FDC20 FDC20W SERIES DC-DC CONVERTER 2:1 & 4:1 WIDE INPUT RANGE UP TO 20 WATTS FEATURES APPLICATIONS • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.60 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL OCP SCP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25 Model Number FDC20-12S33 FDC20-12S05 FDC20-12S12 FDC20-12S15 FDC20-12D05 FDC20-12D12 FDC20-12D15 FDC20-12T3312 FDC20-12T3315 FDC20-12T0512 FDC20-12T0515 FDC20-24S33 FDC20-24S05 FDC20-24S12 FDC20-24S15 FDC20-24D05 FDC20-24D12 FDC20-24D15 FDC20-24T3312 FDC20-24T3315 FDC20-24T0512 FDC20-24T0515 FDC20-48S33 FDC20-48S05 FDC20-48S12 FDC20-48S15 FDC20-48D05 FDC20-48D12 FDC20-48D15 FDC20-48T3312 FDC20-48T3315 FDC20-48T0512 FDC20-48T0515 1 Input Range Output Voltage VDC VDC 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 3.3 5 12 15 ±5 ±12 ±15 3.3 / ±12 3.3 / ±15 5 / ±12 5 / ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 / ±12 3.3 / ±15 5 / ±12 5 / ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 / ±12 3.3 / ±15 5 / ±12 5 / ±15 Output Current @Full Load Min. Load (1) mA 280 280 134 106 ±140 ±67 ±53 300 / ±30 300 / ±25 200 / ±30 200 / ±25 280 280 134 106 ±140 ±67 ±53 300 / ±30 300 / ±25 200 / ±30 200 / ±25 280 280 134 106 ±140 ±67 ±53 300 / ±30 300 / ±25 200 / ±30 200 / ±25 Full Load mA 4000 4000 1670 1330 ± 2000 ± 833 ± 666 3000 / ±300 3000 / ±250 2000 / ±300 2000 / ±250 4000 4000 1670 1330 ± 2000 ± 833 ± 666 3000 / ±300 3000 / ±250 2000 / ±300 2000 / ±250 4000 4000 1670 1330 ± 2000 ± 833 ± 666 3000 / ±300 3000 / ±250 2000 / ±300 2000 / ±250 www.PDUKE.com otherwise noted Input Current @ No Load Efficiency Maximum Capacitor Load (2) mA % µF 40 15 40 20 15 35 35 20 35 20 40 10 10 10 15 20 25 30 20 20 25 10 10 10 15 25 15 15 20 10 10 15 15 77 80 83 84 82 83 83 79 79 80 80 79 81 86 86 85 86 86 82 79 83 83 79 82 86 86 85 87 87 82 82 84 84 13000 6800 2200 755 ±3400 ±680 ±450 4700 / ±220 4700 / ±220 4700 / ±220 4700 / ±220 13000 6800 2200 755 ±3400 ±680 ±450 4700 / ±220 4700 / ±220 4700 / ±220 4700 / ±220 13000 6800 2200 755 ±3400 ±680 ±450 4700 / ±220 4700 / ±220 4700 / ±220 4700 / ±220 2015/2/26 Model Number FDC20-24S33W FDC20-24S05W FDC20-24S12W FDC20-24S15W FDC20-24D05W FDC20-24D12W FDC20-24D15W FDC20-48S33W FDC20-48S05W FDC20-48S12W FDC20-48S15W FDC20-48D05W FDC20-48D12W FDC20-48D15W Input Range Output Voltage VDC VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 Output Current @Full Load Min. Load (1) mA 280 280 134 106 ±140 ±67 ±53 280 280 134 106 ±140 ±67 ±53 Input Current @ No Load Efficiency Maximum Capacitor Load (2) mA % µF 20 10 20 20 15 20 25 15 10 10 10 10 15 20 76 79 81 81 79 82 82 77 80 82 82 81 83 83 Full Load mA 4000 4000 1670 1330 ± 2000 ± 833 ± 666 4000 4000 1670 1330 ± 2000 ± 833 ± 666 13000 6800 2200 755 ±3400 ±680 ±450 13000 6800 2200 755 ±3400 ±680 ±450 PART NUMBER STRUCTURE FDC20 - Series name 48 Input Voltage (VDC) 12: 9~18 24: 18~36 48: 36~75 S 05 Output Quantity Output Voltage (VDC) S: Single D: Dual T: Triple FDC20 - Series name 48 Input Voltage (VDC) 24: 9~36 48: 18~75 33: 05: 12: 15: 05: 12: 15: 3312: 3315: 0512: 0515: 05 Output Quantity Output Voltage (VDC) D: Dual INPUT SPECIFICATIONS Parameter Operating input voltage range 33: 05: 12: 15: HS Assembly Option : No Assembly Option HS: Heat-sink HC: Heat-sink & Clamp 3.3 5 12 15 ±5 ±12 ±15 3.3 / ±12 3.3 / ±15 5 / ±12 5 / ±15 S S: Single - 3.3 5 12 15 W Input Range Assembly Option : No Assembly Option HS: Heat-sink HC: Heat-sink & Clamp 4:1 05: ±5 12: ±12 15: ±15 Conditions FDC20 series FDC20W series 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Input reflected ripple current Start up time Input surge voltage Constant resistive load 100 ms, max. Power up 12Vin(nom) 24Vin(nom) 48Vin(nom) Input filter Remote ON/OFF Referred to –Vin pin Positive logic OUTPUT SPECIFICATIONS Parameter Voltage accuracy 2 HS DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current Conditions Min. Typ. Max. 9 18 36 9 18 12 24 48 24 48 25 20 18 36 75 36 75 -0.5 Min. Single / Dual Triple: 3.3Vout, 5Vout www.PDUKE.com -1.0 -1.0 Unit VDC VDC mAp-p ms 36 VDC 50 100 Pi type Open or 3.5 ~ 12VDC Short or 0 ~ 1.2VDC +1.0 mA 20 mA Typ. Max. Unit +1.0 +1.0 % 2015/2/26 Line regulation Load regulation Cross regulation Voltage adjustability Ripple and noise Temperature coefficient Transient response recovery time Over voltage protection Over load protection Short circuit protection Low Line to High Line at Full Load Min. Load to Full Load Dual: Asymmetrical load 25%/100% FL Triple: Main output:(3.3Vout, 5Vout) 100% load, auxiliary 100%, other auxiliary 25% to 100% load. Measured by 20MHz bandwidth +5.0 +0.2 +0.5 +1.0 +5.0 +0.5 +3.0 +2.0 +5.0 +5.0 +2.0 +5.0 +10 75 100 50 120 150 Single / Dual Triple 3.3Vout 5Vout 12Vout 15Vout Zener diode clamp % of Iout rated 1 minute Isolation resistance Isolation capacitance Switching frequency Safety approvals 500VDC +0.02 250 500 3.9 6.2 15 18 % % %/ºC µs VDC Conditions Min. Input to Output Input (Output) to Case 1600 1600 1 MIL-HDBK-217F, Full load Conditions Min. With derating Typ. Without heat-sink With heat-sink Unit VDC GΩ pF 300 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper Non-conductive black plastic Epoxy (UL94 V-0) 48g (1.69oz) 1.922 x 106 hrs 300 330 Typ. -40 -55 Vertical direction by natural convection (20LFM) Max. Max. Unit +85 +100 +125 ºC 10 8.24 ºC ºC/W Thermal shock Vibration Relative humidity MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (3) ESD Radiated immunity Fast transient (4) Surge (4) Conducted immunity % 150 % Continuous, automatics recovery 270 ENVIRONMENTAL SPECIFICATIONS Parameter % mVp-p -0.02 Isolation voltage Operating ambient temperature Maximum case temperature Storage temperature range Thermal impedance -5.0 -0.2 -0.5 -1.0 -5.0 -0.5 -3.0 -2.0 -5.0 -5.0 -2.0 -5.0 -10 Single Dual Triple: 3.3Vout, 5Vout Triple: 12Vout 15Vout 25% load step change GENERAL SPECIFICATIONS Parameter Case material Base material Potting material Weight MTBF Triple: 12Vout, 15Vout Single Dual Triple: 3.3Vout, 5Vout Triple: 12Vout, 15Vout Single Dual Triple: 3.3Vout, 5Vout Triple: 12Vout, 15Vout Dual Triple: 3.3Vout, 5Vout Triple: 12Vout, 15Vout Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 10 Vr.m.s Level Class A, Class B Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Note: 1. 2. 3. 4. 3 The output requires a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. Test by minimum input and constant resistive load. The standard modules meet EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. www.PDUKE.com 2015/2/26 CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE FDC20-48S05 Derating Curve FDC20-48S05 Derating Curve With Heat-sink FDC20-48S05 Efficiency vs. Input Voltage FDC20-48S05 Efficiency vs. Output Load MECHANICAL DRAWING PIN CONNECTION PIN 1 2 4 5 6 7 8 SINGLE +Vin -Vin Ctrl No pin +Vout -Vout Trim DUAL +Vin -Vin Ctrl +Vout Common -Vout Trim TRIPLE +Vin -Vin Ctrl +Aux +Vout Common -Aux EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim. TRIM UP 7(7) TRIM DOWN 8(8) RU 8(8) RD 6(5) 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2015/2/26