Revised November 1998 74ACTQ16240 16-Bit Inverting Buffer/Line Driver with 3-STATE Outputs General Description Features The ACTQ16240 contains sixteen inverting buffers with 3STATE outputs designed to be employed as a memory and address driver, clock driver, or bus-oriented transmitter/ receiver. The device is nibble controlled. Each nibble has separate 3-STATE control inputs which can be shorted together for full 16-bit operation. ■ Utilizes Fairchild’s FACT Quiet Series technology The ACTQ16240 utilizes Fairchild’s Quiet Series technology to guarantee quiet output switching and improve dynamic threshold performance. FACT Quiet Series features GTO output control for superior performance. ■ 16-bit version of the ACTQ240 ■ Guaranteed simultaneous switching noise level and dynamic threshold performance ■ Guaranteed pin-to-pin output skew ■ Separate control logic for each byte ■ Outputs source/sink 24 mA ■ Additional specs for multiple output switching ■ Output loading specs for both 50 pF and 250 pF loads Ordering Code: Order Number Package Number 74ACTQ16240SSC MS48A 48-Lead Small Shrink Outline Package (SSOP), JEDEC MO-118, 0.300” Wide Package Description 74ACTQ16240MTD MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Logic Symbol Connection Diagram Pin Assignment for SSOP and TSSOP Pin Descriptions Pin Names Description OEn Output Enable Inputs (Active Low) I0–I15 Inputs O0–O15 Outputs FACT, FACT Quiet Series, Quiet Series, and GTO are trademarks of Fairchild Semiconductor Corporation. © 1999 Fairchild Semiconductor Corporation DS010924.prf www.fairchildsemi.com 74ACTQ16240 16-Bit Inverting Buffer/Line Driver with 3-STATE Outputs May 1991 74ACTQ16240 Truth Tables Functional Description Inputs I0–I3 O0–O3 L L H L H L H X Z OE1 Inputs Outputs OE2 I4–I7 O4–O7 L L H L H L H X Z Inputs Logic Diagram Outputs I8–I11 O8–O11 L L H L H L H X Z OE4 I12–I15 O12–O15 L L H L H L H X Z OE3 The ACTQ16240 contains sixteen inverting buffers with 3STATE standard outputs. The device is nibble (4 bits) controlled with each nibble functioning identically, but independently of the other. The control pins may be shorted together to obtain full 16-bit operation. The 3-STATE outputs are controlled by an Output Enable (OEn) input for each nibble. When OEn is LOW, the outputs are in 2-state mode. When OEn is HIGH, the outputs are in the high impedance mode, but this does not interfere with entering new data into the inputs. Outputs Inputs Outputs H = High Voltage Level L = Low Voltage Level X = Immaterial Z = High Impedance www.fairchildsemi.com 2 Recommended Operating Conditions −0.5V to +7.0V Supply Voltage (VCC) DC Input Diode Current (IIK) VI = −0.5V −20 mA VI = VCC + 0.5V +20 mA Supply Voltage (VCC) DC Output Diode Current (IOK) VO = −0.5V −20 mA VO = VCC + 0.5V +20 mA DC Output Voltage (VO) +140°C −65°C to +150°C 125 mV/ns VCC @ 4.5V, 5.5V Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT circuits outside databook specifications. ± 50 mA Storage Temperature −40°C to +85°C VIN from 0.8V to 2.0V DC VCC or Ground Current per Output Pin 0V to VCC Operating Temperature (TA) ± 50 mA Junction Temperature 0V to VCC Output Voltage (VO) Minimum Input Edge Rate (∆V/∆t) −0.5V to VCC + 0.5V DC Output Source/Sink Current (IO) 4.5V to 5.5V Input Voltage (VI) DC Electrical Characteristics Symbol Parameter TA = −40°C to +85°C TA = +25°C VCC (V) Typ Minimum High 4.5 1.5 2.0 2.0 Input Voltage 5.5 1.5 2.0 2.0 VIL Maximum Low 4.5 1.5 0.8 0.8 Input Voltage 5.5 1.5 0.8 0.8 VOH Minimum High 4.5 4.49 4.4 4.4 Output Voltage 5.5 5.49 5.4 5.4 3.86 3.76 VIH Units Conditions Guaranteed Limits V VOUT = 0.1V V VOUT = 0.1V V IOUT = −50 µA V IOH = −24 mA V IOUT = 50 µA V IOL = 24 mA or VCC − 0.1V or VCC − 0.1V VIN = VIL or VIH 4.5 5.5 VOL 4.86 4.76 Maximum Low 4.5 0.001 0.1 0.1 Output Voltage 5.5 0.001 0.1 0.1 4.5 0.36 0.44 IOH = −24 mA (Note 2) VIN = VIL or VIH IOZ Maximum 3-STATE IOL = 24 mA (Note 2) 5.5 0.36 0.44 5.5 ±0.5 ±5.0 µA VI = VIL, VIH 5.5 ± 0.1 ± 1.0 µA VI = VCC, GND 1.5 mA VI = VCC − 2.1V 8.0 80.0 µA VIN = VCC or GND 75 mA VOLD = 1.65V Max −75 mA VOHD = 3.85V Min VO = VCC, GND Leakage Current IIN Maximum Input Leakage Current ICCT Maximum ICC/Input 5.5 ICC Max Quiescent Supply Current 5.5 IOLD Minimum Dynamic 5.5 IOHD Output Current (Note 3) VOLP Quiet Output 0.6 5.0 0.5 0.8 V Maximum Dynamic VOL Figure 1Figure 2 (Note 5)(Note 6) VOLV Quiet Output Minimum Dynamic VOL 5.0 −0.5 −1.0 V Figure 1Figure 2 (Note 5)(Note 6) VOHP Maximum Overshoot 5.0 VOH + 1.0 VOH + 1.5 V Figure 1Figure 2 (Note 4)(Note 6) VOHV Minimum VCC Droop 5.0 VOH − 1.0 VOH − 1.8 V Figure 1Figure 2 (Note 4)(Note 6) VIHD Minimum High Dynamic Input Voltage Level 5.0 1.7 2.0 V (Note 4)(Note 7) VILD Maximum Low Dynamic Input Voltage Level 5.0 1.2 0.8 V (Note 4)(Note 7) Note 2: All outputs loaded; thresholds associated with output under test. Note 3: Maximum test duration 2.0 ms; one output loaded at a time. Note 4: Worst case package. Note 5: Maximum number of outputs that can switch simultaneously is n. (n − 1) outputs are switched LOW and one output held LOW. Note 6: Maximum number of outputs that can switch simultaneously is n. (n − 1) outputs are switched HIGH and one output held HIGH. Note 7: Maximum number of data inputs (n) switching. (n − 1) input switching 0V to 3V. Input under test switching 3V to threshold (VILD). 3 www.fairchildsemi.com 74ACTQ16240 Absolute Maximum Ratings(Note 1) 74ACTQ16240 AC Electrical Characteristics Symbol Parameter tPLH Propagation Delay tPHL Data to Output tPZH Output Enable Time VCC TA = +25°C (V) CL = 50 pF Min Typ Max Min Max 5.0 2.7 4.8 7.3 2.7 7.8 3.0 5.1 7.3 3.0 7.8 5.0 Output Disable Time CL = 50 pF (Note 8) tPZL tPHZ TA = −40°C to +85°C 5.0 tPLZ 2.5 4.5 7.4 2.5 7.9 2.7 4.7 7.5 2.7 8.0 2.3 5.0 7.9 2.3 8.2 2.0 4.6 7.4 2.0 7.9 Units ns ns ns Note 8: Voltage Range 5.0 is 5.0V ±0.5V. Extended AC Electrical Characteristics TA = −40°C to +85°C VCC = Com Symbol Parameter TA = −40°C to +85°C CL = 50 pF VCC = Com 16 Outputs Switching CL = 250 pF (Note 10) (Note 11) Max Min Max tPLH Propagation Delay Min 4.0 11.2 5.6 13.8 tPHL Data to Output 4.0 10.0 5.6 13.6 tPZH Output Enable Time tPZL tPHZ Output Disable Time tPLZ tOSHL Pin to Pin Skew (Note 9) HL Data to Output tOSLH Pin to Pin Skew (Note 9) LH Data to Output tOST Pin to Pin Skew (Note 9) LH/HL Data to Output Typ 3.5 10.1 3.4 10.0 3.6 8.9 3.1 8.1 Units ns (Note 12) ns (Note 13) ns 1.2 ns 2.5 ns 4.3 ns Note 9: Skew is defined as the absolute value of the difference between the actual propagation delays for any two separate outputs of the same device. The specification applies to any outputs switching HIGH to LOW (tOSHL), LOW to HIGH (tOSLH), or any combination switching LOW to HIGH and/or HIGH to LOW (tOST). Note 10: This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described switching in phase (i.e., all low-to-high, high-to-low, etc.). Note 11: This specification is guaranteed but not tested. The limits represent propagation delays with 250 pF load capacitors in place of the 50 pF load capacitors in the standard AC load. This specification pertains to single output switching only. Note 12: 3-STATE delays are load dominated and have been excluded from the datasheet. Note 13: The Output Disable Time is dominated by the RC network (500Ω, 250 pF) on the output and has been excluded from the datasheet. Capacitance Typ Units CIN Symbol Input Pin Capacitance Parameter 4.5 pF VCC = 5.0V CPD Power Dissipation Capacitance 30 pF VCC = 5.0V www.fairchildsemi.com 4 Conditions VOLP/VOLV and VOHP/VOHV: The setup of a noise characteristics measurement is critical to the accuracy and repeatability of the tests. The following is a brief description of the setup used to measure the noise characteristics of FACT. • Determine the quiet output pin that demonstrates the greatest noise levels. The worst case pin will usually be the furthest from the ground pin. Monitor the output voltages using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. Equipment: Hewlett Packard Model 8180A Word Generator PC-163A Test Fixture • Measure VOLP and VOLV on the quiet output during the worst case transition for active and enable. Measure VOHP and VOHV on the quiet output during the worst case active and enable transition. Tektronics Model 7854 Oscilloscope Procedure: 1. Verify Test Fixture Loading: Standard Load 50 pF, 500Ω. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. VILD and VIHD: 2. Deskew the HFS generator so that no two channels have greater than 150 ps skew between them. This requires that the oscilloscope be deskewed first. It is important to deskew the HFS generator channels before testing. This will ensure that the outputs switch simultaneously. • Monitor one of the switching outputs using a 50Ω coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. 3. Terminate all inputs and outputs to ensure proper loading of the outputs and that the input levels are at the correct voltage. • First increase the input LOW voltage level, VIL, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input LOW voltage level at which oscillation occurs is defined as VILD. 4. Set the HFS generator to toggle all but one output at a frequency of 1 MHz. Greater frequencies will increase DUT heating and affect the results of the measurement. • Next decrease the input HIGH voltage level on the, VIH, until the output begins to oscillate or steps out a mins of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input HIGH voltage level at which oscillation occurs is defined as VIHD. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. FIGURE 1. Quiet Output Noise Voltage Waveforms Note 14: VOHV and VOLP are measured with respect to ground reference. Note 15: Input pulses have the following characteristics: f = 1 MHz, tr = 3 ns, tf = 3 ns, skew < 150 ps. 5. Set the HFS generator input levels at 0V LOW and 3V HIGH for ACT devices and 0V LOW and 5V HIGH for AC devices. Verify levels with an oscilloscope. FIGURE 2. Simultaneous Switching Test Circuit 5 www.fairchildsemi.com 74ACTQ16240 FACT Noise Characteristics 74ACTQ16240 Physical Dimensions inches (millimeters) unless otherwise noted 48-Lead Small Shrink Outline Package (SSOP), JEDEC MO-118, 0.300” Wide Package Number MS48A www.fairchildsemi.com 6 48-Lead Think Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD48 LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or systems device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the sonably expected to cause the failure of the life support body, or (b) support or sustain life, and (c) whose failure device or system, or to affect its safety or effectiveness. to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the www.fairchildsemi.com user. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. 74ACTQ16240 16-Bit Inverting Buffer/Line Driver with 3-STATE Outputs Physical Dimensions inches (millimeters) unless otherwise noted (Continued)