PI3VDP411LS

PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Features
Description
ÎÎConverts low-swing AC coupled differential input to HDMI™
Pericom Semiconductor’s PI3VDP411LS provides the ability to use a Dual-mode DP transmitter in HDMI™ mode.
This flexibility provides the user a choice of how to connect to
their favorite display. All sinal paths accept AC coupled
video signals. The PI3VDP411LS converts this AC coupled signal
into an HDMI rev 1.3 compliant signal with proper signal swing.
This conversion is automatic and transparent to the user.
rev 1.3 compliant open-drain current steering Rx terminated
differential output
ÎÎHDMI level shifting operation up to 2.5Gbps per lane
(250MHz pixel clock)
ÎÎIntegrated 50-ohm termination resistors for AC-coupled
differential inputs.
ÎÎEnable/Disable feature to turn off TMDS outputs to enter
The PI3VDP411LS supports up to 2.5Gbps, which provides 12bits of color depth per channel, as indicated in HDMI rev 1.3.
low-power state.
ÎÎOutput slew rate control on TMDS outputs to minimize EMI.
ÎÎTransparent operation: no re-timing or configuration
required.
1
VDD
HPD_SINK
OE#
GND
GND
DDC_EN
30
SDA_SINK
VDD
31
29
28
27
26
25
24
IN_D1-
38
23
OUT_D1-
IN_D1+
39
22
OUT_D1+
VDD
GND
40
21
IN_D2-
41
20
OUT_D2-
IN_D2+
42
19
OUT_D2+
GND
43
18
GND
IN_D3-
44
17
OUT_D3-
IN_D3+
45
16
OUT_D3+
VDD
46
15
VDD
IN_D4-
47
14
OUT_D4-
13
12
OUT_D4+
5
6
7
8
9
10
11
VDD
4
OC_3
3
SCL_SOURCE
2
SDA_SOURCE
1
OC_2(REXT )
48
GND
GND
VDD
IN_D4+
11-0083
32
HPD_SOURCE
àà – 48 TQFN, 7mm × 7mm (ZDE)
àà – 48 TQFN, 7mm x 7mm (ZBE)
33
GND
ÎÎPackaging (Pb-Free & Green)
34
OC_1
low" when no display is plugged in
35
37
OC_0
ÎÎIntegrated pull-down on HPD_sink input guarantees "input
36
GND
GND
ÎÎLevel shifter for HPD signal from HDMI/DVI connector
VDD
source side
EQ_0
ÎÎDDC level shifters from 5V from sink side down to 3.3V on
GND
I/O pins (IN_x and OUT_x) per IEC61000-4-2 test spec, level 4
EQ_1
ÎÎIntegrated ESD protection to 8kV contact on all high speed
SCL_SINK
Pin Configuration 48-Pin TQFN (ZDE/ZBE)
ÎÎ3.3 Power supply required.
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Block Diagram
OE#
OUTx_D4+
OUTx_D4-
0V
INx_D4+
INx_D4-
Rx
OUTx_D3+
OUTx_D3-
0V
INx_D3+
INx_D3-
Rx
OUTx_D2+
OUTx_D2-
0V
INx_D2+
INx_D2-
Rx
OUTx_D1+
OUTx_D1-
0V
INx_D1+
INx_D1-
HPD_SOURCE
Rx
HPD_SINK
HPD
DDC_EN (0V TO 3.3V)
SCL_SINK
SCL_SOURCE
SDA_SINK
SDA_SOURCE
(times 2)
x = 1 or 2
11-0083
2
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.)
Note: Stresses greater than those listed under MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
Storage Temperature.....................................–65°C to +150°C
Supply Voltage to Ground Potential.............–0.5V to +5V
DC Input Voltage..........................................–0.5V to VDD
DC Output Current .......................................120mA
Power Dissipation .........................................1.0W
Table 2: Signal Descriptions
Pin Name
Type
Description
Enable for level shifter path
5.5V tolerant low-voltage singleended input
OE#
OE#
IN_D Termination
OUT_D Outputs
1
>100KΩ
High-Z
0
50Ω
Active
IN_D4+
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D4+
makes a differential pair with IN_D4–.
IN_D4–
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D4–
makes a differential pair with IN_D4+.
IN_D3+
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D3+
makes a differential pair with IN_D3–.
IN_D3–
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D3–
makes a differential pair with IN_D3+.
IN_D2+
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D2+
makes a differential pair with IN_D2–.
IN_D2–
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D2–
makes a differential pair with IN_D2+.
IN_D1+
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D1+
makes a differential pair with IN_D1–.
IN_D1–
Differential input
Low-swing diff input from GMCH PCIE outputs. IN_D1–
makes a differential pair with IN_D1+.
OUT_D4+
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D4+ makes a differential output signal with OUT_D4–.
OUT_D4–
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D4– makes a differential output signal with OUT_D4+.
OUT_D3+
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D3+ makes a differential output signal with OUT_D3–.
OUT_D3–
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D3– makes a differential output signal with OUT_D3+.
(Continued)
11-0083
3
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Pin Name
Type
Description
OUT_D2+
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D2+ makes a differential output signal with OUT_D2–.
OUT_D2–
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D2– makes a differential output signal with OUT_D2+.
OUT_D1+
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D1+ makes a differential output signal with OUT_D1–.
OUT_D1–
TMDS Differential output
HDMI 1.3 compliant TMDS output. OUT_D1– makes a differential output signal with OUT_D1+.
HPD_SINK
5V tolerance single-ended input
Low Frequency, 0V to 5V (nominal) input signal. This signal comes from the HDMI connector. Voltage High indicates
"plugged" state; voltage low indicated
"unplugged". HPD_SINK is pulled down by an
integrated 100K ohm put-down resistor.
HPD_SOURCE
3.3V single-ended output
HPD_SOURCE: 0V to 3.3V (nominal) output signal. This is
level-shifted version of the HPD_SINK signal.
SCL_SOURCE
Single-ended 3.3V open-drain DDC
I/O
3.3V DDC Data I/O. Pulled up by external termination to 3.3V.
Connected to SCL_SINK through voltage-limiting integrated
NMOS passgate.
SDA_SOURCE
Single-ended 3.3V open-drain DDC
I/O
3.3V DDC Data I/O. Pulled up by external termination to 3.3V.
Connected to SDA_SINK through voltage-limiting integrated
NMOS passgate.
SCL_SINK
Single-ended 5V open-drain DDC I/O
5V DDC Clock I/O. Pulled up by external termination to 5V.
Connected to SCL_SOURCE through voltage-limiting integrated NMOS passgate.
SDA_SINK
Single-ended 5V open-drain DDC I/O
5V DDC Data I/O. Pulled up by external termination to 5V.
Connected to SDA_SOURCE through voltage-limiting integrated NMOS passgate.
Enables bias voltage to the DDC passgate level shifter gates. (May
be implemented as a bias voltage connection to the DDC pass
gates themselves.)
DDC_EN
VDD
OC_2
(REXT)
11-0083
5.0V tolerant Single-ended input
DDC_EN
Passgate
0V
Disabled
3.3V
Enabled
3.3V DC Supply
3.3V ± 10%
3.3V single-ended control input
Acceptable connections to OC_1 (REXT) pin are: Resistor to
GND; Resistor to 3.3V; NC. (Resistor should be 0-ohm).
4
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Pin Name
Type
Description
OC_3
Analog connection to external compo- Acceptable connections to OC_3 pin are: short to 3.3V or to
nent or supply
GND; NC.
OC_0
OC_1
Output and Input jitter elimination
control
EQ_0
EQ_1
Control pins are to enable Jitter elimination features.
For normal operation these pins are tied GND or to VDD. Please
see the truth tables for more information.
Truth Table 1
OC_3(2)
OC_2(1)
OC_1(1)
OC_0(1)
Vswing (mV)
Pre/De-emphasis
0
0
0
0
500
0
0
0
0
1
600
0
0
0
1
0
750
0
0
0
1
1
1000
0
0
1
0
0
500
0
0
1
0
1
500
1.5dB
0
1
1
0
500
3.5dB
0
1
1
1
500
6dB
1
0
0
0
400
0
1
0
0
1
400
3.5dB
1
0
1
0
400
6dB
1
0
1
1
400
9dB
1
1
0
0
1000
0
1
1
0
1
1000
-3.5dB
1
1
1
0
1000
-6dB
1
1
1
1
1000
-9dB
Truth Table 2
EQ_1(2)
EQ_0(1)
Equalization @ 1.25GHz (dB)
0
0
3
0
1
6
1
0
9
1
1
12
Notes:
1) These signals have internal 100kW pull-ups.
2) For 48-TQFN package, these signals have internal 100kW pull-ups, with external connection.
11-0083
5
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Electrical Characteristics
Table 3: Power Supplies and Temperature Range
Symbol
Parameter
Min
Nom
Max
Units
VDD
3.3V Power Supply
3.0
3.3
3.6
V
Comments
ICC
Max Current
100
mA
Total current from
VDD 3.3V supply when
de-emphasis/pre-emphasis is set to 0dB.
ICCQ
Standby Current Consumption
2
mA
OE# = HIGH
TCASE
Case temperature
range for operation with spec.
85
Celcius
-40
Table 4: OE# Description
OE#
Device State
Comments
Asserted (low voltage)
Differential input buffers and output buffers
enabled. Input impedance = 50Ω
Normal functioning state for IN_D to
OUT_D level shifting function.
Low-power state.
Unasserted (high voltage)
Intended for lowest power condition when:
Differential input buffers and termination are
disabled. Differential inputs are in a highimpedance state.
OUT_D level-shifting outputs are disabled.
OUT_D level-shifting outputs are in highimpedence state.
Internal bias currents are turned off.
11-0083
6
•
No display is plugged in or
•
The level shifted data path is disabled
HPD_SINK input and HPD_SOURCE
output are not affected by OE# SCL_
SOURCE, SCL_SINK, SDA_SOURCE and
SDA_SINK signals and functions are not
affected by OE#
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Table 5: Differential Input Characteristics for IN_D and RX_IN signals
Symbol
Parameter
Min
Tbit
Unit Interval
360
VRX-DIFFp-p
Differential Input Peak to
Peak Voltage
0.175
TRX-EYE
Minimum Eye Width at
IN_D input pair
0.8
Nom Max
Units Comments
ps
1.200
V
Tbit
100
Common Mode Input
Voltage
Applies to IN_D and RX_IN signals
The level shifter may add a maximum of 0.02UI
jitter
mV
VRX-CM-DC = DC(avg) of|VRX-D+ + VRXD-|/2
VCM-AC-pp includes all frequencies above 30
kHz.
ZRX-DC
40
VRX-Bias
0
ZRX-HIGH-Z
100
11-0083
VRX-DIFFp-p=2'|VRX-D+ x VRX-D-|
VCM-AC-pp = |VRX-D+ + VRX-D-|/2 - VRXCM-DC.
AC Peak
VCM-AC-pp
Tbit is determined by the display mode. Nominal bit rate ranges from 250Mbps to 2.5Gbps
per lane. Nominal Tbit at 2.5 Gbps=400ps.
360ps=400ps-10%
50
60
Ω
Required IN_D+ as well as IN_D- DC impedance (50Ω ± 20% tolerance).
2.0
V
Intended to limit power-up stress on chipset's
PCIE output buffers.
kΩ
Differential inputs must be in a high impedance
state when OE# is HIGH.
7
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
TMDS Outputs
The level shifter's TMDS outputs are required to meet HDMI 1.3 specifications.
The HDMI 1.3 Specification is assumed to be the correct reference in instances where this document conflicts with the HDMI 1.3
specification.
Table 6: Differential Output Characteristics for TMDS_OUT signals
Symbol
Parameter
Min
Nom
Max
Units
Comments
VH
Single-ended
high level output
voltage
VDD-10mV
VDD
VDD+10mV
V
VDD is the DC termination
voltage in the HDMI or DVI
Sink. VDD is nominally 3.3V
VL
Single-ended
low level output
voltage
VDD-600mV
VDD-500mV
VDD-400mV
V
The open-drain output pulls
down from VDD.
VSWING
Single-ended out450mV
put swing voltage
500mV
600mV
V
Swing down from TMDS
termination voltage (3.3V ±
10%)
IOFF
Single-ended
current in high-Z
state
50
µA
Measured with TMDS
outputs pulled up to VDD
Max _(3.6V) through 50Ω
resistors.
TR
Rise time
125ps
0.4Tbit
ps
Max Rise/Fall time @2.7Gbps
= 148ps. 125ps = 148-15%
TF
Fall time
125ps
0.4Tbit
ps
Max Rise/Fall time @2.7Gbps
= 148ps. 125ps = 148-15%
ps
This differential skew budget
is in addition to the skew
presented between D+ and
D- paired input pins. HDMI
revision 1.3 source allowable
intra-pair skew is 0.15Tbit.
ps
This lane-to-lane skew budget
is in addition to skew between differential input pairs
ps
Jitter budget for TMDS signals as they pass through the
level shifter. 25ps = 0.056 Tbit
at 2.25 Gb/s
TSKEW-INTRA
Intra-pair
TSKEW-INTER
Inter-pair laneto-lane output
skew
TJIT
Jitter added to
TMDS signals
11-0083
30
differential skew
100
25
8
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
TMDS Output Oscillation Elimination
The inputs do not incorporate a squelch circuit. Therefore, we reccomend the input to be externally biased to prevent output oscillation. Pericom reccomends to add a 1.5Kohm pull-up to the CLK- input.
VBIAS
3.3V
1.5Kohm
RINT
RINT
DMDP
Receiver
TMDS
Driver
SS
RT
AVDD
SS
RT
TMDS Input Fail-Safe Recommendation
11-0083
9
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Table 8: HPD Input Characteristics
Symbol
VIH-HPD
Parameter
Input High Level
Min
Nom
Max
Units
Comments
2.0
5.0
5.3
V
Low-speed input changes state on cable plug/
unplug
0.8
V
70
μA
Measured with HPD_sink at VIH-HPD max
and VIL-HPD min
VDD = 3.3V ± 10%
VIL-HPD
HPD_sink Input Low
Level
IIN-HPD
HPD_sink Input
Leakage Current
VOH-HPDB
HPD_sink Output
High-Level
2.5
VDD
V
VOL-HPDB
HPD_sink Output
Low-Level
0
0.02
V
THPD
HPD_sink to HPD_
source propagation
delay
200
ns
Time from HPD_sink changing state to
HPD_source changing state. Includes HPD_
source rise/fall time
TRF-HPDB
HPD_source rise/fall
time
20
ns
Time required to transition from VOH-HPDB
to VOL-HPDB or from VOL-HPDB to VOH-HPDB
0
1
Table 9: OE# Input and DDC_EN
Symbol
Parameter
Min
VIH
Input High Level
2.0
VIL
Input Low Level
0
IIN
Input Leakage Current
Nom Max
Units
Comments
VDD
V
TMDS enable input changes state on
cable plug/unplug
0.8
V
10
μA
Measured with input at VIH-EN max and
VIL-EN min
Table 10: Termination Resistors
Symbol
Parameter
Min
Nom
Max
Units
Comments
R HPD
HPD_sink input pulldown resistor.
80K
100k
120K
Ω
Guarantees HPD_sink is LOW when no
display is plugged in.
11-0083
10
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Recommended Power Supply Decoupling Circuit
Figure 1 is the recommended power supply decoupling circuit configuration. It is recommended to put 0.1µF decoupling capacitors on
each VDD pins of our part, there are four 0.1µF decoupling capacitors are put in Figure 1 with an assumption of only four VDD pins
on our part, if there is more or less VDD pins on our Pericom parts, the number of 0.1µF decoupling capacitors should be adjusted
according to the actual number of VDD pins. On top of 0.1µF decoupling capacitors on each VDD pins, it is recommended to put a
10µF decoupling capacitor near our part’s VDD, it is for stabilizing the power supply for our part. Ferrite bead is also recommended
for isolating the power supply for our part and other power supplies in other parts of the circuit. But, it is optional and depends on the
power supply conditions of other circuits.
10µF
Ferrite Bead
From main
power supply
0.1µF
V DD
0.1µF
V DD
P e r ic o m P a r t
0.1µF
V DD
0.1µF
V DD
Figure 1 Recommended Power Supply Decoupling Circuit Diagram
11-0083
11
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
Requirements on the Decoupling Capacitors
There is no special requirement on the material of the capacitors. Ceramic capacitors are generally being used with typically materials of X5R or X7R.
Layout and Decoupling CapacitorPlacement Consideration
i. Each 0.1µF decoupling capacitor should be placed as close as possible to each VDD pin.
ii. VDD and GND planes should be used to provide a low impedance path for power and ground.
iii. Via holes should be placed to connect to VDD and GND planes directly.
iv. Trace should be as wide as possible
v. Trace should be as short as possible.
vi. The placement of decoupling capacitor and the way of routing trace should consider the power flowing criteria.
vii. 10µF capacitor should also be placed closed to our part and should be placed in the middle location of 0.1µF capacitors.
viii.Avoid the large current circuit placed close to our part; especially when it is shared the same VDD and GND planes. Since large
current flowing on our VDD or GND planes will generate a potential variation on the VDD or GND of our part.
Bypass noise
V DD P la ne
Power Flow
G N D P la ne
0 .1 uF
P e r ic o m P a r t
Figure 2 Layout and Decoupling Capacitor Placement Diagram
11-0083
12
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
1
Notes:
1. All dimensions are in millimeters, angles are in degrees.
2. Refer JEDEC MO-220/VKKD
3. Thermal Pad Soldering Area
4. Depending on the method of lead termination at the edge of the package,
pull back maybe present.
5. Recommended Land Pattern is for reference only.
DATE: 02/12/09
DESCRIPTION: 48-Contact, Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE: ZD (ZD48)
DOCUMENT CONTROL #: PD-2045
REVISION: D
09-0117
11-0083
13
PS8913E
07/12/11
PI3VDP411LS
Digital Video Level Shifter from AC Coupled
Digital Video Input to a DVI/HDMI™ Transmitter
UNIT: mm
1
Notes:
1. All dimensions are in millimeters, angles are in degrees.
2. Coplanarity applies to the exposed thermal pad as well as the terminals.
3. Refer JEDEC MO-220
4. Recommended land pattern is for reference only.
5. Thermal pad soldering area
DATE: 02/11/09
DESCRIPTION: 48-Pin, Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE: ZB48
DOCUMENT CONTROL #: PD-2080
REVISION: A
09-0091
Note:
àà For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php
Ordering Information
Ordering Code
Package Code
Package Description
PI3VDP411LSZBE
ZBE
48-pin Pb-free & Green, TQFN
PI3VDP411LSZDE
ZDE
48-pin Pb-free & Green, TQFN
Notes:
• Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
• E = Pb-free and Green
• Adding an X Suffix = Tape/Reel
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
11-0083
HDMI, High-Definition Multimedia Interface, and Deep Color are trademarks of
HDMI Licensing, LLC in the United States and other countries.
14
PS8913E
07/12/11