TI CSD87331Q3D

CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
Synchronous Buck NexFET™ Power Block
FEATURES
DESCRIPTION
•
•
•
•
•
•
The CSD87331Q3D NexFET™ power block is an
optimized design for synchronous buck applications
offering high current, high efficiency, and high
frequency capability in a small 3.3-mm × 3.3-mm
outline. Optimized for 5V gate drive applications, this
product offers a flexible solution capable of offering a
high density power supply when paired with any 5V
gate drive from an external controller/driver.
1
2
•
•
•
•
•
•
Half-Bridge Power Block
Up to 27V VIN
Up to 15A Operation
91% system Efficiency at 10A
High Frequency Operation (Up To 1.5MHz)
High Density – SON 3.3-mm × 3.3-mm
Footprint
Optimized for 5V Gate Drive
Low Switching Losses
Ultra Low Inductance Package
RoHS Compliant
Halogen Free
Pb-Free Terminal Plating
TEXT ADDED FOR SPACING
Top View
8
VSW
7
VSW
3
6
VSW
4
5
VIN
1
VIN
2
TG
TGR
PGND
(Pin 9)
APPLICATIONS
•
•
•
•
BG
P0116-01
Synchronous Buck Converters
– High Frequency Applications
– High Current, Low Duty Cycle Applications
Multiphase Synchronous Buck Converters
POL DC-DC Converters
IMVP, VRM, and VRD Applications
TEXT ADDED FOR SPACING
ORDERING INFORMATION
Device
Package
Media
Qty
Ship
CSD87331Q3D
SON
3.3-mm × 3.3-mm
Plastic Package
13-Inch
Reel
2500
Tape and
Reel
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
Efficiency (%)
96
6
88
5
VGS = 5V
VIN = 12V
VOUT = 1.3V
LOUT = 1.0µH
fSW = 500kHz
TA = 25ºC
80
72
64
4
3
2
56
48
Power Loss (W)
TYPICAL POWER BLOCK EFFICIENCY
and POWER LOSS
TYPICAL CIRCUIT
1
0
5
10
Output Current (A)
15
0
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NexFET is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS
TA = 25°C (unless otherwise noted) (1)
PARAMETER
Voltage Range
VALUE
CONDITIONS
MIN
UNIT
MAX
VIN to PGND
30
V
VSW to PGND
30
V
VSW to PGND (10ns)
32
V
TG to TGR
-8
10
V
BG to PGND
-8
10
V
Pulsed Current Rating, IDM
45
A
Power Dissipation, PD
6
W
Avalanche Energy EAS
Sync FET, ID = 42A, L = 0.1mH
88
Control FET, ID = 24A, L = 0.1mH
29
–55
Operating Junction and Storage Temperature Range, TJ, TSTG
(1)
mJ
°C
150
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
TA = 25° (unless otherwise noted)
PARAMETER
CONDITIONS
Gate Drive Voltage, VGS
MIN
MAX
4.5
8
Input Supply Voltage, VIN
Switching Frequency, fSW
UNIT
V
27
CBST = 0.1µF (min)
V
1500
Operating Current
Operating Temperature, TJ
kHz
15
A
125
°C
MAX
UNIT
POWER BLOCK PERFORMANCE (1)
TA = 25° (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
Power Loss, PLOSS (1)
VIN = 12V, VGS = 5V, VOUT = 1.3V,
IOUT = 10A, fSW = 500kHz,
LOUT = 1µH, TJ = 25ºC
1.3
W
VIN Quiescent Current, IQVIN
TG to TGR = 0V BG to PGND = 0V
10
µA
(1)
Measurement made with six 10-µF (TDK C3216X5R1C106KT or equivalent) ceramic capacitors placed across VIN to PGND pins and
using a high current 5V driver IC.
THERMAL INFORMATION
TA = 25°C (unless otherwise stated)
THERMAL METRIC
RθJA
RθJC
(1)
(2)
2
Junction to ambient thermal resistance (Min Cu)
MIN
(1)
TYP
MAX
UNIT
149
Junction to ambient thermal resistance (Max Cu) (1) (2)
80
Junction to case thermal resistance (Top of package) (1)
36
Junction to case thermal resistance (PGND Pin) (1)
°C/W
3.1
2
2
RθJC is determined with the device mounted on a 1-inch (6.45-cm ), 2 oz. (0.071-mm thick) Cu pad on a 1.5-inch × 1.5-inch
(3.81-cm × 3.81-cm), 0.06-inch (1.52-mm) thick FR4 board. RθJC is specified by design while RθJA is determined by the user’s board
design.
Device mounted on FR4 material with 1-inch2 (6.45-cm2) Cu.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
TA = 25°C (unless otherwise stated)
PARAMETER
Q1 Control FET
TEST CONDITIONS
MIN
TYP
Q2 Sync FET
MAX
MIN
TYP
MAX
UNIT
Static Characteristics
BVDSS
Drain to Source Voltage
VGS = 0V, IDS = 250µA
IDSS
Drain to Source Leakage
Current
30
30
VGS = 0V, VDS = 20V
IGSS
Gate to Source Leakage
Current
VDS = 0V, VGS = +10 / –8V
VGS(th)
Gate to Source Threshold
Voltage
VDS = VGS, IDS = 250µA
ZDS(on)
Effective AC On-Impedance
VIN = 12V, VGS = 5V,
VOUT = 1.3V, IOUT = 10A,
fSW = 500kHz,
LOUT = 1µH
18
5.5
mΩ
gfs
Transconductance
VDS = 15V, IDS = 8A
26
48
S
1
V
1
1
µA
100
100
nA
1.2
V
2.1
0.8
Dynamic Characteristics
CISS
Input Capacitance
COSS
Output Capacitance
432
518
926
1110
pF
158
190
378
454
CRSS
Reverse Transfer
Capacitance
pF
7
9
24
30
pF
RG
Qg
Series Gate Resistance
5.2
6.5
0.7
1.5
Ω
Gate Charge Total (4.5V)
2.7
3.2
6.4
7.7
nC
Qgd
Gate Charge - Gate to Drain
Qgs
Gate Charge - Gate to
Source
Qg(th)
Gate Charge at Vth
QOSS
Output Charge
td(on)
Turn On Delay Time
tr
Rise Time
td(off)
Turn Off Delay Time
tf
Fall Time
VGS = 0V, VDS = 15V,
f = 1MHz
VDS = 15V,
IDS = 8A
VDS = 14V, VGS = 0V
VDS = 15V, VGS = 4.5V,
IDS = 8A, RG = 2Ω
0.4
1.1
nC
0.9
1.5
nC
0.5
0.8
nC
3.6
7.7
nC
3.4
3.8
ns
4.5
4.7
ns
7.4
11.2
ns
1.3
2.4
ns
Diode Characteristics
VSD
Diode Forward Voltage
IDS = 8A, VGS = 0V
0.85
Qrr
Reverse Recovery Charge
5.9
nC
Reverse Recovery Time
VDS = 14V, IF = 8A,
di/dt = 300A/µs
4
trr
10
13
ns
LD
HD
LS
LG
HG
M0205-01
Copyright © 2011–2012, Texas Instruments Incorporated
1
V
Max RθJA = 149°C/W
when mounted on
minimum pad area of
2-oz. (0.071-mm thick)
Cu.
MIN Rev0
MIN Rev0
HS
86330Q3D 3.3x3.3
86330Q3D 3.3x3.3
LG
0.85
LD
HD
Max RθJA = 80°C/W
when mounted on
1 inch2 (6.45 cm2) of
2-oz. (0.071-mm thick)
Cu.
HG
1
HS
LS
M0206-01
Submit Documentation Feedback
3
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
TYPICAL POWER BLOCK DEVICE CHARACTERISTICS
Test Conditions: VIN = 12V, VDD = 5V, fSW = 500kHz, VOUT = 1.3V, LOUT = 1µH, IOUT = 15A, TJ = 125°C, unless stated
otherwise.
1.4
3.5
1.3
Power Loss, Normalized
4
Power Loss (W)
3
2.5
2
1.5
1
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
0
0.5
1
3
5
7
9
Output Current (A)
11
13
0.4
−50
15
20
20
15
15
10
5
0
10
20
30
40
50
60
Ambient Temperature (ºC)
70
80
25
50
75
100
Junction Temperature (ºC)
125
150
10
5
400LFM
200LFM
100LFM
Nat Conv
0
0
Figure 2. Power Loss vs Temperature
Output Current (A)
Output Current (A)
Figure 1. Power Loss vs Output Current
−25
90
Figure 3. Safe Operating Area – PCB Vertical Mount(1)
0
400LFM
200LFM
100LFM
Nat Conv
0
10
20
30
40
50
60
Ambient Temperature (ºC)
70
80
90
Figure 4. Safe Operating Area – PCB Horizontal Mount(1)
20
Output Current (A)
15
10
5
0
0
20
40
60
80
100
Board Temperature (ºC)
120
140
Figure 5. Typical Safe Operating Area(1)
(1)
4
The Typical Power Block System Characteristic curves are based on measurements made on a PCB design with
dimensions of 4.0” (W) × 3.5” (L) × 0.062” (H) and 6 copper layers of 1 oz. copper thickness. See Application Section
for detailed explanation.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
TYPICAL POWER BLOCK DEVICE CHARACTERISTICS (continued)
Test Conditions: VIN = 12V, VDD = 5V, fSW = 500kHz, VOUT = 1.3V, LOUT = 1µH, IOUT = 15A, TJ = 125°C, unless stated
otherwise.
17.1
1.5
14.3
1.5
14.3
1.4
11.4
1.4
11.4
1.3
8.6
1.3
8.6
1.2
5.7
1.2
5.7
1.1
2.9
1.1
2.9
1
0.0
1
0.0
0.9
−2.9
0.8
−5.7
0.7
−8.6
350
0.9
−2.9
0.8
−5.7
0.7
−8.6
0.6
−11.4
500 650 800 950 1100 1250 1400 1550
Switching Frequency (kHz)
Figure 6. Normalized Power Loss vs Switching Frequency
3
5
7
11
13
15
Input Voltage (V)
17
19
21
23
−11.4
Figure 7. Normalized Power Loss vs Input Voltage
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
22.5
1.6
16.9
1.7
19.7
1.5
14.1
1.6
16.9
1.4
11.2
1.5
14.1
1.3
8.4
1.4
11.2
1.2
5.6
1.3
8.4
1.1
2.8
1.2
5.6
1.1
2.8
1
0.8
0.5
1
1.5
2
2.5
3
3.5
Output Voltage (V)
4
4.5
5
0
−2.8
0.8
−5.6
−2.8
0.7
−8.4
−5.6
5.5
0.6
Figure 8. Normalized Power Loss vs. Output Voltage
Copyright © 2011–2012, Texas Instruments Incorporated
1
0.9
0
0.9
Power Loss, Normalized
1.8
SOA Temperature Adj (ºC)
Power Loss, Normalized
9
0
0.1
0.2
0.3
0.4 0.5 0.6 0.7 0.8
Output Inductance (µH)
0.9
1
SOA Temperature Adj (ºC)
0.6
200
Power Loss, Normalized
1.6
SOA Temperature Adj (ºC)
TEXT ADDED FOR SPACING
17.2
SOA Temperature Adj (ºC)
Power Loss, Normalized
TEXT ADDED FOR SPACING
1.6
−11.2
1.1
Figure 9. Normalized Power Loss vs. Output Inductance
Submit Documentation Feedback
5
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
TYPICAL POWER BLOCK MOSFET CHARACTERISTICS
TA = 25°C, unless stated otherwise.
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
50
IDS - Drain-to-Source Current - A
IDS - Drain-to-Source Current - A
50
40
30
20
10
0
VGS = 8.0V
VGS = 4.5V
VGS = 4.0V
0
0.2
0.4
0.6
0.8
1
1.2
40
30
20
10
0
1.4
VGS = 8.0V
VGS = 4.5V
VGS = 4.0V
0
0.1
VDS - Drain-to-Source Voltage - V
Figure 10. Control MOSFET Saturation
TEXT ADDED FOR SPACING
IDS - Drain-to-Source Current - A
IDS - Drain-to-Source Current - A
0.6
VDS = 3V
10
1
0.1
0.01
TC = 125°C
TC = 25°C
TC = −55°C
1
1.5
2
2.5
3
3.5
VGS - Gate-to-Source Voltage - V
4
10
1
0.1
0.01
0.001
TC = 125°C
TC = 25°C
TC = −55°C
0
0.5
1
1.5
2
2.5
VGS - Gate-to-Source Voltage - V
3
Figure 13. Sync MOSFET Transfer
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
8
8
ID = 8A
VDD = 15V
7
VGS - Gate-to-Source Voltage (V)
VGS - Gate-to-Source Voltage (V)
0.5
TEXT ADDED FOR SPACING
Figure 12. Control MOSFET Transfer
6
5
4
3
2
1
0
1
2
3
4
Qg - Gate Charge - nC (nC)
Figure 14. Control MOSFET Gate Charge
6
0.4
100
VDS = 3V
0
0.3
Figure 11. Sync MOSFET Saturation
100
0.001
0.2
VDS - Drain-to-Source Voltage - V
Submit Documentation Feedback
5
ID = 8A
VDD = 15V
7
6
5
4
3
2
1
0
0
2
4
6
8
10
Qg - Gate Charge - nC (nC)
Figure 15. Sync MOSFET Gate Charge
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
TYPICAL POWER BLOCK MOSFET CHARACTERISTICS (continued)
TA = 25°C, unless stated otherwise.
TEXT ADDED FOR SPACING
10
0.1
1
C − Capacitance − nF
C − Capacitance − nF
TEXT ADDED FOR SPACING
1
0.01
0.001
Ciss = Cgd + Cgs
Coss = Cds + Cgd
Crss = Cgd
0.0001
0
5
10
0.1
0.01
Ciss = Cgd + Cgs
Coss = Cds + Cgd
Crss = Cgd
f = 1MHz
VGS = 0V
15
20
25
30
0.001
0
5
10
VDS - Drain-to-Source Voltage - V
f = 1MHz
VGS = 0V
15
20
25
Figure 16. Control MOSFET Capacitance
Figure 17. Sync MOSFET Capacitance
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
2
1.6
ID = 250µA
VGS(th) - Threshold Voltage - V
VGS(th) - Threshold Voltage - V
ID = 250µA
1.8
1.6
1.4
1.2
1
0.8
0.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0.4
−75
−25
25
75
125
0
−75
175
−25
TC - Case Temperature - ºC
25
75
125
Figure 19. Sync MOSFET VGS(th)
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
60
15
50
40
30
20
10
TC = 25°C
TC = 125ºC
0
1
2
3
4
5
6
7
8
9
VGS - Gate-to- Source Voltage - V
Figure 20. Control MOSFET RDS(on) vs VGS
Copyright © 2011–2012, Texas Instruments Incorporated
10
ID = 8A
RDS(on) - On-State Resistance - mΩ
ID = 8A
RDS(on) - On-State Resistance - mΩ
175
TC - Case Temperature - ºC
Figure 18. Control MOSFET VGS(th)
0
30
VDS - Drain-to-Source Voltage - V
12
9
6
3
TC = 25°C
TC = 125ºC
0
0
1
2
3
4
5
6
7
8
9
10
VGS - Gate-to- Source Voltage - V
Figure 21. Sync MOSFET RDS(on) vs VGS
Submit Documentation Feedback
7
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
TYPICAL POWER BLOCK MOSFET CHARACTERISTICS (continued)
TA = 25°C, unless stated otherwise.
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
1.8
1.8
Normalized On-State Resistance
1.4
1.2
1
0.8
0.6
0.4
0.2
0
−75
−25
25
75
125
ID = 8A
VGS = 8V
1.6
Normalized On-State Resistance
ID = 8A
VGS = 8V
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
−75
175
−25
TC - Case Temperature - ºC
Figure 22. Control MOSFET Normalized RDS(on)
TEXT ADDED FOR SPACING
0.1
0.01
0.001
TC = 25°C
TC = 125°C
0.4
0.6
0.8
1
1.2
ISD − Source-to-Drain Current - A
ISD − Source-to-Drain Current - A
1
10
1
0.1
0.01
0.001
0.0001
TC = 25°C
TC = 125°C
0
0.2
0.4
0.6
0.8
1
VSD − Source-to-Drain Voltage - V
Figure 24. Control MOSFET Body Diode
Figure 25. Sync MOSFET Body Diode
TEXT ADDED FOR SPACING
TEXT ADDED FOR SPACING
100
I(AV) - Peak Avalanche Current - A
100
I(AV) - Peak Avalanche Current - A
175
TEXT ADDED FOR SPACING
VSD − Source-to-Drain Voltage - V
10
TC = 25°C
TC = 125°C
0.1
1
10
t(AV) - Time in Avalanche - ms
Figure 26. Control MOSFET Unclamped Inductive
Switching
8
125
100
10
1
0.01
75
Figure 23. Sync MOSFET Normalized RDS(on)
100
0.0001
0.2
25
TC - Case Temperature - ºC
Submit Documentation Feedback
10
TC = 25°C
TC = 125°C
1
0.01
0.1
1
10
t(AV) - Time in Avalanche - ms
Figure 27. Sync MOSFET Unclamped Inductive Switching
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
APPLICATION INFORMATION
Equivalent System Performance
Many of today’s high performance computing systems require low power consumption in an effort to reduce
system operating temperatures and improve overall system efficiency. This has created a major emphasis on
improving the conversion efficiency of today’s Synchronous Buck Topology. In particular, there has been an
emphasis in improving the performance of the critical Power Semiconductor in the Power Stage of this
Application (see Figure 28). As such, optimization of the power semiconductors in these applications, needs to
go beyond simply reducing RDS(ON).
Figure 28.
The CSD87331Q3D is part of TI’s Power Block product family which is a highly optimized product for use in a
synchronous buck topology requiring high current, high efficiency, and high frequency. It incorporates TI’s latest
generation silicon which has been optimized for switching performance, as well as minimizing losses associated
with QGD, QGS, and QRR. Furthermore, TI’s patented packaging technology has minimized losses by nearly
eliminating parasitic elements between the Control FET and Sync FET connections (see Figure 29). A key
challenge solved by TI’s patented packaging technology is the system level impact of Common Source
Inductance (CSI). CSI greatly impedes the switching characteristics of any MOSFET which in turn increases
switching losses and reduces system efficiency. As a result, the effects of CSI need to be considered during the
MOSFET selection process. In addition, standard MOSFET switching loss equations used to predict system
efficiency need to be modified in order to account for the effects of CSI. Further details behind the effects of CSI
and modification of switching loss equations are outlined in TI’s Application Note SLPA009.
Figure 29.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
96
4
94
3.5
92
3
90
VGS = 5V
VIN = 12V
VOUT = 1.3V
LOUT = 1µH
fSW = 500kHz
TA = 25ºC
88
86
84
0
2
4
PowerBlock HS/LS RDS(ON) = 18mΩ/6.7mΩ
Discrete HS/LS RDS(ON) = 18mΩ/6.7mΩ
Discrete HS/LS RDS(ON) = 18mΩ/5.5mΩ
VGS = 5V
VIN = 12V
VOUT = 1.3V
LOUT = 1µH
fSW = 500kHz
TA = 25ºC
2.5
2
1.5
1
PowerBlock HS/LS RDS(ON) = 18mΩ/6.7mΩ
Discrete HS/LS RDS(ON) = 18mΩ/6.7mΩ
Discrete HS/LS RDS(ON) = 18mΩ/5.5mΩ
82
80
Power Loss (W)
Efficiency (%)
The combination of TI’s latest generation silicon and optimized packaging technology has created a
benchmarking solution that outperforms industry standard MOSFET chipsets of similar RDS(ON) and MOSFET
chipsets with lower RDS(ON). Figure 30 and Figure 31 compare the efficiency and power loss performance of the
CSD87331Q3D versus industry standard MOSFET chipsets commonly used in this type of application. This
comparison purely focuses on the efficiency and generated loss of the power semiconductors only. The
performance of CSD87331Q3D clearly highlights the importance of considering the Effective AC On-Impedance
(ZDS(ON)) during the MOSFET selection process of any new design. Simply normalizing to traditional MOSFET
RDS(ON) specifications is not an indicator of the actual in-circuit performance when using TI’s Power Block
technology.
6
8
10
Output Current (A)
12
0.5
14
16
0
0
2
4
Figure 30.
6
8
10
Output Current (A)
12
14
16
Figure 31.
The chart below compares the traditional DC measured RDS(ON) of CSD87331Q3D versus its ZDS(ON). This
comparison takes into account the improved efficiency associated with TI’s patented packaging technology. As
such, when comparing TI’s Power Block products to individually packaged discrete MOSFETs or dual MOSFETs
in a standard package, the in-circuit switching performance of the solution must be considered. In this example,
individually packaged discrete MOSFETs or dual MOSFETs in a standard package would need to have DC
measured RDS(ON) values that are equivalent to CSD87331Q3D’s ZDS(ON) value in order to have the same
efficiency performance at full load. Mid to light-load efficiency will still be lower with individually packaged discrete
MOSFETs or dual MOSFETs in a standard package.
Comparison of RDS(ON) vs. ZDS(ON)
Parameter
10
HS
Typ
LS
Max
Typ
Max
Effective AC On-Impedance ZDS(ON) (VGS = 5V)
18
-
5.5
-
DC Measured RDS(ON) (VGS = 4.5V)
18
22
6.7
8
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
The CSD87331Q3D NexFET™ power block is an optimized design for synchronous buck applications using 5V
gate drive. The Control FET and Sync FET silicon are parametrically tuned to yield the lowest power loss and
highest system efficiency. As a result, a new rating method is needed which is tailored towards a more systems
centric environment. System level performance curves such as Power Loss, Safe Operating Area, and
normalized graphs allow engineers to predict the product performance in the actual application.
Power Loss Curves
MOSFET centric parameters such as RDS(ON) and Qgd are needed to estimate the loss generated by the devices.
In an effort to simplify the design process for engineers, Texas Instruments has provided measured power loss
performance curves. Figure 1 plots the power loss of the CSD87331Q3D as a function of load current. This curve
is measured by configuring and running the CSD87331Q3D as it would be in the final application (see
Figure 32).The measured power loss is the CSD87331Q3D loss and consists of both input conversion loss and
gate drive loss. Equation 1 is used to generate the power loss curve.
(VIN × IIN) + (VDD × IDD) – (VSW_AVG × IOUT) = Power Loss
(1)
The power loss curve in Figure 1 is measured at the maximum recommended junction temperatures of 125°C
under isothermal test conditions.
Safe Operating Curves (SOA)
The SOA curves in the CSD87331Q3D data sheet provides guidance on the temperature boundaries within an
operating system by incorporating the thermal resistance and system power loss. Figure 3 to Figure 5 outline the
temperature and airflow conditions required for a given load current. The area under the curve dictates the safe
operating area. All the curves are based on measurements made on a PCB design with dimensions of 4” (W) ×
3.5” (L) × 0.062” (T) and 6 copper layers of 1 oz. copper thickness.
Normalized Curves
The normalized curves in the CSD87331Q3D data sheet provides guidance on the Power Loss and SOA
adjustments based on their application specific needs. These curves show how the power loss and SOA
boundaries will adjust for a given set of systems conditions. The primary Y-axis is the normalized change in
power loss and the secondary Y-axis is the change is system temperature required in order to comply with the
SOA curve. The change in power loss is a multiplier for the Power Loss curve and the change in temperature is
subtracted from the SOA curve.
Figure 32. Typical Application
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
Calculating Power Loss and SOA
The user can estimate product loss and SOA boundaries by arithmetic means (see Design Example). Though
the Power Loss and SOA curves in this data sheet are taken for a specific set of test conditions, the following
procedure will outline the steps the user should take to predict product performance for any set of system
conditions.
Design Example
Operating Conditions:
• Output Current = 10A
• Input Voltage = 10V
• Output Voltage = 1V
• Switching Frequency = 1000kHz
• Inductor = 0.4µH
Calculating Power Loss
•
•
•
•
•
•
Power Loss at 10A = 1.8W (Figure 1)
Normalized Power Loss for input voltage ≈ 1.0 (Figure 7)
Normalized Power Loss for output voltage ≈ 0.95 (Figure 8)
Normalized Power Loss for switching frequency ≈ 1.15 (Figure 6)
Normalized Power Loss for output inductor ≈ 1.04 (Figure 9)
Final calculated Power Loss = 1.8W × 1.0 × 0.95 × 1.15 × 1.04 ≈ 2.05W
Calculating SOA Adjustments
•
•
•
•
•
SOA adjustment for input voltage ≈ 0.1ºC (Figure 7)
SOA adjustment for output voltage ≈ -1.3ºC (Figure 8)
SOA adjustment for switching frequency ≈ 4.2ºC (Figure 6)
SOA adjustment for output inductor ≈ 1ºC (Figure 9)
Final calculated SOA adjustment = 0.1 + (–1.3) + 4.2 + 1 ≈ 4.8ºC
In the design example above, the estimated power loss of the CSD87331Q3D would increase to 2.05W. In
addition, the maximum allowable board and/or ambient temperature would have to decrease by 4.8ºC. Figure 33
graphically shows how the SOA curve would be adjusted accordingly.
1. Start by drawing a horizontal line from the application current to the SOA curve.
2. Draw a vertical line from the SOA curve intercept down to the board/ambient temperature.
3. Adjust the SOA board/ambient temperature by subtracting the temperature adjustment value.
In the design example, the SOA temperature adjustment yields a reduction in allowable board/ambient
temperature of 4.8ºC. In the event the adjustment value is a negative number, subtracting the negative number
would yield an increase in allowable board/ambient temperature.
20
Output Current (A)
15
1
10
2
5
3
0
0
20
40
60
80
100
Board Temperature (°C)
120
140
Figure 33. Power Block SOA
12
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
RECOMMENDED PCB DESIGN OVERVIEW
There are two key system-level parameters that can be addressed with a proper PCB design: Electrical and
Thermal performance. Properly optimizing the PCB layout will yield maximum performance in both areas. A brief
description on how to address each parameter is provided.
Electrical Performance
The Power Block has the ability to switch voltages at rates greater than 10kV/µs. Special care must be then
taken with the PCB layout design and placement of the input capacitors, Driver IC, and output inductor.
• The placement of the input capacitors relative to the Power Block’s VIN and PGND pins should have the
highest priority during the component placement routine. It is critical to minimize these node lengths. As such,
ceramic input capacitors need to be placed as close as possible to the VIN and PGND pins (see Figure 34).
The example in Figure 34 uses 6 × 10-µF ceramic capacitors (TDK Part # C3216X5R1C106KT or equivalent).
Notice there are ceramic capacitors on both sides of the board with an appropriate amount of vias
interconnecting both layers. In terms of priority of placement next to the Power Block, C5, C7, C19, and C8
should follow in order.
• The Driver IC should be placed relatively close to the Power Block Gate pins. TG and BG should connect to
the outputs of the Driver IC. The TGR pin serves as the return path of the high-side gate drive circuitry and
should be connected to the Phase pin of the IC (sometimes called LX, LL, SW, PH, etc.). The bootstrap
capacitor for the Driver IC will also connect to this pin.
• The switching node of the output inductor should be placed relatively close to the Power Block VSW pins.
Minimizing the node length between these two components will reduce the PCB conduction losses and
actually reduce the switching noise level. (1) In the event the switch node waveform exhibits ringing that
reaches undesirable levels, the use of a Boost Resistor or RC snubber can be an effective way to easily
reduce the peak ring level. The recommended Boost Resistor value will range between 1.0 Ohms to 4.7
Ohms depending on the output characteristics of Driver IC used in conjunction with the Power Block. The RC
snubber values can range from 0.5 Ohms to 2.2 Ohms for the R and 330pF to 2200pF for the C. Please refer
to TI App Note SLUP100 for more details on how to properly tune the RC snubber values. The RC snubber
should be placed as close as possible to the Vsw node and PGND see Figure 34 (1)
(1)
(1) Keong W. Kam, David Pommerenke, “EMI Analysis Methods for Synchronous Buck Converter EMI Root Cause Analysis”, University
of Missouri – Rolla
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
13
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
Thermal Performance
The Power Block has the ability to utilize the GND planes as the primary thermal path. As such, the use of
thermal vias is an effective way to pull away heat from the device and into the system board. Concerns of solder
voids and manufacturability problems can be addressed by the use of three basic tactics to minimize the amount
of solder attach that will wick down the via barrel:
• Intentionally space out the vias from each other to avoid a cluster of holes in a given area.
• Use the smallest drill size allowed in your design. The example in Figure 34 uses vias with a 10 mil drill hole
and a 16 mil capture pad.
• Tent the opposite side of the via with solder-mask.
In the end, the number and drill size of the thermal vias should align with the end user’s PCB design rules and
manufacturing capabilities.
Figure 34. Recommended PCB Layout (Top Down)
14
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
MECHANICAL DATA
Q3D Package Dimensions
A
E2
E1
5
9
2
7
2
D2
7
D1
E
d
e
8
1
1
8
Top View
Side View
d2
Pin 1
Designation
VIN
Pin 2
VIN
Pin 3
TG
Pin 4
TGR
Pin 5
BG
Pin 6
VSW
Pin 7
VSW
Pin 8
VSW
Pin 9
PGND
DIM
d3
K
Bottom View
Pinout
Position
b
6
4
3
6
4
5
3
q
L
d1
L
c1
c
Exposed tie clips may vary
q
M0192-01
MILLIMETERS
INCHES
MIN
MAX
MIN
MAX
A
1.40
1.5
0.055
0.059
b
0.280
0.400
0.011
0.016
c
0.150
0.250
0.006
0.010
c1
0.150
0.250
0.006
0.010
d
0.940
1.040
0.037
0.041
d1
0.160
0.260
0.006
0.010
d2
0.150
0.250
0.006
0.010
d3
0.250
0.350
0.010
0.014
D1
3.200
3.400
0.126
0.134
D2
2.650
2.750
0.104
0.108
E
3.200
3.400
0.126
0.134
E1
3.200
3.400
0.126
0.134
E2
1.750
1.850
0.069
e
0.650 TYP
L
0.400
θ
0.00
K
Copyright © 2011–2012, Texas Instruments Incorporated
0.300 TYP
0.073
0.026 TYP
0.500
0.016
–
–
0.020
–
0.012 TYP
Submit Documentation Feedback
15
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
Land Pattern Recommendation
1.900 (0.075)
0.200
(0.008)
0.210
(0.008)
4
0.350 (0.014)
5
0.440
(0.017)
0.650
(0.026)
2.800
(0.110)
2.390
(0.094)
8
0.210
(0.008)
1
1.090
(0.043)
0.300 (0.012)
0.650 (0.026)
0.650 (0.026)
3.600 (0.142)
M0193-01
NOTE: Dimensions are in mm (inches).
Stencil Recommendation
0.160 (0.005)
0.550 (0.022)
0.200 (0.008)
5
4
0.300 (0.012)
0.300
(0.012)
0.340
(0.013)
2.290
(0.090)
0.333
(0.013)
8
1
0.990
(0.039)
0.100
(0.004)
0.300 (0.012)
0.350 (0.014)
0.850 (0.033)
3.500 (0.138)
M0207-01
NOTE: Dimensions are in mm (inches).
For recommended circuit layout for PCB designs, see application note SLPA005 – Reducing Ringing Through
PCB Layout Techniques.
16
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
CSD87331Q3D
SLPS283A – SEPTEMBER 2011 – REVISED JANUARY 2012
www.ti.com
1.75 ±0.10
Q3D Tape and Reel Information
4.00 ±0.10 (See Note 1)
Ø 1.50
+0.10
–0.00
1.30
3.60
5.50 ±0.05
12.00
+0.30
–0.10
8.00 ±0.10
2.00 ±0.05
3.60
M0144-01
NOTES: 1. 10-sprocket hole-pitch cumulative tolerance ±0.2
2. Camber not to exceed 1mm in 100mm, noncumulative over 250mm
3. Material: black static-dissipative polystyrene
4. All dimensions are in mm, unless otherwise specified.
5. Thickness: 0.30 ±0.05mm
6. MSL1 260°C (IR and convection) PbF reflow compatible
Spacer
REVISION HISTORY
Changes from Original (September 2011) to Revision A
•
Page
Added Feature Bullet: Up to 15A Operation ......................................................................................................................... 1
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
PACKAGE OPTION ADDENDUM
www.ti.com
10-May-2012
PACKAGING INFORMATION
Orderable Device
CSD87331Q3D
Status
(1)
ACTIVE
Package Type Package
Drawing
SON
DQZ
Pins
Package Qty
8
2500
Eco Plan
(2)
Pb-Free (RoHS
Exempt)
Lead/
Ball Finish
CU SN
MSL Peak Temp
(3)
Samples
(Requires Login)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-May-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CSD87331Q3D
Package Package Pins
Type Drawing
SON
DQZ
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.8
Pack Materials-Page 1
3.6
B0
(mm)
K0
(mm)
P1
(mm)
3.6
1.75
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-May-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CSD87331Q3D
SON
DQZ
8
2500
335.0
335.0
32.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated