KAI-04070 - ON Semiconductor

KAI-04070
2048 (H) x 2048 (V) Interline
CCD Image Sensor
Description
The KAI−04070 Image Sensor is a 4-megapixel CCD in a 4/3 inch
optical format. Based on the TRUESENSE 7.4 micron Interline
Transfer CCD Platform, the sensor provides very high smear rejection
and up to 82 dB linear dynamic range through the use of a unique
dual-gain amplifier. A flexible readout architecture enables use of 1, 2,
or 4 outputs for full resolution readout up to 28 frames per second,
while a vertical overflow drain structure suppresses image blooming
and enables electronic shuttering for precise exposure control.
www.onsemi.com
Table 1. GENERAL SPECIFICATIONS
Parameter
Typical Value
Architecture
Interline CCD, Progressive Scan
Total Number of Pixels
2128 (H) × 2112 (V)
Number of Effective Pixels
2080 (H) × 2080 (V)
Number of Active Pixels
2048 (H) × 2048 (V)
Pixel Size
7.4 mm (H) × 7.4 mm (V)
Active Image Size
15.2 mm (H) × 15.2 mm (V),
21.4 mm (Diagonal),
4/3″ Optical Format
Aspect Ratio
1:1
Number of Outputs
1, 2, or 4
Charge Capacity
44,000 electrons
Output Sensitivity
8.7 mV/e− (Low), 33 mV/e− (High)
Quantum Efficiency
Pan (−ABA, −PBA, −QBA)
R, G, B (−CBA)
R, G, B (−FBA)
52%
38%, 42%, 43%
37%, 42%, 41%
Read Noise (f = 40 MHz)
12 e− rms
Dark Current
Photodiode
VCCD
3 e−/s
145 e−/s
Dark Current Doubling Temp.
Photodiode
VCCD
7°C
9°C
Dynamic Range
High Gain Amp (40 MHz)
Dual Amp, 2×2 Bin (40 MHz)
70 dB
82 dB
Charge Transfer Efficiency
0.999999
Blooming Suppression
> 1000 X
Smear
−115 dB
Image Lag
< 10 electrons
Maximum Pixel Clock Speed
40 MHz
Maximum Frame Rate
Quad Output
Dual Output
Single Output
28 fps
14 fps
8 fps
Package
68 Pin PGA
Cover Glass
AR Coated, 2 Sides
Figure 1. KAI−04070 Interline CCD
Image Sensor
Features
• Superior Smear Rejection
• Up to 82 dB Linear Dynamic Range
• Bayer Color Pattern, TRUESENSE Sparse
•
•
•
•
Color Filter Pattern, and Monochrome
Configurations
Progressive Scan & Flexible Readout
Architecture
High Frame Rate
High Sensitivity − Low Noise Architecture
Package Pin Reserved for Device
Identification
Application
• Industrial Imaging and Inspection
• Traffic
• Surveillance
ORDERING INFORMATION
See detailed ordering and shipping information on page 2 of
this data sheet.
NOTE: All Parameters are specified at T = 40°C unless otherwise noted.
© Semiconductor Components Industries, LLC, 2015
July, 2015 − Rev. 3
1
Publication Order Number:
KAI−04070/D
KAI−04070
The sensor is available with the TRUESENSE Sparse
Color Filter Pattern, a technology which provides a 2x
improvement in light sensitivity compared to a standard
color Bayer part.
The sensor shares common pin-out and electrical
configurations with a full family of Truesense Imaging
Interline Transfer CCD image sensors, allowing a single
camera design to be leveraged in support of multiple
devices.
ORDERING INFORMATION
Table 2. ORDERING INFORMATION − KAI−04070 IMAGE SENSOR
Part Number
Description
Marking Code
KAI−04070−ABA−JD−BA
Monochrome, Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade
KAI−04070−ABA−JD−AE
Monochrome, Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
KAI−04070−ABA−JR−BA
Monochrome, Telecentric Microlens, PGA Package,
Taped Clear Cover Glass with AR Coating (Both Sides), Standard Grade
KAI−04070−ABA−JR−AE
Monochrome, Telecentric Microlens, PGA Package,
Taped Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
11KAI−04070−FBA−JD−BA
Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade
11KAI−04070−FBA−JD−AE
Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
11KAI−04070−QBA−JD−BA
Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade
11KAI−04070−QBA−JD−AE
Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
11KAI−04070−CBA−JD−BA*
Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade
11KAI−04070−CBA−JD−AE*
Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
11KAI−04070−PBA−JD−BA*
Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade
11KAI−04070−PBA−JD−AE*
Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package,
Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade
KAI−04070−ABA
Serial Number
KAI−04070−FBA
Serial Number
KAI−04070−QBA
Serial Number
KAI−04070−CBA
Serial Number
KAI−04070−PBA
Serial Number
*Note recommended for new designs.
Table 3. ORDERING INFORMATION − EVALUATION SUPPORT
Part Number
Description
G2−FPGA−BD−14−40−A−GEVK
FPGA Board for IT−CCD Evaluation Hardware
KAI−68PIN−HEAD−BD−A−GEVB
68 Pin Imager Board for IT−CCD Evaluation Hardware
LENS−MOUNT−KIT−A−GEVK
Lens Mount Kit for IT−CCD Evaluation Hardware
KAI−68PIN−N−PROBE−CARD−A−GEVB
68 Pin Probe Card (Narrow Socket)
KAI−68PIN−W−PROBE−CARD−A−GEVB
68 Pin Probe Card (Wide Socket)
See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention
used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at
www.onsemi.com.
www.onsemi.com
2
KAI−04070
DEVICE DESCRIPTION
Architecture
R2cd
RDcd
H2B d
H2S d
H1B d
H1S d
SUB
H2B c
H2S c
H1B c
H1S c
RDcd
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
R1c
HLOD
VDDc
VOUTc
1 11 24 16
1024
1024
16
8 24 11 1
1 Dummy
16
16
GND
OGc
H2SLc
R2cd
R1d
VDDd
VOUTd
GND
OGd
H2 SLd
V1T
V2T
V3T
V4T
V1T
V2T
V3T
V4T
DevID
ESD
2048H x 2048V
7.4mm x 7.4mm Pixels
24 16
16 24
V1B
V2B
V3B
V4B
RDab
R2ab
R1 a
VDDa
VOUTa
ESD
V1B
V2B
V3B
V4B
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
16 Buffer
16 Dark
1 Dummy (Last VCCD Phase = V1 à H1S)
1 11 24 16
8
1024
1024
16
8 24 11 1
RDab
R2ab
R1b
VDDb
VOUTb
HLOD
H2Bb
H2Sb
H1Bb
H1Sb
SUB
H2Ba
H2Sa
H1Ba
H1Sa
GND
OGa
H2SLa
GND
OGb
H2SLb
Figure 2. Block Diagram
Dark Reference Pixels
Image Acquisition
There are 16 dark reference rows at the top and 16 dark
rows at the bottom of the image sensor. The 24 dark columns
on the left or right side of the image sensor should be used
as a dark reference.
Under normal circumstances use only the center
22 columns of the 24 column dark reference due to potential
light leakage.
An electronic representation of an image is formed when
incident photons falling on the sensor plane create
electron-hole pairs within the individual silicon
photodiodes. These photoelectrons are collected locally by
the formation of potential wells at each photosite. Below
photodiode saturation, the number of photoelectrons
collected at each pixel is linearly dependent upon light level
and exposure time and non-linearly dependent on
wavelength. When the photodiodes charge capacity is
reached, excess electrons are discharged into the substrate to
prevent blooming.
Dummy Pixels
Within each horizontal shift register there are 12 leading
additional shift phases. These pixels are designated as
dummy pixels and should not be used to determine a dark
reference level.
In addition, there is one dummy row of pixels at the top
and bottom of the image.
ESD Protection
Adherence to the power-up and power-down sequence is
critical. Failure to follow the proper power-up and
power-down sequences may cause damage to the sensor. See
Power-Up and Power-Down Sequence section.
Active Buffer Pixels
16 unshielded pixels adjacent to any leading or trailing
dark reference regions are classified as active buffer pixels.
These pixels are light sensitive but are not tested for defects
and non-uniformities.
www.onsemi.com
3
KAI−04070
Bayer Color Filter Pattern
RDcd
R2cd
R1d
VDDd
VOUTd
H2Bd
H2Sd
H1Bd
H1Sd
SUB
GND
OGc
H2SLc
H2Bc
H2Sc
H1Bc
H1Sc
RDcd
R2cd
R1c
VDDc
VOUTc
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
HLOD
1 11 24 16
1024
1024
16
8 24 11 1
1Dummy
16
16
B G
G R
V1T
V2T
V3T
V4T
B G
G R
GND
OGd
H2SLd
V1T
V2T
V3T
V4T
DevID
ESD
V1B
V2B
V3B
V4B
RDab
R2ab
R1a
VDDa
VOUTa
2048 (H) × 2048 (V)
7.4 mm × 7.4 mm Pixels
24 16
16 24
B G
G R
ESD
B G
G R
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
V1B
V2B
V3B
V4B
RDab
R2ab
R1b
VDDb
VOUTb
16 Buffer
16 Dark
1 Dummy (Last VCCD Phase = V1 → H1S)
1 11 24 16
8
1024
1024
16
8 24 11 1
HLOD
GND
OGb
H2SLb
H2Bb
H2Sb
H1Bb
H1Sb
SUB
H2Ba
H2Sa
H1Ba
H1Sa
GND
OGa
H2SLa
Figure 3. Bayer Color Filter Pattern
TRUESENSE Sparse Color Filter Pattern
RDcd
R2cd
R1d
VDDd
VOUTd
H2Bd
H2Sd
H1Bd
H1Sd
SUB
GND
OGc
H2SLc
H2Bc
H2Sc
H1Bc
H1Sc
RDcd
R2cd
R1c
VDDc
VOUTc
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
HLOD
1 11 24 16
1024
1024
16
8 24 11 1
1 Dummy
16
16
G
P
B
P
V1T
V2T
V3T
V4T
P
G
P
B
R
P
G
P
G
P
B
P
P
R
P
G
P
G
P
B
R
P
G
P
P
R
P
G
GND
OGd
H2SLd
V1T
V2T
V3T
V4T
DevID
ESD
V1B
V2B
V3B
V4B
RDab
R2ab
R1a
VDDa
VOUTa
G
P
B
P
P
G
P
B
R
P
G
P
16 24
G
P
B
P
P
R
P
G
P
G
P
B
R
P
G
P
ESD
V1B
V2B
V3B
V4B
P
R
P
G
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
16 Buffer
16 Dark
1 Dummy (Last VCCD Phase = V1 → H1S)
1 11 24 16
8
1024
1024
16
8 24 11 1
HLOD
H2Bb
H2Sb
H1Bb
H1Sb
SUB
H2Ba
H2Sa
H1Ba
H1Sa
GND
OGa
H2SLa
2048 (H) × 2048 (V)
7.4 mm × 7.4 mm Pixels
24 16
Figure 4. TRUESENSE Sparse Color Filter Pattern
www.onsemi.com
4
RDab
R2ab
R1b
VDDb
VOUTb
GND
OGb
H2SLb
KAI−04070
Physical Description
Pin Description and Device Orientation
H2Sc
R2cd
H2Sd
H1Bd
H2SLd
Rd
GND
VDDd
V1T
V3T
57
55
53
51
49
47
45
43
41
39
37
35
VOUTc RDcd
OGc
H2Bc
H1Sc
SUB
H1Sd
H2Bd
OGd
62
58
56
54
52
50
48
46
V3T
V1T
VDDc
GND
Rc
67
65
63
61
59
ESD V4T
V2T
68
64
66
60
H2SLc H1Bc
RDcd VOUTd
44
42
26
28
V2T
40
V4T DevID
38
36
32
34
Pixel (1,1)
4
V4B
6
V2B
8
10
VOUTa RDab
1
3
5
7
9
V3B
V1B
VDDa
GND
Ra
12
14
16
18
20
22
24
OGa
H2Ba
H1Sa
SUB
H1Sb
H2Bb
OGb
11
13
15
17
19
21
23
25
27
29
31
33
H2Sa
R2ab
H2Sb
H1Bb
H2SLb
Rb
GND
VDDb
V1B
V3B
H2SLa H1Ba
RDab VOUTb
30
V2B
V4B
ESD
Figure 5. Package Pin Designations − Top View
Table 4. PACKAGE PIN DESCRIPTION
Pin
Name
Description
1
V3B
Vertical CCD Clock, Phase 3, Bottom
3
V1B
Vertical CCD Clock, Phase 1, Bottom
4
V4B
Vertical CCD Clock, Phase 4, Bottom
5
VDDa
Output Amplifier Supply, Quadrant a
6
V2B
Vertical CCD Clock, Phase 2, Bottom
7
GND
Ground
8
VOUTa
9
Ra
Video Output, Quadrant a
Reset Gate, Standard (High) Gain, Quadrant a
10
RDab
Reset Drain, Quadrants a & b
11
H2SLa
Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant a
12
OGa
Output Gate, Quadrant a
13
H1Ba
Horizontal CCD Clock, Phase 1, Barrier, Quadrant a
14
H2Ba
Horizontal CCD Clock, Phase 2, Barrier, Quadrant a
15
H2Sa
Horizontal CCD Clock, Phase 2, Storage, Quadrant a
16
H1Sa
Horizontal CCD Clock, Phase 1, Storage, Quadrant a
17
R2ab
Reset Gate, Low Gain, Quadrants a & b
18
SUB
Substrate
19
H2Sb
Horizontal CCD Clock, Phase 2, Storage, Quadrant b
20
H1Sb
Horizontal CCD Clock, Phase 1, Storage, Quadrant b
21
H1Bb
Horizontal CCD Clock, Phase 1, Barrier, Quadrant b
www.onsemi.com
5
KAI−04070
Table 4. PACKAGE PIN DESCRIPTION (continued)
Pin
Name
Description
22
H2Bb
Horizontal CCD Clock, Phase 2, Barrier, Quadrant b
23
H2SLb
Horizontal CCD Clock, Phase 1, Storage, Last Phase, Quadrant b
24
OGb
25
Rb
26
RDab
Reset Drain, Quadrants a & b
27
GND
Ground
28
VOUTb
29
VDDb
Output Amplifier Supply, Quadrant b
30
V2B
Vertical CCD Clock, Phase 2, Bottom
31
V1B
Vertical CCD Clock, Phase 1, Bottom
32
V4B
Vertical CCD Clock, Phase 4, Bottom
33
V3B
Vertical CCD Clock, Phase 3, Bottom
34
ESD
ESD Protection Disable
35
V3T
Vertical CCD Clock, Phase 3, Top
36
DevID
37
V1T
Vertical CCD Clock, Phase 1, Top
38
V4T
Vertical CCD Clock, Phase 4, Top
39
VDDd
Output Gate, Quadrant b
Reset Gate, Standard (High) Gain, Quadrant b
Video Output, Quadrant b
Device Identification
Output Amplifier Supply, Quadrant d
40
V2T
Vertical CCD Clock, Phase 2, Top
41
GND
Ground
42
VOUTd
Video Output, Quadrant d
43
Rd
44
RDcd
Reset Gate, Standard (High) Gain, Quadrant d
Reset Drain, Quadrants c & d
45
H2SLd
Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant d
46
OGd
Output Gate, Quadrant d
47
H1Bd
Horizontal CCD Clock, Phase 1, Barrier, Quadrant d
48
H2Bd
Horizontal CCD Clock, Phase 2, Barrier, Quadrant d
49
H2Sd
Horizontal CCD Clock, Phase 2, Storage, Quadrant d
50
H1Sd
Horizontal CCD Clock, Phase 1, Storage, Quadrant d
51
R2cd
Reset Gate, Low Gain, Quadrants c & d
52
SUB
Substrate
53
H2Sc
Horizontal CCD Clock, Phase 2, Storage, Quadrant c
54
H1Sc
Horizontal CCD Clock, Phase 1, Storage, Quadrant c
55
H1Bc
Horizontal CCD Clock, Phase 1, Barrier, Quadrant c
56
H2Bc
Horizontal CCD Clock, Phase 2, Barrier, Quadrant c
57
H2SLc
Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant c
58
OGc
59
Rc
60
RDcd
Reset Drain, Quadrants c & d
61
GND
Ground
62
VOUTc
Video Output, Quadrant c
63
VDDc
Output Amplifier Supply, Quadrant c
64
V2T
Vertical CCD Clock, Phase 2, Top
65
V1T
Vertical CCD Clock, Phase 1, Top
66
V4T
Vertical CCD Clock, Phase 4, Top
67
V3T
Vertical CCD Clock, Phase 3, Top
68
ESD
EDS Protection Disable
Output Gate, Quadrant c
Reset Gate, Standard (High) Gain, Quadrant c
1. Liked named pins are internally connected and should have a common drive signal.
www.onsemi.com
6
KAI−04070
IMAGING PERFORMANCE
Table 5. TYPICAL OPERATIONAL CONDITIONS
(Unless otherwise noted, the Imaging Performance Specifications are measured using the following conditions.)
Condition
Description
Light Source
Continuous Red, Green and Blue LED Illumination
Operation
Nominal Operating Voltages and Timing
Notes
1
1. For monochrome sensor, only green LED used.
Specifications
Table 6. PERFORMANCE SPECIFICATIONS
Temperature
Tested at
(5C)
Symbol
Min.
Nom.
Max.
Unit
Sampling
Plan
DSNU
−
−
2.0
mVpp
Die
27, 40
−
2.0
5.0
% rms
Die
27, 40
−
5.0
15.0
% pp
Die
27, 40
−
1.0
2.0
% rms
Die
27, 40
%
Design
NL_HG1
NL_HG2
NL_LG1
−
−
−
2
3
6
−
−
−
Maximum Gain Difference between
Outputs (Note 2)
DG
−
−
10
%
Design
Horizontal CCD Charge Capacity
HNe
−
90
−
ke−
Design
Vertical CCD Charge Capacity
VNe
−
60
−
ke−
Design
Description
ALL CONFIGURATIONS
Dark Field Global Non-Uniformity
Bright Field Global Non-Uniformity
(Note 1)
Bright Field Global Peak to Peak
Non-Uniformity (Note 1)
PRNU
Bright Field Center Non-Uniformity
(Note 1)
Maximum Photoresponse Non-Linearity
High Gain (4,000 to 20,000 electrons)
High Gain (4,000 to 40,000 electrons)
Low Gain (8,000 to 80,000 electrons)
Photodiode Charge Capacity (Note 3)
Floating Diffusion Capacity − High Gain
Floating Diffusion Capacity − Low Gain
PNe
−
44
−
ke−
Die
27, 40
FNe_HG
40
−
−
ke−
Die
27, 40
ke−
Die
27, 40
FNe_LG
160
−
−
Horizontal CCD Charge Transfer
Efficiency
HCTE
0.999995
0.999999
−
Die
Vertical CCD Charge Transfer
Efficiency
VCTE
0.999995
0.999999
−
Die
Photodiode Dark Current
IPD
−
7
70
e/p/s
Die
40
Vertical CCD Dark Current
IVD
−
140
400
e/p/s
Die
40
Image Lag
Lag
−
−
10
e−
Design
Anti-Blooming Factor
XAB
1,000
−
−
Vertical Smear
Smr
−
−115
−
dB
Design
Read Noise (Note 4)
High Gain
Low Gain
ne−T
−
−
e− rms
Design
Dynamic Range, Standard (Notes 4, 5)
DR
−
70.5
−
dB
Design
Dynamic Range, Extended Linear
Dynamic Range Mode (XLDR)
(Notes 4, 5)
XLDR
−
82.5
−
dB
Design
Output Amplifier DC Offset
VODC
−
9.0
−
V
Die
Output Amplifier Bandwidth (Note 6)
f−3db
−
250
−
MHz
Die
Output Amplifier Impedance
ROUT
−
127
−
W
Die
mV/e−
Design
Output Amplifier Sensitivity
High Gain
Low Gain
Design
12
45
DV/DN
−
−
33
8.7
www.onsemi.com
7
−
−
27, 40
27, 40
KAI−04070
Table 6. PERFORMANCE SPECIFICATIONS (continued)
Description
Symbol
Min.
Nom.
Max.
Unit
Sampling
Plan
Temperature
Tested at
(5C)
KAI−04070−ABA AND KAI−04070−PBA AND KAI−04070−QBA CONFIGURATIONS
Peak Quantum Efficiency
Peak Quantum Efficiency Wavelength
QEMAX
−
52
−
%
Design
lQE
−
500
−
nm
Design
%
Design
nm
Design
%
Design
nm
Design
KAI−04070−FBA AND KAI−04070−QBA GEN2 COLOR CONFIGURATIONS
QEMAX
Peak Quantum Efficiency
Blue
Green
Red
Peak Quantum Efficiency Wavelength
Blue
Green
Red
−
−
−
41
42
37
−
−
−
−
−
−
460
535
610
−
−
−
lQE
KAI−04070−CBA AND KAI−04070−PBA GEN1 COLOR CONFIGURATIONS (Note 7)
Peak Quantum Efficiency
Blue
Green
Red
QEMAX
Peak Quantum Efficiency Wavelength
Blue
Green
Red
−
−
−
43
42
38
−
−
−
−
−
−
470
540
620
−
−
−
lQE
1. Per color.
2. Value is over the range of 10% to 90% of linear signal level saturation.
3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such
that the photodiode charge capacity is 440 mV. This value is determined while operating the device in the low gain mode. VAB value assigned
is valid for both modes; high gain or low gain.
4. At 40 MHz.
5. Uses 20LOG (PNe / ne−T).
6. Assumes 5 pF load.
7. This color filter set configuration (Gen1) is not recommended for new designs.
Low Gain
Output of Sensor Not Verified
Output of Sensor Not Verified
160,000
1,600
30,000
990
120,000
1,200
4,000
80,000
330
40,000
132
8,000
0
0
0
800
NL_LG1 Linearity Range
10,000
660
Output Signal (mV)
20,000
Output Signal (electrons)
1,320
NL_HG2 Linearity Range
40,000
80
0
Light or Exposure (arbitrary)
0
0
Figure 6. High Gain Linear Signal Range
Light or Exposure (arbitrary)
Figure 7. Low Gain Linear Signal Range
www.onsemi.com
8
400
Output Signal (mV)
High Gain
NL_HG1 Linearity Range
Output Signal (electrons)
Linear Signal Range
KAI−04070
TYPICAL PERFORMANCE CURVES
Quantum Efficiency
Monochrome with Microlens
Figure 8. Monochrome with Microlens Quantum Efficiency
Color (Bayer RGB) with Microlens(Gen2 and Gen1 CFA)
Figure 9. Color (Bayer RGB) with Microlens Quantum Efficiency
www.onsemi.com
9
KAI−04070
Color (TRUESENSE Sparse CFA) with Microlens (Gen2 and Gen1 CFA)
Figure 10. Color (TRUESENSE Sparse CFA) with Microlens Quantum Efficiency
Angular Quantum Efficiency
For the curves marked “Horizontal”, the incident light angle is varied in a plane parallel to the HCCD.
For the curves marked “Vertical”, the incident light angle is varied in a plane parallel to the VCCD.
Monochrome with Microlens
100
Relative Quantum Efficiency (%)
90
Vertical
80
70
60
50
Horizontal
40
30
20
10
0
−40
−30
−20
−10
0
10
20
30
40
Angle (degrees)
Figure 11. Monochrome with Microlens Angular Quantum Efficiency
www.onsemi.com
10
KAI−04070
Color (Bayer RGB) with Microlens
100
90
Relative Quantum Efficiency (%)
Vertical
80
70
60
50
Horizontal
40
30
20
10
0
−40
−30
−20
−10
0
10
20
30
40
Angle (degrees)
Figure 12. Color (Bayer RGB) with Microlens Angular Quantum Efficiency
Dark Current vs. Temperature
1,000.00
Photodiode
VCCD
Dark Current (e/s)
100.00
10.00
70°C
60°C
1.00
50°C
40°C
30°C
0.10
20°C
10°C
0.01
2.90
3.00
3.10
3.20
3.30
3.40
1000/T (K)
Figure 13. Dark Current vs. Temperature
www.onsemi.com
11
3.50
3.60
KAI−04070
Power-Estimated
Power-Estimated − Full Resolution
1.2
1.2
Single
Dual (VOUTa/VOUTb)
1.0
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0.0
Power (W)
Power (W)
Quad
0.0
0
5
10
15
20
25
30
35
40
HCCD Frequency (MHz)
Figure 14. Power − Full Resolution
Power-Estimated − 1/4 Resolution − 2y2 Binning
1.2
1.2
Single
Dual (VOUTa/VOUTb)
1.0
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0.0
0.0
0
5
10
15
20
25
30
35
HCCD Frequency (MHz)
Figure 15. Power − 1/4 Resolution − Constant HCCD
www.onsemi.com
12
40
Power (W)
Power (W)
Quad
KAI−04070
Power-Estimated − 1/4 Resolution − 2y2 Binning using Variable HCCD XLDR
1.2
1.2
Single
Dual (VOUTa/VOUTb)
1.0
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0.0
Power (W)
Power (W)
Quad
0.0
0
5
10
15
20
25
30
35
40
HCCD Frequency (MHz)
Figure 16. Power − 1/4 Resolution − Variable HCCD XLDR
Power-Estimated − 1/4 Resolution − 2y2 Binning using Constant HCCD XLDR
1.2
1.2
Single
Dual (VOUTa/VOUTb)
1.0
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0.0
0.0
0
5
10
15
20
25
30
35
HCCD Frequency (MHz)
Figure 17. Power − 1/4 Resolution − Constant HCCD XLDR
www.onsemi.com
13
40
Power (W)
Power (W)
Quad
KAI−04070
Frame Rates
Frame Rates − Full Resolution
Frame rates are for low and high gain modes of operation.
30
30
Single
Dual (VOUTa/VOUTc)
25
25
Dual (VOUTa/VOUTb)
20
15
15
10
10
5
5
0
Frame Rate (fps)
Frame Rate (fps)
Quad
20
0
0
5
10
15
20
25
30
35
40
HCCD Frequency (MHz)
Figure 18. Frame Rates − Full Resolution
Frame Rates − 1/4 Resolution − 2y2 Binning
Frame rates are for low and high gain modes of operation.
50
50
Single
45
45
Dual (VOUTa/VOUTc)
Quad
35
Frame Rate (fps)
40
Dual (VOUTa/VOUTb)
35
30
30
25
25
20
20
15
15
10
10
5
5
0
0
0
5
10
15
20
25
30
35
HCCD Frequency (MHz)
Figure 19. Frame Rates − 1/4 Resolution − Constant HCCD
www.onsemi.com
14
40
Frame Rate (fps)
40
KAI−04070
Frame Rates − 1/4 Resolution − 2y2 Binning using Variable HCCD XLDR
Frame rates for variable HCCD modes of operation.
40
40
Single
35
35
Dual (VOUTa/VOUTc)
Dual (VOUTa/VOUTb)
30
30
25
25
20
20
15
15
10
10
5
5
0
Frame Rate (fps)
Frame Rate (fps)
Quad
0
0
5
10
15
20
25
30
35
40
HCCD Frequency (MHz)
Figure 20. Frame Rates − 1/4 Resolution − Variable HCCD XLDR
Frame Rates − 1/4 Resolution − 2y2 Binning using Constant HCCD XLDR
Frame rates for a constant HCCD mode of operation.
40
40
Single
35
35
Dual (VOUTa/VOUTc)
Dual (VOUTa/VOUTb)
30
30
25
25
20
20
15
15
10
10
5
5
0
0
0
5
10
15
20
25
30
35
40
HCCD Frequency (MHz)
Figure 21. Frame Rates − 1/4 Resolution − Constant HCCD XLDR
www.onsemi.com
15
Frame Rate (fps)
Frame Rate (fps)
Quad
KAI−04070
DEFECT DEFINITIONS
Table 7. OPERATION CONDITIONS FOR DEFECT TESTING AT 405C
Description
Condition
Operational Mode
One Output, using VOUTa, Continuous Readout
HCCD Clock Frequency
20 MHz
Pixels per Line
2,140
Lines per Frame
2,112
Line Time
115.0 ms
Frame Time
242.9 ms
Photodiode Integration Time (PD_Tint)
Notes
PD_Tint = Frame Time = 242.9 ms, No Electronic Shutter Used
Temperature
40°C
Light Source
Continuous Red, Green and Blue LED Illumination
Operation
1
Nominal Operating Voltages and Timing
1. For monochrome sensor, only the green LED is used.
Table 8. DEFECT DEFINITIONS FOR TESTING AT 405C
Description
Definition
Standard Grade
Notes
Defect ≥ 83 mV
40
1
−12% ≥ Defect ≥ 12%
40
1
Defect ≥ 41 mV
400
Cluster Defect
A group of 2 to 10 contiguous major defective pixels,
but no more than 2 adjacent defect horizontally.
8
2
Column Defect
A group of more than 10 contiguous major defective
pixels along a single column.
0
2
Major Dark Field Defective Bright Pixel
Major Bright Field Defective Pixel
Minor Dark Field Defective Bright Pixel
1. For the color devices (KAI−04070−CBA and KAI−04070−PBA), a bright field defective pixel deviates by 12% with respect to pixels of the
same color.
2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects).
www.onsemi.com
16
KAI−04070
Table 9. OPERATION CONDITIONS FOR DEFECT TESTING AT 275C
Description
Condition
Operational Mode
Notes
One Output, Using VOUTa, Continuous Readout
HCCD Clock Frequency
20 MHz
Pixels per Line
2,140
Lines per Frame
2,112
Line Time
115 ms
Frame Time
242.9 ms
Photodiode Integration Time (PD_Tint)
PD_Tint = Frame Time = 242.9 ms, No Electronic Shutter Used
Temperature
27°C
Light Source
Continuous Red, Green and Blue LED Illumination
Operation
1
Nominal Operating Voltages and Timing
1. For monochrome sensor, only the green LED is used.
Table 10. DEFECT DEFINITIONS FOR TESTING AT 405C
Description
Definition
Standard Grade
Notes
Defect ≥ 27 mV
40
1
−12% ≥ Defect ≥ 12%
40
1
Cluster Defect
A group of 2 to 10 contiguous major defective pixels,
but no more than 2 adjacent defect horizontally.
8
2
Column Defect
A group of more than 10 contiguous major defective
pixels along a single column.
0
2
Major Dark Field Defective Bright Pixel
Major Bright Field Defective Pixel
1. For the color devices (KAI−04070−CBA and KAI−04070−PBA), a bright field defective pixel deviates by 12% with respect to pixels of the
same color.
2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects).
Defect Map
defects are not included in the defect map. All defective
pixels are reference to pixel 1, 1 in the defect maps. See
Figure 22 for the location of pixel 1, 1.
The defect map supplied with each sensor is based upon
testing at an ambient (27°C) temperature. Minor point
www.onsemi.com
17
KAI−04070
TEST DEFINITIONS
Test Regions of Interest
Overclocking
Image Area ROI:
Active Area ROI:
Center ROI:
The test system timing is configured such that the sensor
is overclocked in both the vertical and horizontal directions.
See Figure 22 for a pictorial representation of the regions of
interest.
Pixel (1, 1) to Pixel (2080, 2080)
Pixel (17, 17) to Pixel (2064, 2064)
Pixel (991, 991) to Pixel (1090, 1090)
Only the Active Area ROI pixels are used for performance
and defect tests.
16 Dark Rows
24 Dark Columns
2048 × 2048
Active Pixels
16 Buffer Columns
16 Buffer Columns
24 Dark Columns
16 Buffer Rows
Pixel
17,
17
Pixel
1, 1
16 Buffer Rows
16 Dark Rows
VOUTa
Figure 22. Regions of Interest
Tests
Dark Field Global Non-Uniformity
This test is performed under dark field conditions.
The sensor is partitioned into 256 sub regions of interest,
each of which is 128 by 128 pixels in size. The average signal
level of each of the 256 sub regions of interest is calculated.
The signal level of each of the sub regions of interest is
calculated using the following formula:
are found. The dark field global uniformity is then calculated
as the maximum signal found minus the minimum signal
level found.
Global Non-Uniformity
This test is performed with the imager illuminated to
a level such that the output is at 70% of saturation
(approximately 924 mV). Prior to this test being performed
the substrate voltage has been set such that the charge
capacity of the sensor is 1,320 mV. Global non-uniformity
is defined as
Signal of ROI[i] + (ROI Average in Counts *
* Horizontal Overclock Average in Counts) @
@ mV per Count
Global Non−Uniformity + 100 @
Units : mVpp (millivolts Peak to Peak)
where i = 1 to 256. During this calculation on the 256 sub
regions of interest, the maximum and minimum signal levels
ǒ
Active Area Standard Deviation
Active Area Signal
Ǔ
Units : % rms
Active Area Signal = Active Area Average − Dark Column Average
www.onsemi.com
18
KAI−04070
Bright Field Defect Test
This test is performed with the imager illuminated to
a level such that the output is at approximately 924 mV.
Prior to this test being performed the substrate voltage has
been set such that the charge capacity of the sensor is
1,320 mV. The average signal level of all active pixels is
found. The bright and dark thresholds are set as:
Global Peak to Peak Non-Uniformity
This test is performed with the imager illuminated to
a level such that the output is at 70% of saturation
(approximately 924 mV). Prior to this test being performed
the substrate voltage has been set such that the charge
capacity of the sensor is 1,320 mV. The sensor is partitioned
into 256 sub regions of interest, each of which is 128 by 128
pixels in size. The average signal level of each of the 256 sub
regions of interest (ROI) is calculated. The signal level of
each of the sub regions of interest is calculated using the
following formula:
Dark Defect Threshold = Active Area Signal @ Threshold
Bright Defect Threshold = Active Area Signal @ Threshold
The sensor is then partitioned into 256 sub regions of
interest, each of which is 128 by 128 pixels in size. In each
region of interest, the average value of all pixels is found.
For each region of interest, a pixel is marked defective if it
is greater than or equal to the median value of that region of
interest plus the bright threshold specified or if it is less than
or equal to the median value of that region of interest minus
the dark threshold specified.
• Example for major bright field defective pixels:
• Average value of all active pixels is found to be 924 mV
• Dark defect threshold: 924 mV ⋅ 12% = 111 mV
• Bright defect threshold: 924 mV ⋅ 12% = 111 mV
• Region of interest #1 selected. This region of interest is
pixels 17, 17 to pixels 144, 144
♦ Median of this region of interest is found to be
920 mV
♦ Any pixel in this region of interest that is
≤ (920 − 111 mV) 809 mV in intensity will be
marked defective
♦ Any pixel in this region of interest that is
≥ (920 + 111 mV) 1,031 mV in intensity will be
marked defective
• All remaining 144 sub regions of interest are analyzed
for defective pixels in the same manner
Signal of ROI[i] + (ROI Average in Counts *
* Horizontal Overclock Average in Counts) @
@ mV per Count
Where i = 1 to 256. During this calculation on the 144 sub
regions of interest, the maximum and minimum signal levels
are found. The global peak to peak uniformity is then
calculated as:
Global Uniformity + 100 @
ǒ
Ǔ
Max. Signal * Min. Signal
Active Area Signal
Units : % pp
Center Non-Uniformity
This test is performed with the imager illuminated to
a level such that the output is at 70% of saturation
(approximately 924 mV). Prior to this test being performed
the substrate voltage has been set such that the charge
capacity of the sensor is 1,320 mV. Defects are excluded for
the calculation of this test. This test is performed on the
center 100 by 100 pixels of the sensor. Center uniformity is
defined as:
Center ROI Uniformity + 100 @
ǒ
Center ROI Standard Deviation
Center ROI Signal
Ǔ
Units : % rms
Center ROI Signal = Center ROI Average − Dark Colum Average
Dark Field Defect Test
This test is performed under dark field conditions.
The sensor is partitioned into 256 sub regions of interest,
each of which is 128 by 128 pixels in size. In each region of
interest, the median value of all pixels is found. For each
region of interest, a pixel is marked defective if it is greater
than or equal to the median value of that region of interest
plus the defect threshold specified in the “Detect
Definitions” section.
www.onsemi.com
19
KAI−04070
OPERATION
Absolute Maximum Ratings
description. If the level or the condition is exceeded,
the device will be degraded and may be damaged. Operation
at these values will reduce MTTF.
Absolute maximum rating is defined as a level or
condition that should not be exceeded at any time per the
Table 11. ABSOLUTE MAXIMUM RATINGS
Description
Symbol
Minimum
Maximum
Unit
Notes
Operating Temperature
TOP
−50
70
°C
1
Humidity
RH
5
90
%
2
Output Bias Current
IOUT
−
60
mA
3
CL
−
10
pF
Off-Chip Load
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Noise performance will degrade at higher temperatures.
2. T = 25°C. Excessive humidity will degrade MTTF.
3. Total for all outputs. Maximum current is −15 mA for each output. Avoid shorting output pins to ground or any low impedance source during
operation. Amplifier bandwidth increases at higher current and lower load capacitance at the expense of reduced gain (sensitivity).
Table 12. ABSOLUTE MAXIMUM VOLTAGE RATINGS BETWEEN PINS AND GROUND
Description
Minimum
Maximum
Unit
Notes
VDDa, VOUTa
−0.4
17.5
V
1
RDa
−0.4
15.5
V
1
V1B, V1T
ESD − 0.4
ESD + 24.0
V
V2B, V2T, V3B, V3T, V4B, V4T
ESD − 0.4
ESD + 14.0
V
H1Sa, H1Ba, H2Sa, H2Ba, H2SLa, R1a, R2a, OGa
ESD − 0.4
ESD + 14.0
V
ESD
−10.0
0.0
V
SUB
−0.4
40.0
V
1
2
1. a denotes a, b, c or d.
2. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions
• The KAI−04070 will operate in only the high gain
KAI−08050 Compatibility
The KAI−04070 is pin-for-pin compatible with a camera
designed for the KAI−08050 image sensor with the
following accommodations:
• To operate in accordance with a system designed for
KAI−08050, the target substrate voltage should be set
to be 2.0V higher than the value recorded on the
KAI−04070 shipping container. This setting will cause
the charge capacity to be limited to 20 ke− (or 660 mV)
• On the KAI−04070, pins 17 (R2ab) and 51 (R2cd)
should be left floating per the KAI−08050 Device
Performance Specification
•
•
mode (33 mV/e−)
All timing and voltages are taken from the KAI−08050
specification sheet
The number of horizontal and vertical CCD clock
cycles is reduced as appropriate
In addition, if the intent is to operate the KAI−04070
image sensor in a camera designed for the KAI−08050
sensor that has been modified to accept and process the full
40,000 e− (1,320 mV) output, the following changes to the
RD bias must be made:
Table 13.
Pins
Names
KAI−08050
KAI−04070
10, 26, 44, 60
RDa, RDb, RDc, RDd
12.0 V per the Specification
Increase to 12.6 V
To make use of the low or dual gains modes the
KAI−04070 voltages and timing specifications must be
used.
www.onsemi.com
20
KAI−04070
Reset Pin, Low Gain (R2ab and R2cd)
The R2ab and R2bc (pins 17 and 51) each have an internal
circuit to bias the pins to 4.3 V. This feature assures the
device is set to operate in the high gain mode when pins 17
VDD
(+15 V)
and 51 are not connected in the application to a clock driver
(for KAI−08050 compatibility). Typical capacitor coupled
drivers will not drive this structure.
VDD
(+15 V)
R2
4.3 V
68 kW
68 kW
20 kW
20 kW
27 kW
27 kW
GND
GND
Figure 23. Equivalent Circuit for Reset Gate, Low Gain (R2ab and R2cd)
Power-Up and Power-Down Sequence
Adherence to the power-up and power-down sequence is
critical. Failure to follow the proper power-up and
power-down sequences may cause damage to the sensor.
Do Not Pulse the Electronic Shutter until ESD is Stable
V+
VDD
SUB
Time
ESD
V−
VCCD
Low
HCCD
Low
Activate All Other Biases when ESD is Stable and Sub is above 3 V
Notes:
1. Activate all other biases when ESD is stable and SUB is above 3 V.
2. Do not pulse the electronic shutter until ESD is stable.
3. VDD cannot be +15 V when SUB is 0 V.
4. The image sensor can be protected from an accidental improper ESD voltage by current limiting the SUB current to less than 10 mA. SUB
and VDD must always be greater than GND. ESD must always be less than GND. Placing diodes between SUB, VDD, ESD and ground
will protect the sensor from accidental overshoots of SUB, VDD and ESD during power on and power off. See the figure below.
Figure 24. Power-Up and Power-Down Sequence
www.onsemi.com
21
KAI−04070
The VCCD clock waveform must not have a negative overshoot more than 0.4 V below the ESD voltage.
0.0 V
ESD
ESD − 0.4 V
All VCCD Clock Absolute
Maximum Overshoot of 0.4 V
Figure 25. VCCD Clock Waveform
Example of external diode protection for SUB, VDD and ESD. a denotes a, b, c or d.
VDDa
SUB
GND
ESD
Figure 26. Example of External Diode Protection
www.onsemi.com
22
KAI−04070
DC Bias Operating Conditions
Table 14. DC BIAS OPERATING CONDITIONS
Pins
Symbol
Min.
Nom.
Max.
Unit
Max. DC
Current
Notes
Reset Drain
RDa
RD
12.4
12.6
12.8
V
10 mA
1, 9
Output Gate
OGa
OG
−2.2
−2.0
−1.8
V
10 mA
1
Output Amplifier Supply
VDDa
VDD
14.5
15.0
15.5
V
11.0 mA
1, 2
Ground
GND
GND
0.0
0.0
0.0
V
−1.0 mA
Substrate
SUB
VSUB
5.0
VAB
VDD
V
50 mA
3, 8
ESD Protection Disable
ESD
ESD
−9.2
−9.0
Vx_L
V
50 mA
6, 7, 10
VOUTa
IOUT
−3.0
−5.0
−10.0
mA
−
1, 4, 5
Description
Output Bias Current
VDDa
RDa
Ra
R2a
1. a denotes a, b, c or d.
2. The maximum DC current is for one output. IDD = IOUT + ISS. See Figure 27.
3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such
that the photodiode charge capacity is the nominal PNe (see Specifications).
4. An output load sink must be applied to each VOUT pin to activate each output amplifier.
5. Nominal value required for 40 MHz operation per output. May be reduced for slower data rates and lower noise.
6. Adherence to the power-up and power-down sequence is critical. See Sequence section.
7. ESD maximum value must be less than or equal to V1_L + 0.4 V and V2_L + 0.4 V.
8. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions.
9. 12.0 V may be used if the total output signal desired is 20,000 e− or less.
10. Where Vx_L is the level set for V1_L, V2_L, V3_L, or V4_L in the application.
IDD
HCCD
Floating
Diffusion
IOUT
VOUTa
OGa
ISS
Source
Follower
#1
Figure 27. Output Amplifier
www.onsemi.com
23
Source
Follower
#2
Source
Follower
#3
KAI−04070
AC Operating Conditions
Table 15. CLOCK LEVELS
Description
Vertical CCD Clock, Phase 1
Vertical CCD Clock, Phase 2
Pins
(Note 1)
Symbol
Level
Min.
Nom.
Max.
Unit
V1B, V1T
V1_L
Low
−8.2
−8.0
−7.8
V
V1_M
Mid
−0.2
0.0
0.2
V1_H
High
11.5
12.0
12.5
V2B, V2T
V2_L
Low
−8.2
−8.0
−7.8
V2_H
High
−0.2
0.0
0.2
V3_L
Low
−8.2
−8.0
−7.8
Vertical CCD Clock, Phase 3
V3B, V3T
V3_H
High
−0.2
0.0
0.2
Vertical CCD Clock, Phase 4
V4B, V4T
V4_L
Low
−8.2
−8.0
−7.8
V4_H
High
−0.2
0.0
0.2
H1Sa
H1S_L
Low
−5.2
−4.0
−3.8
H1S_A
Amplitude (Note 3)
3.8
4.0
5.2
H1B_L
Low
−5.2
−4.0
−3.8
H1B_A
Amplitude (Note 3)
3.8
4.0
5.2
Horizontal CCD Clock, Phase 1 Storage
Horizontal CCD Clock, Phase 1 Barrier
Horizontal CCD Clock, Phase 2 Storage
H1Ba
H2Sa
H2S_L
Low
−5.2
−4.0
−3.8
H2S_A
Amplitude (Note 3)
3.8
4.0
5.2
−5.2
−4.0
−3.8
Horizontal CCD Clock, Phase 2 Barrier
H2Ba
H2B_L
Low
H2B_A
Amplitude (Note 3)
3.8
4.0
5.2
Horizontal CCD Clock, Last Phase
(Note 2)
H2SLa
H2SL_L
Low
−5.2
−5.0
−4.8
H2SL_A
Amplitude (Note 3)
4.8
5.0
5.2
R_L
Low
−3.2
−3.0
−2.8
R_A
Amplitude
6.0
−
6.4
Reset Gate
R1a
Reset Gate 2
R2a
Electronic Shutter (Note 4)
SUB
R2_L
Low
−2.0
−1.8
−1.6
R2_A
Amplitude
6.0
−
6.4
VES
High
29.0
30.0
40.0
V
V
V
V
V
V
V
V
V
V
V
1. a denotes a, b, c or d.
2. Use separate clock driver for improved speed performance.
3. The horizontal clock amplitude should be set such that the high level reaches 0.0 V. Examples:
a. If the minimum horizontal low voltage of −5.2 V is used, then a 5.2 V amplitude clock is required for a clock swing of −5.2 V to 0.0 V.
b. If the maximum horizontal low voltage of −3.8 V is used, then a 3.8 V amplitude clock is required for a clock swing of −3.8 V to 0.0 V.
4. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions.
The figure below shows the DC bias (VSUB) and AC clock (VES) applied to the SUB pin. Both the DC bias and AC clock
are referenced to ground.
VES
VSUB
GND
GND
Figure 28. DC Bias and AC Clock Applied to the SUB Pin
www.onsemi.com
24
KAI−04070
Capacitance
Table 16. CAPACITANCE
V1B
V2B
V3B
V4B
V1T
V2T
V3T
V4T
GND
All Pins
Unit
V1B
X
4
3
3
2
2
2
1
10
25
nF
V2B
X
X
1
3
1
1
1
1
10
20
nF
V3B
X
X
X
5
2
1
2
1
6
23
nF
V4B
X
X
X
X
2
1
1
1
13
23
nF
V1T
X
X
X
X
X
2
3
2
20
29
nF
V2T
X
X
X
X
X
X
5
3
4
21
nF
V3T
X
X
X
X
X
X
X
2
9
24
nF
V4T
X
X
X
X
X
X
X
X
3
20
nF
VSUB
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
2.8
2.8
nF
H2S
H1B
H2B
GND
All Pins
Unit
H1S
32
29
29
120
210
pF
H2S
X
16
21
170
240
pF
H1B
X
X
7
155
210
pF
H2B
X
X
X
165
235
pF
1. Tables show typical cross capacitance between pins of the device.
2. Capacitance is total for all like pins.
3. Capacitance values are estimated.
Device Identification
The device identification pin (DevID) may be used to determine which Truesense Imaging 7.4 micron pixel interline CCD
sensor is being used.
Table 17. DEVICE IDENTIFICATION
Description
Device Identification
Pins
Symbol
Min.
Nom.
Max.
Unit
Max. DC
Current
Notes
DevID
DevID
64,000
74,000
84,000
W
50 mA
1, 2, 3
1. Nominal value subject to verification and/or change during release of preliminary specifications.
2. If the Device Identification is not used, it may be left disconnected.
3. After Device Identification resistance has been read during camera initialization, it is recommended that the circuit be disabled to prevent
localized heating of the sensor due to current flow through the R_DeviceID resistor.
Recommended Circuit
Note that V1 must be a different value than V2.
V1
V2
R_external
DevID
ADC
R_DeviceID
GND
KAI−04070
Figure 29. Device Identification Recommended Circuit
www.onsemi.com
25
KAI−04070
TIMING
Requirements and Characteristics
Table 18. REQUIREMENTS AND CHARACTERISTICS
Description
Symbol
Min.
Nom.
Max.
Unit
Photodiode Transfer
tPD
1.0
−
−
ms
VCCD Leading Pedestal
t3P
4.0
−
−
ms
VCCD Trailing Pedestal
t3D
4.0
−
−
ms
VCCD Transfer
tV
2.0
−
−
ms
VVCR
75
−
100
%
1
tVR, tVF
5
−
10
%
1, 2
VCCD Clock Cross-Over
VCCD Rise, Fall Times
Notes
tHS
2.0
−
−
ms
HCCD Transfer
te
25.0
−
−
ns
Shutter Transfer
tSUB
2.0
−
−
ms
Shutter Delay
tHD
2.0
−
−
ms
Reset Pulse
tR
2.5
−
−
ns
Reset − Video Delay
tRV
−
2.2
−
ns
tHV
−
3.1
−
ns
tLINE
34.9
−
−
ms
Dual HCCD Readout
61.5
−
−
ms
Single HCCD Readout
36.9
−
−
ms
Quad HCCD Readout
73.8
−
−
ms
Dual HCCD Readout
129.9
−
−
ms
Single HCCD Readout
69.8
−
−
ms
Dual HCCD Readout
123.0
−
−
ms
Single HCCD Readout
36.9
−
−
ms
Quad HCCD Readout
73.7
−
−
ms
Dual HCCD Readout
129.9
−
−
ms
Single HCCD Readout
29.8
−
−
ms
Quad HCCD Readout
59.5
−
−
ms
Dual HCCD Readout
101.7
−
−
ms
Single HCCD Readout
HCCD Delay
H2SL − Video Delay
Line Time
Frame Time
Line Time (XLDR Bin 2×2)
tFRAME
tLINE
Frame Time (XLDR Bin 2×2)
Constant HCCD Timing
tFRAME
Frame Time (XLDR Bin 2×2)
Variable HCCD Timing
tFRAME
1. Refer to Figure 47: VCCD Clock Rise Time, Fall Time, and Edge Alignment.
2. Relative to the VCCD Transfer pulse width, tV.
www.onsemi.com
26
KAI−04070
Timing Flow Charts
In the timing flow charts the number of HCCD clock cycles per row, NH, and the number of VCCD clock cycles per frame,
NV, are shown in the following table.
Table 19. VALUES FOR NH AND NV WHEN OPERATING THE SENSOR IN THE VARIOUS MODES OF RESOLUTION
Full Resolution
1/4 Resolution
NV
NH
NV
Quad
1056
1076
Dual VOUTa, VOUTc
1056
2152
Dual VOUTa, VOUTb
2112
Single VOUTa
2112
1.
2.
3.
4.
5.
XLDR
NH
NV
NH
528
538
528
538
528
1076
528
1076
1076
1056
538
1056
538
2152
1056
1076
1056
1076
The time to read out one line tLINE = Line Timing + NH / (Pixel Frequency).
The time to read out one frame tFRAME = NV ⋅ tLINE + Frame Timing.
Line Timing: See Table 21: Line Timing.
Frame Timing: See Table 20: Frame Timing.
XLDR: eXtended Linear Dynamic Range.
No Electronic Shutter
In this case the photodiode exposure time is equal to the time to read out an image. This flow chart applies to both full and
1/4 resolution modes.
Frame Timing
(see Table 20)
Line Timing
(see Table 21)
Pixel Timing
(see Table 22)
Repeat NH
Times
Repeat NV
Times
Figure 30. Timing Flow when Electronic Shutter is Not Used
www.onsemi.com
27
KAI−04070
Using the Electronic Shutter
This flow chart applies to both the full and 1/4 resolution
modes. The exposure time begins on the falling edge of the
electronic shutter pulse on the SUB pin. The exposure time
ends on the falling edge of the photodiode transfer (tPD) of
the V1T and V1B pins. The electronic shutter timing is
shown in Figure 38.
Frame Timing
(see Table 20)
Line Timing
(see Table 21)
Pixel Timing
(see Table 22)
Repeat NH
Times
Repeat NV−NEXP
Times
Electronic
Shutter Timing
Line Timing
(see Table 21)
Pixel Timing
(see Table 22)
Repeat NH
Times
Repeat NEXP
Times
NOTE: NEXP: Exposure time in increments of number of lines.
Figure 31. Timing Flow Chart using the Electronic Shutter for Exposure Control
www.onsemi.com
28
KAI−04070
Timing Tables
Frame Timing
This timing table is for transferring charge from the photodiodes to the VCCD. See Figures 32 and 33 for frame timing
diagrams.
Table 20. FRAME TIMING
Full Resolution, High Gain or Low Gain
Device
Pin
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution, High Gain or Low Gain
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution XLDR
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
V1T
F1T
F1B
F1T
F1B
F1T
F1B
V2T
F2T
F4B
F2T
F4B
F2T
F4B
V3T
F3T
F3B
F3T
F3B
F3T
F3B
V4T
F4T
F2B
F4T
F2B
F4T
F2B
V1B
F1B
F1B
F1B
V2B
F2B
F2B
F2B
V3B
F3B
F3B
F3B
V4B
F4B
F4B
F4B
H1Sa
P1
P1Q
P1XL
H1Ba
P1
P1Q
P1XL
H2Sa
P2
P2Q
P2XL
H2Ba
P2
P2Q
P2XL
Ra
RHG/RLG
RHGQ/RLGQ
RXL
H1Sb
H1Bb
P1
P1
P2
P1Q
P1
H2Sb
P2
P1Q
P1XL
P2Q
P2
P1Q
P2Q
P1XL
P2XL
P2Q
P1XL
P2XL
P2XL
H2Bb
P2
P1
P2
P1
P2Q
P1Q
P2Q
P1Q
P2XL
P1XL
P2XL
P1XL
Rb
RHG/
RLG
(Note 1)
RHG/
RLG
(Note 1)
RHGQ/
RLGQ
(Note 1)
RHGQ/
RLGQ
(Note 1)
RXL
(Note 1)
RXL
(Note 1)
R2ab
R2HG/R2LG
R2HGQ/R2LGQ
R2XL
H1Sc
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H1Bc
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H2Sc
P2
(Note 1)
P2Q
(Note 1)
P2XL
(Note 1)
H2Bc
P2
(Note 1)
P2Q
(Note 1)
P2XL
(Note 1)
Rc
RHG/RLG
(Note 1)
RHGQ/RLGQ
(Note 1)
RXL
(Note 1)
H1Sd
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H1Bd
P1
H2Sd
P2
(Note 1)
P2
P1Q
(Note 1)
P2Q
(Note 1)
P2Q
P1XL
(Note 1)
P2XL
P2XL
(Note 1)
(Note 1)
H2Bd
P2
P1
(Note 1)
P2Q
P1Q
(Note 1)
P2XL
P1XL
(Note 1)
Rd
RHG/
RLG
(Note 1)
(Note 1)
RHGQ/
RLGQ
(Note 1)
(Note 1)
RXL
(Note 1)
(Note 1)
R2cd
R2HG/R2LG
(Note 1)
R2HGQ/R2LGQ
(Note 1)
R2XL
(Note 1)
SHP
(Note 2)
SHP1
SHPQ
(Note 4)
SHD
(Note 2)
SHD1
SHDQ
(Note 5)
1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer
CCD family of products.
2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor.
3. This note intentionally left empty.
4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal.
5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal.
www.onsemi.com
29
KAI−04070
Line Timing
This timing is for transferring one line of charge from the VCCD to the HCCD. See Figure 34, Figure 35, Figure 36 and
Figure 37 for line timing diagrams.
Table 21. LINE TIMING
Full Resolution, High Gain or Low Gain
Device
Pin
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution, High Gain or Low Gain
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution XLDR
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
V1T
L1T
L1B
2 × L1T
2 × L1B
2 × L1T
2 × L1B
V2T
L2T
L4B
2 × L2T
2 × L4B
2 × L2T
2 × L4B
V3T
L3T
L3B
2 × L3T
2 × L3B
2 × L3T
2 × L3B
V4T
L4T
L2B
2 × L4T
2 × L2B
2 × L4T
2 × L2B
V1B
L1B
2 × L1B
2 × L1B
V2B
L2B
2 × L2B
2 × L2B
V3B
L3B
2 × L3B
2 × L3B
V4B
L4B
2 × L4B
2 × L4B
H1Sa
P1L
P1LQ
P1XL
H1Ba
P1L
P1LQ
P1XL
H2Sa
P2L
P2LQ
P2XL
H2Ba
P2L
P2LQ
P2XL
Ra
RHG/RLG
RHGQ/RLGQ
RXL
H1Sb
H1Bb
P1L
P1L
P2L
P1LQ
P1L
H2Sb
P2L
P1LQ
P2LQ
P2L
P1XL
P1LQ
P2LQ
P1XL
P2XL
P2LQ
P1XL
P2XL
P2XL
H2Bb
P2L
P1L
P2L
P1L
P2LQ
P1LQ
P2LQ
P1LQ
P2XL
P1XL
P2XL
P1XL
Rb
RHG/
RLG
(Note 1)
RHG/
RLG
(Note 1)
RHGQ/
RLGQ
(Note 1)
RHGQ/
RLGQ
(Note 1)
RXL
(Note 1)
RXL
(Note 1)
R2ab
R2HG/R2LG
R2HGQ/R2LGQ
R2XL
H1Sc
P1L
(Note 1)
P1LQ
(Note 1)
P1XL
(Note 1)
H1Bc
P1L
(Note 1)
P1LQ
(Note 1)
P1XL
(Note 1)
H2Sc
P2L
(Note 1)
P2LQ
(Note 1)
P2XL
(Note 1)
H2Bc
P2L
(Note 1)
P2LQ
(Note 1)
P2XL
(Note 1)
Rc
RHG/RLG
(Note 1)
RHGQ/RLGQ
(Note 1)
RXL
(Note 1)
H1Sd
P1L
(Note 1)
P1LQ
(Note 1)
P1XL
(Note 1)
H1Bd
P1L
H2Sd
P2L
(Note 1)
P2L
P1LQ
(Note 1)
P2LQ
(Note 1)
P2LQ
P1XL
(Note 1)
P2XL
P2XL
(Note 1)
(Note 1)
H2Bd
P2L
P1L
(Note 1)
P2LQ
P1LQ
(Note 1)
P2XL
P1XL
(Note 1)
Rd
RHG/
RLG
(Note 1)
(Note 1)
RHGQ/
RLGQ
(Note 1)
(Note 1)
RXL
(Note 1)
(Note 1)
R2cd
R2HG/R2LG
(Note 1)
R2HGQ/R2LGQ
(Note 1)
R2XL
(Note 1)
SHP
(Note 2)
SHP1
SHPQ
(Note 4)
SHD
(Note 2)
SHD1
SHDQ
(Note 5)
1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer
CCD family of products.
2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor.
3. The notation 2× L1B means repeat the L1B timing twice for every line. This sums two rows into the HCCD.
4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal.
5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal.
www.onsemi.com
30
KAI−04070
Pixel Timing
This timing is for transferring one pixel from the HCCD to the output amplifier.
Table 22. PIXEL TIMING
Full Resolution, High Gain or Low Gain
Device
Pin
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution, High Gain or Low Gain
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
Single
VOUTa
1/4 Resolution XLDR
Dual
VOUTa
VOUTc
Quad
Dual
VOUTa
VOUTb
V1T
−8 V
−8 V
−8 V
V2T
−8 V
−8 V
−8 V
V3T
0V
0V
0V
V4T
0V
0V
0V
V1B
−8 V
−8 V
−8 V
V2B
0V
0V
0V
V3B
0V
0V
0V
V4B
−8 V
−8 V
−8 V
H1Sa
P1
P1Q
P1XL
H1Ba
P1
P1Q
P1XL
H2Sa
P2
P2Q
P2XL
H2Ba
P2
P2Q
P2XL
Ra
RHG/RLG
RHGQ/RLGQ
RXL
H1Sb
H1Bb
P1
P1
P2
P1Q
P1
H2Sb
P2
P1Q
P1XL
P2Q
P2
Single
VOUTa
P1Q
P2Q
P1XL
P2XL
P2Q
P1XL
P2XL
P2XL
H2Bb
P2
P1
P2
P1
P2Q
P1Q
P2Q
P1Q
P2XL
P1XL
P2XL
P1XL
Rb
RHG/
RLG
(Note 1)
RHG/
RLG
(Note 1)
RHGQ/
RLGQ
(Note 1)
RHGQ/
RLGQ
(Note 1)
RXL
(Note 1)
RXL
(Note 1)
R2ab
R2HG/R2LG
R2HGQ/R2LGQ
R2XL
H1Sc
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H1Bc
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H2Sc
P2
(Note 1)
P2Q
(Note 1)
P2XL
(Note 1)
H2Bc
P2
(Note 1)
P2Q
(Note 1)
P2XL
(Note 1)
Rc
RHG/RLG
(Note 1)
RHGQ/RLGQ
(Note 1)
RXL
(Note 1)
H1Sd
P1
(Note 1)
P1Q
(Note 1)
P1XL
(Note 1)
H1Bd
P1
H2Sd
P2
(Note 1)
P2
P1Q
(Note 1)
P2Q
(Note 1)
P2Q
P1XL
(Note 1)
P2XL
P2XL
(Note 1)
(Note 1)
H2Bd
P2
P1
(Note 1)
P2Q
P1Q
(Note 1)
P2XL
P1XL
(Note 1)
Rd
RHG/
RLG
(Note 1)
(Note 1)
RHGQ/
RLGQ
(Note 1)
(Note 1)
RXL
(Note 1)
(Note 1)
R2cd
R2HG/R2LG
(Note 1)
R2HGQ/R2LGQ
(Note 1)
R2XL
(Note 1)
SHP
(Note 2)
SHP1
SHPQ
(Note 4)
SHD
(Note 2)
SHD1
SHDQ
(Note 5)
1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer
CCD family of products.
2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor.
3. This note intentionally left empty.
4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal.
5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal.
www.onsemi.com
31
KAI−04070
Timing Diagrams
The charge in the photodiodes its transfer to the VCCD on
the rising edge of the +12 V pulse and is completed by the
falling edge of the +12 V pulsed on F1T and F1B. During the
time period when F1T and F1B are at +12 V (tPD)
anti-blooming protection is disabled. The photodiode
integration time ends on the falling edge of the +12 V pulse.
Frame Timing − Quadrant and Dual VOUTa/VOUTc Readout Modes
Frame Timing
Device
Pin
V1T
Pattern
tV
2
tV
2
tV
2
t3P
tPD
t3D
tV
2
tV
2
tV
2
tV
2
+12 V
0V
F1T
−8 V
0V
V2T
F2T
−8 V
0V
V3T
F3T
−8 V
0V
V4T
F4T
−8 V
+12 V
V1B
0V
F1B
−8 V
0V
V2B
F2B
−8 V
0V
V3B
F3B
−8 V
0V
V4B
F4B
−8 V
tV
2
tV
2
tV
2
Pixel Timing
t3P
tPD
t3D
tV
2
tV
2
tV
2
tV
2
Frame Timing
NOTE: See Table 20 for pin assignments.
Figure 32. Frame Timing Diagram Quadrant and Dual VOUTa/VOUTc Readout Modes
www.onsemi.com
32
Line Timing
KAI−04070
Frame Timing − Single and Dual VOUTa/VOUTb Readout Modes
Frame Timing
Device
Pin
V1T
Pattern
tV
2
tV
2
tV
2
t3P
tPD
t3D
tV
2
tV
2
tV
2
tV
2
+12 V
0V
F1B
−8 V
0V
V2T
F4B
−8 V
0V
V3T
F3B
−8 V
0V
V4T
F2B
−8 V
+12 V
V1B
0V
F1B
−8 V
0V
V2B
F2B
−8 V
0V
V3B
F3B
−8 V
0V
V4B
F4B
−8 V
tV
2
tV
2
tV
2
Pixel Timing
t3P
tPD
t3D
tV
2
tV
2
tV
2
Frame Timing
NOTE: See Table 20 for pin assignments.
Figure 33. Frame Timing Diagram Single and Dual VOUTa/VOUTb Readout Modes
www.onsemi.com
33
tV
2
Line Timing
KAI−04070
Line Timing −Full Resolution − Quadrant and Dual VOUTa/VOUTc Readout Modes
Line Timing
Time Duration is 4 ⋅ tV
Device
Pin
tV
2
Pattern
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
0V
V1T
L1T
−8 V
0V
V2T
L2T
−8 V
0V
V3T
L3T
−8 V
0V
V4T
L4T
−8 V
0V
V1B
L1B
−8 V
0V
V2B
L2B
−8 V
0V
V3B
L3B
−8 V
0V
V4B
L4B
Cl ocks
Hor izont al
−8 V
0V
P1L
−4 V
0V
P2L
−4 V
tV
2
tV
2
tV
2
tV
2
Frame or Pixel Timing
tV
2
Line Timing
tV
2
tV
2
tV
2
Pixel Timing
te
2
NOTE: See Table 21 for pin assignments.
Figure 34. Line Timing Diagram − Full Resolution − Quadrant and Dual VOUTa/VOUTc Readout Modes
www.onsemi.com
34
KAI−04070
Line Timing −Full Resolution − Single and Dual VOUTa/VOUTb Readout Modes
Line Timing
Time Duration is 4 ⋅ tV
Device
Pin
tV
2
Pattern
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
0V
V1T
L1B
−8 V
0V
V2T
L4B
−8 V
0V
V3T
L3B
−8 V
0V
V4T
L2B
−8 V
0V
V1B
L1B
−8 V
0V
V2B
L2B
−8 V
0V
V3B
L3B
−8 V
0V
V4B
L4B
Cl ocks
Hor izont al
−8 V
0V
P1L
−4 V
0V
P2L
−4 V
tV
2
tV
2
tV
2
tV
2
Frame or Pixel Timing
tV
2
Line Timing
tV
2
tV
2
tV
2
Pixel Timing
te
2
NOTE: See Table 21 for pin assignments.
Figure 35. Line Timing Diagram − Full Resolution − Single and Dual VOUTa/VOUTb Readout Modes
www.onsemi.com
35
KAI−04070
Line Timing − Low Gain, High Gain and XLDR 1/4 Resolution − Quadrant and Dual VOUTa/VOUTc Readout Modes
1/4 Resolution Line Timing
Time Duration is 8 ⋅ tV
Device
Pin
Pattern
V1T
L1T
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
0V
−8 V
0V
V2T
L2T
−8 V
0V
V3T
L3T
−8 V
0V
V4T
L4T
−8 V
0V
V1B
L1B
−8 V
0V
V2B
L2B
−8 V
0V
V3B
L3B
−8 V
0V
Hor izont al
Cl ocks
V4B
L4B
−8 V
0V
P1L
−4 V
0V
P2L
−4 V
tV
2
tV
2
tV
2
Frame or Pixel Timing
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
1/4 Resolution Line Timing
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
Pixel Timing
te
2
NOTE: See Table 21 for pin assignments.
Figure 36. Line Timing Diagram − 1/4 Resolution − Quadrant and Dual VOUTa/VOUTc Readout Modes
www.onsemi.com
36
KAI−04070
Line Timing − Low Gain, High Gain and XLDR 1/4 Resolution − Single and Dual VOUTa/VOUTb Readout Modes
1/4 Resolution Line Timing
Time Duration is 8 ⋅ tV
Device
Pin
Pattern
V1T
L1B
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
0V
−8 V
0V
V2T
L4B
−8 V
0V
V3T
L3B
−8 V
0V
V4T
L2B
−8 V
0V
V1B
L1B
−8 V
0V
V2B
L2B
−8 V
0V
V3B
L3B
−8 V
0V
Hor izont al
Cl ocks
V4B
L4B
−8 V
0V
P1L
−4 V
0V
P2L
−4 V
tV
2
tV
2
tV
2
Frame or Pixel Timing
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
1/4 Resolution Line Timing
tV
2
tV
2
tV
2
tV
2
tV
2
tV
2
Pixel Timing
te
2
NOTE: See Table 21 for pin assignments.
Figure 37. Line Timing Diagram − 1/4 Resolution − Single and Dual VOUTa/VOUTb Readout Modes
www.onsemi.com
37
KAI−04070
finished. The HCCD clocks can be run during the electronic
shutter pulse as long as the HCCD does not contain valid
image data.
For short exposures less than one line time, the electronic
shutter pulse can appear inside the frame timing. Any
electronic shutter pulse transition should be tV/2 away from
any VCCD clock transition.
Electronic Shutter Timing Diagrams
The electronic shutter pulse can be inserted at the end of
any line of the HCCD timing. The HCCD should be empty
when the electronic shutter is pulsed. A recommended
position for the electronic shutter is just after the last pixel
is read out of a line. The VCCD clocks should not resume
until at least tV/2 after the electronic shutter pulse has
tV
2
tV
2
tSUB
VES
SUB
VAB
0V
VCCD Clock
−8 V
Figure 38. Electronic Shutter Timing
tFRAME
V1T/V1B
SUB
tINT
Figure 39. Frame/Electrical Shutter Timing
www.onsemi.com
38
KAI−04070
Pixel Timing − Full Resolution − High Gain Pixel Timing
Use this timing to read out every pixel at high gain. If the
sensor is to be permanently operated at high gain, the R2ab
and R2cd pins can be left floating or set to any DC voltage
between +3 V and +5 V. Note the R2ab and R2cd pins are
internally biased to +4.3 V when left floating. The SHP1 and
SHD1 pulses indicate where the camera electronics should
sample the video waveform. The SHP1 and SHD1 pulses are
not applied to the image sensor.
te
Device
Pin
Pattern
VOUTa
Video
Ra
RHG
+3 V
−3 V
+4.2 V
R2a
R2HG
−1.8 V
SHP1
SHD1
0V
Hor izont al
Cl ocks
P1
−4 V
0V
P2
−4 V
tR
Figure 40. Pixel Timing Diagram − Full Resolution − High Gain
www.onsemi.com
39
KAI−04070
Pixel Timing − Full Resolution − Low Gain Pixel Timing
Use this pixel timing to read out every pixel at low gain.
If the sensor is to be permanently operated at low gain, the
Ra, Rb, Rc and Rd pins should be set to any DC voltage
between +3 V and +5 V. The SHP1 and SHD1 pulses
indicate where the camera electronics should sample the
video waveform. The SHP1 and SHD1 pulses are not
applied to the image sensor.
te
Device
Pin
Pattern
VOUTa
Video
Ra
RLG
+3 V
−3 V
+4.2 V
R2a
R2LG
−1.8 V
SHP1
SHD1
0V
Hor izont al
Cl ocks
P1
−4 V
0V
P2
−4 V
tR
Figure 41. Pixel Timing Diagram − Full Resolution − Low Gain
www.onsemi.com
40
KAI−04070
Pixel Timing − 1/4 Resolution − High Gain Pixel Timing
Use this timing to read out two pixels summed on the
output amplifier sense node at high gain. If the sensor is to
be permanently operated at high gain, the R2ab and R2cd
pins can be left floating or set to any DC voltage between
+3 V and +5 V. Note the R2ab and R2cd pins are internally
biased to +4.3 V when left floating. The SHPQ and SHDQ
pulses indicate where the camera electronics should sample
the video waveform. The SHPQ and SHDQ pulses are not
applied to the image sensor.
The Ra, Rb, Rc, and Rd pins are pulsed at half the
frequency of the horizontal CCD clocks. This causes two
pixels to be summed on the output amplifier sense node.
The SHPQ and SHDQ clocks are also half the frequency of
the horizontal CCD clocks.
2 ⋅ te
Device
Pin
Pattern
VOUTa
Video
Ra
RHGQ
+3 V
−3 V
+4.2 V
R2a
R2HGQ
−1.8 V
SHP1
SHD1
Hor izont al
Cl ocks
0V
P1Q
−4 V
0V
P2Q
−4 V
tR
te
Figure 42. Pixel Timing Diagram − 1/4 Resolution − High Gain
www.onsemi.com
41
KAI−04070
Pixel Timing − 1/4 Resolution − Low Gain Pixel Timing
Use this timing to read out two pixels summed on the
output amplifier sense node at low gain. If the sensor is to be
permanently operated at low gain, the Ra, Rb, Rc and Rd
pins can be set to any DC voltage between +3 V and +5 V.
The SHPQ and SHDQ pulses indicate where the camera
electronics should sample the video waveform. The SHPQ
and SHDQ pulses are not applied to the image sensor.
The R2ab and R2cd pins are pulsed at half the frequency
of the horizontal CCD clocks. This causes two pixels to be
summed on the output amplifier sense node. The SHPQ and
SHDQ clocks are also half the frequency of the horizontal
CCD clocks.
2 ⋅ te
Device
Pin
Pattern
VOUTa
Video
Ra
RLGQ
+3 V
−3 V
+4.2 V
R2a
R2LGQ
−1.8 V
SHP1
SHD1
Hor izont al
Cl ocks
0V
P1Q
−4 V
0V
P2Q
−4 V
tR
te
Figure 43. Pixel Timing Diagram − 1/4 Resolution − Low Gain
www.onsemi.com
42
KAI−04070
XLDR Pixel Timing
To operate the sensor in extended linear dynamic range
(XLDR) mode, the following pixel timing should be used.
This mode requires two sets of analog front end (AFE) signal
processing electronic units for each output. As shown in
Figure 44 one AFE samples the pixel at low gain (SHPLG
and SHDLG) and the other AFE samples the pixel at high
gain (SHPHG and SHDHG).
Two HCCD pixels are summed on the output amplifier
node to obtain enough charge to fully use the 82 dB range of
the XLDR timing. Combined with two-line VCCD
summing, a total of 160,000 electrons of signal (4 × 40,000)
SHDLG
SHPLG
can be sampled with 12 electrons or less noise. Note that
a linear dynamic range of 82 dB is very large. Ensure that the
camera optics is capable of focusing an 82 dB dynamic
range image on the sensor. Lens flare caused by inexpensive
optics or even dust on the lens will limit the dynamic range.
The timing shown in Figure 46 shows the HCCD not
being clocked at a constant frequency. If the HCCD cannot
be clocked at a variable frequency, then the HCCD may be
clocked at a constant frequency (Figure 45) at the expense
of about 33% slower frame rate.
Low Gain AFE
Low Gain
Digital Out
High Gain AFE
High Gain
Digital Out
SHPHG
Caution: In the XLDR mode the
output of the CCD can produce
large signals that may damage
some AFE devices. If there is the
potential for damage to the AFE,
the CCD output should be
electronically attenuated.
SHDHG
Sensor Output
Figure 44. XLDR Timing − AFE Connections Block Diagram
www.onsemi.com
43
KAI−04070
Pixel Timing − 1/4 Resolution − XLDR Pixel Timing − Constant HCCD Timing
4 ⋅ te
Device
Pin
Pattern
VOUTa
Video
Ra
RXL
+3 V
−3 V
+4.2 V
R2a
R2XL
−1.8 V
SHPLG
SHDLG
SHPHG
SHDHG
Hor izont al
Cl ocks
0V
P1XL
−4 V
0V
P2XL
−4 V
tR
te
te
te
te
Figure 45. Pixel Timing Diagram − 1/4 Resolution − XLDR − Constant HCCD Timing
www.onsemi.com
44
KAI−04070
Pixel Timing − 1/4 Resolution − XLDR Pixel Timing − Variable HCCD Timing
3 ⋅ te
Device
Pin
Pattern
VOUTa
Video
Ra
RXL
+3 V
−3 V
+4.2 V
R2a
R2XL
−1.8 V
SHPLG
SHDLG
SHPHG
SHDHG
Hor izont al
Cl ocks
0V
P1XL
−4 V
0V
P2XL
−4 V
tR
te
te
te
Figure 46. Pixel Timing Diagram − 1/4 Resolution − XLDR − Variable HCCD Timing
www.onsemi.com
45
KAI−04070
VCCD Clock Edge Alignment
VVCR
90%
tV
10%
tVF
tVR
tV
tVF
tVR
Figure 47. VCCD Clock Rise Time, Fall Time and Edge Alignment
www.onsemi.com
46
KAI−04070
MECHANICAL INFORMATION
Completed Assembly
Notes:
1. See Ordering Information for marking code.
2. No materials to interfere with clearance through guide holes.
3. Units: mm.
Figure 48. Completed Assembly (1 of 2)
Notes:
1. Optical center of image is nominally at the package center.
2. Units: mm.
Figure 49. Completed Assembly (2 of 2)
www.onsemi.com
47
KAI−04070
Cover Glass
Notes:
1. Substrate = Schott D263T eco.
2. Dust, Scratch, Inclusion Specification: 10 mm maximum size in Zone A.
3. MAR coated both sides.
4. Spectral Transmission:
a. T > 98.0% 420−435 nm
b. T > 99.2% 435−630 nm
c. T > 98.0% 630−680 nm
5. Units: mm.
Figure 50. Cover Glass
www.onsemi.com
48
KAI−04070
Cover Glass Transmission
100
90
80
Transmission (%)
70
60
50
40
30
20
10
0
200
300
400
500
600
700
Wavelength (nm)
Figure 51. Cover Glass Transmission
www.onsemi.com
49
800
900
KAI−04070
REFERENCES
For information on ESD and cover glass care and
cleanliness, please download the Image Sensor Handling
and Best Practices Application Note (AN52561/D) from
www.onsemi.com.
For quality and reliability information, please download
the Quality & Reliability Handbook (HBD851/D) from
www.onsemi.com.
For information on device numbering and ordering codes,
please download the Device Nomenclature technical note
(TND310/D) from www.onsemi.com.
For information on environmental exposure, please
download the Using Interline CCD Image Sensors in High
Intensity Lighting Conditions Application Note
(AND9183/D) from www.onsemi.com.
For information on Standard terms and Conditions of
Sale, please download Terms and Conditions from
www.onsemi.com.
For information on soldering recommendations, please
download the Soldering and Mounting Techniques
Reference
Manual
(SOLDERRM/D)
from
www.onsemi.com.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
50
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
KAI−04070/D