ALUMINUM ELECTROLYTIC CAPACITORS WS Chip Type, High CV High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type higher capacitance in large case size. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WS High Temperature Reflow UR Specifications Item Performance Characteristics – 40 ~ +85°C 6.3 ~ 50V 22 ~ 1500µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (µA) . Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage (V) tan δ (MAX.) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.14 50 0.12 Measurement frequency: 120Hz 6.3 5 10 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 35 2 3 25 2 4 16 3 6 10 4 8 50 2 3 Within ±20% of initial value 200% or less of initial specified value Initial specified value or less Capacitance change tan δ Leakage current Endurance After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Shelf Life After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Resistance to soldering heat The capacitors shall be kept on the hot plate maintained at 250°C, for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Marking Black print on the case top. 1 (φ6.3, φ8 × 6.2) 1 Size φ8 × 6.2 only 5 6 7 8 9 10 11 12 13 14 Package code Configuration Capacitance tolerance (–20%) Rated Capacitance (100µF) A±0.2 L±0.3 Capacitance 4 A±0.2 B±0.2 φD±0.5 N2 100A WS Series Positive C±0.2 3 0.5MAX. Plastic platform 0.3MAX. 2 UWS 1 A 1 0 1 M C L 1G S E Voltage (A:10V) Lot No. Within ±10% of initial value Initial specified value or less Initial specified value or less Type numbering system (Example : 10V 100µF) Chip Type 1 Trade mark Capacitance change tan δ Leakage current H Rated voltage (10V) Series name Negative Type (mm) φD×L (φ8 × 10, φ10 × 10) A±0.2 A B C E L H 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 2.4 6.6 6.6 2.2 5.8 0.5 ~ 0.8 2.4 6.6 6.6 2.2 7.7 0.5 ~ 0.8 3.3 8.3 8.3 2.3 6.2 0.5 ~ 0.8 2.9 8.3 8.3 3.1 10 0.8 ~ 1.1 3.2 10.3 10.3 4.5 10 0.8 ~ 1.1 A±0.2 L±0.5 Capacitance Lot No. C±0.2 B±0.2 Trade mark φD±0.5 N2 100V WS Series E Voltage (V:35V) 0.5MAX. Positive Plastic platform 0.3MAX. 6.3 × 5.8 Negative H Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WS series Dimensions V Cap. (µF) Code 6.3 10 16 25 35 50 0J 1A 1C 1E 1V 1H 6.3 × 5.8 22 220 33 330 47 470 100 101 6.3 × 5.8 70 8 × 6.2 150 151 6.3 × 5.8 85 6.3 × 7.7 220 221 8 × 6.2 160 8 × 6.2 175 330 331 8 × 6.2 190 8 × 10 470 471 8 × 10 265 680 681 8 × 10 318 1000 102 10 × 10 400 10 × 10 454 1500 152 10 × 10 489 45 6.3 × 5.8 55 8 × 6.2 95 6.3 × 5.8 65 8 × 6.2 105 8 × 10 140 125 8 × 6.2 145 8 × 10 175 10 × 10 195 151 8 × 10 192 8 × 10 214 10 × 10 238 8 × 10 215 10 × 10 250 10 × 10 265 10 × 10 289 240 8 × 10 270 10 × 10 305 10 × 10 324 8 × 10 290 10 × 10 330 10 × 10 393 10 × 10 374 10 × 10 396 Case size φ D × L (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Cap.(µF) Frequency 00 ~ 47V 100 ~ 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz~ 1.67 1.30 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V