GP08A THRU GP08J GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 0.8 Ampere DO-204AL T E D * FEATURES P A T E N 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 0.8 Ampere operation at TA=55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension MECHANICAL DATA for suffix "E" part numbers Dimensions in inches and (millimeters) Glass-plastic encapsulation technique is covered by Patent No.3,996,602 and brazed-lead assembly by Patent No.3,930,306 * ® Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GP08A GP08B GP08D GP08G GP08J UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 Volts Maximum RMS voltage VRMS 35 70 140 280 420 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TA =55°C I(AV) 0 .8 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TA=55°C IFSM 25.0 Amps VF 1.3 Volts IR(AV) 30.0 µA IR 5.0 50.0 µA Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ 8.0 pF RΘJA 55.0 °C/W TJ, TSTG -65 to +175 °C Maximum instantaneous forward voltage at 0.8A Maximum full load reverse current full cycle average 0.375" (9.5mm) lead length at TA=55°C Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Measure on IF =0.5A, IR =1.0A, Irr = 0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted 4/98 RATINGS AND CHARACTERISTIC CURVES GP08A THRU GP08J FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1.0 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.8 0.6 0.4 0.2 0.375" (9.5mm) LEAD LENGTH 0 20 60 40 100 80 120 140 AMBIENT TEMPERATURE, °C 160 180 25 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 20 15 10 5.0 0 1 100 10 NUMBER OF CYCLES AT 60 Hz FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 20 1 0.1 0 0.4 0.6 0.8 1.0 1.2 10 TJ=100°C 1 0.1 TJ=25°C 0.01 1.4 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25°C f=1.0 MHZ Vsig=50mVp-p JUNCTION CAPACITANCE, pF 100 10 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 0.1 0.01 0.1 1 10 t, PULSE DURATION, sec 100