CERAMIC DISC CAPACITORS CLASS 2 Series: High K RoHS APPLICATION INTRODUCTION • By-Pass & Coupling • Frequency Discriminating Circuits where Q and Single layer metalized ceramic disc with resin coating (wax impregnated) below 1KV or epoxy coated 1KV up. capacitance stability is not of major importance. • Filtering, Blocking & Timing Range of values extends to much higher values than Class 1 PART NUMBER EXAMPLE 2 ZU 103 M 501 A57 B Temperature Coefficient Capacitance Code Disc 3mm max 10mm min Diameter (D) Packing Code Lead Code Voltage Code Tolerance Code Lead Space (F) ±1mm ±0.05 mm(d) DIMENSIONS (mm) & CAPACITANCE RANGE (F:Standard Lead Spacing. Other lead spacing may be available upon request.) Thickness Voltage Cap (pf) Code 82 100 120 180 200 220 240 300 330 390 470 500 560 680 750 820 1000 1200 1500 1800 2000 2200 2500 2700 3000 3300 3900 5000 5600 6800 7500 8200 10000 15000 20000 22000 33000 47000 56000 100000 820 101 121 181 201 221 241 301 331 391 471 501 561 681 751 821 102 122 152 182 202 222 252 272 302 332 392 502 562 682 752 822 103 153 203 223 333 473 563 104 Y5E Y5F Y5P Z5F 50V/100V ZU YU ZV D=5.5 F=2.5 4.0 mm max. 500V/630V Y5E ZU Y5F YU Y5P Z5F 5.0 2KV 1KV ZV D=6 F=5.0 Y5E Y5F Y5P Z5F ZU YU D=6 F=6.35 Y5E Y5F Y5P Z5F 6.5 3KV ZU D=6 F=6.35 Y5E Y5F Y5P Z5F ZU D=6 F=6.35 8.0 5KV/6KV YP ZU D=8 F=6.35 14.0 10KV YP D=9 F=9.5 D=13 F=12.7 D=7 F=6.35 D=7.5 F=6.35 D=5 F=2.5 D=8 F=6.35 D=6 F=5.0 D=8.5 F=6.35 D=6.5 F=5.0 D=8.5 F=6.35 D=7.5 F=5.0 D=6 F=5.0 D=10 F=5.0 D=11.5 F=5.0 D=8 F=5.0 D=15 F=5.0 D=10 F=5.0 D=17 F=9.5 D=12.5 D=16 F=9.5 D=20 D=7 F=5.0 D=9.5 F=5.0 D=11 D=13 D=17 D=6 F=6.35 D=7 F=6.35 D=6 F=6.35 D=7 F=6.35 D=12 F=9.5 D=8 F=6.35 D=10 F=6.35 D=16 F=12.7 D=10 F=6.35 D=15 F=9.5 D=9 F=6.35 D=10 F=6.35 D=14 F=9.5 D=15 F=9.5 D=14 F=12.7 D=8 F=6.35 D=10 Ff=9.5 D=6.5 F=5.0 D=5.5 F=2.5 D=7 F=6.35 D=7 F=6.35 D=10 F=6.35 D=15 F=12.7 D=10 F=9.5 D=10 F=6.35 D=15 F=9.5 D=13 F=9.5 D=11 F=9.5 D=10 F=6.35 D=8 F=6.35 D=12 F=9.5 D=10.5 F=6.35 D=17 F=9.5 D=12 F=9.5 D=13 F=9.5 D=23 F=9.5 D=15 F=9.5 D=23 D=15 F=9.5 D=18 F=9.5 D=10 F=9.5 D=14 F=9.5 D=15 F=9.5 D=14 F=9.5 D=18 F=9.5 D=25 F=9.5 Page 1 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1BE02 2012.03.08 CERAMIC DISC CAPACITORS CLASS 2 Series: High K TEMPERATURE COEFFICIENT CODE ELECTRICAL CHARACTERISTICS Technical Data Capacitance Operating Temperature Dissipation Factor (tan S) Insulation Resistance Encapsulation Solderability of Leads Condition Measured at 1KHz 1.0 ~ 5.0 VRMS, 25°C X7R Y5E, Y5P Z5U, Z5V X7R, Y5E, Y5P, Z5U Z5V Rated Voltage at 25°C + >°C and 70% R.H. max RoHS Specification 80pF ~ 0.1µF -55°C ~ +125°C -30°C ~ +85°C -10°C ~ +85°C < 0.025 < 0.05 >10GΏ or 200MΏ Farad, whichever is less Standard 1KV and higher Phenolic Wax Epoxy Coating at least 75% is covered Solder Temperature 250°C + 5°C Dipping: 3+0.5 sec (Flur shall be used) Code ZU ZV YE YP YU Temperature Characteristics EIA Code Characteristics Z5U +22 to -56% +10 °C to +85°C Z5V +22 to -82% +10 °C to +85°C Y5E '+4.7% -30 °C to +85°C Y5P '+10% -30 °C to +85°C Y5U '+22 to -56% -30 °C to +85°C RADIAL STRAIGHT-LEAD ON TAPE (S56 LEAD CODE) RADIAL KINK-IN ON TAPE (K56 LEAD CODE) *Most Popular Code Dimensions D 11.0 max d 0.6 ±0.05 P 12.7 ±1.0 P0 12.7 ±0.3 P1 3.85 ±0.7 P2 6.35 ±1.3 F 5.0 +0.8 -0.2 Dh 0 ±2.0 W 18.0 +1.0 -0.5 W1 9.0 +0.75 -0.5 W2 3.0 max H 18.0 +3.0 -0 H0 16.0 ±0.5 H1 32.25 max K 1.0 max D0 4.0 ±0.2 t 0.7 ±0.2 L 11.0 max Page 2 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1BE02 2012.03.08 CERAMIC DISC CAPACITORS CLASS 2 Series: High K RoHS REEL PACK (R SUFFIX) TOLERANCE CODE Code Tolerance C ±0.25pF D ±0.5pF F ±1％ G ±2% J ±5% K ±10% M ±20% 53±1 30±1 f360 max AMMO PACK (A SUFFIX) VOLTAGE CODE EXAMPLE 501 500V 500 50V 502 5KV 103 10KV 253±5mm Code WVDC LEAD CODES FOR BULK PACK (CERAMIC DISC ONLY) A-Straight D-Kink Out 3.0mm 4.8mm max 4.8±1mm 25.4mm min m 3m ± 48 Lead Type C-Kink In mm ±5 330 4.8mm max 4.8±1mm F-Special Length Y-Y Formed S & K-Taped See taping specifications 4.0 mm max 4.8 ±1.0 mm above. Per Customer Specification Lead Spacing Wire dia. (±1.00) in mm (±0.05) in mm Code 2 5 6 7 9 0 A P 2.5 5 6.35 7.5 10.0 12.7 15.0 HOW TO MAKE THE LEAD CODE FOR CERAMIC DISC (FOR BULK PACK ONLY) A67B Bulk Wire Dia. Lead Spacing Lead Type Code df 4 0.48 6 0.6 7 0.65 8 0.8 9 1.0 Page 3 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1BE02 2012.03.08