D200 Series Single & Dual Output Miniature, 2W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • Miniature SIP Case • Single & Dual Outputs • 1,000 VDC Isolation • >1.12 MHour MTBF • 28 Standard Models • Industry Standard Pin-Out Input Parameter Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 Internal Capacitor 12 µH Source Inductance Input Voltage Range Input Filter Reflected Ripple Current Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 20 Units VDC mA P - P Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. ±3.0 Dual Output , Balanced Loads ±1.0 For Vin Change of 1% ±1.2 See Model Selection Guide 75 120 Max. ±0.02 Units % % % mV P - P % %/ºC Momentary (0.5 Sec.) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 Typ. Max. Units VDC M⍀ pF kHz Max. +85 +100 +125 Units ºC ºC ºC 95 % 60 80 Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size (5V, 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight Reliability Specifications Parameter MTBF Conditions Ambient Case Min. -40 Typ. +25 -40 Free Air Convection RH, Non-condensing 0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm) 0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.08 Oz (2.3g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 1.12 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 7.0 15.0 28.0 54.0 260 650 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC ºC mW www.micropowerdirect.com Model Selection Guide Model Number D201 D202 D203 D204 D205 D206 D207 D211 D212 D213 D214 D215 D216 D217 D221 D222 D223 D224 D225 D226 D227 D231 D232 D233 D234 D235 D236 D237 Input Voltage (VDC) Nominal Range 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 Output Current (mA) Voltage Current Current Full-Load No-Load (VDC) (mA, Max) (mA, Min) 367 30 3.3 400.0 10.0 512 30 5.0 400.0 8.0 500 30 12.0 165.0 3.5 500 30 15.0 133.0 2.7 555 30 ±5.0 ±200.0 ±4.0 512 30 ±12.0 ±83.3 ±1.7 500 30 ±15.0 ±66.6 ±1.4 169 20 3.3 400.0 10.0 216 20 5.0 400.0 8.0 203 20 12.0 165.0 3.5 203 20 15.0 133.0 2.7 222 20 ±5.0 ±200.0 ±4.0 203 20 ±12.0 ±83.3 ±1.7 203 20 ±15.0 ±66.6 ±1.4 76 10 3.3 400.0 10.0 105 10 5.0 400.0 8.0 102 10 12.0 165.0 3.5 101 10 15.0 133.0 2.7 111 10 ±5.0 ±200.0 ±4.0 101 10 ±12.0 ±83.3 ±1.7 101 10 ±15.0 ±66.6 ±1.4 45 6 3.3 400.0 10.0 54 6 5.0 400.0 8.0 53 6 12.0 165.0 3.5 53 6 15.0 133.0 2.7 57 6 ±5.0 ±200.0 ±4.0 52 6 ±12.0 ±83.3 ±1.7 52 6 ±15.0 ±66.6 ±1.4 Load Regulation (%, Max) 20 10 10 10 10 10 10 20 10 10 10 10 10 10 20 10 10 10 10 10 10 20 10 10 10 10 10 10 72 78 82 82 72 78 80 65 77 82 82 75 82 82 72 79 80 82 75 82 82 60 77 78 78 73 80 80 Pin Connections Capacitive Load Other input/output combinations are available (i.e. 24.0 VDC). Contact the factory for details at: [email protected] Single Output (µF Max) 470 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. These units do not require external components to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. It is recommended that an input capacitor of 4.7 µF to 47µF (dependent upon the application) be used on 48V input model. An output capacitor (4.7 µF to 220 µF or ±4.7 µF to ±100 µF) may be used to reduce ripple. To improve EMI performance, a simple filter network consisting of a 10 µF to 100 µF capacitor and 12 µH inductor should be effective. 3. These units will operate at no load without damage, but may not meet all specifications. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 200 200 200 200 200 200 200 100 100 100 100 100 100 100 Efficiency (%, Typ) Dual Output (µF Max) Pin Single Dual 1 2 4 5 6 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout ±220 Mechanical Dimensions Derating Curve MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit FAX: (781) 344-8481 • E-Mail: [email protected]