TI TLV61220DBVR

TLV61220
www.ti.com
SLVSB53 – MAY 2012
LOW INPUT VOLTAGE STEP-UP CONVERTER IN THIN SOT-23 PACKAGE
Check for Samples: TLV61220
FEATURES
APPLICATIONS
•
•
1
•
•
•
•
•
•
•
•
Up to 95% Efficiency at Typical Operating
Conditions
5.5 μA Quiescent Current
Startup Into Load at 0.7 V Input Voltage
Operating Input Voltage from 0.7 V to 5.5 V
Pass-Through Function during Shutdown
Minimum Switching Current 200 mA
Protections:
– Output Overvoltage
– Overtemperature
– Input Undervoltage Lockout
Adjustable Output Voltage from 1.8 V to 5.5 V
Small 6-pin Thin SOT-23 Package
•
•
•
•
•
Battery Powered Applications
– 1 to 3 Cell Alkaline, NiCd or NiMH
– 1 Cell Li-Ion or Li-Primary
Solar or Fuel Cell Powered Applications
Consumer and Portable Medical Products
Personal Care Products
White or Status LEDs
Smartphones
DESCRIPTION
The TLV61220 provides a power-supply solution for products powered by either a single-cell, two-cell, or threecell alkaline, NiCd or NiMH, or one-cell Li-Ion or Li-polymer battery. Possible output currents depend on the
input-to-output voltage ratio. The boost converter is based on a hysteretic controller topology using synchronous
rectification to obtain maximum efficiency at minimal quiescent currents. The output voltage of the adjustable
version can be programmed by an external resistor divider, or is set internally to a fixed output voltage. The
converter can be switched off by a featured enable pin. While being switched off, battery drain is minimized. The
device is packaged in a 6-pin thin SOT-23 package (DBV).
spacer
L1 4.7:H
TLV61220
SW
VOUT
VOUT
1.8V to 5.5V
R1
VBAT
VIN
0.7V to VOUT
C1
10:F
EN
C2
FB
R2
10:F
GND
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TLV61220
SLVSB53 – MAY 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE DEVICE OPTIONS
TA
OUTPUT VOLTAGE
DC/DC
PACKAGE
PART NUMBER
–40°C to 85°C
Adjustable
6-Pin SOT-23
TLV61220DBV
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
– 0.3 to
7.5
V
Operating junction temperature range
–40
150
°C
Storage temperature range
–65
150
°C
2
kV
1.5
kV
VIN
Input voltage range on VBAT, SW, VOUT, EN, FB
TJ
Tstg
Human Body Model (HBM)
ESD
(1)
(2)
(2)
Charged Device Model (CDM) (2)
UNIT
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
ESD testing is performed according to the respective JESD22 JEDEC standard.
DISSIPATION RATINGS TABLE
PACKAGE
THERMAL
RESISTANCE
ΘJA (1)
THERMAL
RESISTANCE
ΘJB
THERMAL
RESISTANCE
ΘJC
POWER RATING
TA ≤ 25°C
DERATING FACTOR
ABOVE
TA = 25°C
DBV
130 °C/W
27 °C/W
41 °C/W
769 mW
7.7 mW/°C
(1)
Thermal ratings are determined assuming a high K PCB design according to JEDEC standard JESD51-7.
RECOMMENDED OPERATING CONDITIONS
MIN
VIN
Supply voltage at VIN
0.7
TA
Operating free air temperature range
TJ
Operating virtual junction temperature range
2
Submit Documentation Feedback
NOM
MAX
UNIT
5.5
V
–40
85
°C
–40
125
°C
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
ELECTRICAL CHARACTERISTICS
over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature
range of 25°C) (unless otherwise noted)
DC/DC STAGE
PARAMETER
TEST CONDITIONS
VIN
Input voltage range
VIN
Minimum input voltage at startup
RLoad ≥ 150 Ω
VOUT
TLV61220 output voltage range
VIN < VOUT
VFB
TLV61220 feedback voltage
ILH
Inductor current ripple
ISW
switch current limit
TYP
0.7
1.8
483
500
UNIT
5.5
V
0.7
V
5.5
V
513
mV
200
mA
VOUT = 3.3 V, VIN = 1.2 V, TA = 25 °C
220
400
mA
VOUT = 3.3 V, TA = -40°C to 85 °C
180
400
mA
VOUT = 3.3 V, TA = 0°C to 85 °C
200
400
mA
mΩ
VOUT = 5 V
700
mΩ
VOUT = 3.3 V
600
mΩ
VOUT = 5 V
550
mΩ
Line regulation
VIN < VOUT
0.5 %
Load regulation
VIN < VOUT
0.5 %
Main switch on resistance, LSD
IQ
Quiescent
current
ISD
Shutdown
current
VIN
VOUT
VIN
VOUT = 3.3 V
IO = 0 mA, VEN = VIN = 1.2 V, VOUT = 3.3 V
VEN = 0 V, VIN = 1.2 V, VOUT ≥ VIN
0.5
0.9
μA
5
7.5
μA
0.2
0.5
μA
Leakage current into VOUT
VEN = 0 V, VIN = 1.2 V, VOUT = 3.3 V
Leakage current into SW
VEN = 0 V, VIN = 1.2 V, VSW = 1.2 V, VOUT ≥ VIN
0.01
IFB
TLV61220 Feedback input
current
VFB = 0.5 V
0.01
IEN
EN input current
Clamped on GND or VIN (VIN < 1.5 V)
ILKG
MAX
1000
Rectifying switch on resistance,
HSD
RDS(on)
MIN
μA
1
0.005
μA
0.2
μA
μA
0.1
CONTROL STAGE
PARAMETER
TEST CONDITIONS
VIL
EN input low voltage
VIN ≤ 1.5 V
VIH
EN input high voltage
VIN ≤ 1.5 V
VIL
EN input low voltage
5 V > VIN > 1.5 V
VIH
EN input high voltage
5 V > VIN > 1.5 V
VUVLO
Undervoltage lockout threshold for
turn off
VIN decreasing
Overvoltage protection threshold
MIN
TYP
MAX
UNIT
0.2 × VIN
0.8 × VIN
V
V
0.4
1.2
V
V
0.5
5.5
0.7
7.5
V
V
Overtemperature protection
140
°C
Overtemperature hysteresis
20
°C
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
3
TLV61220
SLVSB53 – MAY 2012
www.ti.com
PIN ASSIGNMENTS
DBV PACKAGE
TOP VIEW
VBAT VOUT
6
FB
5
4
ABC
1
2
3
SW
GND
EN
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
EN
3
I
Enable input (VBAT enabled, GND disabled)
FB
4
I
Voltage feedback for programming the output voltage
GND
2
SW
1
VBAT
VOUT
IC ground connection for logic and power
I
Boost and rectifying switch input
6
I
Supply voltage
5
O
Boost converter output
FUNCTIONAL BLOCK DIAGRAM (ADJUSTABLE VERSION)
SW
VOUT
VOUT
VIN
Gate
Driver
VBAT
Start Up
EN
Device
Control
GND
4
Current
Sensor
FB
VREF
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
PARAMETER MEASUREMENT INFORMATION
L1 4.7:H
TLV61220
SW
VOUT
VOUT
1.8V to 5.5V
R1
VBAT
VIN
0.7V to VOUT
EN
C1
10:F
C2
FB
R2
10:F
GND
Table 1. List of Components:
COMPONENT
REFERENCE
PART NUMBER
MANUFACTURER
VALUE
C1
GRM188R60J106ME84D
Murata
10 μF, 6.3V. X5R Ceramic
C2
GRM188R60J106ME84D
Murata
10 μF, 6.3V. X5R Ceramic
L1
1269AS-H-4ZR7N
Toko
4.7 μH
R1, R2
R1= 1MΩ, R2= Values depending on the programmed
output voltage
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
5
TLV61220
SLVSB53 – MAY 2012
www.ti.com
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Output Current
Efficiency
Efficiency
Output Voltage
Waveforms
Input Voltage, ISW = 330 mA, Minimum ISW= 200 mA, VO = 1.8V
1
Input Voltage, ISW = 400 mA, Minimum ISW = 200 mA, VO = 3.3V
2
Input Voltage, ISW = 380 mA, Minimum ISW = 200 mA, VO = 5V
3
vs Output Current, VO = 1.8 V, VI = [0.7 V; 1.2 V; 1.5 V]
4
vs Output Current, VO = 3.3 V, VI = [0.7 V; 1.2 V; 2.4V; 3V]
5
vs Output Current, VO = 5 V, VI = [0.7 V; 1.2 V; 3.6V; 4.2V]
6
vs Input Voltage, VO = 1.8 V, IO = [100µA; 1mA ; 10mA; 50mA]
7
vs Input Voltage, VO = 3.3 V, IO = [100µA; 1mA ; 10mA; 50mA]
8
vs Input Voltage, VO = 5 V, IO = [100µA; 1mA ; 10mA; 50mA]
9
vs Output Current, , VO = 1.8 V, VI = [0.7 V; 1.2 V]
10
vs Output Current, , VO = 3.3 V, VI = [0.7 V; 1.2 V; 2.4 V]
11
Load transient, VI = 1.2 V, VO = 3.3 V, IO = 5mA to 20 mA
12
Line transient, VI = 1.8 V to 2.4V, VO = 3.3 V, IO = 30 mA
13
Startup after Enable, VI = 1.2 V, VO = 3.3 V, RLOAD = 50 Ω
14
MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE
(VO=3.3V, Minimum ISW=200mA, L=4.7µH)
0.16
0.27
0.14
0.24
Output Current - A
Output Current - A
MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE
(VO=1.8V, Minimum ISW=200mA, L=4.7µH)
0.12
0.1
ISW=330mA
0.08
0.06
0.21
0.18
0.15
ISW=400mA
0.12
0.09
0.04
0.06
Minimum ISW
0.02
0
0.9
1.0
1.1
1.2
1.3
1.4
0
0.7
1.2
1.7
2.2
2.7
3
Input Voltage - V
Input Voltage - V
Figure 1.
6
Minimum ISW
0.03
Figure 2.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
EFFICIENCY
vs
OUTPUT CURRENT AND INPUT VOLTAGE (VO=1.8V)
MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE
(VO=5V, Minimum ISW=200mA, L=4.7µH)
0.27
100
0.24
90
Vo=1.8V
80
70
0.18
Efficiency- %
Output Current - A
0.21
0.15
0.12
ISW=380mA
0.09
60
VI=1.2V
VI=0.7V
50
40
30
0.06
20
0.03
10
Minimum ISW
0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0
0.01
4.5
0.1
Input Voltage - V
1
10
Output Current - mA
100
G000
Figure 3.
Figure 4.
EFFICIENCY
vs
OUTPUT CURRENT AND INPUT VOLTAGE (VO=1.8V)
EFFICIENCY
vs
INPUT VOLTAGE AND OUTPUT CURRENT (VO=5V)
100
100
Vo=5V
Vo=3.3V
90
90
80
80
70
70
VI=2.4V
60
50
Efficiency - %
Efficiency- %
VI=1.5V
VI=3V
VI=0.7V
VI=1.2V
40
60
VI=3.6V
=0.7V
30
20
20
10
10
0.1
1
10
Output Current - mA
100
VI=1.2V
=0.7V
VI=0.7V
40
30
0
0.01
VI=4.2V
=0.7V
50
0
0.01
G000
Figure 5.
0.1
1
10
Output Current - mA
100
G000
Figure 6.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
7
TLV61220
SLVSB53 – MAY 2012
www.ti.com
EFFICIENCY
vs
INPUT VOLTAGE AND OUTPUT CURRENT (VO=1.8V)
EFFICIENCY
vs
INPUT VOLTAGE AND OUTPUT CURRENT (VO=3.3V)
100
100
Vo=1.8V
90
Io=10mA
Vo=3.3V
90
Io=10mA
80
80
Io=1mA
70
Io=1mA
Efficiency - %
Efficiency - %
70
Io=50mA
60
50
Io=100:A
40
Io=50mA
60
50
30
30
20
20
10
10
0
0.7
0.9
1.1
1.3
1.5
1.7
Io=100:A
40
0
0.7
1.9
1.2
1.7
2.2
2.7
3.2
3.7
Input Voltage - V
Input Voltage - V
Figure 7.
Figure 8.
EFFICIENCY
vs
INPUT VOLTAGE AND OUTPUT CURRENT (VO=5V)
OUTPUT VOLTAGE
vs
OUTPUT CURRENT AND INPUT VOLTAGE (VO=1.8V)
100
1.9
Vo=5V
Io=1mA
VoI=0.7V
=1.8V
90
80
Io=1mA
1.9
Output Voltage - V
Efficiency - %
70
Io=100:A
60
Io=50mA
50
40
30
VI=1.2V
=0.7V
1.8
VI=0.7V
1.8
20
10
0
0.7
8
1.7
2.7
3.7
4.7
5.7
1.7
0.01
0.1
1
10
Input Voltage - V
Output Current - mA
Figure 9.
Figure 10.
Submit Documentation Feedback
100
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
OUTPUT VOLTAGE
vs
OUTPUT CURRENT AND INPUT VOLTAGE (VO=3.3V)
LOAD TRANSIENT RESPONSE
3.5
Vo=3.3V
Output Voltage
20mV/div, AC
Output Voltage - V
3.4
VI=1.2V
VI=2.4V
3.3
Output Current
10mA/div, DC
3.2
VI=0.7V
VIN = 1.2V, VOUT=3.3V, IOUT= 5mA to 20mA
3.1
0.01
0.1
1
10
100
Output Current - mA
Figure 11.
Figure 12.
LINE TRANSIENT RESPONSE
START UP AFTER ENABLE
Enable Voltage
2V/div, DC
Output Voltage
1V/div, DC
Input Voltage
500mV/div, DC
Load Current
20mA/div, DC
Output Voltage
100mV/div, AC
Inductor Current
200mA/div, DC
VIN = 1.2V, VOUT=3.3V, RLOAD= 50S
VIN = 1.8V to 2.4V, VOUT=3.3V, IOUT= 30mA
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
9
TLV61220
SLVSB53 – MAY 2012
www.ti.com
DETAILED DESCRIPTION
OPERATION
The TLV61220 is a high performance, high efficient boost converter. To achieve high efficiency the power stage
is realized as a synchronous boost topology. For the power switching two actively controlled low RDS(on) power
MOSFETs are implemented.
CONTROLLER CIRCUIT
The device is controlled by a hysteretic current mode controller. This controller regulates the output voltage by
keeping the inductor ripple current constant in the range of 200 mA and adjusting the offset of this inductor
current depending on the output load. In case the required average input current is lower than the average
inductor current defined by this constant ripple the inductor current gets discontinuous to keep the efficiency high
at low load conditions.
IL
Continuous Current Operation
Discontinuous Current Operation
200 mA
(typ.)
200 mA
(typ.)
t
Figure 15. Hysteretic Current Operation
The output voltage VOUT is monitored via the feedback network which is connected to the voltage error amplifier.
To regulate the output voltage, the voltage error amplifier compares this feedback voltage to the internal voltage
reference and adjusts the required offset of the inductor current accordingly. At fixed output voltage versions an
internal feedback network is used to program the output voltage, at adjustable versions an external resistor
divider needs to be connected.
The self oscillating hysteretic current mode architecture is inherently stable and allows fast response to load
variations. It also allows using inductors and capacitors over a wide value range.
Device Enable and Shutdown Mode
The device is enabled when EN is set high and shut down when EN is low. During shutdown, the converter stops
switching and all internal control circuitry is turned off. In this case the input voltage is connected to the output
through the back-gate diode of the rectifying MOSFET. This means that there always will be voltage at the output
which can be as high as the input voltage or lower depending on the load.
Startup
After the EN pin is tied high, the device starts to operate. In case the input voltage is not high enough to supply
the control circuit properly a startup oscillator starts to operate the switches. During this phase the switching
frequency is controlled by the oscillator and the maximum switch current is limited. As soon as the device has
built up the output voltage to about 1.8 V, high enough for supplying the control circuit, the device switches to its
normal hysteretic current mode operation. The startup time depends on input voltage and load current.
Operation at Output Overload
If in normal boost operation the inductor current reaches the internal switch current limit threshold the main
switch is turned off to stop further increase of the input current.
In this case the output voltage will decrease since the device can not provide sufficient power to maintain the set
output voltage.
If the output voltage drops below the input voltage the backgate diode of the rectifying switch gets forward biased
and current starts flow through it. This diode cannot be turned off, so the current finally is only limited by the
remaining DC resistances. As soon as the overload condition is removed, the converter resumes providing the
set output voltage.
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
Undervoltage Lockout
An implemented undervoltage lockout function stops the operation of the converter if the input voltage drops
below the typical undervoltage lockout threshold. This function is implemented in order to prevent malfunctioning
of the converter.
Overvoltage Protection
If, for any reason, the output voltage is not fed back properly to the input of the voltage amplifier, control of the
output voltage will not work anymore. Therefore an overvoltage protection is implemented to avoid the output
voltage exceeding critical values for the device and possibly for the system it is supplying. For this protection the
TLV61220 output voltage is also monitored internally. In case it reaches the internally programmed threshold of
6.5 V typically the voltage amplifier regulates the output voltage to this value.
If the TLV61220 is used to drive LEDs, this feature protects the circuit if the LED fails.
Overtemperature Protection
The device has a built-in temperature sensor which monitors the internal IC junction temperature. If the
temperature exceeds the programmed threshold (see electrical characteristics table), the device stops operating.
As soon as the IC temperature has decreased below the programmed threshold, it starts operating again. To
prevent unstable operation close to the region of overtemperature threshold, a built-in hysteresis is implemented.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
11
TLV61220
SLVSB53 – MAY 2012
www.ti.com
APPLICATION INFORMATION
DESIGN PROCEDURE
The TLV61220 is intended for systems powered by a single cell battery to up to three Alkaline, NiCd or NiMH
cells with a typical terminal voltage between 0.7 V and 5.5 V. They can also be used in systems powered by onecell Li-Ion or Li-Polymer batteries with a typical voltage between 2.5 V and 4.2 V. Additionally, any other voltage
source with a typical output voltage between 0.7 V and 5.5 V can be used with the TLV61220.
Adjustable output voltage version
An external resistor divider is used to adjust the output voltage. The resistor divider needs to be connected
between VOUT, FB and GND as shown in Figure 16. When the output voltage is regulated properly, the typical
voltage value at the FB pin is 500 mV for the adjustable devices. The maximum recommended value for the
output voltage is 5.5 V. The current through the resistive divider should be about 100 times greater than the
current into the FB pin. The typical current into the FB pin is 0.01 μA, and the voltage across the resistor
between FB and GND, R2, is typically 500 mV. Based on those two values, the recommended value for R2
should be lower than 500 kΩ, in order to set the divider current to 1 μA or higher. The value of the resistor
connected between VOUT and FB, R1, depending on the needed output voltage (VOUT), can be calculated using
Equation 1:
æV
ö
R1 = R 2 x ç OUT - 1÷
V
è FB
ø
(1)
As an example, if an output voltage of 3.3 V is needed, a 1-MΩ resistor is calculated for R1 when for R2 a 180-kΩ
has been selected.
L1 4.7:H
TLV61220
SW
VOUT
VOUT
3.3V/20mA
R1
VBAT
VIN
1V to 3V
C1
10:F
EN
FB
1MS
C2
R2
10:F
180kS
GND
Figure 16. Typical Application Circuit for Adjustable Output Voltage Option
Inductor Selection
To make sure that the TLV61220 can operate, a suitable inductor must be connected between pin VBAT and pin
SW. Inductor values of 4.7 μH show good performance over the whole input and output voltage range .
Choosing other inductance values affects the switching frequency f proportional to 1/L as shown in Equation 2.
L=
V ´ (VOUT - VIN )
1
´ IN
f ´ 200 mA
VOUT
(2)
Choosing inductor values higher than 4.7 μH can improve efficiency due to reduced switching frequency and;
therefore, with reduced switching losses. Using inductor values below 2.2 μH is not recommended.
Having selected an inductance value, the peak current for the inductor in steady state operation can be
calculated. Equation 3 gives the peak current estimate.
IL,MAX
12
ì VOUT ´ IOUT
+ 100 mA; continous current operation
ï
= í 0.8 ´ VIN
ï200 mA;
discontinuous current operation
î
Submit Documentation Feedback
(3)
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
TLV61220
www.ti.com
SLVSB53 – MAY 2012
For selecting the inductor this would be the suitable value for the current rating. It also needs to be taken into
account that load transients and error conditions may cause higher inductor currents.
Equation 4 helps to estimate whether the device will work in continuous or discontinuous operation depending on
the operating points. As long as the inequation is true, continuous operation is typically established. If the
inequation becomes false, discontinous operation is typically established.
VOUT ´ IOUT
> 0.8 ´ 100 mA
VIN
(4)
The following inductor series from different suppliers have been used with TLV61220 converters:
Table 2. List of Inductors
VENDOR
INDUCTOR SERIES
Toko
DFE252010C
Coilcraft
EPL3015
EPL2010
Murata
LQH3NP
Taiyo Yuden
NR3015
Wurth Elektronik
WE-TPC Typ S
Capacitor Selection
Input Capacitor
At least a 10-μF input capacitor is recommended to improve transient behavior of the regulator and EMI behavior
of the total power supply circuit. A ceramic capacitor placed as close as possible to the VBAT and GND pins of
the IC is recommended.
Output Capacitor
For the output capacitor C2 , it is recommended to use small ceramic capacitors placed as close as possible to
the VOUT and GND pins of the IC. If, for any reason, the application requires the use of large capacitors which
can not be placed close to the IC, the use of a small ceramic capacitor with an capacitance value of around
2.2μF in parallel to the large one is recommended. This small capacitor should be placed as close as possible to
the VOUT and GND pins of the IC.
A minimum capacitance value of 4.7 μF should be used, 10 μF are recommended. If the inductor value exceeds
4.7 μH, the value of the output capacitance value needs to be half the inductance value or higher for stability
reasons, see Equation 5.
C2 ³
L
´
2
(5)
The TLV61220 is not sensitive to the ESR in terms of stability. Using low ESR capacitors, such as ceramic
capacitors, is recommended anyway to minimize output voltage ripple. If heavy load changes are expected, the
output capacitor value should be increased to avoid output voltage drops during fast load transients.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
13
TLV61220
SLVSB53 – MAY 2012
www.ti.com
Layout Considerations
As for all switching power supplies, the layout is an important step in the design, especially at high peak currents
and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as
well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground
paths. The input and output capacitor, as well as the inductor should be placed as close as possible to the IC.
The feedback divider should be placed as close as possible to the control ground pin of the IC. To lay out the
ground, it is recommended to use short traces as well, separated from the power ground traces. This avoids
ground shift problems, which can occur due to superimposition of power ground current and control ground
current. Assure that the ground traces are connected close to the device GND pin.
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the powerdissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below.
• Improving the power-dissipation capability of the PCB design
• Improving the thermal coupling of the component to the PCB
• Introducing airflow in the system
For more details on how to use the thermal parameters in the dissipation ratings table please check the Thermal
Characteristics Application Note (SZZA017) and the IC Package Thermal Metrics Application Note (SPRA953).
14
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): TLV61220
PACKAGE OPTION ADDENDUM
www.ti.com
14-Jun-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
TLV61220DBVR
ACTIVE
SOT-23
DBV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLV61220DBVT
ACTIVE
SOT-23
DBV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TLV61220DBVR
SOT-23
DBV
6
3000
178.0
9.0
TLV61220DBVT
SOT-23
DBV
6
250
178.0
9.0
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3.23
3.17
1.37
4.0
8.0
Q3
3.23
3.17
1.37
4.0
8.0
Q3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLV61220DBVR
SOT-23
DBV
6
3000
180.0
180.0
18.0
TLV61220DBVT
SOT-23
DBV
6
250
180.0
180.0
18.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated