SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS JH Chip type, High Ripple Current Series Solvent Proof WV100V High Ripple current Compared with JC series Designed for surface mounting on high density PC board Applicable to automatic insertion machine using carrier tape Complied to the RoHS directive Item Operating temperature range Leakage current max. Capacitance tolerance Dissipation factor max. (at 120Hz, 20 C) Low temperature characteristics (Impedance ratio at 120Hz) Load life (after application of the rated voltage for 2000 hours at 105 C) Characteristics WV100 : -55 ~ +105 C WV160 : -40 ~ +105 C WV100 I = 0.01CV or 3 A whichever is greater (after 2 minutes) WV160 I = 0.04CV + 100 A(after 1 minutes) 20% at 120Hz, 20 C WV tan 6.3 10 16 25 35 50 63 100 160 200 250 400 450 0.28 0.24 0.20 0.16 0.13 0.12 0.10 0.10 0.15 0.15 0.15 0.20 0.20 WV Z-25 C/Z+20 C Z-40 C/Z+20 C Z-55 C/Z+20 C Leakage current Capacitance change tan 6.3 3 8 10 3 5 16 2 4 25 ~ 50 2 3 63 ~ 100 3 4 400 ~ 450 6 10 - 160 ~ 250 3 6 - Less than specified value Within 20% of initial value Less than 200% of specified value After 1000 hours no load test, leakage current, capacitance and tan are same as load life value. The measurement shall be performed at 20 C by the KS C IEC 60384 - 4 Resistance to soldering heat The following specifications shall be satisfied when the capacitors are restored to 20 C after exposing them at 250 C for 10 seconds. Less than specified value Leakage current Within 10% of initial value Capacitance change Less than specified value tan DRAWING Unit : mm -Series code of JH is “G” 86.2) G 6.3 CHIP TYPES Shelf life (at 105 C) DL 6.35.8 6.37.7 86.2 810 1010 12.5 13.5 A 2.4 2.4 3.3 2.9 3.2 4.6 B 6.6 6.6 8.3 8.3 10.3 12.8 C 6.6 6.6 8.3 8.3 10.3 12.8 E 2.2 2.2 2.3 3.1 4.5 4.5 R 0.5~0.8 0.5~0.8 0.5~0.8 0.8~1.1 0.8~1.1 0.8~1.4 Voltage mark for 6.3V is6 10 10) G 810, 12.5) 61 SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS JH series DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT WV F 6.3 10 16 25 35 10 6.35.8 22 57 6.35.8 63 6.35.8 60 6.35.8 72 86.2 114 6.35.8 69 6.35.8 75 86.2 120 810 186 90 6.35.8 90 810 222 810 270 1010 456 675 33 47 100 6.35.8 220 810 242 810 260 1010 495 1010 525 1010 330 810 432 1010 477 1010 660 1010 558 12.513.5 750 470 1010 510 1010 527 1010 735 1010 675 12.513.5 900 680 1010 612 1010 588 12.513.5 750 12.513.5 750 1000 1010 743 1010 825 12.513.5 900 12.513.5 975 1500 1010 840 2200 12.513.5 1095 WV F Ripple current (mA r ms) at 105 C, 120Hz Case size D X L (mm) 50 63 100 10 6.35.8 45 86.2 48 22 86.2 100 810 90 33 810 200 810 47 1010 270 1010 68 1010 315 100 1010 465 220 12.513.5 720 WV F 160 4.7 165 1010 180 195 12.513.5 375 1010 240 12.513.5 450 12.513.5 405 250 1010 65 1010 65 12.513.5 110 22 12.513.5 125 12.513.5 125 33 12.513.5 140 47 135 200 3.3 10 810 400 1010 45 12.513.5 95 12.513.5 450 45 12.513.5 60 Ripple current (mA r ms) at 105 C, 120Hz Case size D X L (mm) 68 100 FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT 62 Frequency 50Hz 120Hz 300Hz 1kHz 10kHz Coefficient 0.70 1.00 1.17 1.36 1.50