High Performance Ku-Band Low Noise Amplifiers General Information Intended for either indoor or outdoor environments, the CPI Locus Microwave, Inc. L71 Ku-Band Low Noise Amplifier (LNA) provides a combination of superior performance, reliability and cost effectiveness. Features •Outdoor packaging •Integral Fault Alarm 11562 DS Rev B Americas (Head Office) CPI Satcom Products Palo Alto, Ca USA T: +1 (650) 846-3803 F: +1 (650) 424-1744 Europe, Middle East & Africa CPI International Inc. Cham, Switzerland T: +41 (41) 560 7550 F: +41 (41) 560 7551 Europe, Middle East & Africa CPI Europe, Limited Surrey, England T: +44 (1932) 256 930 F: +44 (1932) 241 271 Asia Pacific CPI Asia, Inc. Singapore T: +65 6225 0011 F: +65 9620 5200 www.cpii.com [email protected] L71 Series Low Noise Amplifiers Range Units Notes Electrical Specifications 10.95-12.75 10.70-12.75 GHz Noise Temperature 60 or 65 max. 60 or 65 max. K @+23°C Gain Gain Flatness Gain Slope 50 or 60 min. +/-1.5 max. +/-0.2 max. 50 or 60 min. +/-1.5 max. +/-0.2 max. dB dB dB per full band per 40 MHz P1dB +10 or 20 min. +10 or 20 min. dBm 1.20 typ., 1.25 max. 1.25 typ., 1.50 max. 1.20 typ., 1.25 max. 1.25 typ., 1.50 max. :1 :1 0 max. 0 max. dBm non-damaging Input De-Sense (14.0-14.5 GHz) -30 max. -30 max. dBm normal operation AM/PM Conversion 0.05 max. 0.05 max. °/dB @-5 dBm output Group Delay Linear Parabolic Ripple 0.01 max. 0.001 max. 0.1 max. 0.01 max. 0.001 max. 0.1 max. ns/MHz ns/MHz² ns p-p per 40 MHz per 40 MHz per full band Power Requirement Input Voltage Current +12 to +24 350 nom. +12 to +24 350 nom. VDC mA 110/220 VAC available contact closure contact closure Form ‘C’ current sensing VAC LMI Dwg #11436 Frequency VSWR Input Output Input Overdrive Fault Alarm Mechanical Specifications Outline LMI Dwg #10132 inches Weight 1.1 nom. lbs. Finish paint white other options available Cover N or SMA 6 pin Flange Female MS-type WR75 waveguide 5 psi -40 to +70 °C consult factory for VAC option 100 % with condensation Connectors RF Input RF Output Power/Alarm Pressure Test mate included Environmental Operating Temperature Humidity Seal all connectors using appropriate weatherproofing materials. Failure to seal connectors could result in down time and repair expenses that are not covered under warranty. Specifications are subject to change, at the discretion of CPI Locus Microwave, Inc. www.cpii.com [email protected] 06/13 11562 DS Rev B Outline Drawing Outline Drawing L71 Series Low Noise Amplifiers Model Number Configuration 1 2 3 4 5 6 7 L71xxxx-xxx-xx 1 Frequency 2 Gain 3 P1dB 4 Power 0 = 10.95-12.75 GHz 1 = 10.70-12.75 GHz 5 = 50 dB 6 = 60 dB 1 = 10 dBm 5 = 20 dBm D = 12-24 VDC *1 A = 110/220 VAC 5 Noise Temp 060 K 065 K Federal Standard 6 Input Type 7 Output Type A Accessories B Finish 0 = WR75 Flange S = SMA (F) *1 N = N (F) 0 = None 1 = 6 Pin Mate 2 = 6 Pin Pigtail DC Only 3 = 6 Pin Pigtail AC Only 0 = White 1 = Dark Green 2 = Desert Tan 3 = Beige 4 = Sand 5 = Forest Green 6 = Metalast 37925 34094 33446 37722 33303 34083 *1 NOTE: LNAs ordered as components of a Redundancy system require DC Power and an SMA (F) output connector. Example: 10.95-12.75 GHz, 50 dB Gain, +20 dBm P1dB , DC Power, 60K Noise L 7 1 0 5 5 D - 060 - 0 N Frequency Noise Temperature Gain Output Type Input Type Power P1dB Please confirm configurations against product specifications, and with factory, prior to order. www.cpii.com [email protected] 11562 DS Rev B