IRF AUIRFR6215

AUTOMOTIVE GRADE
PD-96302
AUIRFR6215
HEXFET® Power MOSFET
Features
O
O
O
O
O
O
O
O
O
P-Channel
Low On-Resistance
Dynamic dV/dT Rating
175°C Operating Temperature
Fast Switching
Fully Avalanche Rated
Repetitive Avalanche Allowed up to Tjmax
Lead-Free, RoHS Compliant
Automotive Qualified *
V(BR)DSS
D
-150V
0.295:
RDS(on) max.
G
ID
S
-13A
D
Description
Specifically designed for Automotive applications of
HEXFET® Power MOSFETs utilizes the latest processing
techniques to achieve low on-resistance per silicon area.
This benefit combined with the fast switching speed and
ruggedized device design that HEXFET power MOSFETs
are well known for, provides the designer with an extremely
efficient and reliable device for use in Automotive and a
wide variety of other applications.
S
D
G
D-Pak
AUIRFR6215
G
D
S
Gate
Drain
Source
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are
stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in the
specifications is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions.
Ambient temperature (T A) is 25°C, unless otherwise specified.
Parameter
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
EAS
IAR
EAR
dv/dt
TJ
TSTG
Max.
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
Maximum Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy (Thermally limited)
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds (1.6mm from case)
ch
ch
e
dh
ch
Units
-13
-9.0
-44
110
0.71
± 20
310
-6.6
11
5.0
-55 to + 175
A
W
W/°C
V
mJ
A
mJ
V/ns
°C
300
Thermal Resistance
Parameter
hj
RθJC
Junction-to-Case
Junction-to-Ambient(PCB mount)
RθJA
RθJA
Junction-to-Ambient
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
www.irf.com
i
Typ.
Max.
Units
–––
–––
–––
1.4
50
110
°C/W
1
04/13/10
AUIRFR6215
Static Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
V(BR)DSS
Drain-to-Source Breakdown Voltage
∆V(BR)DSS/∆TJ Breakdown Voltage Temp. Coefficient
Min. Typ. Max. Units
-150
–––
–––
Conditions
VGS = 0V, ID = -250µA
c
f
= -6.6A f T = 150°C
–––
-0.20
–––
V/°C Reference to 25°C, ID = -1mA
–––
–––
0.295
VGS = -10V, ID = -6.6A
–––
–––
0.58
-2.0
–––
-4.0
V
S
RDS(on)
Static Drain-to-Source On-Resistance
VGS(th)
Gate Threshold Voltage
gfs
IDSS
Forward Transconductance
3.6
–––
–––
Drain-to-Source Leakage Current
–––
–––
-25
–––
–––
-250
IGSS
V
Gate-to-Source Forward Leakage
–––
–––
100
Gate-to-Source Reverse Leakage
–––
–––
-100
Ω
µA
nA
VGS = -10V, ID
J
VDS = VGS, ID = -250µA
VDS = -50V, ID = -6.6A
VDS = -150V, VGS = 0V
h
VDS = -120V, VGS = 0V, TJ = 150°C
VGS = 20V
VGS = -20V
Dynamic Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
Qg
Total Gate Charge
Qgs
Gate-to-Source Charge
Qgd
Gate-to-Drain ("Miller") Charge
td(on)
Turn-On Delay Time
tr
td(off)
Min. Typ. Max. Units
–––
Conditions
–––
66
ID = -6.6A
–––
–––
8.1
–––
–––
35
VGS = -10V, See Fig 6 and 13
–––
14
–––
VDD = -75V
Rise Time
–––
36
–––
Turn-Off Delay Time
–––
53
–––
tf
Fall Time
–––
37
–––
LD
Internal Drain Inductance
–––
4.5
–––
LS
Internal Source Inductance
–––
7.5
–––
Ciss
Input Capacitance
–––
860
–––
Coss
Output Capacitance
–––
220
–––
Crss
Reverse Transfer Capacitance
–––
130
–––
nC
ns
VDS =-120V
fh
ID = -6.6A
RG = 6.8Ω
RD = 12Ω, See Fig. 10
fh
Between lead,
nH
D
6mm (0.25in.)
G
from package
S
and center of die contact
VGS = 0V
pF
VDS = -25V
ƒ = 1.0MHz, See Fig.5
h
Diode Characteristics
Parameter
IS
Continuous Source Current
ISM
(Body Diode)
Pulsed Source Current
ch
Min. Typ. Max. Units
–––
–––
MOSFET symbol
-13
A
–––
-44
VSD
(Body Diode)
Diode Forward Voltage
–––
–––
–––
-1.6
V
trr
Reverse Recovery Time
–––
160
240
ns
Qrr
Reverse Recovery Charge
–––
1.2
1.7
ton
Forward Turn-On Time
Notes 
2
Conditions
showing the
integral reverse
D
G
p-n junction diode.
TJ = 25°C, IS =-6.6A, VGS = 0V
TJ = 25°C, IF =-6.6A
di/dt = 100A/µs
f
S
fh
nC
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
through ˆ are on page 10
www.irf.com
AUIRFR6215
Qualification Information†
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive
qualification.
IR’s Industrial and Consumer
qualification level is granted by extension of the
higher Automotive level.
Qualification Level
Moisture Sensitivity Level
Machine Model
D PAK
MSL1
Class M4
AEC-Q101-002
ESD
Human Body Model
Class H3A
AEC-Q101-001
Charged Device Model
Class C5
AEC-Q101-005
RoHS Compliant
Yes
† Qualification standards can be found at International Rectifier’s web site: http//www.irf.com/
†† Exceptions to AEC-Q101 requirements are noted in the qualification report.
www.irf.com
3
AUIRFR6215
100
100
VGS
- 15V
- 10V
- 8.0V
- 7.0V
- 6.0V
- 5.5V
- 5.0V
BOTTOM - 4.5V
VGS
- 15V
- 10V
- 8.0V
- 7.0V
- 6.0V
- 5.5V
- 5.0V
BOTTOM - 4.5V
TOP
-ID , Drain-to-Source Current (A)
-ID , Drain-to-Source Current (A)
TOP
10
20µs PULSE WIDTH
Tc = 25°C
A
-4.5V
1
1
10
10
-4.5V
100
1
-VDS , Drain-to-Source Voltage (V)
2.5
TJ = 175°C
10
VDS = -50V
20µs PULSE WIDTH
6
7
8
9
-VGS , Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
4
R DS(on) , Drain-to-Source On Resistance
(Normalized)
-ID , Drain-to-Source Current (A)
TJ = 25°C
5
A
100
Fig 2. Typical Output Characteristics
100
4
10
-VDS , Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
1
20µs PULSE WIDTH
TC = 175°C
1
10
A
I D = -11A
2.0
1.5
1.0
0.5
VGS = -10V
0.0
-60 -40 -20
0
20
40
60
A
80 100 120 140 160 180
TJ , Junction Temperature (°C)
Fig 4. Normalized On-Resistance
Vs. Temperature
www.irf.com
AUIRFR6215
2000
-VGS , Gate-to-Source Voltage (V)
1600
C, Capacitance (pF)
20
V GS = 0V,
f = 1MHz
C iss = Cgs + C gd , Cds SHORTED
C rss = C gd
C oss = C ds + C gd
Ciss
1200
Coss
800
Crss
400
0
1
10
100
A
I D = -6.6A
16
12
8
4
FOR TEST CIRCUIT
SEE FIGURE 13
0
0
-VDS , Drain-to-Source Voltage (V)
20
40
60
80
A
Q G , Total Gate Charge (nC)
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
100
100
OPERATION IN THIS AREA LIMITED
BY R DS(on)
10µs
-I D , Drain Current (A)
-ISD , Reverse Drain Current (A)
VDS = -120V
VDS = -75V
VDS = -30V
TJ = 175°C
10
TJ = 25°C
1
100µs
10
1ms
VGS = 0V
0.1
0.2
0.6
1.0
1.4
-VSD , Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
www.irf.com
A
1.8
TC = 25°C
TJ = 175°C
Single Pulse
1
1
10ms
10
100
A
1000
-VDS , Drain-to-Source Voltage (V)
Fig 8. Maximum Safe Operating Area
5
AUIRFR6215
14
VGS
12
-ID , Drain Current (A)
RD
VDS
D.U.T.
RG
10
-
+
V DD
-10V
8
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
6
Fig 10a. Switching Time Test Circuit
4
td(on)
2
tr
t d(off)
tf
VGS
0
10%
25
50
75
100
125
TC , Case Temperature
150
175
( °C)
90%
Fig 9. Maximum Drain Current Vs.
Case Temperature
VDS
Fig 10b. Switching Time Waveforms
Thermal Response (ZthJC )
10
1
D = 0.50
0.20
0.10
0.1
PDM
0.05
t
0.02
0.01
SINGLE PULSE
(THERMAL RESPONSE)
0.01
0.00001
Notes:
1. Duty factor D = t
1
/t
1
t2
2
2. Peak TJ = P DM x Z thJC + T C
0.0001
0.001
0.01
0.1
A
1
t 1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
6
www.irf.com
L
VDS
D.U.T
RG
IAS
-20V
tp
VDD
A
DRIVER
0.01Ω
15V
Fig 12a. Unclamped Inductive Test Circuit
I AS
EAS , Single Pulse Avalanche Energy (mJ)
AUIRFR6215
800
TOP
BOTTOM
ID
-2.7A
-4.7A
-6.6A
600
400
200
A
0
25
50
75
100
125
150
175
Starting TJ , Junction Temperature (°C)
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
tp
V(BR)DSS
Fig 12b. Unclamped Inductive Waveforms
Current Regulator
Same Type as D.U.T.
QG
50KΩ
12V
-10V
QGS
.3µF
QGD
D.U.T.
+VDS
VGS
VG
-3mA
Charge
Fig 13a. Basic Gate Charge Waveform
www.irf.com
.2µF
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
7
AUIRFR6215
Peak Diode Recovery dv/dt Test Circuit
+
D.U.T
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
ƒ
+
‚
-
-
„
+

RG
*
•
•
•
•
+
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
-
VDD
Reverse Polarity of D.U.T for P-Channel
Driver Gate Drive
Period
P.W.
D=
P.W.
Period
VGS=10V
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 14. For N-Channel HEXFETS
8
www.irf.com
AUIRFR6215
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak Part Marking Information
Part Number
AURFR6215
YWWA
IR Logo
XX
or
Date Code
Y= Year
WW= Work Week
A= Automotive, Lead Free
XX
Lot Code
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
www.irf.com
9
AUIRFR6215
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
FEED DIRECTION
TRL
16.3 ( .641 )
15.7 ( .619 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
Notes:
 Repetitive rating; pulse width limited by
max. junction temperature. ( See fig. 11 )
‚ Starting TJ = 25°C, L = 14mH R G = 25Ω, IAS = -6.6A. (See Fig.12)
ƒ ISD ≤-6.6A, di/dt ≤ -620A/µs, VDD ≤ V(BR)DSS, TJ ≤ 175°C
„ Pulse width ≤ 300µs; duty cycle ≤ 2%
… This is applied for I-PAK, LS of D-PAK is measured between lead
and center of die contact
† Uses IRF6215 data and test conditions
‡ When mounted on 1" square PCB (FR-4 or G-10 Material ) For
recommended footprint and soldering techniques refer to
application note #AN-994
ˆ Rθ is measured at TJ approximately 90°C.
10
www.irf.com
AUIRFR6215
Ordering Information
Base part
AUIRFR6215
AUIRFR6215
AUIRFR6215
AUIRFR6215
www.irf.com
Package Type
Dpak
Standard Pack
Form
Tube
Tape and Reel
Tape and Reel Left
Tape and Reel Right
Complete Part Number
Quantity
75
2000
3000
3000
AUIRFR6215
AUIRFR6215TR
AUIRFR6215TRL
AUIRFR6215TRR
11
AUIRFR6215
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR)
reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and
services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix
follow automotive industry and / or customer specific requirements with regards to product discontinuance and process
change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order
acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s
standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products
and applications using IR components. To minimize the risks with customer products and applications, customers should
provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and
is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with
alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation.
Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or
service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive
business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into
the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the
IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products
for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of
the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR
products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as
military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has
not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all
legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR
products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the
designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications,
IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
12
www.irf.com