TI CSD97374Q4M

CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
Synchronous Buck NexFET™ Power Stage
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
23
Over 92% System Efficiency at 15A
Max Rated Continuous Current 25A, Peak 60A
High Frequency Operation (up to 2 MHz)
High Density - SON 3.5x4.5-mm Footprint
Ultra Low Inductance Package
System Optimized PCB Footprint
Ultra Low Quiescent (ULQ) Current Mode
3.3V and 5V PWM Signal Compatible
Diode Emulation Mode with FCCM
Input Voltages up to 24V
Three-State PWM Input
Integrated Bootsrap Diode
Shoot Through Protection
RoHS Compliant – Lead Free Terminal Plating
Halogen Free
Ultrabook/Notebook DC/DC Converters
Multiphase Vcore and DDR Solutions
Point-of-Load Synchronous Buck in
Networking, Telecom, and Computing Systems
ORDERING INFORMATION
Device
Package
Media
CSD97374Q4M
SON 3.5 × 4.5-mm
Plastic Package
13-Inch
Reel
Qty
Ship
2500
Tape and
Reel
DESCRIPTION
100
12
90
10
80
8
VGS = 5V
VIN = 12V
VOUT = 1.8V
LOUT = .29µH
fSW = 500kHz
TA = 25ºC
70
60
6
4
2
50
40
Figure 1. Application Diagram
Power Loss (W)
Efficiency (%)
The CSD97374Q4M NexFET™ Power Stage is a highly optimized design for use in a high power, high density
Synchronous Buck converter. This product integrates the driver IC and NexFET technology to complete the
power stage switching function. The driver IC has a built-in selectable diode emulation function that enables
DCM operation to improve light load efficiency. In addition, the driver IC supports ULQ mode that enables
Connected Standby for Windows™ 8 . With the PWM input in tri-state, quiescent current is reduced to 130 µA,
with immediate response. When SKIP# is held at tri-state, the current is reduced to 8 µA (typically 20 µs is
required to resume switching). This combination produces a high current, high efficiency, and high speed
switching device in a small 3.5 × 4.5-mm outline package. In addition, the PCB footprint has been optimized to
help reduce design time and simplify the completion of the overall system design.
0
5
10
15
Output Current (A)
20
25
0
G001
Figure 2. Efficiency and Power Loss
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NexFET is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1)
TA = 25°C (unless otherwise noted)
VALUE
UNIT
MIN
MAX
VIN to PGND
-0.3
30
V
VSW to PGND , VIN to VSW
-0.3
30
V
VSW to PGND, VIN to VSW (<10ns)
-7
33
V
VDD to PGND
–0.3
6
V
PWM, SKIP# to PGND
–0.3
6
V
BOOT to PGND
–0.3
35
V
-2
38
V
–0.3
6
V
Human Body Model (HBM)
2000
V
Charged Device Model (CDM)
500
V
8
W
BOOT to PGND (<10ns)
BOOT to BOOT_R
ESD Rating
Power Dissipation, PD
Operating Temperature Range, TJ
-40
150
°C
Storage Temperature Range, TSTG
–55
150
°C
(1)
Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only
and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating
Conditions" is not implied. Exposure to Absolute Maximum rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
TA = 25° (unless otherwise noted)
Parameter
Conditions
Gate Drive Voltage, VDD
MIN
MAX
4.5
5.5
V
24
V
25
A
60
A
Input Supply Voltage, VIN
Continuous Output Current, IOUT
Peak Output Current, IOUT-PK (2)
Switching Frequency, fSW
VIN = 12V, VDD = 5V, VOUT = 1.8V,
fSW = 500kHz, LOUT = 0.29µH (1)
CBST = 0.1µF (min)
2000
On Time Duty Cycle
85
Minimum PWM On Time
40
Operating Temperature
–40
(1)
(2)
UNIT
kHz
%
ns
125
°C
Measurement made with six 10-µF (TDK C3216X5R1C106KT or equivalent) ceramic capacitors placed across VIN to PGND pins.
System conditions as defined in Note 1. Peak Output Current is applied for tp = 10ms, duty cycle ≤ 1%
THERMAL INFORMATION
TA = 25°C (unless otherwise noted)
PARAMETER
RθJC
Thermal Resistance, Junction-to-Case (Top of package) (1)
RθJB
Thermal Resistance, Junction-to-Board (2)
(1)
(2)
2
MIN
TYP
MAX
UNIT
22.8
°C/W
2.5
°C/W
RθJC is determined with the device mounted on a 1-inch² (6.45 -cm²), 2-oz (.071-mm thick) Cu pad on a 1.5-inch x 1.5-inch, 0.06-inch
(1.52-mm) thick FR4 board.
RθJB value based on hottest board temperature within 1mm of the package.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
ELECTRICAL CHARACTERISTICS
TA = 25°C, VDD = POR to 5.5V (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
PLOSS
Power Loss (1)
VIN = 12V, VDD = 5V, VOUT = 1.8V, IOUT = 15A,
fSW = 500kHz, LOUT = 0.29µH , TJ = 25°C
2.3
W
Power Loss (2)
VIN = 19V, VDD = 5V, VOUT = 1.8V, IOUT = 15A,
fSW = 500kHz, LOUT = 0.29µH , TJ = 25°C
2.5
W
Power Loss (2)
VIN = 19V, VDD = 5V, VOUT = 1.8V, IOUT = 15A,
fSW = 500kHz, LOUT = 0.29µH , TJ = 125°C
2.8
W
VIN
VIN Quiescent Current, IQ
PWM=Floating, VDD = 5V, VIN= 24V
1
µA
VDD
Standby Supply Current, IDD
Operating Supply Current, IDD
PWM = Float, SKIP# = VDD or 0V
130
SKIP# = Float
PWM = 50% Duty cycle, fSW = 500kHz
µA
8
µA
8.2
mA
POWER-ON RESET AND UNDER VOLTAGE LOCKOUT
Power-On Reset, VDD Rising
4.15
UVLO, VDD Falling
3.7
Hysteresis
V
V
0.2
mV
PWM and SKIP# I/O Specifications
Input Impedance, RI
Pull Up to VDD
1700
Pull Down (to GND)
Logic Level High, VIH
kΩ
800
2.65
Logic Level Low, VIL
0.6
Hysteresis, VIH
0.2
Tri-State Voltage, VTS
1.3
V
2
Tri-state Activation Time (falling) PWM,
tTHOLD(off1)
60
Tri-state Activation Time (rising) PWM,
tTHOLD(off2)
60
ns
Tri-state Activation Time (falling) SKIP#,
tTSKF
1
Tri-state Activation Time (rising) SKIP#,
tTSKR
1
µs
Tri-state Exit Time PWM, t3RD(PWM) (2)
Tri-state Exit Time SKIP#, t3RD(SKIP#) (2)
100
ns
50
µs
240
mV
2
µA
BOOTSTRAP SWITCH
Forward Voltage, VFBST
IF = 10mA
Reverse Leakage, IRLEAK (2)
VBST – VDD = 25V
(1)
(2)
120
Measurement made with six 10-µF (TDK C3216X5R1C106KT or equivalent) ceramic capacitors placed across VIN to PGND pins.
Specified by design
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
TYPICAL CHARACTERISTICS
TJ = 125°C, unless stated otherwise.
9
1.2
VIN = 12V
VDD = 5V
VOUT = 1.8V
fSW = 500kHz
LOUT = 0.29µH
6
5
4
3
2
0
1
3
5
7
9
11 13 15 17
Output Current (A)
19
21
23
0.9
0.8
0.7
0.6
Typ
Max
1
1
0.5
−75
25
−50
30
30
25
25
20
15
400LFM
200LFM
100LFM
Nat Conv
5
0
0
10
20
VIN = 12V
VGS = 5V
VOUT = 1.8V
fSW = 500kHz
LOUT = 0.29µH
80
VIN = 12V
VDD = 5V
VOUT = 1.8V
LOUT = 0.29µH
IOUT = 25A
VIN = 12V
VDD = 5V
VOUT = 1.8V
fSW = 500kHz
LOUT = 0.29µH
10
0
0
20
5.3
1.25
4.4
1.2
3.5
1.15
2.7
1.1
1.8
1.05
0.9
1
0.0
0.95
0
400
800
1200
1600
Switching Frequency (kHz)
2000
−0.9
2400
Figure 7. Normalized Power Loss vs Frequency
4
Submit Documentation Feedback
4.4
VDD = 5V
VOUT = 1.8V
LOUT = 0.29µH
fSW = 500kHz
IOUT = 25A
1.2
1.15
3.5
2.7
1.1
1.8
1.05
0.9
1
0.0
0.95
G001
140
G001
1.25
7.1
6.2
120
Figure 6. Typical Safe Operating Area (1)
Power Loss, Normalized
1.3
40
60
80
100
Board Temperature (ºC)
G001
SOA Temperature Adj (ºC)
Power Loss, Normalized
1.35
G001
15
90
8.0
1.45
150
20
5
30
40
50
60
70
Ambient Temperature (ºC)
125
Typ
Max
Figure 5. Safe Operating Area – PCB Horizontal Mount (1)
1.4
0
25
50
75
100
Junction Temperature (ºC)
Figure 4. Power Loss vs Temperature
Output Current (A)
Output Current (A)
Figure 3. Power Loss vs Output Current
10
−25
G001
3
5
7
9
11
13
15
Input Voltage (V)
17
19
21
23
SOA Temperature Adj (ºC)
Power Loss (W)
7
VIN = 12V
VGS = 5V
VOUT = 1.8V
fSW = 500kHz
LOUT = 0.29µH
1.1
Power Loss, Normalized
8
−0.9
G001
Figure 8. Normalized Power Loss vs Input Voltage
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
TYPICAL CHARACTERISTICS (continued)
TJ = 125°C, unless stated otherwise.
VIN = 12V
VDD = 5V
fSW = 500kHz
LOUT = 0.29µH
IOUT = 25A
1.2
5.4
3.6
1.8
1.1
0
1
0.9
−1.8
0.8
−3.6
0.7
−5.4
0.6
0
0.5
1
1.5
2
2.5
Output Voltage (V)
3
3.5
4
1.15
2.7
1.8
1.05
0.9
0
1
−0.9
0.95
−7.2
0.9
0
G001
−1.8
100 200 300 400 500 600 700 800 900 1000 1100
Output Inductance (nH)
G001
Figure 10. Normalized Power Loss vs Output Inductance
45
11
VIN = 12V
VDD = 5V
VOUT = 1.8V
LOUT = 0.29µH
IOUT = 25A
35
30
10.5
Driver Current (mA)
40
25
20
15
10
10
9.5
VIN = 12V
VDD = 5V
VOUT = 1.8V
LOUT = 0.29µH
IOUT = 25A
9
5
0
3.5
1.1
Figure 9. Normalized Power Loss vs Output Voltage
Driver Current (mA)
VIN = 12V
VDD = 5V
VOUT = 1.8V
fSW = 500kHz
IOUT = 25A
1.2
Power Loss, Normalized
1.3
4.4
1.25
7.2
SOA Temperature Adj (ºC)
Power Loss, Normalized
1.4
SOA Temperature Adj (ºC)
9
1.5
0
400
800
1200
1600
Switching Frequency (kHz)
2000
Figure 11. Driver Current vs Frequency
2400
G000
8.5
−75
−50
−25
0
25
50
75
100
Junction Temperature (°C)
125
150
G000
Figure 12. Driver Current vs Temperature
1. The Typical CSD97374Q4M System Characteristic curves are based on measurements made on a PCB design with
dimensions of 4.0" (W) x 3.5" (L) x 0.062" (T) and 6 copper layers of 1 oz. copper thickness. See the Application
Information section for detailed explanation.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
PIN CONFIGURATION
SKIP#
1
8
PWM
VDD
2
7
BOOT
PGND
3
6
BOOT_R
9
PGND
VSW
4
5
VIN
Figure 13. Top View
PIN DESCRIPTION
PIN
NO.
6
DESCRIPTION
NAME
1
SKIP#
This pin enables the Diode Emulation function. When this pin is held Low, Diode Emulation Mode is enabled for the
Sync FET. When SKIP# is High, the CSD97374Q4M operates in Forced Continuous Conduction Mode. A tri-state
voltage on SKIP# puts the driver into a very low power state.
2
VDD
Supply Voltage to Gate Drivers and internal circuitry.
3
PGND
Power Ground, Needs to be connected to Pin 9 and PCB
4
VSW
Voltage Switching Node – pin connection to the output inductor.
5
VIN
Input Voltage Pin. Connect input capacitors close to this pin.
6
BOOT_R
7
BOOT
Bootstrap capacitor connection. Connect a minimum 0.1µF 16V X5R, ceramic cap from BOOT to BOOT_R pins. The
bootstrap capacitor provides the charge to turn on the Control FET. The bootstrap diode is integrated.
8
PWM
Pulse Width modulated 3-state input from external controller. Logic Low sets Control FET gate low and Sync FET gate
high. Logic High sets Control FET gate high and Sync FET gate Low. Open or High Z sets both MOSFET gates low if
greater than the 3-State Shutdown Hold-off Time (t3HT)
9
PGND
Power Ground
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
Figure 14. Functional Block Diagram
FUNCTIONAL DESCRIPTION
POWERING CSD97374Q4M AND GATE DRIVERS
An external VDD voltage is required to supply the integrated gate driver IC and provide the necessary gate drive
power for the MOSFETS. A 1µF 10V X5R or higher ceramic capacitor is recommended to bypass VDD pin to
PGND. A bootstrap circuit to provide gate drive power for the Control FET is also included. The bootstrap supply
to drive the Control FET is generated by connecting a 100nF 16V X5R ceramic capacitor between BOOT and
BOOT_R pins. An optional RBOOT resistor can be used to slow down the turn on speed of the Control FET and
reduce voltage spikes on the VSW node. A typical 1Ω to 4.7Ω value is a compromise between switching loss and
VSW spike amplitude.
Undervoltage Lockout Protection (UVLO)
The undervoltage lockout (UVLO) comparator evaluates the VDD voltage level. As VVDD rises, both the Control
FET and Sync FET gates hold actively low at all times until VVDD reaches the higher UVLO threshold (VUVLO_H).,
Then the driver becomes operational and responds to PWM and SKIP# commands. If VDD falls below the lower
UVLO threshold (VUVLO_L = VUVLO_H – Hysteresis), the device disables the driver and drives the outputs of the
Control FET and Sync FET gates actively low. Figure 15 shows this function.
CAUTION
Do not start the driver in the very low power mode (SKIP# = Tri-state).
VUVLO_H
VUVLO_L
VVDD
Driver On
UDG-12218
Figure 15. UVLO Operation
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
PWM Pin
The PWM pin incorporates an input tri-state function. The device forces the gate driver outputs to low when
PWM is driven into the tri-state window and the driver enters a low power state with zero exit latency. The pin
incorporates a weak pull-up to maintain the voltage within the tri-state window during low-power modes.
Operation into and out of tri-state mode follows the timing diagram outlined in Figure 16.
When VDD reaches the UVLO_H level, a tri-state voltage range (window) is set for the PWM input voltage. The
window is defined the PWM voltage range between PWM logic high (VIH) and logic low (VIL) thresholds. The
device sets high-level input voltage and low-level input voltage threshold levels to accommodate both 3.3 V
(typical) and 5 V (typical) PWM drive signals.
When the PWM exits tri-state, the driver enters CCM for a period of 4 µs, regardless of the state of the SKIP#
pin. Normal operation requires this time period in order for the auto-zero comparator to resume.
Figure 16. PWM Tri-State Timing Diagram
SKIP# Pin
The SKIP# pin incorporates the input tri-state buffer as PWM. The function is somewhat different. When SKIP# is
low, the zero crossing (ZX) detection comparator is enabled, and DCM mode operation occurs if the load current
is less than the critical current. When SKIP# is high, the ZX comparator disables, and the converter enters FCCM
mode. When both SKIP# and PWM are tri-stated, normal operation forces the gate driver outputs low and the
driver enters a low-power state. In the low-power state, the UVLO comparator remains off to reduce quiescent
current. When SKIP# is pulled low, the driver wakes up and is able to accept PWM pulses in less than 50 µs.
Table 1 shows the logic functions of UVLO, PWM, SKIP#, the Control FET Gate and the Sync FET Gate.
Table 1. Logic Functions of the Driver IC
UVLO
(1)
8
PWM
SKIP#
Sync FET Gate
Control FET Gate
MODE
Active
—
—
Low
Low
Disabled
Inactive
Low
Low
High (1)
Low
DCM (1)
Inactive
Low
High
High
Low
FCCM
Inactive
High
H or L
Low
High
Inactive
Tri-state
H or L
Low
Low
LQ
Inactive
—
Tri-state
Low
Low
ULQ
Until zero crossing protection occurs.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
Zero Crossing (ZX) Operation
The zero crossing comparator is adaptive for improved accuracy. As the output current decreases from a heavy
load condition, the inductor current also reduces and eventually arrives at a valley, where it touches zero current,
which is the boundary between continuous conduction and discontinuous conduction modes. The SW pin detects
the zero-current condition. When this zero inductor current condition occurs, the ZX comparator turns off the
rectifying MOSFET.
Integrated Boost-Switch
To maintain a BST-SW voltage close to VDD (to get lower conduction losses on the high-side FET), the
conventional diode between the VDD pin and the BST pin is replaced by a FET which is gated by the DRVL
signal.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
APPLICATION INFORMATION
The Power Stage CSD97374Q4M is a highly optimized design for synchronous buck applications using NexFET
devices with a 5V gate drive. The Control FET and Sync FET silicon are parametrically tuned to yield the lowest
power loss and highest system efficiency. As a result, a rating method is used that is tailored towards a more
systems centric environment. The high-performance gate driver IC integrated in the package helps minimize the
parasitics and results in extremely fast switching of the power MOSFETs. System level performance curves such
as Power Loss, Safe Operating Area and normalized graphs allow engineers to predict the product performance
in the actual application.
Power Loss Curves
MOSFET centric parameters such as RDS(ON) and Qgd are primarily needed by engineers to estimate the loss
generated by the devices. In an effort to simplify the design process for engineers, Texas Instruments has
provided measured power loss performance curves. Figure 3 plots the power loss of the CSD97374Q4M as a
function of load current. This curve is measured by configuring and running the CSD97374Q4M as it would be in
the final application (see Figure 17). The measured power loss is the CSD97374Q4M device power loss which
consists of both input conversion loss and gate drive loss. Equation 1 is used to generate the power loss curve.
Power Loss = (VIN x IIN) + (VDD x IDD) – (VSW_AVG x IOUT)
(1)
The power loss curve in Figure 3 is measured at the maximum recommended junction temperature of
TJ = 125°C under isothermal test conditions.
Safe Operating Curves (SOA)
The SOA curves in the CSD97374Q4M datasheet give engineers guidance on the temperature boundaries within
an operating system by incorporating the thermal resistance and system power loss. Figure 5 and Figure 6
outline the temperature and airflow conditions required for a given load current. The area under the curve
dictates the safe operating area. All the curves are based on measurements made on a PCB design with
dimensions of 4.0" (W) x 3.5" (L) x 0.062" (T) and 6 copper layers of 1 oz. copper thickness.
Normalized Curves
The normalized curves in the CSD97374Q4M data sheet give engineers guidance on the Power Loss and SOA
adjustments based on their application specific needs. These curves show how the power loss and SOA
boundaries will adjust for a given set of systems conditions. The primary Y-axis is the normalized change in
power loss and the secondary Y-axis is the change is system temperature required in order to comply with the
SOA curve. The change in power loss is a multiplier for the Power Loss curve and the change in temperature is
subtracted from the SOA curve.
Figure 17. Power Loss Test Circuit
10
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
Calculating Power Loss and SOA
The user can estimate product loss and SOA boundaries by arithmetic means (see the Design Example).
Though the Power Loss and SOA curves in this datasheet are taken for a specific set of test conditions, the
following procedure will outline the steps engineers should take to predict product performance for any set of
system conditions.
Design Example
Operating Conditions: Output Current (lOUT) = 15A, Input Voltage (VIN ) = 7V, Output Voltage (VOUT) = 1.5V,
Switching Frequency (fSW) = 800kHz, Output Inductor (LOUT) = 0.2µH
Calculating Power Loss
•
•
•
•
•
•
Typical Power Loss at 15A = 2.8W (Figure 3)
Normalized Power Loss for switching frequency ≈ 1.02 (Figure 7)
Normalized Power Loss for input voltage ≈ 1.07 (Figure 8)
Normalized Power Loss for output voltage ≈ 0.94(Figure 9)
Normalized Power Loss for output inductor ≈ 1.08 (Figure 10)
Final calculated Power Loss = 2.8W × 1.02 × 1.07 × 0.94 × 1.08 ≈ 3.1W
Calculating SOA Adjustments
•
•
•
•
•
SOA adjustment for switching frequency ≈ 0.3°C (Figure 7)
SOA adjustment for input voltage ≈ 1.2°C (Figure 8)
SOA adjustment for output voltage ≈ –1.1°C (Figure 9)
SOA adjustment for output inductor ≈ 1.4°C (Figure 10)
Final calculated SOA adjustment = 0.3 + 1.2 + (–1.1) + 1.4 ≈ 1.8°C
Figure 18. Power Stage CSD97374Q4M SOA
In the design example above, the estimated power loss of the CSD97374Q4M would increase to 3.1W. In
addition, the maximum allowable board and/or ambient temperature would have to decrease by 1.8°C. Figure 18
graphically shows how the SOA curve would be adjusted accordingly.
1. Start by drawing a horizontal line from the application current to the SOA curve.
2. Draw a vertical line from the SOA curve intercept down to the board/ambient temperature.
3. Adjust the SOA board/ambient temperature by subtracting the temperature adjustment value.
In the design example, the SOA temperature adjustment yields a reduction in allowable board/ambient
temperature of 1.8°C. In the event the adjustment value is a negative number, subtracting the negative number
would yield an increase in allowable board/ambient temperature.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
RECOMMENDED PCB DESIGN OVERVIEW
There are two key system-level parameters that can be addressed with a proper PCB design: electrical and
thermal performance. Properly optimizing the PCB layout will yield maximum performance in both areas. Below
is a brief description on how to address each parameter.
Electrical Performance
The CSD97374Q4M has the ability to switch at voltage rates greater than 10kV/µs. Special care must be then
taken with the PCB layout design and placement of the input capacitors, inductor and output capacitors.
• The placement of the input capacitors relative to VIN and PGND pins of CSD97374Q4M device should have the
highest priority during the component placement routine. It is critical to minimize these node lengths. As such,
ceramic input capacitors need to be placed as close as possible to the VIN and PGND pins (see Figure 19).
The example in Figure 19 uses 1 x 1nF 0402 25V and 3 x 10µF 1206 25V ceramic capacitors (TDK Part #
C3216X5R1C106KT or equivalent). Notice there are ceramic capacitors on both sides of the board with an
appropriate amount of vias interconnecting both layers. In terms of priority of placement next to the Power
Stage C5, C8 and C6, C19 should follow in order.
• The bootstrap cap CBOOT 0.1µF 0603 16V ceramic capacitor should be closely connected between BOOT and
BOOT_R pins
• The switching node of the output inductor should be placed relatively close to the Power Stage
CSD97374Q4M VSW pins. Minimizing the VSW node length between these two components will reduce the
PCB conduction losses and actually reduce the switching noise level. (2)
Thermal Performance
The CSD97374Q4M has the ability to use the GND planes as the primary thermal path. As such, the use of
thermal vias is an effective way to pull away heat from the device and into the system board. Concerns of solder
voids and manufacturability problems can be addressed by the use of three basic tactics to minimize the amount
of solder attach that will wick down the via barrel:
• Intentionally space out the vias from each other to avoid a cluster of holes in a given area.
• Use the smallest drill size allowed in your design. The example in Figure 19 uses vias with a 10 mil drill hole
and a 16 mil capture pad.
• Tent the opposite side of the via with solder-mask.
In the end, the number and drill size of the thermal vias should align with the end user’s PCB design rules and
manufacturing capabilities.
Figure 19. Recommended PCB Layout (Top Down View)
(2)
12
Keong W. Kam, David Pommerenke, “EMI Analysis Methods for Synchronous Buck Converter EMI Root Cause Analysis”, University of
Missouri – Rolla
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
MECHANICAL DATA
Ө°
c1
a1
D2
4
1
0.300
(x45°)
8
DIM
5
MILLIMETERS
INCHES
Min
Nom
Max
Min
Nom
Max
A
0.800
0.900
1.000
0.031
0.035
0.039
a1
0.000
0.000
0.080
0.000
0.000
0.003
b
0.150
0.200
0.250
0.006
0.008
0.010
b1
2.000
2.200
2.400
0.079
0.087
0.095
b2
0.150
0.200
0.250
0.006
0.008
0.010
c1
0.150
0.200
0.250
0.006
0.008
0.010
D2
3.850
3.950
4.050
0.152
0.156
0.160
E
4.400
4.500
4.600
0.173
0.177
0.181
E1
3.400
3.500
3.600
0.134
0.138
0.142
E2
2.000
2.100
2.200
0.079
0.083
0.087
e
0.400 TYP
0.016 TYP
K
0.300 TYP
0.012 TYP
L
0.300
0.400
0.500
0.012
0.016
0.020
L1
0.180
0.230
0.280
0.007
0.009
0.011
θ
0.00
—
—
0.00
—
—
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
CSD97374Q4M
SLPS382C – JANUARY 2013 – REVISED JULY 2013
www.ti.com
Recommended PCB Land Pattern
(0.010)
0.250
(x18)
(0.006)
0.150
(0.006)
0.150
(0.016)
0.400
(0.024)
0.600 (x 2)
(0.008)
0.200
(x2)
(0.087)
2.200
R0.100
R0.100
0.225 ( x 2)
(0.009)
0.440 (0.017)
(0.088)
2.250
(0.012)
0.300
(0.159)
4.050
RECOMMENDED PCB PATTERN
Recommended Stencil Opening
(0.024)
0.600 (x 2)
(0.008)
0.200
(0.008)
0.200
(0.029)
0.738 (x 8)
(0.016)
0.400
(0.015)
0.390
(0.014)
0.350
0.300
(0.012)
R0.100
0.850 (x8)
(0.033)
(0.012)
0.300
(0.087)
2.200
R0.100
0.225 ( x 2)
(0.009)
(0.004)
0.115
0.440 (0.017)
(0.009)
0.225
(0.008)
0.200
(0.087)
2.200
0.200
(0.008)
NOTE: Dimensions are in mm (inches).
14
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
CSD97374Q4M
www.ti.com
SLPS382C – JANUARY 2013 – REVISED JULY 2013
REVISION HISTORY
Changes from Original (January 2013) to Revision A
Page
•
Changed the ROC table, From: VSW to PGND, VIN to VSW (<20ns) MIN = -5 To: VSW to PGND, VIN to VSW (<10ns) MIN
= -7 ........................................................................................................................................................................................ 2
•
Changed the ROC table, From: BOOT to PGND (<20ns) MIN = -3 To: BOOT to PGND (<10ns) MIN = -2 ............................ 2
•
Changed Logic Level High, VIH From: MAX = 2.6 To: MIN = 2.65 ....................................................................................... 3
•
Changed Logic Level Low, VIL From: MIN = 0.6 To: MAX = 0.6 .......................................................................................... 3
•
Changed Tri-State Voltage, VTS From: MIN = 1.2 To: MIN = 1.3 ......................................................................................... 3
Changes from Revision A (March 2013) to Revision B
Page
•
Changed the Mechanical Drawing image ........................................................................................................................... 13
•
Changed the Recommended PCB Land Pattern image ..................................................................................................... 14
•
Changed the Recommended Stencil Opening image ........................................................................................................ 14
Changes from Revision B (May 2013) to Revision C
•
Page
Added dimension row b2 to the MECHANICAL DATA table .............................................................................................. 13
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
PACKAGE MATERIALS INFORMATION
www.ti.com
31-May-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CSD97374Q4M
Package Package Pins
Type Drawing
VSON
DPC
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
3.8
B0
(mm)
K0
(mm)
P1
(mm)
4.8
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
31-May-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CSD97374Q4M
VSON
DPC
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated