TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 1.5-A LOW-NOISE FAST-TRANSIENT-RESPONSE LOW-DROPOUT REGULATOR Check for Samples: TL1963A-Q1 FEATURES 1 • • • • • • • • • Qualified for Automotive Applications Optimized for Fast Transient Response Output Current: 1.5 A Dropout Voltage: 340 mV Low Noise: 40 mVRMS (10 Hz to 100 kHz) 1-mA Quiescent Current No Protection Diodes Needed Controlled Quiescent Current in Dropout Fixed Output Voltages: 1.5 V, 1.8 V, 2.5 V, and 3.3 V Adjustable Output Voltage: 1.21 V to 20 V Less Than 1-mA Quiescent Current in Shutdown Stable with 10-mF Output Capacitor Stable with Ceramic Capacitors • • • • • • • Reverse-Battery Protection No Reverse Current Thermal Limiting APPLICATIONS • • 3.3-V to 2.5-V Logic Power Supplies Post Regulator for Switching Supplies KTT PACKAGE (TOP VIEW) 5 4 3 2 1 SENSE/ADJ OUT GND IN SHDN DESCRIPTION/ORDERING INFORMATION The TL1963A is a low-dropout (LDO) regulator optimized for fast transient response. The device can supply 1.5 A of output current with a dropout voltage of 340 mV. Operating quiescent current is 1 mA, dropping to less than 1 mA in shutdown. Quiescent current is well controlled; it does not rise in dropout as it does with many other regulators. In addition to fast transient response, the TL1963A regulators have very low output noise, which makes them ideal for sensitive RF supply applications. Output voltage range is from 1.21 V to 20 V. The TL1963A regulators are stable with output capacitors as low as 10 mF. Small ceramic capacitors can be used without the necessary addition of ESR, as is common with other regulators. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting, and reverse-current protection. The devices are available in fixed output voltages of 1.5 V, 1.8 V, 2.5 V, and 3.3 V, and as an adjustable device with a 1.21-V reference voltage. The TL1963A regulators are available in the 5-pin TO-263 (KTT), 6-pin TO-223 (DCQ), and 3-pin SOT-223 (DCY) packages. ORDERING INFORMATION (1) TJ –40°C to 125°C (1) (2) VOUT (TYP) PACKAGE (2) ORDERABLE PART NUMBER TOP-SIDE MARKING 1.5 V TL1963A-15QKTTRQ1 PREVIEW 1.8 V TL1963A-18QKTTRQ1Q1 PREVIEW 2.5 V TL1963A-25QKTTRQ1 PREVIEW 3.3 V TO-263 – KTT Reel of 500 TL1963A-33QKTTRQ1 PREVIEW ADJ TL1963AQKTTRQ1 TL1963AQ For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010, Texas Instruments Incorporated TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com TERMINAL FUNCTIONS NO. NAME DESCRIPTION KTT 1 Shutdown. The SHDN pin is used to put the TL1963A regulators into a low-power shutdown state. The output is off when the SHDN pin is pulled low. The SHDN pin can be driven either by 5-V logic or open-collector logic with a pullup resistor. The pullup resistor is required to supply the pullup current of the open-collector gate, normally several microamperes, and the SHDN pin current, typically 3 mA. If unused, the SHDN pin must be connected to VIN. The device is in the low-power shutdown state if the SHDN pin is not connected. IN 2 Input. Power is supplied to the device through the IN pin. A bypass capacitor is required on this pin if the device is more than six inches away from the main input filter capacitor. In general, the output impedance of a battery rises with frequency, so it is advisable to include a bypass capacitor in battery-powered circuits. A bypass capacitor (ceramic) in the range of 1 mF to 10 mF is sufficient. The TL1963A regulators are designed to withstand reverse voltages on the IN pin with respect to ground and the OUT pin. In the case of a reverse input, which can happen if a battery is plugged in backwards, the device acts as if there is a diode in series with its input. There is no reverse current flow into the regulator, and no reverse voltage appears at the load. The device protects both itself and the load. GND 3 Ground OUT 4 Output. The output supplies power to the load. A minimum output capacitor (ceramic) of 10 mF is required to prevent oscillations. Larger output capacitors are required for applications with large transient loads to limit peak voltage transients. ADJ 5 Adjust. For the adjustable TL1963A, this is the input to the error amplifier. This pin is clamped internally to ±7 V. It has a bias current of 3 mA that flows into the pin. The ADJ pin voltage is 1.21 V referenced to ground, and the output voltage range is 1.21 V to 20 V. 5 Sense. For fixed voltage versions of the TL1963A (TL1963A-1.5, TL1963A-1.8, TL1963A-2.5, and TL1963A-3.3), the SENSE pin is the input to the error amplifier. Optimum regulation is obtained at the point where the SENSE pin is connected to the OUT pin of the regulator. In critical applications, small voltage drops are caused by the resistance (RP) of PC traces between the regulator and the load. These may be eliminated by connecting the SENSE pin to the output at the load as shown in Figure 32. Note that the voltage drop across the external PC traces adds to the dropout voltage of the regulator. The SENSE pin bias current is 600 mA at the rated output voltage. The SENSE pin can be pulled below ground (as in a dual supply system in which the regulator load is returned to a negative supply) and still allow the device to start and operate. SHDN SENSE Thermal Pad For the KTT package, the exposed thermal pad is connected to ground and must be soldered to the PCB for rated thermal performance. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VIN Input voltage range IN –20 V to 20 V OUT –20 V to 20 V Input-to-output differential (2) –20 V to 20 V SENSE –20 V to 20 V ADJ –7 V to 7 V SHDN –20 V to 20 V tshort Output short-circuit duration TJ Operating virtual-junction temperature range –40°C to 125°C Tstg Storage temperature range –65°C to 150°C (1) (2) Indefinite Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Absolute maximum input-to-output differential voltage cannot be achieved with all combinations of rated IN pin and OUT pin voltages. With the IN pin at 20 V, the OUT pin may not be pulled below 0 V. The total measured voltage from IN to OUT cannot exceed ±20 V. PACKAGE THERMAL DATA (1) (1) (2) 2 PACKAGE BOARD qJA qJC TO-263 (KTT) High K, JESD 51-5 26.5°C/W 24.1°C/W qJP (2) 0.38°C/W Maximum power dissipation is a function of TJ(max), qJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/qJA. Operating at the absolute maximum TJ of 150°C can affect reliability. For packages with exposed thermal pads, such as QFN, PowerPAD™, and PowerFLEX™, qJP is defined as the thermal resistance between the die junction and the bottom of the exposed pad. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 ELECTRICAL CHARACTERISTICS (1) Over operating temperature range TJ = –40°C to 125°C (unless otherwise noted) PARAMETER TEST CONDITIONS Minimum input voltage (3) VIN (4) ILOAD = 1.5 A Full range 2.1 2.5 VIN = 2.5 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 2.3 V, ILOAD = 1 mA Regulated output voltage (5) VIN = 2.8 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 3 V, ILOAD = 1 mA TL1963A-2.5 VIN = 3.5 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 3.8 V, ILOAD = 1 mA TL1963A-3.3 VIN = 4.3 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 2.21 V, ILOAD = 1 mA Line regulation Load regulation (1) (2) (3) (4) (5) (5) MAX 1.9 TL1963A-1.8 ADJ pin voltage (3) TYP (2) 25°C VIN = 2.21 V, ILOAD = 1 mA VADJ MIN ILOAD = 0.5 A TL1963A-1.5 VOUT TJ 25°C 1.477 1.500 1.523 Full range 1.447 1.500 1.545 25°C 1.773 1.800 1.827 Full range 1.737 1.800 1.854 25°C 2.462 2.500 2.538 Full range 2.412 2.500 2.575 25°C 3.250 3.300 3.350 Full range 3.200 3.300 3.400 25°C 1.192 1.21 1.228 VIN = 2.5 V to 20 V, ILOAD = 1 mA to 1.5 A Full range 1.174 1.21 1.246 TL1963A-1.5 ΔVIN = 2.21 V to 20 V, ILOAD = 1 mA Full range 2 6 TL1963A-1.8 ΔVIN = 2.3 V to 20 V, ILOAD = 1 mA Full range 2.5 7 TL1963A-2.5 ΔVIN = 3 V to 20 V, ILOAD = 1 mA Full range 3 10 TL1963A-3.3 ΔVIN = 3.8 V to 20 V, ILOAD = 1 mA Full range 3.5 10 TL1963A (3) ΔVIN = 2.21 V to 20 V, ILOAD = 1 mA Full range 1.5 5 TL1963A-1.5 VIN = 2.5 V, ΔILOAD = 1 mA to 1.5 A 2 9 TL1963A 25°C Full range 25°C TL1963A-1.8 VIN = 2.8 V, ΔILOAD = 1 mA to 1.5 A Full range TL1963A-2.5 VIN = 3.5 V, ΔILOAD = 1 mA to 1.5 A Full range TL1963A-3.3 VIN = 4.3 V, ΔILOAD = 1 mA to 1.5 A TL1963A (3) VIN = 2.5 V, ΔILOAD = 1 mA to 1.5 A 25°C 25°C Full range V V V mV 18 2 10 20 2.5 15 30 3 Full range 25°C UNIT mV 20 70 2 8 18 The TL1963A regulators are tested and specified under pulse load conditions such that TJ ≈ TA. The TL1963A is fully tested at TA = 25°C. Performance at –40°C and 125°C is specified by design, characterization, and correlation with statistical process controls. Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the application and configuration and may vary over time. Typical values are not ensured on production material. The TL1963A (adjustable version) is tested and specified for these conditions with the ADJ pin connected to the OUT pin. For the TL1963A, TL1963A-1.5 and TL1963A-1.8, dropout voltages are limited by the minimum input voltage specification under some output voltage/load conditions. Operating conditions are limited by maximum junction temperature. The regulated output voltage specification does not apply for all possible combinations of input voltage and output current. When operating at maximum input voltage, the output current range must be limited. When operating at maximum output current, the input voltage range must be limited. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 3 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com ELECTRICAL CHARACTERISTICS (1) (continued) Over operating temperature range TJ = –40°C to 125°C (unless otherwise noted) PARAMETER TEST CONDITIONS Dropout voltage (4) (6) VIN = VOUT(NOMINAL) (7) eN IADJ Output voltage noise ADJ pin bias current ILOAD = 100 mA I SHDN 0.06 0.1 0.17 0.22 25°C 0.19 Full range 0.27 0.34 Full range 0.55 Full range 1 1.5 ILOAD = 1 mA Full range 1.1 1.6 ILOAD = 100 mA Full range 3.8 5.5 ILOAD = 500 mA Full range 15 25 ILOAD = 1.5 A Full range 80 120 25°C 40 25°C VOUT = OFF to ON Full range VOUT = ON to OFF Full range 0.25 3 10 0.9 2 0.75 25°C 0.01 1 25°C 3 30 Quiescent current in shutdown VIN = 6 V, V SHDN = 0 V 25°C 0.01 1 Ripple rejection VIN – VOUT = 1.5 V (avg), VRIPPLE = 0.5 VP-P, fRIPPLE = 120 Hz, ILOAD = 0.75 A 25°C IIL Input reverse leakage current Reverse output current (10) VIN = 7 V, VOUT = 0 V 55 25°C VIN = VOUT(NOMINAL) + 1 Full range VIN = –20 V, VOUT = 0 V Full range mA mVRMS V SHDN = 20 V Current limit V 0.45 ILOAD = 0 mA COUT = 10 mF, ILOAD = 1.5 A, BW = 10 Hz to 100 kHz UNIT 0.35 25°C V SHDN = 0 V SHDN pin current ILIMIT IRO 0.02 Full range (3) (9) Shutdown threshold MAX 0.1 25°C ILOAD = 1.5 A IGND TYP (2) Full range ILOAD = 500 mA GND pin current (7) (8) VIN = VOUT(NOMINAL) + 1 MIN 25°C ILOAD = 1 mA VDROPOUT TJ 63 mA V mA mA dB 2 A 1.6 1 TL1963A-1.5 VOUT = 1.5 V, VIN < 1.5 V 25°C 600 1200 TL1963A-1.8 VOUT = 1.8 V, VIN < 1.8 V 25°C 600 1200 TL1963A-2.5 VOUT = 2.5 V, VIN < 2.5 V 25°C 600 1200 TL1963A-3.3 VOUT = 3.3 V, VIN < 3.3 V 25°C 600 1200 TL1963A VOUT = 1.21 V, VIN < 1.21 V 25°C 300 600 mA mA (6) Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage is equal to: VIN – VDROPOUT. (7) To satisfy requirements for minimum input voltage, the TL1963A (adjustable version) is tested and specified for these conditions with an external resistor divider (two 4.12-kΩ resistors) for an output voltage of 2.4 V. The external resistor divider adds a 300-mA DC load on the output. (8) GND pin current is tested with VIN = (VOUT(NOMINAL) + 1 V) and a current source load. The GND pin current decreases at higher input voltages. (9) ADJ pin bias current flows into the ADJ pin. (10) Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. This current flows into the OUT pin and out the GND pin. 4 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 TYPICAL CHARACTERISTICS DROPOUT VOLTAGE vs OUTPUT CURRENT DROPOUT VOLTAGE vs TEMPERATURE 500 480 450 IOUT = 1.5 A 400 Dropout Voltage – mV Dropout Voltage – mV 360 350 TA = 125°C 300 250 200 TA = 25°C 150 240 IOUT = 0.5 A IOUT = 100 mA 120 100 50 IOUT = 1 mA 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 -50 1.6 -25 Output Current – A QUIESCENT CURRENT vs TEMPERATURE OUTPUT VOLTAGE vs TEMPERATURE VIN = 6 V 100 125 100 125 VTL1963A-1.8 OUT Fixed 1.8 V IIOUT OUT = 1 mA 1.83 VSHDN = VIN 1.82 1.1 Output Voltage – V Quiescent Current – mA 75 1.84 1.2 VOUT Fixed 3.3 V TL1963A-3.3 1 0.9 VOUT Adjustable TL1963A (Adjustable) 0.8 1.81 1.8 1.79 1.78 0.7 1.77 0.6 0.5 -50 50 Figure 2. IOUT = 0 A 1.3 25 Figure 1. 1.5 1.4 0 TA – Free-Air Temperature – °C 1.76 -25 0 25 50 75 100 125 -50 -25 TA – Free-Air Temperature – °C Figure 3. 0 25 50 75 TA – Free-Air Temperature – °C Figure 4. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 5 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) OUTPUT VOLTAGE vs TEMPERATURE OUTPUT VOLTAGE vs TEMPERATURE 2.58 2.56 3.38 VOUT Fixed 2.5 V TL1963A-2.5 IIOUT = 1 mA OUT = 1 mA 3.34 Output Voltage – V 2.54 Output Voltage – V VTL1963A-3.3 OUT Fixed 3.3 V IOUT = 1 mA IOUT 3.36 2.52 2.5 2.48 3.32 3.3 3.28 2.46 3.26 2.44 3.24 2.42 -50 3.22 -25 0 25 50 75 100 -50 125 -25 0 Figure 5. Figure 6. OUTPUT VOLTAGE vs TEMPERATURE QUIESCENT CURRENT vs INPUT VOLTAGE 1.23 125 ROUT = 4.3 k W 1 1.21 1.205 1.2 VSHDN = VIN VOUT Adjustable TL1963A (Adjustable) 0.8 0.6 0.4 0.2 1.195 0 -25 0 25 50 75 100 125 0 2 TA – Free-Air Temperature – °C Figure 7. 6 100 TJ = 25°C VOUT Adjustable TL1963A (Adjustable) IIOUT = 1 mA OUT = 1 mA VIN V V IN = 6 V 1.215 1.19 -50 75 1.2 Quiescent Current – mA Output Voltage – V 1.22 50 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C 1.225 25 4 6 8 10 12 14 16 18 20 Input Voltage – V Figure 8. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 TYPICAL CHARACTERISTICS (continued) GROUND CURRENT vs INPUT VOLTAGE GROUND CURRENT vs INPUT VOLTAGE 10 100 TJ = 25°C 90 VSHDN = VIN TL1963A (Adjustable) VOUT Adjustable 80 TL1963A (Adjustable) VOUT Adjustable 8 VOUT = 1.21 V 70 VOUT = 1.21 V 60 Ground Current – mA Ground Current – mA TJ = 25°C VSHDN = VIN IOUT = 1.5 A 50 40 IOUT = 1 A 30 6 IOUT = 300 mA 4 IOUT = 100 mA 20 2 IOUT = 0.5 A 10 IOUT = 10 mA 0 0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 Input Voltage – V Input Voltage – V Figure 9. Figure 10. GROUND CURRENT vs INPUT VOLTAGE GROUND CURRENT vs INPUT VOLTAGE 40 8 9 10 120 TJ = 25°C TJ = 25°C VSHDN = VIN 35 VSHDN = VIN 100 VOUT Fixed 3.3 V TL1963A-3.3 TL1963A-3.3 VOUT Fixed 3.3 V Ground Current – mA Ground Current – mA 30 25 IOUT = 300 mA 20 IOUT = 100 mA 15 IOUT = 10 mA 80 IOUT = 1.5 A 60 40 IOUT = 1 A 10 20 IOUT = 0.5 A 5 0 0 0 1 2 3 4 5 6 7 8 9 10 0 1 Input Voltage – V 2 3 4 5 6 7 8 9 10 Input Voltage – V Figure 11. Figure 12. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 7 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) GROUND CURRENT vs OUTPUT CURRENT SHDN INPUT CURRENT vs TEMPERATURE 1 80 VIN = VOUT(nom) + 1 VSHDN = 0 V 70 SHDN Input Current – µA Ground Current – mA 60 50 40 30 20 0.75 0.5 0.25 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 -50 1.6 -25 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C Output Current – A Figure 13. Figure 14. SHDN INPUT CURRENT vs SHDN INPUT VOLTAGE SHDN THRESHOLD (OFF TO ON) vs TEMPERATURE 2.5 1 2.25 0.9 2 0.8 SHDN Input Voltage – V SHDN Input Current – µA IOUT = 1 mA 1.75 1.5 1.25 1 0.75 0.7 0.6 0.5 0.4 0.3 0.5 0.2 0.25 0.1 0 0 2 4 6 8 10 12 14 16 18 20 0 -50 -25 25 50 75 TA – Free-Air Temperature – °C SHDN Input Voltage – V Figure 15. 8 0 Figure 16. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 TYPICAL CHARACTERISTICS (continued) SHDN THRESHOLD (ON TO OFF) vs TEMPERATURE ADJ BIAS CURRENT vs TEMPERATURE 5 1 0.9 4.5 0.8 4 0.7 3.5 ADJ Bias Current – µA SHDN Input Voltage – V IOUT = 1 mA 0.6 0.5 0.4 0.3 3 2.5 2 1.5 0.2 1 0.1 0.5 0 -50 -25 0 25 50 75 100 0 -50 125 -25 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C Figure 17. Figure 18. CURRENT LIMIT vs INPUT/OUTPUT DIFFERENTIAL VOLTAGE CURRENT LIMIT vs TEMPERATURE 3.5 5 D ?VOUT = 100 mV VIN = 7 V VOUT = 0 V 3 TA = -40°C 4 TA = 25°C Current Limit – A Current Limit – A 2.5 2 TA = 125°C 1.5 3 2 1 1 0.5 0 0 2 4 6 8 10 12 14 16 18 20 0 -50 -25 Input/Output Differential Voltage – V Figure 19. 0 25 50 75 TA – Free-Air Temperature – °C Figure 20. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 9 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) REVERSE OUTPUT CURRENT vs OUTPUT VOLTAGE REVERSE OUTPUT CURRENT vs TEMPERATURE 12 1000 TJ = 25°C VIN = 0 V VIN = 0 V Current flows into OUT pin Reverse Output Current – µA Reverse Output Current – mA 10 8 VOUT(Adjustable) Adjustable TL1963A VOUT =VVOUT ADJ = VADJ 6 4 2 800 600 VOUT Fixed 3.3V TL1963A-3.3 VOUT= =3.3 3.3VV VOUT 400 V OUT Adjustable TL1963A (Adjustable) VOUT = 1.21 1.21VV OUT = 200 0 VOUT Fixed 3.3 V TL1963A-3.3 VOUT= =VVFB VOUT FB -2 0 2 4 6 8 0 -50 10 -25 Output Voltage – V 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C Figure 21. Figure 22. RIPPLE REJECTION vs FREQUENCY LOAD REGULATION vs TEMPERATURE 80 20 IOUT = 1.5 A 15 70 10 Load Regulation – mV Ripple Rejection – dB 60 50 40 30 20 10 VIN = 2.7 V VIN = 2.7 V CIN = 0 CIN = 0 COUT = 10 µF (ceramic) COUT = 10 µF IOUT = 750 mA IOUT = 750 mA VRipple = 0.05 VPP VRipple = 0.05 Vpp TA = 25°C 100 1000 1k 0 -5 -10 -15 TL1963A-1.8 VOUT Fixed 1.8 V TL1963A-2.5 VOUT Fixed 2.5 V -20 -25 TL1963A-3.3 VOUT Fixed 3.3 V -30 -35 0 10 TL1963A VOUT(Adjustable) Adjustable 5 10000 10k 100000 100k 100000 1M -50 -25 25 50 75 TA – Free-Air Temperature – °C Frequency – Hz Figure 23. 10 0 Figure 24. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 TYPICAL CHARACTERISTICS (continued) OUTPUT NOISE VOLTAGE vs FREQUENCY LOAD TRANSIENT RESPONSE 1 V = 4.3 V VIN IN = 4.3 V CIN C µF IN = 10 µF COUT == 10 C 10 µF µF (ceramic) Change in Outupt Voltage OUT TL1963A-3.3 V OUT Fixed 3.3 V 0.1 Load Current Output Noise Hz Output NoiseVoltage Voltage––µV/ µVÖRMS 10(ceramic) µF COUTC=OUT 10=µF IOUT =IOUT 1.5=A1.5 A TL1963A (Adjustable) VOUT Adjustable 0.01 10 100 1k Frequency - Hz 10k 20 mV VOUT 0 mV -20 mV 500 mA IOUT 10 mA 100k 500 µs per division Figure 25. Figure 26. Change in Outupt Voltage LOAD TRANSIENT RESPONSE VININ == 4.3 4.3VV V CININ ==10 10 µF µF C = OUT C =10 10µF µF(ceramic) OUT VOUT 20 mV 0 mV Load Current -20 mV 1.5 A IOUT 10 mA 500 µs per division Figure 27. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 11 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com APPLICATION INFORMATION The TL1963A series are 1.5-A LDO regulators optimized for fast transient response. The devices are capable of supplying 1.5 A at a dropout voltage of 340 mV. The low operating quiescent current (1 mA) drops to less than 1 mA in shutdown. In addition to the low quiescent current, the TL1963A regulators incorporate several protection features which make them ideal for use in battery-powered systems. The devices are protected against both reverse input and reverse output voltages. In battery-backup applications where the output can be held up by a backup battery when the input is pulled to ground, the TL1963A acts as if it has a diode in series with its output and prevents reverse current flow. Additionally, in dual-supply applications where the regulator load is returned to a negative supply, the output can be pulled below ground by as much as 20 V and still allow the device to start and operate. Typical Applications IN 10 µF (ceramic) VIN > 3 V 2.5 V at 1.5 A OUT 10 µF (ceramic) TL1963A-2.5 SENSE SHDN GND Figure 29. 3.3 V to 2.5 V Regulator R5 0.01 W TL1963A-1.8 OUT IN VIN > 2.7 V C1 10 µF R1 1 kW + LOAD SHDN SENSE GND R2 80.6 kW R4 2.2 kW R6 2.2 kW C3 1 µF R3 2 kW + C2 3.3 µF R8 100 kW R7 470 kW - NOTE: All capacitors are ceramic. Figure 30. Adjustable Current Source 12 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 R1 0.01 W IN VIN > 3.7 V 3.3 V at 3 A OUT TL1963A-3.3 C1 10 µF C2 22 µF SHDN SENSE GND R2 0.01 W IN OUT R6 6.65 kW TL1963A SHDN SHDN SENSE GND R7 4.12 kW R3 2.2 kW R4 2.2 kW R5 1 kW + – C3 0.01 µF NOTE: All capacitors are ceramic. Figure 31. Paralleling Regulators for Higher Output Current RP IN OUT TL1963A VIN SHDN SENSE Load GND RP Figure 32. Kelvin Sense Connection Adjustable Operation The adjustable version of the TL1963A has an output voltage range of 1.21 V to 20 V. The output voltage is set by the ratio of two external resistors as shown in Figure 33. The device maintains the voltage at the ADJ pin at 1.21 V referenced to ground. The current in R1 is then equal to 1.21 V / R1, and the current in R2 is the current in R1 plus the ADJ pin bias current. The ADJ pin bias current, 3 mA at 25°C, flows through R2 into the ADJ pin. The output voltage can be calculated using the formula shown in Figure 33. The value of R1 should be less than 4.17 kΩ to minimize errors in the output voltage caused by the ADJ pin bias current. Note that in shutdown the output is turned off, and the divider current is zero. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 13 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com IN VOUT OUT TL1963A R2 VIN ADJ GND R1 R2 + (I ADJ)(R2) VOUT = 1.21 V )1 + R1) VADJ = 1.21 V IADJ = 3 µA at 25°C Output range = 1.21 V to 20 V Figure 33. Adjustable Operation The adjustable device is tested and specified with the ADJ pin tied to the OUT pin for an output voltage of 1.21 V. Specifications for output voltages greater than 1.21 V are proportional to the ratio of the desired output voltage to 1.21 V: VOUT/1.21 V. For example, load regulation for an output current change of 1 mA to 1.5 A is –3 mV (typ) at VOUT = 1.21 V. At VOUT = 5 V, load regulation is: (5 V/1.21 V)(–3 mV) = –12.4 mV Output Capacitance and Transient Response The TL1963A regulators are designed to be stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 10 mF with an ESR of 3 Ω or less is recommended to prevent oscillations. Larger values of output capacitance can decrease the peak deviations and provide improved transient response for larger load current changes. Bypass capacitors, used to decouple individual components powered by the TL1963A, increase the effective output capacitor value. Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior over temperature and applied voltage. The most common dielectrics used are Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but exhibit strong voltage and temperature coefficients. When used with a 5-V regulator, a 10-mF Y5V capacitor can exhibit an effective value as low as 1 mF to 2 mF over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be induced by vibrations in the system or thermal transients. Overload Recovery Like many IC power regulators, the TL1963A has safe operating area protection. The safe area protection decreases the current limit as input-to-output voltage increases and keeps the power transistor inside a safe operating region for all values of input-to-output voltage. The protection is designed to provide some output current at all values of input-to-output voltage up to the device breakdown. When power is first turned on, as the input voltage rises, the output follows the input, allowing the regulator to start up into very heavy loads. During start up, as the input voltage is rising, the input-to-output voltage differential is small, allowing the regulator to supply large output currents. With a high input voltage, a problem can occur wherein removal of an output short does not allow the output voltage to recover. Other regulators also exhibit this phenomenon, so it is not unique to the TL1963A. 14 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 The problem occurs with a heavy output load when the input voltage is high and the output voltage is low. Common situations are immediately after the removal of a short circuit or when the shutdown pin is pulled high after the input voltage has already been turned on. The load line for such a load may intersect the output current curve at two points. If this happens, there are two stable output operating points for the regulator. With this double intersection, the input power supply may need to be cycled down to zero and brought up again to make the output recover. Output Voltage Noise The TL1963A regulators have been designed to provide low output voltage noise over the 10-Hz to 100-kHz bandwidth while operating at full load. Output voltage noise is typically 40 nV/√Hz over this frequency bandwidth for the TL1963A (adjustable version). For higher output voltages (generated by using a resistor divider), the output voltage noise is gained up accordingly. This results in RMS noise over the 10-Hz to 100-kHz bandwidth of 14 mVRMS for the TL1963A, increasing to 38 mVRMS for the TL1963A-3.3. Higher values of output voltage noise may be measured when care is not exercised with regards to circuit layout and testing. Crosstalk from nearby traces can induce unwanted noise onto the output of the TL1963A. Power-supply ripple rejection must also be considered; the TL1963A regulators do not have unlimited power-supply rejection and pass a small portion of the input noise through to the output. Thermal Considerations The power handling capability of the device is limited by the maximum rated junction temperature (125°C). The power dissipated by the device is made up of two components: 1. Output current multiplied by the input/output voltage differential: IOUT(VIN – VOUT) 2. GND pin current multiplied by the input voltage: IGNDVIN. The GND pin current can be found using the GND Pin Current graphs in Typical Characteristics. Power dissipation is equal to the sum of the two components listed above. The TL1963A series regulators have internal thermal limiting designed to protect the device during overload conditions. For continuous normal conditions, the maximum junction temperature rating of 125°C must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. Additional heat sources mounted nearby must also be considered. For surface-mount devices, heat sinking is accomplished by using the heat-spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes also can be used to spread the heat generated by power devices. Table 1 lists thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 1/16-inch FR-4 board with one-ounce copper. Table 1. KTT Package (5-Pin TO-263) COPPER AREA (1) BOARD AREA THERMAL RESISTANCE (JUNCTION TO AMBIENT) 2500 mm2 2500 mm2 23°C/W 1000 mm 2 2500 mm 2500 mm2 25°C/W 125 mm2 2500 mm2 2500 mm2 33°C/W TOPSIDE (1) BACKSIDE 2500 mm2 2 Device is mounted on topside. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 15 TL1963A-Q1 SLVSA79 – APRIL 2010 www.ti.com Calculating Junction Temperature Example: Given an output voltage of 3.3 V, an input voltage range of 4 V to 6 V, an output current range of 0 mA to 500 mA, and a maximum ambient temperature of 50°C, what is the maximum junction temperature? The power dissipated by the device is equal to: IOUT(MAX)(VIN(MAX) – VOUT) + IGND(VIN(MAX)) where, IOUT(MAX) = 500 mA VIN(MAX) = 6 V IGND at (IOUT = 500 mA, VIN = 6 V) = 10 mA So, P = 500 mA (6 V – 3.3 V) + 10 mA (6 V) = 1.41 W Using a KTT package, the thermal resistance is in the range of 23°C/W to 33°C/W, depending on the copper area. So the junction temperature rise above ambient is approximately equal to: 1.41 W × 28°C/W = 39.5°C The maximum junction temperature is then be equal to the maximum junction-temperature rise above ambient plus the maximum ambient temperature or: TJMAX = 50°C + 39.5°C = 89.5°C Protection Features The TL1963A regulators incorporate several protection features that make them ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the devices are protected against reverse input voltages, reverse output voltages and reverse voltages from output to input. Current limit protection and thermal overload protection are intended to protect the device against current overload conditions at the output of the device. For normal operation, the junction temperature should not exceed 125°C. The input of the device withstands reverse voltages of 20 V. Current flow into the device is limited to less than 1 mA (typically less than 100 mA), and no negative voltage appears at the output. The device protects both itself and the load. This provides protection against batteries that can be plugged in backward. The output of the TL1963A can be pulled below ground without damaging the device. If the input is left open circuit or grounded, the output can be pulled below ground by 20 V. For fixed voltage versions, the output acts like a large resistor, typically 5 kΩ or higher, limiting current flow to typically less than 600 mA. For adjustable versions, the output acts like an open circuit; no current flows out of the pin. If the input is powered by a voltage source, the output sources the short-circuit current of the device and protects itself by thermal limiting. In this case, grounding the SHDN pin turns off the device and stops the output from sourcing the short-circuit current. The ADJ pin of the adjustable device can be pulled above or below ground by as much as 7 V without damaging the device. If the input is left open circuit or grounded, the ADJ pin acts like an open circuit when pulled below ground and like a large resistor (typically 5 kΩ) in series with a diode when pulled above ground. In situations where the ADJ pin is connected to a resistor divider that would pull the ADJ pin above its 7-V clamp voltage if the output is pulled high, the ADJ pin input current must be limited to less than 5 mA. For example, a resistor divider is used to provide a regulated 1.5-V output from the 1.21-V reference when the output is forced to 20 V. The top resistor of the resistor divider must be chosen to limit the current into the ADJ pin to less than 5 mA when the ADJ pin is at 7 V. The 13-V difference between OUT and ADJ pins divided by the 5-mA maximum current into the ADJ pin yields a minimum top resistor value of 2.6 kΩ. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage, or is left open circuit. 16 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 TL1963A-Q1 www.ti.com SLVSA79 – APRIL 2010 When the IN pin of the TL1963A is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current typically drops to less than 2 mA. This can happen if the input of the device is connected to a discharged (low voltage) battery and the output is held up by either a backup battery or a second regulator circuit. The state of the SHDN pin has no effect on the reverse output current when the output is pulled above the input. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TL1963A-Q1 17 PACKAGE OPTION ADDENDUM www.ti.com 1-May-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing TL1963AQKTTRQ1 ACTIVE DDPAK/ TO-263 KTT Pins Package Eco Plan (2) Qty 5 500 Green (RoHS & no Sb/Br) Lead/Ball Finish CU SN MSL Peak Temp (3) Level-3-245C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TL1963A-Q1 : • Catalog: TL1963A NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device TL1963AQKTTRQ1 Package Package Pins Type Drawing SPQ DDPAK/ TO-263 500 KTT 5 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 10.6 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 15.8 4.9 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL1963AQKTTRQ1 DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated