ALUMINUM ELECTROLYTIC CAPACITORS WP 5.5mmL Chip Type, Bi-Polarized series Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WP Smaller ZP Specifications Item Performance Characteristics Category Temperature Range – 40 ~ +85°C Rated Voltage Range 6.3 ~ 50V Rated Capacitance Range 0.1 ~ 100µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ 6.3 0.24 Rated voltage (V) tan δ (MAX.) 10 0.20 16 0.17 25 0.17 35 0.15 50 0.15 Measurement frequency : 120Hz Stability at Low Temperature 6.3 4 8 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C After 1000 hours' application of rated voltage at 85°C with the polarity inverted every 250 hours, capacitors meet the characteristic requirements listed at right. Endurance 10 3 6 16 2 4 25 2 4 35 2 3 50 2 3 Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Capacitance change tan δ Leakage current After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Initial specified value or less Leakage current listed at right. Shelf Life Resistance to soldering heat Marking Black print on the case top. Type numbering system (Example : 16V 10µF) 5.4 Voltage mark for 6.3V is C±0.2 B±0.2 φD±0.5 X2 10 16V Plastic platform 0.3 MAX. 1 3 4 5 6 7 8 9 10 11 12 13 14 Taping code Configuration Capacitance tolerance (±20%) +0.1 –0.2 φD 6V . 2 UWP 1 C 1 0 0 M C L 1 G B A±0.2 A±0.2 Voltage Lot No. E Capacitance 0.5 MAX. Chip Type 0.5 ~ 0.8 A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3 Rated Capacitance (10µF) Rated voltage (16V) Series name Type Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 5 6.3 6.3 8 10 1A 28 37 45 82 4 6.3 6.3 8 16 1C 17 33 41 61 4 5 6.3 6.3 8 25 1E 12 23 37 49 75 5 5 6.3 8 8 35 1V 12 16 27 50 61 4 5 5 6.3 8 50 1H 8.4 16 18 29 54 4 4 4 4 4 5 5 6.3 8 Case size φ D (mm) 1.0 2.0 2.8 4.0 8.4 13 17 20 36 Allowable ripple Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UN(p.77) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V