Fractional-N/Integer-N PLL Synthesizer ADF4151 Data Sheet FEATURES GENERAL DESCRIPTION Fractional-N synthesizer and integer-N synthesizer RF bandwidth to 3.5 GHz 3.0 V to 3.6 V power supply 1.8 V logic compatibility Separate charge pump supply (VP) allows extended tuning voltage (up to 5.5 V) in 3 V systems Programmable dual-modulus prescaler of 4/5 or 8/9 Programmable RF output phase 3-wire serial interface Analog and digital lock detect Switched bandwidth fast lock mode Cycle slip reduction The ADF4151 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers if used with an external voltage controlled oscillator (VCO), loop filter, and external reference frequency. The ADF4151 is used with external VCO parts and is footprint and software compatible with the ADF4350. The part consists of a low noise digital phase frequency detector (PFD), a precision charge pump, and a programmable reference divider. There is a Σ-Δ based fractional interpolator to allow programmable fractional-N division. The INT, FRAC, and MOD registers define an overall N divider [N = (INT + (FRAC/MOD))]. The RF output phase is programmable for applications that require a particular phase relationship between the output and the reference. The ADF4151 also features cycle slip reduction circuitry, leading to faster lock times without the need for modifications to the loop filter. APPLICATIONS Wireless infrastructure (W-CDMA, TD-SCDMA, WiMax, GSM, PCS, DCS, DECT) Test equipment Wireless LANs, CATV equipment Clock generation Control of all the on-chip registers is through a simple 3-wire interface. The device operates with a power supply ranging from 3.0 V to 3.6 V that can be powered down when not in use. The ADF4151 is available in a 5 mm × 5 mm package. FUNCTIONAL BLOCK DIAGRAM SDVDD REFIN CLK DATA LE ×2 DOUBLER AVDDx 10-BIT R COUNTER DVDD VP RSET MULTIPLEXER ÷2 DIVIDER MUXOUT LOCK DETECT FLO SWITCH SW LD DATA REGISTER FUNCTION LATCH CHARGE PUMP CPOUT PHASE COMPARATOR INTEGER REG FRACTION REG MODULUS REG THIRD-ORDER FRACTIONAL INTERPOLATOR RFIN+ N COUNTER ADF4151 CE AGND CPGND SDGND DGND 10265-001 RFIN– Figure 1. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved. ADF4151 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Register 1 ..................................................................................... 17 Applications ....................................................................................... 1 Register 2 ..................................................................................... 17 General Description ......................................................................... 1 Register 3 ..................................................................................... 19 Functional Block Diagram .............................................................. 1 Register 4 ..................................................................................... 19 Revision History ............................................................................... 2 Register 5 ..................................................................................... 19 Specifications..................................................................................... 3 Initialization Sequence .............................................................. 19 Timing Characteristics ................................................................ 5 RF Synthesizer—A Worked Example ...................................... 20 Absolute Maximum Ratings ............................................................ 6 Modulus ....................................................................................... 20 Transistor Count ........................................................................... 6 Reference Doubler and Reference Divider ............................. 20 ESD Caution .................................................................................. 6 12-Bit Programmable Modulus ................................................ 20 Pin Configuration and Function Descriptions ............................. 7 Cycle Slip Reduction for Faster Lock Times ........................... 21 Typical Performance Characteristics ............................................. 9 Spurious Optimization and Fast lock ...................................... 21 Circuit Description ......................................................................... 11 Fast Lock Timer and Register Sequences ................................ 21 Reference Input Section ............................................................. 11 Fast Lock—An Example ............................................................ 22 RF N Divider ............................................................................... 11 Fast Lock—Loop Filter Topology............................................. 22 INT, FRAC, MOD, and R Counter Relationship.................... 11 Spur Mechanisms ....................................................................... 22 INT N Mode ................................................................................ 11 Spur Consistency and Fractional Spur Optimization ........... 23 R Counter .................................................................................... 11 Phase Resync ............................................................................... 23 Phase Frequency Detector (PFD) and Charge Pump ............ 11 Applications Information .............................................................. 24 MUXOUT and Lock Detect ...................................................... 12 Direct Conversion Modulator .................................................. 24 Input Shift Registers ................................................................... 12 Interfacing ................................................................................... 25 Program Modes .......................................................................... 12 PCB Design Guidelines for Chip Scale Package .................... 25 Register Maps .............................................................................. 13 Outline Dimensions ....................................................................... 26 Register 0 ..................................................................................... 17 Ordering Guide .......................................................................... 26 REVISION HISTORY 12/11—Rev. A to Rev. B Changes to Normalized 1/f Noise Parameter, Table 1 ................. 4 11/11—Rev. 0 to Rev. A Changes to Figure 28 ...................................................................... 23 10/11—Revision 0: Initial Version Rev. B | Page 2 of 28 Data Sheet ADF4151 SPECIFICATIONS AVDD = DVDD = SDVDD = 3.3 V ± 10%; VP = AVDD to 5.5 V; AGND = DGND = 0 V; TA = TMIN to TMAX, unless otherwise noted. Operating temperature range is −40°C to +85°C. Table 1. Parameter REFIN CHARACTERISTICS Input Frequency Input Sensitivity Input Capacitance Input Current RF INPUT CHARACTERISTICS RF Input Frequency (RFIN) Prescaler Output Frequency MAXIMUM PFD FREQUENCY Fractional-N Mode Low Spur Mode Low Noise Mode Integer-N Mode CHARGE PUMP ICP Sink/Source High Value Low Value RSET Range ICP Leakage Sink and Source Matching ICP vs. VCP ICP vs. Temperature LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINH/IINL Input Capacitance, CIN LOGIC OUTPUTS Output High Voltage, VOH Output High Current, IOH Output Low Voltage, VO POWER SUPPLIES AVDD DVDD, SDVDD VP DIDD + AIDD 2 VPIDD2 Low Power Sleep Mode Min B Version Typ 10 0.7 Max Unit Conditions/Comments 250 AVDD For f < 10 MHz, ensure slew rate > 21 V/µs Biased at AVDD/2 1 ±60 MHz V p-p pF µA 3.5 750 GHz MHz 26 32 32 MHz MHz MHz 10 0.5 For lower frequencies, ensure slew rate > 400 V/µs −10 dBm ≤ RF input power ≤ +5 dBm RSET = 5.1 kΩ 4.5 0.281 2.7 10 1 2 1.5 2 1.5 0.6 ±1 5.0 DVDD − 0.4 3.0 mA mA kΩ nA % % % VCP = VP/2 0.5 V ≤ VCP ≤ VP − 0.5 V 0.5 V ≤ VCP ≤ VP − 0.5 V VCP = VP/2 V V µA pF 500 0.4 V µA V 3.6 V 5.5 50 V mA mA µA CMOS output chosen IOL = 500 µA AVDD AVDD 40 2 1 Rev. B | Page 3 of 28 VP = 5 V ADF4151 Parameter NOISE CHARACTERISTICS Normalized In-Band Phase Noise Floor (PNSYNTH) 3 Normalized 1/f Noise (PN1_f) 4 Normalized In-Band Phase Noise Floor (PNSYNTH)3 Normalized 1/f Noise (PN1_f)4 Spurious Signals Due to PFD Frequency 5 Data Sheet Min B Version Typ Max Unit Conditions/Comments −221 dBc/Hz PLL loop BW = 500 kHz (ABP = 3 ns) −118 −220 dBc/Hz dBc/Hz −115 dBc/Hz −107 dBc 10 kHz offset. Normalized to 1 GHz (ABP = 3 ns) PLL loop BW = 500 kHz (ABP = 6 ns); low noise mode 10 kHz offset; normalized to 1 GHz (ABP = 6 ns); low noise mode PFD = 25 MHz AC coupling ensures AVDD/2 bias. TA = 25°C; AVDD = DVDD = 3.6 V; prescaler = 4/5; fREFIN = 130 MHz; fPFD = 26 MHz; fRF = 1.742 GHz. 3 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 log N (where N is the N divider value) and 10 log FPFD. PNSYNTH = PNTOT – 10 log fPFD – 20 log N 4 The PLL phase noise is composed of 1/f (flicker) noise plus the normalized PLL noise floor. The formula for calculating the 1/f noise contribution at an RF frequency (fRF) and at a frequency offset (f) is given by PN = P1_f + 10 log(10 kHz/f) + 20 log(fRF/1 GHz). Both the normalized phase noise floor and flicker noise are modeled in ADIsimPLL 5 Spurious measured on EVAL-ADF4151EB1Z with RF buffer between VCO output and RF input by-passed, using a Rohde & Schwarz FSUP signal source analyzer. 1 2 Rev. B | Page 4 of 28 Data Sheet ADF4151 TIMING CHARACTERISTICS AVDD1, AVDD2 = DVDD = SDVDD = 3.3 V ± 10%; VP = AVDD to 5.5 V; AGND = DGND = 0 V; TA = TMIN to TMAX, unless otherwise noted. Operating temperature range is −40°C to +85°C. Table 2. Parameter t1 t2 t3 t4 t5 t6 t7 Limit (B Version) 20 10 10 25 25 10 20 Unit ns min ns min ns min ns min ns min ns min ns min t4 Test Conditions/Comments LE setup time DATA to CLK setup time DATA to CLK hold time CLK high duration CLK low duration CLK to LE setup time LE pulse width t5 CLK t3 t2 DATA DB31 (MSB) DB30 DB2 (LSB) (CONTROL BIT C3) DB1 (LSB) (CONTROL BIT C2) DB0 (LSB) (CONTROL BIT C1) t7 LE t1 10265-002 t6 LE Figure 2. Timing Diagram Rev. B | Page 5 of 28 ADF4151 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 3. Parameter AVDD1, AVDD2 to GND1 AVDD1, AVDD2 to DVDD VP to AVDD1, AVDD2 Digital I/O Voltage to GND1 Analog I/O Voltage to GND1 REFIN to GND1 Operating Temperature Range Storage Temperature Range Maximum Junction Temperature LFCSP θJA Thermal Impedance (Paddle-Soldered) Reflow Soldering Peak Temperature Time at Peak Temperature 1 Rating −0.3 V to +3.9 V −0.3 V to +0.3 V −0.3 V to +5.8 V −0.3 V to VDD + 0.3 V −0.3 V to VDD + 0.3 V −0.3 V to VDD + 0.3 V −40°C to +85°C −65°C to +125°C 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. TRANSISTOR COUNT 36685 (CMOS) and 967 (bipolar) ESD CAUTION 27.3°C/W 260°C 40 sec GND = AGND = DGND = 0 V. Rev. B | Page 6 of 28 Data Sheet ADF4151 32 31 30 29 28 27 26 25 SDVDD SDGND MUXOUT REFIN DVDD DGND DGND LD PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 24 1 2 PIN 1 INDICATOR 3 23 22 4 ADF4151 21 5 TOP VIEW (Not to Scale) 20 6 19 7 18 8 17 NC NC RSET AGND NC NC AGND AVDD2 NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 2. THE LFCSP HAS AN EXPOSED PADDLE THAT MUST BE CONNECTED TO GND. 10265-003 AGND AVDD1 AGND NC NC RFIN+ RFIN− AVDD2 9 10 11 12 13 14 15 16 CLK DATA LE CE SW VP CPOUT CPGND Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic CLK 2 DATA 3 LE 4 CE 5 6 SW VP 7 CPOUT 8 9, 11, 18, 21 10 CPGND AGND 12, 13, 19, 20, 23, 24 14 15 NC 16, 17 AVDD2 AVDD1 RFIN+ RFIN− Description Serial Clock Input. Data is clocked into the 32-bit shift register on the CLK rising edge. This input is a high impedance CMOS input. Serial Data Input. The serial data is loaded, MSB first, with the three LSBs as the control bits. This input is a high impedance CMOS input. Load Enable, CMOS Input. When LE goes high, the data stored in the shift register is loaded into the register that is selected by the three LSBs. Chip Enable. A logic low on this pin powers down the device and puts the charge pump into three-state mode. Taking the pin high powers up the device depending on the status of the power-down bits. Fast Lock Switch. Make a connection to this pin from the loop filter when using the fast lock mode. Charge Pump Power Supply. This pin should be greater than or equal to AVDD. In systems where AVDDx is 3 V, it can be set to 5.5 V and used to drive a VCO with a tuning range of up to 5.5 V. Charge Pump Output. When enabled, this provides ±ICP to the external loop filter. The output of the loop filter is connected to VTUNE to drive the external VCO. Charge Pump Ground. This is the ground return pin for CPOUT. Analog Ground. This is a ground return pin for AVDD1 and AVDD2. Analog Power Supply. This pin ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane are to be placed as close as possible to this pin. AVDD must have the same value as DVDD. No connect. Do not connect to this pin. Input to the RF Input. This small signal input is ac-coupled to the external VCO. Complementary Input to the RF Input. This pin must be decoupled to the ground plane with a small bypass capacitor, typically 100 pF. Analog Power Supply. This pin ranges from 3.0 V to 3.6 V. Decoupling capacitors to the analog ground plane are to be placed as close as possible to this pin. AVDDx must have the same value as DVDD. Rev. B | Page 7 of 28 ADF4151 Pin No. 22 Mnemonic RSET Data Sheet Description Connecting a resistor between this pin and GND sets the charge pump output current. The nominal voltage bias at the RSET pin is 0.49 V. The relationship between ICP and RSET is I CP = 25 LD 26, 27 28 DGND DVDD 29 REFIN 30 MUXOUT 31 32 SDGND SDVDD EP 22.95 RSET where: RSET = 5.1 kΩ. ICP = 4.5 mA. Lock Detect Output Pin. This pin outputs a logic high to indicate PLL lock; a logic low output indicates loss of PLL lock. Digital Ground. Ground return path for DVDD. Digital Power Supply. This pin should be the same voltage as AVDD. Decoupling capacitors to the ground plane should be placed as close as possible to this pin. Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and a dc equivalent input resistance of 100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled. Multiplexer Output. This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference frequency to be accessed externally. Digital Sigma-Delta (Σ-Δ) Modulator Ground. Ground return path for the Σ-Δ modulator. Power Supply Pin for the Digital Σ-Δ Modulator. Should be the same voltage as AVDDx. Decoupling capacitors to the ground plane are to be placed as close as possible to this pin. The exposed pad must be connected to GND. Rev. B | Page 8 of 28 Data Sheet ADF4151 TYPICAL PERFORMANCE CHARACTERISTICS 0 –90 +85°C +25°C –40°C –5 LOW SPUR MODE –91 –92 PHASE NOISE (dBc/Hz) POWER (dBm) –10 –15 –20 –25 –30 –93 –94 –95 –96 LOW NOISE MODE –97 –98 –35 1.0 1.5 2.0 2.5 3.0 3.5 4.0 FREQUENCY (GHz) ICP MISMATCH (%) 1.13mA 0.56mA 0.56mA 1.13mA 2.25mA 4.5mA SOURCE 0.5 1.0 1.5 2.0 2.5 VCP (V) SINK 3.0 3.5 4.0 4.5 5.0 10265-005 ICP (mA) 2.25mA 0 2.63 2.64 2.65 2.66 2.67 2.68 2.69 2.70 Figure 6. In-Band Phase Noise Measured at 10 kHz Offset for Low Noise Mode and Low Spur Mode, PFD = 25 MHz, PLL Loop Bandwidth = 50 kHz 4.5mA 0.28mA 0.28mA 2.62 FREQUENCY (GHz) Figure 4. RF Input Sensitivity 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 –3.5 –4.0 –4.5 –5.0 –5.5 –6.0 2.61 Figure 5. Charge Pump Output Characteristics, VP = 5 V, Selected ICP Values Between 0.28 mA (Min) and 4.5 mA (Max), RSET = 5.1 kΩ 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 –3.5 –4.0 –4.5 –5.0 –5.5 –6.0 ICP ICP ICP ICP ICP 0 0.5 1.0 1.5 2.0 = 0.28mA = 0.56mA = 1.13mA = 2.25mA = 4.5mA 2.5 VCP (V) 3.0 3.5 4.0 4.5 5.0 10265-007 0.5 10265-004 0 –100 2.60 10265-006 –99 –40 Figure 7. Charge Pump Output Mismatch vs. VCP , Selected ICP Values Between 0.28 mA (Min) and 4.5 mA (Max), RSET = 5.1 kΩ Rev. B | Page 9 of 28 Data Sheet –60 –60 –80 –80 PHASE NOISE (dBc/Hz) –100 –120 –140 –160 –100 –120 –140 10k 100k 1M 10M FREQUENCY OFFSET (Hz) –180 1k 10265-008 –80 –80 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) –60 –100 –120 –140 10M –100 –120 –140 –160 –160 100k 1M 10M –180 1k 10265-009 10k FREQUENCY OFFSET (Hz) Figure 9. Fractional-N Phase Noise and Spur Performance; Low Noise Mode; VCOOUT = 1755.2 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth = 50 kHz, Channel Spacing = 200 kHz, FRAC = 26, MOD = 125 –60 –80 –80 –120 –140 100k 1M 10M Figure 12. Fractional-N Phase Noise and Spur Performance; Low Noise Mode; VCOOUT = 905.2 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth= 20 kHz, Channel Spacing = 200 kHz, FRAC = 26, MOD = 125 –60 –100 10k FREQUENCY OFFSET (Hz) PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) 1M Figure 11. Integer-N Phase Noise and Spur Performance; Low Noise Mode; VCOOUT = 900 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth = 20 kHz –60 –160 –100 –120 –140 –160 10k 100k 1M FREQUENCY OFFSET (Hz) 10M –180 1k 10265-010 –180 1k 100k FREQUENCY OFFSET (Hz) Figure 8. Integer-N Phase Noise and Spur Performance; Low Noise Mode; VCOOUT = 1750 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth = 50 kHz –180 1k 10k 10265-012 –180 1k 10265-011 –160 Figure 10. Fractional-N Phase Noise and Spur Performance; Low Spur Mode; VCOOUT = 1755.2 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth = 50 kHz, Channel Spacing = 200 kHz, FRAC = 26, MOD = 125 10k 100k 1M FREQUENCY OFFSET (Hz) 10M 10265-013 PHASE NOISE (dBc/Hz) ADF4151 Figure 13. Fractional-N Phase Noise and Spur Performance; Low Spur Mode; VCOOUT = 905.2 MHz, REFIN = 100 MHz, PFD = 25 MHz, Loop Filter Bandwidth = 20 kHz, Channel Spacing = 200 kHz, FRAC = 26, MOD = 125 Rev. B | Page 10 of 28 Data Sheet ADF4151 CIRCUIT DESCRIPTION REFERENCE INPUT SECTION N = INT + FRAC/MOD RF N DIVIDER The reference input stage is shown in Figure 14. SW1 and SW2 are normally closed switches. SW3 is normally open. When power-down is initiated, SW3 is closed and SW1 and SW2 are opened. This ensures that there is no loading of the REFIN pin on power-down. FROM VCO OUTPUT/ OUTPUT DIVIDERS TO PFD N COUNTER THIRD-ORDER FRACTIONAL INTERPOLATOR POWER-DOWN CONTROL MOD REG FRAC VALUE 10265-015 INT REG 100kΩ NC SW2 REFIN NC TO R COUNTER Figure 15. RF INT Divider BUFFER SW1 INT N MODE 10265-014 SW3 NO The RF N divider allows a division ratio in the PLL feedback path. Division ratio is determined by the INT, FRAC, and MOD values, which build up this divider. If the FRAC = 0 and DB8 in Register 2 (LDF) is set to 1, the synthesizer operates in integer-N mode. The DB8 in Register 2 (LDF) should be set to 1 to get integer-N digital lock detect. Additionally, lower phase noise is possible if the antibacklash pulse width is reduced to 3 ns. This mode is not valid for fractional-N applications. INT, FRAC, MOD, AND R COUNTER RELATIONSHIP R COUNTER The INT, FRAC, and MOD values, in conjunction with the R counter, make it possible to generate output frequencies that are spaced by fractions of the PFD frequency. See the RF Synthesizer—A Worked Example section for more information. The RF VCO frequency (RFOUT) equation is The 10-bit R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 1023 are allowed. Figure 14. Reference Input Stage RF N DIVIDER (1) where: RFOUT is the output frequency of the external voltage controlled oscillator (VCO). INT is the preset divide ratio of the binary 16-bit counter (23 to 32,767 for 4/5 prescaler, 75 to 65,535 for 8/9 prescaler). FRAC is the numerator of the fractional division (0 to MOD − 1). MOD is the preset fractional modulus (2 to 4095 for low noise mode, 50 to 4095 for low spur mode). fPFD = REFIN × [(1 + D)/(R × (1 + T))] The phase frequency detector (PFD) takes inputs from the R counter and N counter and produces an output proportional to the phase and frequency difference between them. Figure 16 is a simplified schematic of the phase frequency detector. The PFD includes a programmable delay element that sets the width of the antibacklash pulse, which can be either 6 ns (default, for fractional-N applications) or 3 ns (for integer-N mode). This pulse ensures that there is no dead zone in the PFD transfer function and gives a consistent reference spur level. (2) where: REFIN is the reference input frequency. D is the REFIN doubler bit. R is the preset divide ratio of the binary 10–bit programmable reference counter (1 to 1023). T is the REFIN divide-by-2 bit (0 or 1). HIGH D1 Q1 UP U1 +IN CLR1 DELAY HIGH U3 CHARGE PUMP CLR2 DOWN D2 Q2 U2 –IN Figure 16. PFD Simplified Schematic Rev. B | Page 11 of 28 CP 10265-016 RFOUT = fPFD × (INT + (FRAC/MOD)) PHASE FREQUENCY DETECTOR (PFD) AND CHARGE PUMP ADF4151 Data Sheet MUXOUT AND LOCK DETECT shift register. There are three LSBs: DB2, DB1, and DB0, as shown in Figure 2. The truth table for these bits is shown in Table 5. Figure 18 shows a summary of how the latches are programmed. The output multiplexer on the ADF4151 allows the user to access various internal points on the chip. The state of MUXOUT is controlled by M3, M2, and M1 (for details, see Figure 21). Figure 17 shows the MUXOUT section in block diagram form. Table 5. C3, C2, and C1 Truth Table R COUNTER INPUT C3 0 0 0 0 1 1 DVDD THREE-STATE-OUTPUT DVDD DGND R COUNTER OUTPUT MUX CONTROL MUXOUT N COUNTER OUTPUT Control Bits C2 0 0 1 1 0 0 C1 0 1 0 1 0 1 Register Register 0 (R0) Register 1 (R1) Register 2 (R2) Register 3 (R3) Register 4 (R4) Register 5 (R5) PROGRAM MODES ANALOG LOCK DETECT DIGITAL LOCK DETECT Figure 19 through Figure 24 show how the program modes are to be set up in the ADF4151. 10265-017 RESERVED DGND Figure 17. MUXOUT Schematic INPUT SHIFT REGISTERS The ADF4151 digital section includes a 10-bit RF R counter, a 16-bit RF N counter, a 12-bit FRAC counter, and a 12-bit modulus counter. Data is clocked into the 32-bit shift register on each rising edge of CLK. The data is clocked in MSB first. Data is transferred from the shift register to one of six latches on the rising edge of LE. The destination latch is determined by the state of the three control bits (C3, C2, and C1) in the A number of settings in the ADF4151 are double buffered. These include the modulus value, phase value, R counter value, reference doubler, reference divide-by-2, and current setting. This means that two events must occur before the part uses a new value of any of the double-buffered settings. First, the new value is latched into the device by writing to the appropriate register. Second, a new write must be performed on Register R0. For example, any time the modulus value is updated, Register R0 must be written to, thus ensuring that the modulus value is loaded correctly. Rev. B | Page 12 of 28 Data Sheet ADF4151 REGISTER MAPS RESERVED REGISTER 0 16-BIT INTEGER VALUE (INT) CONTROL BITS 12-BIT FRACTIONAL VALUE (FRAC) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 N16 N15 N14 N13 N12 N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1 F12 F11 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 DB2 DB1 DB0 C3(0) C2(0) C1(0) RESERVED PRESCALER PHASE ADJUST REGISTER 1 DBR1 12-BIT PHASE VALUE (PHASE) CONTROL BITS DBR 1 12-BIT MODULUS VALUE (MOD) P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 M12 M11 M10 M9 M8 M7 DB2 DB1 DB0 M6 M5 M4 M3 M2 M1 C3(0) C2(0) C1(1) COUNTER RESET PR1 CP THREESTATE PH1 POWER-DOWN 0 PD POLARITY 0 LDF 0 LDP DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 CONTROL BITS DBR 1 10-BIT R COUNTER RESERVED MUXOUT RDIV2 LOW NOISE AND LOW SPUR MODES REFERENCE DOUBLER DBR 1 RESERVED REGISTER 2 DBR 1 CHARGE PUMP CURRENT SETTING DBR 1 DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 L2 L1 M3 M2 M1 RD2 RD1 R10 R9 R8 R7 R6 R5 R4 R3 R2 R1 0 CP4 CP3 CP2 CP1 U6 U5 U4 U3 U2 U1 DB2 DB1 DB0 C3(0) C2(1) C1(0) RESERVED RESERVED CSR ABP RESERVED CHARGE CANCEL REGISTER 3 CLK DIV MODE CONTROL BITS 12-BIT CLOCK DIVIDER VALUE DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 0 0 0 0 0 0 0 0 F3 F2 0 0 F1 0 C2 C1 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 DB2 DB1 DB0 C3(0) C2(1) C1(1) REGISTER 4 CONTROL BITS RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DB2 DB1 DB0 C3(1) C2(0) C1(0) REGISTER 5 CONTROL BITS RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 1 DBR 0 0 0 0 0 0 0 D15 D14 0 0 0 0 0 0 0 0 0 = DOUBLE BUFFERED REGISTER—BUFFERED BY THE WRITE TO REGISTER 0. Figure 18. Register Summary Rev. B | Page 13 of 28 0 0 0 0 0 0 0 0 0 0 DB2 DB1 DB0 C3(1) C2(0) C1(1) 10265-018 LD PIN MODE RESERVED Data Sheet RESERVED ADF4151 16-BIT INTEGER VALUE (INT) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 N16 N15 N14 N13 N12 N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1 F12 F11 F10 F9 F8 F7 F6 DB7 DB6 F5 F4 DB5 DB4 F3 F2 DB3 F1 DB2 N16 N15 ... N5 N4 N3 N2 N1 INTEGER VALUE (INT) F12 F11 .......... F2 F1 FRACTIONAL VALUE (FRAC) 0 0 ... 0 0 0 0 0 NOT ALLOWED 0 0 .......... 0 0 0 0 0 ... 0 0 0 0 1 NOT ALLOWED 0 0 .......... 0 1 1 0 0 ... 0 0 0 1 0 NOT ALLOWED 0 0 .......... 1 0 2 . . ... . . . . . ... 0 0 .......... 1 1 3 0 0 ... 1 0 1 1 0 NOT ALLOWED . . .......... . . . 0 0 ... 1 0 1 1 1 23 . . .......... . . . 0 0 ... 1 1 0 0 0 24 . . .......... . . . . . ... . . . . . ... 1 1 .......... 0 0 4092 1 1 ... 1 1 1 0 1 65533 1 1 .......... 0 1 4093 1 1 ... 1 1 1 1 0 65534 1 1 .......... 1 0 4094 1 1 ... 1 1 1 1 1 65535 1 1 ......... 1 1 4095 DB1 DB0 C3(0) C2(0) C1(0) 10265-019 0 CONTROL BITS 12-BIT FRACTIONAL VALUE (FRAC) INTmin = 75 WITH PRESCALER = 8/9 RESERVED PRESCALER PHASE ADJUST Figure 19. Register 0 (R0) DBR 12-BIT PHASE VALUE (PHASE) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 PH1 1 OFF ON P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 M12 M11 M10 M9 M8 M7 M6 DB7 DB6 M5 M4 P1 PRESCALER P12 P11 .......... P2 P1 PHASE VALUE (PHASE) M12 M11 .......... M2 M1 0 4/5 0 0 .......... 0 0 0 0 0 .......... 1 0 2 1 8/9 0 0 .......... 0 1 1 (RECOMMENDED) 0 0 .......... 1 1 3 0 0 .......... 1 0 2 . . .......... . . . 0 0 .......... 1 1 3 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 4092 . . .......... . . . 1 1 .......... 0 1 4093 . . .......... . . . 1 1 .......... 1 0 4094 1 1 .......... 0 0 4092 1 1 .......... 1 1 4095 1 1 .......... 0 1 4093 1 1 .......... 1 0 4094 1 1 .......... 1 1 4095 PH1 PHASE ADJUST 0 PR1 DB5 DB4 M3 M2 DB3 M1 DB2 DB1 DB0 C3(0) C2(0) C1(1) INTERPOLATOR MODULUS (MOD) 10265-020 0 CONTROL BITS DBR 12-BIT MODULUS VALUE (MOD) Figure 20. Register 1 (R1) Rev. B | Page 14 of 28 COUNTER RESET CP THREESTATE POWER-DOWN LDP DBR CHARGE PUMP CURRENT SETTING LDF DBR 10-BIT R COUNTER RESERVED MUXOUT RDIV2 LOW NOISE AND LOW SPUR MODES PD POLARITY ADF4151 REFERENCE DOUBLER DBR RESERVED Data Sheet DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 L2 L1 M3 M2 M1 RD2 RD1 R10 R9 R8 R7 R6 R5 R4 R3 R2 R1 0 CP4 CP3 CP2 CP1 U6 U5 U4 U3 U2 U1 CONTROL BITS DB2 DB1 RD2 REFERENCE DOUBLER U6 LDF U1 COUNTER RESET LOW NOISE MODE 0 DISABLED 0 FRAC-N 0 DISABLED 1 RESERVED 1 ENABLED 1 INT-N 1 ENABLED 1 0 RESERVED 1 1 LOW SPUR MODE L2 NOISE MODE 0 0 0 RD1 R10 REFERENCE DIVIDE BY 2 0 DISABLED CP4 CP3 CP2 CP1 ICP (mA) 5.1kΩ 1 ENABLED 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0.28 0.56 0.84 1.13 1.41 1.69 1.97 2.25 2.53 2.81 3.09 3.38 3.66 3.94 4.22 4.5 R9 .......... R2 R1 0 0 .......... 0 1 1 0 0 .......... 1 0 2 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 1020 1 1 .......... 0 1 1021 1 1 .......... 1 0 1022 1 1 .......... 1 1 1023 M3 M2 M1 OUTPUT 0 0 0 THREE-STATE OUTPUT 0 0 1 DVDD 0 1 0 DGND 0 1 1 R DIVIDER OUTPUT 1 0 0 N DIVIDER OUTPUT 1 0 1 ANALOG LOCK DETECT 1 1 0 DIGITAL LOCK DETECT 1 1 1 RESERVED R DIVIDER (R) CP THREE-STATE U5 LDP U2 0 10ns 0 DISABLED 1 6ns 1 ENABLED U4 PD POLARITY U3 POWER-DOWN 0 NEGATIVE 0 DISABLED 1 POSITIVE 1 ENABLED 10265-021 L1 DB0 C3(0) C2(1) C1(0) Figure 21. Register 2 (R2) Rev. B | Page 15 of 28 RESERVED CSR CHARGE CANCEL RESERVED RESERVED Data Sheet ABP ADF4151 CLK DIV MODE DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 0 0 0 0 0 F3 F2 0 0 F1 C2 C1 D12 D11 D10 D9 D8 D7 D6 DB7 DB6 D5 CYCLE SLIP REDUCTION D12 D11 .......... D2 D1 0 0 .......... 0 0 0 0 DISABLED 0 0 .......... 0 1 1 1 ENABLED 0 0 .......... 1 0 2 0 0 .......... 1 1 3 . . .......... . . . . . .......... . . . . . .......... . . . 1 1 .......... 0 0 4092 F1 F2 0 CONTROL BITS 12-BIT CLOCK DIVIDER VALUE D4 DB5 DB4 D3 D2 DB3 D1 DB2 DB1 DB0 C3(0) C2(1) C1(1) CLOCK DIVIDER VALUE C2 C1 CLOCK DIVIDER MODE 0 0 CLOCK DIVIDER OFF 0 1 FAST LOCK ENABLE 1 1 .......... 0 1 4093 1 0 RESYNC ENABLE 1 1 .......... 1 0 4094 1 1 RESERVED 1 1 .......... 1 1 4095 CHARGE CANCELLATION 0 DISABLED 1 ENABLED 0 6ns (FRAC-N) 1 3ns (INT_N) 10265-022 ANTIBACKLASH PULSE WIDTH F3 Figure 22. Register 3 (R3) DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DB2 DB1 DB0 C3(1) C2(0) C1(0) 10265-023 CONTROL BITS RESERVED Figure 23. Register 4 (R4) LD PIN MODE RESERVED CONTROL BITS RESERVED DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 0 0 0 0 0 0 0 D15 D14 0 0 D1 5 D1 4 LOCK DETECT PIN OPERATION 0 0 LOW 0 1 DIGITAL LOCK DETECT 1 0 LOW 1 1 HIGH 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DB5 DB4 0 0 DB3 0 DB2 DB1 DB0 C3(1) C2(0) C1(1) 10265-024 0 DB7 DB6 Figure 24. Register 5 (R5) Rev. B | Page 16 of 28 Data Sheet ADF4151 REGISTER 0 12-Bit Phase Value (PHASE) Control Bits These bits control what is loaded as the phase word. The word must be less than the MOD value programmed in Register 1. The word is used to program the RF output phase from 0° to 360° with a resolution of 360°/MOD. See the Phase Resync section for more information. In most applications, the phase relationship between the RF signal and the reference is not important. In such applications, the phase value can be used to optimize the fractional and subfractional spur levels. See the Spur Consistency and Fractional Spur Optimization section for more information. With Bits[C3:C1] set to 0, 0, 0, Register 0 is programmed. Figure 19 shows the input data format for programming this register. 16-Bit Integer Value (INT) These 16 bits set the INT value, which determines the integer part of the feedback division factor. They are used in Equation 1 (see the INT, FRAC, MOD, and R Counter Relationship section). All integer values from 23 to 32,767 are allowed for 4/5 prescaler. For 8/9 prescaler, the minimum integer value is 75, and the maximum value is 65,535. 12-Bit Fractional Value (FRAC) The 12 FRAC bits set the numerator of the fraction that is input to the Σ-Δ modulator. This, along with INT, specifies the new frequency channel that the synthesizer locks to, as shown in the RF Synthesizer—A Worked Example section. FRAC values from 0 to MOD − 1 cover channels over a frequency range equal to the PFD reference frequency. REGISTER 1 This programmable register sets the fractional modulus. This is the ratio of the PFD frequency to the channel step resolution on the RF output. See the RF Synthesizer—A Worked Example section for more information. REGISTER 2 With Bits[C3:C1] set to 0, 1, 0, Register 2 is programmed. Figure 21 shows the input data format for programming this register. With Bits[C3:C1] set to 0, 0, 1, Register 1 is programmed. Figure 20 shows the input data format for programming this register. Low Noise and Spur Modes Phase Adjust The noise modes on the ADF4151 are controlled by DB30 and DB29 in Register 2 (see Figure 21). The noise modes allow the user to optimize a design either for improved spurious performance or for improved phase noise performance. The phase adjust bit, enabled by programming a 1 to DB28, permits adjustments to the output phase of a given output frequency. If enabled, it does not perform a phase resync function on updating R0. If set to 0, the phase resync (if enabled in R3, Bits[DB16:DB15]) occurs on every update of R0. Prescaler Value The dual modulus prescaler (P/P + 1), along with the INT, FRAC, and MOD counters, determines the overall division ratio from the VCO output to the PFD input. Operating at CML levels, it takes the clock from the VCO output and divides it down for the counters. It is based on a synchronous 4/5 core. When set to 4/5, the maximum RF frequency allowed is 3 GHz. Therefore, when operating the ADF4151 above 3 GHz, this must be set to 8/9. The prescaler limits the INT value, where: In the ADF4151, PR1 in Register 1 sets the prescaler values. 12-Bit Modulus Value (MOD) Control Bits Control Bits P = 4/5, NMIN = 23 P = 8/9, NMIN = 75 If neither the phase resync nor the spurious optimization functions are being used, it is recommended that the phase word be set to 1. When the lowest spur setting is chosen, dither is enabled. This randomizes the fractional quantization noise so it resembles white noise rather than spurious noise. As a result, the part is optimized for improved spurious performance. This operation would normally be used when the PLL closed-loop bandwidth is wide, for fast locking applications. (Wide-loop bandwidth is seen as a loop bandwidth greater than 1/10 of the RFOUT channel step resolution (fRES)). A wide loop filter does not attenuate the spurs to the same level as a narrow-loop bandwidth. For best noise performance, use the lowest noise setting option. As well as disabling the dither, it also ensures that the charge pump is operating in an optimum region for noise performance. This setting is extremely useful where a narrow-loop filter bandwidth is available. The synthesizer ensures extremely low noise, and the filter attenuates the spurs. The typical performance characteristics give the user an idea of the trade-off in a typical W-CDMA setup for the different noise and spur settings. Rev. B | Page 17 of 28 ADF4151 Data Sheet MUXOUT Lock Detect Precision (LDP) The on-chip multiplexer is controlled by Bits[DB28:DB26] (see Figure 21). When DB7 is set to 0, the fractional-N digital lock detect is activated. In this case after setting DB7 to 0, 40 consecutive PFD cycles of 10 ns must occur before digital lock detect is set. When DB7 is programmed to 1, 40 consecutive reference cycles of 6 ns must occur before digital lock detect goes high. Setting DB8 (LDF) to 1 causes the activation of the integer-N digital lock detect. In this case, after setting DB7 (LDP) to 0, five consecutive cycles of 10 ns must occur before digital lock detect is set. When DB7 is set to 1, five consecutive cycles of 6 ns must occur. Recommended settings of both the LDP and LDF bits are shown in Table 6. Reference Doubler Setting DB25 to 0 feeds the REFIN signal directly to the 10-bit R counter, disabling the doubler. Setting this bit to 1 multiplies the REFIN frequency by a factor of 2 before feeding into the 10-bit R counter. When the doubler is disabled, the REFIN falling edge is the active edge at the PFD input to the fractional synthesizer. When the doubler is enabled, both the rising and falling edges of REFIN become active edges at the PFD input. When the doubler is enabled and the lowest spur mode is chosen, the in-band phase noise performance is sensitive to the REFIN duty cycle. The phase noise degradation can be as much as 5 dB for the REFIN duty cycles outside a 45% to 55% range. The phase noise is insensitive to the REFIN duty cycle in the lowest noise mode. The phase noise is insensitive to the REFIN duty cycle when the doubler is disabled. When the doubler is enabled, the maximum allowable REFIN frequency is 30 MHz. RDIV2 Setting the DB24 bit to 1 inserts a divide-by-2 toggle flip-flop between the R counter and PFD, which extends the maximum REFIN input rate. This function allows a 50% duty cycle signal to appear at the PFD input, which is necessary for cycle slip reduction. 10-Bit R Counter The 10-bit R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 1023 are allowed. Current Setting Bits[DB12:DB9] set the charge pump current setting. This should be set to the charge pump current that the loop filter is designed with (see Figure 21). LDF Setting DB8 to 1 enables integer-N digital lock detect, when the FRAC part of the divider is zero; setting DB8 to 0 enables fractional-N digital lock detect. Table 6. Recommended LDF/LDP Bit Settings Mode Integer-N Fractional-N Low Noise Mode Fractional-N Low Spur Mode DB8 (LDF) 1 0 0 DB7 (LDP) 1 1 0 Phase Detector Polarity DB6 sets the phase detector polarity. When a passive loop filter or noninverting active loop filter is used, set this bit to 1. If an active filter with an inverting characteristic is used, this bit should be set to 0. Power-Down (PD) DB5 provides the programmable power-down mode. Setting this bit to 1 performs a power-down. Setting this bit to 0 returns the synthesizer to normal operation. When in software power-down mode, the part retains all information in its registers. Only if the supply voltages are removed are the register contents lost. When a power-down is activated, the following events occur: • • • • • The synthesizer counters are forced to their load state conditions. The charge pump is forced into three-state mode. The digital lock detect circuitry is reset. The RFOUT buffers are disabled. The input register remains active and capable of loading and latching data. Charge Pump (CP) Three-State DB4 puts the charge pump into three-state mode when programmed to 1. It should be set to 0 for normal operation. Counter Reset DB3 is the R counter and N counter reset bit for the ADF4151. When this bit is 1, the RF synthesizer N counter and R counter are held in reset. For normal operation, this bit should be set to 0. Rev. B | Page 18 of 28 Data Sheet ADF4151 REGISTER 3 REGISTER 4 Control Bits Control Bits With Bits[C3:C1] set to 0, 1, 1, Register 3 is programmed. Figure 22 shows the input data format for programming this register. With Bits[C3: C1] set to 1, 0, 0, Register 4 is programmed. Figure 23 shows the input data format for programming this register. Antibacklash Pulse Width This register is reserved and has to be programmed with the values as shown in Figure 23. Bits[DB31:DB24] and [DB22:DB3] must be programmed to 0, while Bit DB23 must be set to 1. Setting DB22 to 0 sets the PFD antibacklash pulse width to 6 ns. This is the recommended mode for fractional-N use. By setting this bit to 1, the 3 ns pulse width is used and results in a phase noise and spur improvement in integer-N operation. For fractional-N mode it is not recommended to use this smaller setting. Charge Cancellation Mode Pulse Width Setting DB21 to 1 enables charge pump charge cancellation. This has the effect of reducing PFD spurs in integer-N mode. In fractional-N mode, this bit should not be used. This results in a phase noise and fractional spur improvement. REGISTER 5 Control Bits With Bits[C3:C1] set to 1, 0, 1, Register 5 is programmed. Figure 24 shows the input data form for programming this register. Lock Detect PIN Operation Bits[DB23:DB22] set the operation of the lock detect pin (see Figure 24). Cycle Slip Reduction (CSR) Enable INITIALIZATION SEQUENCE Setting DB18 to 1 enables cycle slip reduction. This is a method for improving lock times. Note that the signal at the phase frequency detector (PFD) must have a 50% duty cycle for cycle slip reduction to work. The charge pump current setting must also be set to a minimum. See the Cycle Slip Reduction for Faster Lock Times section for more information. The following sequence of registers is the correct sequence for initial power up of the ADF4151 after the correct application of voltages to the supply pins: Clock Divider Mode Bits[DB16:DB15] must be set to 1, 0 to activate phase resync or 0, 1 to activate fast lock. Setting Bits[DB16:DB15] to 0, 0 disables the clock divider. See Figure 22. 1. 2. 3. 4. 5. 6. 12-Bit Clock Divider Value The 12-bit clock divider value sets the timeout counter for activation of phase resync. See the Phase Resync section for more information. It also sets the timeout counter for fast lock. See the Fast Lock Timer and Register Sequences section for more information. Rev. B | Page 19 of 28 Register 5 Register 4 Register 3 Register 2 Register 1 Register 0 ADF4151 Data Sheet RF SYNTHESIZER—A WORKED EXAMPLE MODULUS The following is an example of how to program the ADF4151 synthesizer: The choice of modulus (MOD) depends on the reference signal (REFIN) available and the channel resolution (fRES) required at the RF output. For example, a GSM system with 13 MHz REFIN sets the modulus to 65. This means that the RF output resolution (fRES) is the 200 kHz (13 MHz/65) necessary for GSM. With dither off, the fractional spur interval depends on the modulus values chosen (see Table 7). RFOUT = [INT + (FRAC/MOD)] × [fPFD]/RF Divider (3) where: RFOUT is the RF frequency output. INT is the integer division factor. FRAC is the fractionality. MOD is the modulus. RF Divider is the output divider that divides down the VCO frequency. fPFD = REFIN × [(1 + D)/(R × (1 + T))] (4) where: REFIN is the reference frequency input. D is the RF REFIN doubler bit. R is the RF reference division factor. T is the reference divide-by-2 bit (0 or 1). 12-BIT PROGRAMMABLE MODULUS Unlike most other fractional-N PLLs, the ADF4151 allows the user to program the modulus over a 12-bit range. This means that the user can set up the part in many different configurations for the application, when combined with the reference doubler and the 10-bit R counter. fPFD RFOUT N DIVIDER 10265-025 VCO Figure 25. Loop Closed Before Output Divider A channel resolution (fRES) of 200 kHz is required at the output of the VCO. MOD = REFIN/fRES MOD = 10 MHz/200 kHz = 50 From Equation 4 fPFD = [10 MHz × (1 + 0)/1] = 10 MHz (5) 2112.6 MHz = 10 MHz × (INT + FRAC/50) (6) where: INT = 211 FRAC = 13 The reference doubler on chip allows the input reference signal to be doubled. This is useful for increasing the PFD comparison frequency. Making the PFD frequency higher improves the noise performance of the system. Doubling the PFD frequency usually improves noise performance by 3 dB. It is important to note that the PFD cannot operate above maximum value (see Table 1) due to a limitation in the speed of the Σ-Δ circuit of the N-divider. The reference divide-by-2 divides the reference signal by 2, resulting in a 50% duty cycle PFD frequency. This is necessary for the correct operation of the cycle slip reduction (CSR) function. See the Cycle Slip Reduction for Faster Lock Times section for more information. For example, in a UMTS system, where 2112.6 MHz RF frequency output (RFOUT) is required, a 10 MHz reference frequency input (REFIN) is available, and a 200 kHz channel resolution (fRESOUT) is required on the RF output. A 2.1 GHz VCO is suitable to cover the required fractional frequency of 2112.6 MHz. PFD REFERENCE DOUBLER AND REFERENCE DIVIDER For example, consider an application that requires 1.75 GHz RF and 200 kHz channel step resolution. The system has a 13 MHz reference signal. One possible setup is feeding the 13 MHz directly to the PFD and programming the modulus to divide by 65. This results in the required 200 kHz resolution. Another possible setup is using the reference doubler to create 26 MHz from the 13 MHz input signal. The 26 MHz is then fed into the PFD, programming the modulus to divide by 130. This also results in 200 kHz resolution and offers superior phase noise performance over the previous setup. The programmable modulus is also very useful for multistandard applications. If a dual-mode phone requires PDC and GSM 1800 standards, the programmable modulus is a great benefit. PDC requires 25 kHz channel step resolution, whereas GSM 1800 requires 200 kHz channel step resolution. Rev. B | Page 20 of 28 Data Sheet ADF4151 A 13 MHz reference signal can be fed directly to the PFD, and the modulus can be programmed to 520 when in PDC mode (13 MHz/520 = 25 kHz). The modulus needs to be reprogrammed to 65 for GSM 1800 operation (13 MHz/65 = 200 kHz). It is important that the PFD frequency remain constant (13 MHz). This allows the user to design one loop filter for both setups without running into stability issues. It is important to remember that the ratio of the RF frequency to the PFD frequency principally affects the loop filter design, not the actual channel spacing. CYCLE SLIP REDUCTION FOR FASTER LOCK TIMES As outlined in the Low Noise and Spur Mode section, the ADF4151 contains a number of features that allow optimization for noise performance. However, in fast locking applications, the loop bandwidth generally needs to be wide, and, therefore, the filter does not provide much attenuation of the spurs. If the cycle slip reduction feature is enabled, the narrow-loop bandwidth is maintained for spur attenuation but faster lock times are still possible. Cycle Slips If the phase error increases again to a point where another cycle slip is likely, the ADF4151 turns on another charge pump cell. This continues until the ADF4151 detects that the VCO frequency has gone past the desired frequency. The extra charge pump cells are turned off one by one until all the extra charge pump cells have been disabled and the frequency is settled with the original loop filter bandwidth. Up to seven extra charge pump cells can be turned on. In most applications, it is enough to eliminate cycle slips altogether, giving much faster lock times. Setting Bit DB18 in the Register 3 to 1 enables cycle slip reduction. Note that the PFD requires a 45% to 55% duty cycle for CSR to operate correctly. SPURIOUS OPTIMIZATION AND FAST LOCK Narrow-loop bandwidths can filter unwanted spurious signals, but these usually have a long lock time. A wider loop bandwidth achieves faster lock times, but a wider loop bandwidth may lead to increased spurious signals inside the loop bandwidth. The fast lock feature can achieve the same fast lock time as the wider bandwidth, but with the advantage of a narrow final loop bandwidth to keep spurs low. Cycle slips occur in integer-N/fractional-N synthesizers when the loop bandwidth is narrow compared to the PFD frequency. The phase error at the PFD inputs accumulates too fast for the PLL to correct, and the charge pump temporarily pumps in the wrong direction. This slows down the lock time dramatically. The ADF4151 contains a cycle slip reduction feature that extends the linear range of the PFD, allowing faster lock times without modifications to the loop filter circuitry. FAST LOCK TIMER AND REGISTER SEQUENCES When the circuitry detects that a cycle slip is about to occur, it turns on an extra charge pump current cell. This outputs a constant current to the loop filter or removes a constant current from the loop filter (depending on whether the VCO tuning voltage needs to increase or decrease to acquire the new frequency). The effect is that the linear range of the PFD is increased. Loop stability is maintained because the current is constant and is not a pulsed current. 1. If the fast lock mode is used, a timer value must be loaded into the PLL to determine the duration of the wide bandwidth mode. When Bits[DB16:DB15] in Register 3 are set to 0, 1 (fast lock enable), the timer value is loaded by the 12-bit clock divider value. The following sequence must be programmed to use fast lock: 2. Rev. B | Page 21 of 28 Initialization sequence (see the Initialization Sequence section); occurs only once after powering up the part. Load Register 3 by setting Bits[DB16:DB15] to 0, 1 and the chosen fast lock timer value, Bits[DB14:DB3]. Note that the length of time the PLL remains in wide bandwidth is equal to the fast lock timer/fPFD. ADF4151 Data Sheet FAST LOCK—AN EXAMPLE SPUR MECHANISMS If a PLL has a reference frequency of 13 MHz, a fPFD of 13 MHz and a required lock time of 50 µs, the PLL is set to wide bandwidth for 40 µs. This example assumes a modulus of 65 for channel spacing of 200 kHz. This section describes the three different spur mechanisms that arise with a fractional-N synthesizer and how to minimize them in the ADF4151. If the time period set for the wide bandwidth is 40 µs, then The fractional interpolator in the ADF4151 is a third-order Σ-Δ modulator (SDM) with a modulus (MOD) that is programmable to any integer value from 2 to 4095. In low spur mode (dither enabled), the minimum allowable value of MOD is 50. The SDM is clocked at the PFD reference rate (fPFD) that allows PLL output frequencies to be synthesized at a channel step resolution of fPFD/MOD. Fast Lock Timer Value = Time In Wide Bandwidth × fPFD/MOD Fast Lock Timer Value = 40 µs × 13 MHz/65 = 8 Therefore, 8 must be loaded into the clock divider value in Register 3 in Step 1 of the sequence described in the Fast Lock Timer and Register Sequences section. FAST LOCK—LOOP FILTER TOPOLOGY To use fast lock mode, the damping resistor in the loop filter is reduced to ¼ of its value while in wide bandwidth mode. To achieve the wider loop filter bandwidth, the charge pump current increases by a factor of 16. To maintain loop stability, the damping resistor must be reduced a factor of ¼. To enable fast lock, the SW pin is shorted to the GND pin by setting Bits[DB16:DB15] in Register 3 to values 0, 1. The following two topologies are available: ADF4151 R2 CPOUT VCO C1 C3 C2 R1 SW Table 7. Fractional Spurs with Dither Off Condition (Dither Off) If MOD is divisible by 2, but not 3 If MOD is divisible by 3, but not 2 If MOD is divisible by 6 Otherwise Repeat Length 2 × MOD 3 × MOD 6 × MOD MOD Spur Interval Channel step/2 Channel step/3 Channel step/6 Channel step In low spur mode (dither on), the repeat length is extended to 221 cycles, regardless of the value of MOD, which makes the quantization error spectrum look like broadband noise. This may degrade the in-band phase noise at the PLL output by as much as 10 dB. For lowest noise, dither off is a better choice, particularly when the final loop bandwidth is low enough to attenuate even the lowest frequency fractional spur. Integer Boundary Spurs R1A 10265-026 • The damping resistor (R1) is divided into two values (R1 and R1A) that have a ratio of 1:3 (see Figure 26). An extra resistor (R1A) is connected directly from SW, as shown in Figure 27. The extra resistor is calculated such that the parallel combination of an extra resistor and the damping resistor (R1) is reduced to ¼ of the original value of R1 (see Figure 27). In low noise mode (dither off), the quantization noise from the Σ-Δ modulator appears as fractional spurs. The interval between spurs is fPFD/L, where L is the repeat length of the code sequence in the digital Σ-Δ modulator. For the third-order modulator used in the ADF4151, the repeat length depends on the value of MOD, as listed in Table 7. Figure 26. Fast Lock Loop Filter Topology—Topology 1 ADF4151 R2 CPOUT VCO C1 C2 R1A R1 C3 SW Another mechanism for fractional spur creation is the interactions between the RF VCO frequency and the reference frequency. When these frequencies are not integer related (the point of a fractional-N synthesizer) spur sidebands appear on the VCO output spectrum at an offset frequency that corresponds to the beat note or difference frequency between an integer multiple of the reference and the VCO frequency. These spurs are attenuated by the loop filter and are more noticeable on channels close to integer multiples of the reference where the difference frequency can be inside the loop bandwidth; therefore, the name integer boundary spurs. 10265-027 • Fractional Spurs Figure 27. Fast Lock Loop Filter Topology—Topology 2 Rev. B | Page 22 of 28 Data Sheet ADF4151 Reference Spurs Reference spurs are generally not a problem in fractional-N synthesizers because the reference offset is far outside the loop bandwidth. However, any reference feedthrough mechanism that bypasses the loop can cause a problem. Feedthrough of low levels of on-chip reference switching noise, through the RFIN pin back to the VCO, can result in reference spur levels as high as −90 dBc. PCB layout must ensure adequate isolation between VCO traces and the input reference to avoid a possible feedthrough path on the board. SPUR CONSISTENCY AND FRACTIONAL SPUR OPTIMIZATION With dither off, the fractional spur pattern due to the quantization noise of the SDM also depends on the particular phase word with which the modulator is seeded. The phase word can be varied to optimize the fractional and subfractional spur levels on any particular frequency. Thus, a look-up table of phase values corresponding to each frequency can be constructed for use when programming the ADF4151. If a look-up table is not used, keep the phase word at a constant value to ensure consistent spur levels on any particular frequency. PHASE RESYNC The output of a fractional-N PLL can settle to any one of the MOD phase offsets with respect to the input reference, where MOD is the fractional modulus. The phase resync feature in the ADF4151 produces a consistent output phase offset with respect to the input reference. This is necessary in applications where the output phase and frequency are important, such as digital beam forming. See the Phase Programmability section for how to program a specific RF output phase when using phase resync. Phase resync is enabled by setting Bit DB16, Bit DB15 in Register 3 to 1, 0. When phase resync is enabled, an internal timer generates sync signals at intervals of tSYNC given by the following formula: tSYNC = CLK_DIV_VALUE × MOD × tPFD where: CLK_DIV_VALUE is the decimal value programmed in Bits[DB14:DB3] of Register 3 and can be any integer in the range of 1 to 4095. MOD is the modulus value programmed in Bits[DB14:DB3] of Register 1 (R1). tPFD is the PFD reference period. When a new frequency is programmed, the second sync pulse after the LE rising edge is used to resynchronize the output phase to the reference. The tSYNC time must be programmed to a value that is at least as long as the worst-case lock time. This guarantees that the phase resync occurs after the last cycle slip in the PLL settling transient. In the example shown in Figure 28, the PFD reference is 25 MHz and MOD is 125 for a 200 kHz channel spacing. tSYNC is set to 400 µs by programming the clock divider value, CLK_DIV_VALUE, to 80. LE SYNC (INTERNAL) tSYNC LAST CYCLE SLIP FREQUENCY PLL SETTLES TO INCORRECT PHASE PLL SETTLES TO CORRECT PHASE AFTER RESYNC –100 0 100 200 300 400 500 600 TIME (µs) 700 800 900 1000 10265-028 PHASE Figure 28. Phase Resync Example Phase Programmability The phase word in Register 1 controls the RF output phase. As this word is swept from 0 to MOD, the RF output phase sweeps over a 360° range in steps of 360°/MOD. Rev. B | Page 23 of 28 ADF4151 Data Sheet APPLICATIONS INFORMATION DIRECT CONVERSION MODULATOR The LO ports of the ADL5375 can be driven from the VCO output. To ensure that all three RF ports (VCO output, RFIN and LOIP) are connected to 50 Ω impedance, the matching network of three 18 Ω resistors must be placed as in Figure 29. AC coupling of the RF signal is implemented by the capacitors connected in serial with the 18 Ω resistors . It is possible, as well, to use a balun to convert from a single-ended LO input to the differential LO inputs for the ADL5375. Direct conversion architectures are increasingly being used to implement base station transmitters. Figure 29 shows how Analog Devices, Inc., parts can be used to implement such a system. The circuit block diagram shows the AD9788 TxDAC® being used with the ADL5375. The use of dual integrated DACs, such as the AD9788 with its specified ±0.02 dB and ±0.004 dB gain and offset matching characteristics, ensures minimum error contribution (over temperature) from this portion of the signal chain. The signal for the I channel of the quadrature modulator is taken from the OUT1 differential outputs of the AD9788, and the OUT2 differential outputs provide the signal for the Q channel of the quadrature modulator ADL5375. If the I and Q inputs are driven in quadrature by 2 V p-p signals, the resulting output power from the modulator is approximately 2 dBm. The local oscillator (LO) is implemented using the ADF4151. The low-pass filter was designed using ADIsimPLL™ for a channel spacing of 200 kHz and a closed-loop bandwidth of 35 kHz. 51Ω REFIO 51Ω OUT1_P MODULATED DIGITAL DATA AD9788 LOW-PASS FILTER OUT1_N TxDAC OUT2_P LOW-PASS FILTER OUT2_N FSADJ 51Ω 51Ω 2kΩ VDD VP ADL5375 IBBP LOCK DETECT IBBN 10 16 AVDD1 AVDD2 17 AVDD2 4 28 32 6 CE DVDD SDV DD VP MUXOUT 1nF 1nF 51Ω 29 REF IN 1 CLK 2 DATA 3 LE LD 100pF RFIN+ 14 18Ω 18Ω 1nF LOIN 18Ω RFIN– 15 LOIP QUADRATURE PHASE SPLITTER RFOUT 1nF 100pF 100pF DSOP VVCO ADF4151 QBBP VCO OUT VCC QBBN VTUNE 22 RSET VCO 4.7kΩ 680Ω CPOUT 7 SW 5 39nF 2700pF CPGND AGND AGND AGND AGND DGND 8 9 11 18 21 26 1200pF 360Ω DGND SDGND 27 31 10265-029 SPI-COMPATIBLE SERIAL BUS FREF IN 25 30 Figure 29. Direct Conversion Modulator Rev. B | Page 24 of 28 Data Sheet ADF4151 INTERFACING Blackfin BF527 Interface The ADF4151 has a simple SPI-compatible serial interface for writing to the device. CLK, DATA, and LE control the data transfer. When LE goes high, the 32 bits that have been clocked into the appropriate register on each rising edge of CLK are transferred to the appropriate latch. See Figure 2 for the timing diagram and Table 5 for the register address table. Figure 31 shows the interface between the ADF4151 and the Blackfin ADSP-BF527 digital signal processor (DSP). The ADF4151 needs a 32-bit serial word for each latch write. The easiest way to accomplish this using the Blackfin family is to use the autobuffered transmit mode of operation with alternate framing. This provides a means for transmitting an entire block of serial data before an interrupt is generated. Set up the word length for eight bits and use four memory locations for each 32-bit word. To program each 32-bit latch, store the four 8-bit bytes, enable the autobuffered mode, and write to the transmit register of the DSP. This last operation initiates the autobuffer transfer. As in the microcontroller case, just make sure that the clock speeds are within the maximum limits outlined in Table 2. ADuC812 Interface Figure 30 shows the interface between the ADF4151 and the ADuC812 MicroConverter®. Because the ADuC812 is based on an 8051 core, this interface can be used with any 8051-based microcontroller. The MicroConverter is set up for SPI master mode with CPHA = 0. To initiate the operation, the I/O port driving LE is brought low. Each latch of the ADF4151 needs a 32-bit word, which is accomplished by writing four 8-bit bytes from the MicroConverter to the device. When the fourth byte has been written, the LE input should be brought high to complete the transfer. MOSI MOSI DATA LE CE I/O FLAGS MUXOUT (LOCK DETECT) CLK DATA LE I/O PORTS CLK 10265-031 SCLOCK SCLK GPIO ADF4151 ADuC812 ADF4151 ADSP-BF527 Figure 31. ADSP-BF527 to ADF4151 Interface CE PCB DESIGN GUIDELINES FOR CHIP SCALE PACKAGE 10265-030 MUXOUT (LOCK DETECT) Figure 30. ADuC812 to ADF4151 Interface I/O port lines on the ADuC812 are also used to control powerdown (CE input) and detect lock (MUXOUT configured as lock detect and polled by the port input). When operating in the described mode, the maximum SCLOCK rate of the ADuC812 is 4 MHz. This means that the maximum rate at which the output frequency can be changed is 125 kHz. The lands on the chip scale package (CP-32-7) are rectangular. The PCB pad for these must be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. The land is to be centered on the pad. This ensures that the solder joint size is maximized. The bottom of the chip scale package has a central thermal pad. The thermal pad on the PCB must be at least as large as the exposed pad. On the PCB, there is to be a minimum clearance of 0.25 mm between the thermal pad and the inner edges of the pad pattern. This ensures that shorting is avoided. Thermal vias can be used on the PCB thermal pad to improve the thermal performance of the package. If vias are used, they are to be incorporated in the thermal pad at 1.2 mm pitch grid. The via diameter must be between 0.3 mm and 0.33 mm, and the via barrel must be plated with one ounce copper to plug the via. Rev. B | Page 25 of 28 ADF4151 Data Sheet OUTLINE DIMENSIONS 0.30 0.25 0.18 32 25 0.50 BSC 1 24 TOP VIEW 0.80 0.75 0.70 8 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 3.25 3.10 SQ 2.95 EXPOSED PAD 17 0.50 0.40 0.30 PIN 1 INDICATOR 9 BOTTOM VIEW 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. 112408-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 Figure 32. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm × 5 mm Body, Very Thin Quad (CP-32-7) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADF4151BCPZ ADF4151BCPZ-RL7 EVAL-ADF4151EB1Z 1 Temperature Range −40°C to +85°C −40°C to +85°C Package Description 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] Evaluation Board Z = RoHS Compliant Part. Rev. B | Page 26 of 28 Package Option CP-32-7 CP-32-7 Data Sheet ADF4151 NOTES Rev. B | Page 27 of 28 ADF4151 Data Sheet NOTES ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10265-0-12/11(B) Rev. B | Page 28 of 28