OPI2000MTH This component is RoHS compliant High Speed Opto Isolator Through Hole ATEX & IECEx Certified Pb The OPI 2000MTH High Speed Optically Coupled Isolator consists of a High Speed Infrared emitter coupled to a silicon photo I.C. The unit is designed for applications requiring high voltage isolation between input & output . • 10KV isolation • Low Propagation Delay • High Speed 2Mb/sec. • Short housing • Through Hole configuration CERTIFICATE ATEX BAS01ATEX1285U/5 CERTIFICATE IECEx BAS 06.0021U/4 Confirmed conform to:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / Details repeated on Page 2 of this datasheet. Confirmed conform to:IEC 60079-0:2011 Edition 6 IEC 60079-11:2011 Edition 6 IEC 60079-26:2006 Edition 2 Conditions of use apply:- See Schedule of limitations on certificate / Details repeated on Page 2 of this datasheet. MECHANICAL DATA 14.45-0.0+0.2 6.65 9.25 2.7 Emitter 0.4x0.45 0.4 10.50-0.0+0.2 SENSOR 0.5 SQ 0.5 2.54 1.91 1.91 GRD An K PIN OUT (TOP VIEW) Vout Vcc BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 1/4 Iss H 20.10.12 OPI2000MTH This component is RoHS compliant Pb ABSOLUTE MAXIMUM RATINGS (25OC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 100mA 5 Volts 150mW (ii) OUTPUT IC MAX SUPPLY VOLTAGE POWER DISSIPATION 7 Volts 165mW OPERATING TEMP -40 OC TO +80 OC STORAGE TEMP -40 OC TO +80 OC LEAD SOLDERING TEMP 2mm from body 5 secs max INPUT-TO-OUTPUT ISOLATION VOLTAGE 260 OC + 10KV DC (i) NOTES i) Measured with the input leads and output leads shorted together for one min. ii) Thermal resistance 450 K/W Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of the need to increase the diode current to trigger the device over long periods at high temperatures & currents. SCHEDULE OF LIMITATIONS EC TYPE EX AMIN ATION CERTIFICATE No. BAS01 ATEX1285U/5 28th September 2012 SCHEDULE OF LIMITATIONS 1) - The surface mounted Opto Is olator OPI2000M must be mounted on a p.c.b. having a CTI of at least 175 so that creepage and clearanc e distances are not impaired. The surface mounted device is designed for the pins to be s oldered to the pads on the same si de of the printed circuit board as the c omponent and must onl y be used either:a) on a printed circuit board which is potted provi ded that the pad s egregation mai ntains at least 2mm under potting. OR b) on a printed circuit board which is c oated provided that the pad segregation mainyains at least 3.3mm under coating. Where the coating shall seal the connections after s oldering and s hall be two coats if applied by s praying OR a single coat if dipped, brus hed or vacuum i mpregnated. A CTI of at least 175 shall appl y to both the pc b substrate and the coating material. This c ondition 1), does not apply to the thr ough hole version, OPI2000MTH for voltages up to 375V peak or d.c. provided that the mounti ng arrangement does not reduce the creepage distances to less than 10mm. 2) - The Opto Isol ators OPI2000M and OPI2000MTH may be us ed to provide isolati on between either:(i) A non-intrinsically s afe circuit and an intrinsicall y safe circuit, (Non IS:IS), where the IS circuit voltage is not greater than 75 Volts peak or d.c .. OR (ii) Two intrinsicall y safe circuits (IS:IS), where the sum of the two circuit voltages is not greater than 375 Volts peak or d.c.. 3) - The Opto Isol ators OPI2000M and OPI2000MTH must be ins talled suc h that the connection pins are provided with a degree of protection of at least IP20 where gass es and vapours may be pres ent. If the Opto Is olators are to be i nstalled where dusts r epres ent a hazar d, then it must be pr ovi ded with a degree of protec tion of at l east IP54 and the overall apparatus must be appropriatel y certified for the requirements for Dusts. 4) - The Opto Isol ators OPI2000M and OPI2000MTH must be ins talled with external power limiting components as s pecifi ed in:EN60079-11:2012, Claus e 8.9.2. CERTIFICATE No.:- IECEx BAS 06.0021U Date of Issue:- 2012-10-02 ISSUE No.: 4 SCHEDULE OF LIMITATIONS 1. When used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the opto-isolator:2. The Opto Isolator must be mounted on a printed circuit board such that creepage and clearance distances are not impaired. 3. The Opto Coupler must be installed such that the connection pins are provided with a degree of protection of IP20 where gasses and vapours may be present. If the Opto Coupler is to be installed within apparatus where flammable dusts represent the hazard then it must be provide with a degree of protection of IP54 and the apparatus must be appropriately certified for dust hazards. 4. Surface Mount OPI2000M only and in addition to above: The surf ace mount OPI2000M must only be used on a printed circuit board that is either: a) potted, providing the pad segregation remains at least 2mm under the potting OR b) conf ormally coated, prov ided the pad segregation remains at least 3.3mm under the coating. The conf ormal coating must hav e CTI in excess of 175. 5. The Opto Isolator must be installed with external power limiting components as specif ied in:- IEC60079-11:2011 Ed 6, Clause 8.9.2. BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 2/4 Iss H 20.10.12 OPI2000MTH This component is RoHS compliant CIRCUIT GND + Vgen Pb + Rf Vout RL C Vcc R L=560 ohm C=0.01uF OPTO ELECTRONIC DATA (TA = 25OC) PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage VF - 1.35 1.6 V If=100mA tp=20mS Rev erse Voltage VR 5.0 - - V Ir = 100uA INPUT DIODE OUTPUT IC ( Vcc=4.75 to 5.25 ) High level Output Current I CH - 100 uA Ic = 10 uA Low Lev el Output Voltage VOL - 0.6 V IF= 10mA IOL= 2.6mA High Lev el Supply Current ICCH 15 mA IF=0 Low Lev el Supply Current ICCL 18 mA IF=7.5mA Propagation Delay to Low Output level t PLH 800 nSecs R L= 560ohms C=0.01uF Propagation Delay to High Output Level t PHL 800 nSecs ditto Input/Output Isolation Voltage Vi-o Volts Input and output leads shorted COUPLED(Vcc=5volts) 10kV OPTO ELECTRONIC SOLUTIONS BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 3/4 Iss H 20.10.12 OPI 2000MTH CONFORMITY STATEMENT OPI2000MTH This component is RoHS compliant Pb Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1285U – Latest supplement BAS01ATEX1285 U/5 issued Sept. 2012 Provisions of the Directive fulfilled by the component:Ex ia IIC Ga (-40°C ≤ Ta ≤ +80°C) II 1 GD Ex ia IIIC Da (-40°C ≤ Ta ≤ +80°C) Notified Body for EC-Type Examination BASEEFA Ltd. Rockhead Business Park, Staden Lane, Buxton, Derbyshire SK17 9RZ, England & Production:- BASEEFA Ltd. – No.1180 Tel:- +44 (0)1298 766600 Fax:- +44 (0)1298 766601 e-mail:- [email protected] Harmonised Standards used:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Other Standards used:- On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory requirements of the ATEX Directive 94/9/EC and the RoHS Directive 2011/65/EU. _______________________________ Mr R.W.Stott PPManaging Director 4/4 Iss H 20.10.12