SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 D Low Cost D 7-Bit Resolution D Montonicity Over Entire A/D Conversion D D D D D D P PACKAGE (TOP VIEW) ENABLE CLK GND OUTPUT Range Ratiometric Conversion Conversion Speed . . . Approximately 1 ms Single-Supply Operation . . . Either Unregulated 8-V to 18-V (VCC2 Input) or Regulated 3.5-V to 6-V (VCC1 Input) I2L Technology Power Consumption at 5 V . . . 25 mW Typ Regulated 5.5-V Output (≤1 mA) 1 8 2 7 3 6 4 5 RESET VCC2 VCC1 ANALOG INPUT FUNCTION TABLE ANALOG INPUT CONDITION X VI < 200 mV Vramp > VI > 200 mV VI > Vramp description ENABLE L† H H H OUTPUT H L H L † Low level on enable also inhibits the reset function. H = high level, L = low level, X = irrelevant The TL507 is a low-cost single-slope analog-todigital converter designed to convert analog inputvoltages between 0.25 VCC1 and 0.75 VCC1 into a pulse-width-modulated output code. The device contains a 7-bit synchronous counter, a binary weighted resistor ladder network, an operational amplifier, two comparators, a buffer amplifier, an internal regulator, and necessary logic circuitry. Integrated-injection logic (I2L) technology makes it possible to offer this complex circuit at low cost in a small dual-in-line 8-pin package. A high level on RESET clears the counter to zero, which sets the internal ramp to 0.75 VCC. Internal pulldown resistors keep RESET and ENABLE low when not connected. In continuous operation, conversion speeds of up to 1000 conversions per second are possible. The TL507 requires external signals for CLK, RESET, and ENABLE. Versatility and simplicity of operation, coupled with low cost, makes this converter especially useful for a wide variety of applications. The TL507C is characterized for operation from 0°C to 70°C, and the TL507I is characterized for operation from −40°C to 85°C. Copyright 1988, Texas Instruments Incorporated ! "# $!% $ "! "! &! ! !' ! $$ ()% $ "!* $! !!) $! !* "!!% • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 1 SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 functional block diagram (positive logic) Comparator 2 200 mV 5 ANALOG INPUT 4 Output CTR R MSB R 2R CLK 2 + Comparator 1 4R 8R RESET ENABLE 8 1 16R R Regulator 32R 7 64R LSB − + 6 0.25 VCC1 3 VCC2 VCC1 GND indicates an n-p-n open-collector output. schematics of inputs and outputs EQUIVALENT OF ENABLE AND RESET INPUTS EQUIVALENT OF CLOCK INPUT EQUIVALENT OF ANALOG INPUT VCC1 75 kΩ Nom 75 kΩ Nom 100 kΩ Nom Input Input Input Constant Current ≈ 10 µA Output VCC1 10 kΩ Nom 32 kΩ Nom Output 3 kΩ Nom 2 24 kΩ Nom • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC1 (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V Supply voltage, VCC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Input voltage at analog input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V Input voltage at ENABLE, CLK, and RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V On-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Continuous total dissipation at (or below) 25°C free-air temperature (see Note 2) . . . . . . . . . . . . . 1000 mW Operating free-air temperature range: TL507C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70°C TL507I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C NOTES: 1. Voltage values are with respect to network ground terminal unless otherwise noted. 2. For operation above 25°C free-air temperature, derate linearly to 520 mW at 85°C at the rate of 8.0 mW/°C. recommended operating conditions MIN NOM MAX Supply voltage, VCC1 3.5 5 6 V Supply voltage, VCC2 8 15 18 V Input voltage at ANALOG INPUT 0 5.5 V ±18 V Input voltage at ENABLE, CLK, and RESET High-level input voltage, VIH, RESET and ENABLE 2 UNIT V Low-level input voltage, VIL, RESET and ENABLE 0.8 V On-state output voltage 5.5 V Off-state output voltage 1.8 V 150 kHz UNIT Clock frequency, fclock 0 125 electrical characteristics over recommended operating free-air temperature range, VCC1 = VCC2 = 5 V (unless otherwise noted) regular section PARAMETER VCC1 ICC1 Supply voltage (output) ICC2 Supply current TEST CONDITIONS VCC2 = 10 V to 18 V, ICC1 = 0 to − 1 mA VCC1 = 5 V, VCC2 open VCC2 = 15 V, VCC1 open Supply current MIN TYP† MAX 5 5.5 6 V 5 8 mA 7 10 mA TYP† MAX inputs VT+ VTVhys IIH PARAMETER Positive-going threshold voltage‡ Negative-going threshold voltage‡ TEST CONDITIONS MIN 4.5 0.4 CLK Hysteresis (VT+ − VT−) 2 High-level input current RESET, ENABLE, and CLK IIL Low-level input current II Analog input current † All typical values are at TA = 25°C. ‡ These parameters are linear functions of VCC1. VI = 2.4 V VI = 18 V VI = 0 VI = 4 V • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 130 UNIT V V 2.6 4 17 35 V 220 320 ±10 µA 10 300 nA µA 3 SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 output section PARAMETER TEST CONDITIONS IOH IOL High-level output current Low-level output current VOH = 18 V VOL = 5.5 V VOL Low-level output voltage IOL = 1.6 mA MIN 5 TYP† MAX 0.1 100 µA 10 15 mA 80 400 mV MAX UNIT UNIT operating characteristics over recommended operating free-air temperature range, VCC1 = VCC2 = 5.12 V PARAMETER TEST CONDITIONS MIN TYP† Overall error ± 80 mV Differential nonlinearity Zero error‡ See Figure 1 ± 20 mV Binary count = 0 ± 80 mV Scale error Binary count =127 ± 80 mV Full scale input voltage‡ Binary count = 127 Propagation delay time from RESET or ENABLE 3.74 3.82 3.9 2 V µs † All typical values are at TA = 25°C. ‡ These parameters are linear functions of VCC1. definitions zero error The absolute value of the difference between the actual analog voltage at the 01H-to-00H transition and the ideal analog voltage at that transition. overall error The magnitude of the deviation from a straight line between the endpoints of the transfer function. differential nonlinearity The maximum deviation of an analog-value change associated with a 1-bit code change (1 clock pulse) from its theoretical value of 1 LSB. 4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 PARAMETER MEASUREMENT INFORMATION SN74191 CLK OUTPUTS DOWN/UP 4 Test Point Analog Devices AD562 (or equivalent) SN74191 RIPPLE CLOCK 5 kΩ Bits 9 −12 CLK TL507 4 Bits 5 −8 DAC OUT Bits 1− 4 OUTPUTS DOWN/UP TL081 − ANALOG INPUT + Single Clock Pulse 5V SN74191 OUTPUT CLK ENABLE RESET RIPPLE CLOCK 100-kHz CLK INPUT CLK OUTPUTS DOWN/UP 4 Figure 1. Monotonicity and Nonlinearity Test Circuit • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 5 SLAS041 − OCTOBER 1979 − REVISED OCTOBER 1988 PRINCIPLES OF OPERATION The TL507 is a single-slope analog-to-digital converter. All single-slope converters are basically voltage-to-time or current-to-time converters. A study of the functional block diagram shows the versatility of the TL507. An external clock signal is applied through a buffer to a negative-edge-triggered synchronous counter. Binary-weighted resistors from the counter are connected to an operational amplifier used as an adder. The operational amplifier generates a signal that ramps from 0.75 • VCC1 down to 0.25 • VCC1. Comparator 1 compares the ramp signal to the analog input signal. Comparator 2 functions as a fault defector. With the analog input voltage in the range 0.25 • VCC1 to 0.75 • VCC1, the duty cycle of the output signal is determined by the unknown analog input, as shown in Figure 2 and the Function Table. For illustration, assume VCC1 = 5.12 V, 0.25 • VCC1 = 1.28 V 1 binary count + (0.75 * 0.25) V 128 CC1 + 20 mV 0.75 • VCC1 − 1 count = 3.82 V The output is an open-collector n-p-n transistor capable of withstanding up to 18 V in the off state. The output is current limited to the 8- to 12-mA range; however, care must be taken to ensure that the output does not exceed 5.5 V in the on state. The voltage regulator section allows operation f rom either an unregulated 8- to 18-V VCC2 source or a regulated 3.5- to 6-V VCC1 source. Regardless of which external power source is used, the internal circuitry operates at VCC1. When operating from a VCC1 source, VCC2 may be connected to VCC1 or left open. When operating from a VCC2 source, VCC1 can be used as a reference voltage output. 3.82 V Analog Input Level 1 Ramp Input to Comparator 1 Analog Input Level 2 1.28 V Output for Input Level 1 Output for Input Level 2 Figure 2 6 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated