D100VHI Series Miniature, 1W SIP Ultra-High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • 3.0 kVAC rms Isolation • EN 60950 Approved (UL) • Miniature SIP Case • Single & Dual Outputs • 12 Standard Models • 2.0 MH MTBF • Industry Standard Pin-Out Input Parameter Conditions Input Voltage Range Input Filter Reverse Polarity Input Current Min. 5 VDC Input 4.5 12 VDC Input 10.8 LC Filter Typ. 5.0 12.0 Max. 5.5 13.2 Units 0.3 A Max. ±3.0 ±1.0 ±1.5 Units % % % 150 200 15 ±0.02 mV P - P mV P - P mV rms %/°C Typ. Max. 50 15 80 20 100 Units VAC rms VPk G pF kHz Min. -25 Typ. +25 Max. +85 +90 +125 Units °C °C °C 95 % VDC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz), See Note 2 Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit Conditions Min. Typ. ±1.0 Dual Output , Balanced Loads ±0.1 For Vin Change of 1% ±1.2 See Model Selection Guide 100 Over Line, Load & Temp. ±0.01 Momentary (0.5 Sec.) General Parameter Isolation Voltage Isolation Test Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds Flash Tested for 1 Sec 500 VDC 100 kHz, 1V Min. 3,000 4,500 10 Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Ambient Case -50 Free Air Convection RH, Non-condensing 0.87 x 0.30 x 0.49 Inches (22.0 x 7.5 x 12.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.13 Oz (3.9g) Reliability Specifications Parameter MTBF Safety Approvals Conditions Min. Typ. MIL HDBK 217F, 25°C, Gnd Benign 2.0 UL 60950, EN 60950 Max. Units MHours Max. 9.0 29.0 260 650 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 Typ. Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C mW www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Output Current (mA) Full-Load No-Load Voltage Current Current (VDC) (mA, Max) (mA, Min) Load ciency Regulation Effi (%, Typ) (%, Max) Fuse Rating Slow-Blow (mA) Nominal Range D101VHI 5 4.5 - 5.5 303 55 5.0 200.0 4.0 10 66 500 D102VHI 5 4.5 - 5.5 291 55 12.0 80.0 2.0 8 66 500 D103VHI 5 4.5 - 5.5 295 55 15.0 65.0 1.0 8 66 500 D104VHI 5 4.5 - 5.5 303 55 ±5.0 ±100.0 ±2.0 10 66 500 D105VHI 5 4.5 - 5.5 267 55 ±12.0 ±40.0 ±1.0 8 72 500 D106VHI 5 4.5 - 5.5 287 55 ±15.0 ±35.0 ±1.0 8 73 500 D111VHI 12 10.8 - 13.2 126 30 5.0 200.0 4.0 10 66 200 D112VHI 12 10.8 - 13.2 121 30 12.0 80.0 2.0 8 66 200 D113VHI 12 10.8 - 13.2 123 30 15.0 65.0 1.0 8 66 200 D114VHI 12 10.8 - 13.2 126 30 ±5.0 ±100.0 ±2.0 10 66 200 D115VHI 12 10.8 - 13.2 108 30 ±12.0 ±40.0 ±1.0 8 74 200 D116VHI 12 10.8 - 13.2 117 30 ±15.0 ±35.0 ±1.0 8 75 200 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recomended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 5 -Vout -Vout 6 No Pin Common 7 +Vout +Vout NC: No Connection Capacitive Load Single Output Dual Output µF Max µF Max 680 ±220 Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]