24 1.26 1.23 1.18 1.24 1.13 1.12 1.09 1.09 1.09 1.09 1.10 1.14 1.18 1.19 1.24 1.28 UPC2708TB PIN DESCRIPTIONS Pin No. Symbol Applied Voltage (V) Pin Voltage (V) 1 Input – 1.16 4 Output – Internal Equivalent Circuit Description Signal input pin. An internal matching circuit, configured with resistors, enables 50 Ω connection over a wide bandwidth. A multi-feedback circuit is designed to cancel the deviations of hFE and resistance. This pin must be coupled to the signal source with a blocking capacitor. Signal output pin. Connect an inductor between this pin and VCC to supply current to the internal output transistors. 6 VCC 4.5 to 5.5 – Power supply pin. This pin should be externally equipped with a bypass capacitor to minimize ground impedance. 2 3 5 GND 0 – Ground pins. These pins should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be connected together with wide ground pattern to minimize impedance difference. 6 VCC OUT 4 1 IN 2, 3, 5 SYSTEM APPLICATION EXAMPLE EXAMPLE OF DBS CONVERTERS BS Antenna (DBS ODU) RF Amp. Mixer UPC2711TB UPC2712TB IF Amp. Parabola Antenna To IDU UPC2708TB Oscillator EXAMPLE OF 2.4 GHz BAND RECEIVER RX DEMO SW PLL I Q PLL I Driver TX 0˚ φ PA UPC2708TB 90˚ Q UPC2708TB ORDERING INFORMATION OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S06 (Top View) PART NUMBER MARKING UPC2708TB-E3-A QTY C1D 3K/Reel Note: Embossed Tape, 8 mm wide. Pins 1, 2 and 3 face perforated side of tape. 2.1±0.1 1.25±0.1 0.2 +0.1 -0 2.0±0.2 0.65 3 4 0.65 2 5 1 6 1.3 DOT ON BACK SIDE 0.9 ± 0.1 0.7 +0.1 0.15 -0.5 0 ~0.1 TEST CIRCUIT PIN CONNECTIONS VCC (Bottom View) (Top View) 3 C3 L = 1000 nH 6 50 Ω C2 C1 1 IN 1000 pF 4 2, 3, 5 2 50 Ω OUT 1 1000 pF 1. 2. 3. 4. 5. 6. C1D 1000 pF 4 4 3 5 5 2 6 6 1 INPUT GND GND OUTPUT GND VCC Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 09/21/2000 DATA SUBJECT TO CHANGE WITHOUT NOTICE 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.