DATA SHEET MOS INTEGRATED CIRCUIT µPD444016 4M-BIT CMOS FAST SRAM 256K-WORD BY 16-BIT Description The µPD444016 is a high speed, low power, 4,194,304 bits (262,144 words by 16 bits) CMOS static RAM. Operating supply voltage is 5.0 V ± 0.5 V. The µPD444016 is packaged in 44-pin plastic SOJ and 44-pin plastic TSOP (II). Features • 262,144 words by 16 bits organization • Fast access time : 8, 10, 12 ns (MAX.) • Byte data control : /LB (I/O1 - I/O8), /UB (I/O9 - I/O16) • Output Enable input for easy application • Single +5.0 V power supply Ordering Information Part number Package Access time Supply current mA (MAX.) ns (MAX.) At operating At standby 10 µPD444016LE-8 44-pin plastic SOJ 8 220 µPD444016LE-10 (10.16 mm (400)) 10 200 12 190 µPD444016LE-12 µPD444016G5-8-7JF 44-pin plastic TSOP (II) 8 220 µPD444016G5-10-7JF (10.16 mm (400)) 10 200 µPD444016G5-12-7JF (Normal bent) 12 190 The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. M14430EJ4V0DS00 (4th edition) Date Published January 2001 NS CP(K) Printed in Japan The mark • shows major revised points. © 1999 µPD444016 Pin Configuration (Marking Side) /××× indicates active low signal. 44-pin plastic SOJ (10.16 mm (400)) [ µPD444016LE ] 44-pin plastic TSOP (II) (10.16 mm (400)) (Normal bent) [ µPD444016G5-×× ] ××-7JF ×× A0 1 44 A17 A1 2 43 A16 A2 3 42 A15 A3 4 41 /OE A4 5 40 /UB /CS 6 39 /LB I/O1 7 38 I/O16 I/O2 8 37 I/O15 I/O3 9 36 I/O14 I/O4 10 35 I/O13 VCC 11 34 GND GND 12 33 VCC I/O5 13 32 I/O12 I/O6 14 31 I/O11 I/O7 15 30 I/O10 I/O8 16 29 I/O9 /WE 17 28 NC A5 18 27 A14 A6 19 26 A13 A7 20 25 A12 A8 21 24 A11 A9 22 23 A10 A0 - A17 : Address Inputs I/O1 - I/O16 : Data Inputs / Outputs /CS : Chip Select /WE : Write Enable /OE : Output Enable /LB, /UB : Byte data select VCC : Power supply GND : Ground NC : No connection Remark Refer to Package Drawings for the 1-pin index mark. 2 Data Sheet M14430EJ4V0DS µPD444016 A0 | A17 I/O1 - I/O8 Row decoder Address buffer Block Diagram Memory cell array 4,194,304 bits Input data controller Sense amplifier / Switching circuit I/O9 - I/O16 Output data controller Column decoder /WE /CS /LB Address buffer /UB /OE VCC GND Truth Table /CS /OE /WE /LB /UB Mode I/O Supply current I/O1 - I/O8 I/O9 - I/O16 H × × × × Not selected High impedance High impedance ISB L L H L L Read DOUT DOUT ICC L H DOUT High impedance H L High impedance DOUT L L DIN DIN L H DIN High impedance H L High impedance DIN High impedance High impedance High impedance High impedance L × L L H H × × L × × H H Write Output disable Remark × : Don’t care Data Sheet M14430EJ4V0DS 3 µPD444016 Electrical Specifications Absolute Maximum Ratings Parameter Symbol Condition Rating –0.5 Note Unit Supply voltage VCC to +7.0 V Input / Output voltage VT –0.5 Note to VCC+0.5 V Operating ambient temperature TA 0 to 70 °C Storage temperature Tstg –55 to +125 °C Note –2.0 V (MIN.) (pulse width : 2 ns) Caution Exposing the device to stress above those listed in Absolute Maximum Rating could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Condition MIN. TYP. MAX. Unit 5.0 5.5 V VCC+0.5 V +0.8 V 70 °C Supply voltage VCC 4.5 High level input voltage VIH 2.2 Low level input voltage VIL –0.5 Operating ambient temperature TA 0 Note –2.0 V (MIN.) (pulse width : 2 ns) 4 Data Sheet M14430EJ4V0DS Note µPD444016 DC Characteristics (Recommended Operating Conditions Unless Otherwise Noted) Parameter Symbol Test condition MIN. TYP. MAX. Unit Input leakage current ILI VIN = 0 V to VCC –2 +2 µA Output leakage current ILO VI/O = 0 V to VCC, /CS = VIH or /OE = VIH –2 +2 µA mA or /WE = VIL or /LB = VIH or /UB = VIH Operating supply current Standby supply current ICC /CS = VIL, Cycle time : 8 ns 220 II/O = 0 mA, Cycle time : 10 ns 200 Minimum cycle time Cycle time : 12 ns 190 ISB /CS = VIH, VIN = VIH or VIL 40 ISB1 /CS ≥ VCC – 0.2 V, 10 mA VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V High level output voltage VOH IOH = –4.0 mA Low level output voltage VOL IOL = +8.0 mA 2.4 V 0.4 V MAX. Unit Remarks 1. VIN : Input voltage VI/O : Input / Output voltage 2. These DC characteristics are in common regardless of package types. Capacitance (TA = 25 °C, f = 1 MHz) Parameter Symbol Test condition MIN. TYP. Input capacitance CIN VIN = 0 V 6 pF Input / Output capacitance CI/O VI/O = 0 V 8 pF Remarks 1. VIN : Input voltage VI/O : Input / Output voltage 2. These parameters are periodically sampled and not 100% tested. Data Sheet M14430EJ4V0DS 5 µPD444016 AC Characteristics (Recommended Operating Conditions Unless Otherwise Noted) AC Test Conditions Input Waveform (Rise and Fall Time ≤ 3 ns) 3.0 V 1.5 V Test Points 1.5 V 1.5 V Test Points 1.5 V GND Output Waveform Output Load AC characteristics directed with the note should be measured with the output load shown in Figure 1 or Figure 2. Figure 1 Figure 2 (tAA, tACS, tOE, tABD, tOH) (tCLZ, tOLZ, tBLZ, tCHZ, tOHZ, tBHZ, tWHZ, tOW ) VTT = +1.5 V +5.0 V 50 Ω 480 Ω ZO = 50 Ω I/O (Output) I/O (Output) 30 pF CL 255 Ω Remark CL includes capacitances of the probe and jig, and stray capacitances. 6 Data Sheet M14430EJ4V0DS 5 pF CL µPD444016 Read Cycle Parameter µPD444016-8 Symbol MIN. MAX. 8 µPD444016-10 µPD444016-12 MIN. MIN. MAX. 10 Unit Notes MAX. Read cycle time tRC 12 ns Address access time tAA 8 10 12 ns /CS access time tACS 8 10 12 ns /OE access time tOE 4 5 6 ns /LB, /UB access time tABD 4 5 6 ns Output hold from address change tOH 3 3 3 ns /CS to output in low impedance tCLZ 3 3 3 ns /OE to output in low impedance tOLZ 0 0 0 ns /LB, /UB to output in low impedance tBLZ 0 0 0 ns /CS to output in high impedance tCHZ 4 5 6 ns /OE to output hold in high impedance tOHZ 4 5 6 ns /LB, /UB to output hold in high impedance tBHZ 4 5 6 ns 1 2, 3 Notes 1. See the output load shown in Figure 1. 2. Transition is measured at ± 200 mV from steady-state voltage with the output load shown in Figure 2. 3. These parameters are periodically sampled and not 100% tested. Remark These AC characteristics are in common regardless of package types. Read Cycle Timing Chart 1 (Address Access) tRC Address (Input) tAA tOH I/O (Output) Previous data out Data out Remarks 1. In read cycle, /WE should be fixed to high level. 2. /CS = /OE = /LB (or /UB) = VIL Data Sheet M14430EJ4V0DS 7 µPD444016 Read Cycle Timing Chart 2 (/CS Access) tRC Address (Input) tAA tACS /CS (Input) tCLZ tCHZ /OE (Input) tOE tOHZ tOLZ /LB, /UB (Input) tABD tBHZ tBLZ I/O (Output) High impedance Data out Caution Address valid prior to or coincident with /CS low level input. Remark In read cycle, /WE should be fixed to high level. 8 Data Sheet M14430EJ4V0DS High impedance µPD444016 Write Cycle Parameter Symbol µPD444016-8 MIN. MAX. µPD444016-10 µPD444016-12 MIN. MIN. MAX. Unit MAX. Write cycle time tWC 8 10 12 ns /CS to end of write tCW 6 7 8 ns Address valid to end of write tAW 6 7 8 ns Write pulse width tWP 6 7 8 ns /LB, /UB to end of write tBW 6 7 8 ns Data valid to end of write tDW 4 5 6 ns Data hold time tDH 0 0 0 ns Address setup time tAS 0 0 0 ns Write recovery time tWR 0 0 0 ns /WE to output in high impedance tWHZ Output active from end of write tOW 4 3 5 6 3 3 Notes ns 1, 2 ns Notes 1. Transition is measured at ± 200 mV from steady-state voltage with the output load shown in Figure 2. 2. These parameters are periodically sampled and not 100% tested. Remark These AC characteristics are in common regardless of package types. Write Cycle Timing Chart 1 (/WE Controlled) tWC Address (Input) tCW /CS (Input) tAW tAS tWR tWP /WE (Input) tBW /LB, /UB (Input) tOW tWHZ I/O (Input / Output) Indefinite data out tDW High impedance tDH Data in High impedance Indefinite data out Cautions 1. /CS or /WE should be fixed to high level during address transition. 2. Do not input data to the I/O pins while they are in the output state. Remarks 1. Write operation is done during the overlap time of a low level /CS, a low level /WE and a low level /LB (or low level /UB). 2. When /WE is at low level, the I/O pins are always high impedance. When /WE is at high level, read operation is executed. Therefore /OE should be at high level to make the I/O pins high impedance. Data Sheet M14430EJ4V0DS 9 µPD444016 Write Cycle Timing Chart 2 (/CS Controlled) tWC Address (Input) tAS tCW /CS (Input) tAW tWP tWR /WE (Input) tBW /LB, /UB (Input) tDW High impedance Data in I/O (Input) tDH High impedance Cautions 1. /CS or /WE should be fixed to high level during address transition. 2. Do not input data to the I/O pins while they are in the output state. Remark Write operation is done during the overlap time of a low level /CS, a low level /WE and a low level /LB (or low level /UB). 10 Data Sheet M14430EJ4V0DS µPD444016 Write Cycle Timing Chart 3 (/LB, /UB Controlled) tWC Address (Input) tAW tCW tWR /CS (Input) tWP /WE (Input) tAS tBW /LB, /UB (Input) tDW High impedance Data in I/O (Input) tDH High impedance Cautions 1. /CS or /WE should be fixed to high level during address transition. 2. Do not input data to the I/O pins while they are in the output state. Remark Write operation is done during the overlap time of a low level /CS, a low level /WE and a low level /LB (or low level /UB). Data Sheet M14430EJ4V0DS 11 µPD444016 Package Drawings 44-PIN PLASTIC SOJ (10.16 mm (400)) B 44 23 C 1 D 22 G J E F S U P M N Q M S K I H NOTE Each lead centerline is located within 0.12 mm of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS B 28.73 +0.20 −0.35 C 10.16 D 11.18±0.20 E 1.03±0.15 F 0.74 G 3.5±0.2 H 2.3±0.2 I J 0.8 MIN. 2.6 K 1.27 (T.P.) M 0.40±0.10 N P 0.12 Q 9.4±0.20 0.10 T R 0.85 U 0.20 +0.10 −0.05 P44LE-400A-1 12 Data Sheet M14430EJ4V0DS T µPD444016 44-PIN PLASTIC TSOP (II) (10.16 mm (400)) 44 23 detail of lead end F P E 1 22 A H G I S C D N M M J L S B K NOTE Each lead centerline is located within 0.13 mm of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS A 18.63 MAX. B 0.93 MAX. C 0.8 (T.P.) D 0.32 +0.08 −0.07 E 0.1±0.05 F 1.2 MAX. G 0.97 11.76±0.2 10.16±0.1 H I J 0.8±0.2 K 0.145+0.025 −0.015 L M 0.5±0.1 0.13 N 0.10 P +7° 3°−3° S44G5-80-7JF5-1 Data Sheet M14430EJ4V0DS 13 µPD444016 Recommended Soldering Conditions Please consult with our sales offices for soldering conditions of the µPD444016. Types of Surface Mount Device µPD444016LE : 44-pin plastic SOJ (10.16 mm (400)) µPD444016G5-7JF : 44-pin plastic TSOP (II) (10.16 mm (400)) (Normal bent) 14 Data Sheet M14430EJ4V0DS µPD444016 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to V DD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. Data Sheet M14430EJ4V0DS 15 µPD444016 • The information in this document is current as of January, 2001. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4