规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW RESONATOR MODEL NO 型 号： HDR433M2 S6 PREPARED 编 制： 王景虹 CHECKED 审 核： APPROVED 批 准： 王为标 D A T E 日 期： 邓攀 2011-4-29 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW RESONATOR HDR433M2 SMD-6 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW RESONATOR HDR433M2 SMD-6 1. Scope This specification shall cover the characteristics of 1-port SAW resonator with R433M2 used for remote-control security. 2. Electrical Specification 2.1 Maximum Rating DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature Source Power 10V 10V 50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 0dBm 2.2 Electronic Characteristics Item Center Frequency Insertion Loss Unload Q 50Ω Loaded Q Temperature Turnover Temperature Stability Freq.temp.Coefficient Frequency Aging DC. Insulation Resistance Motional Resistance R1 RF Equivalent Motional Inductance L1 RLC Model Motional Capacitance C1 Transducer Static Capacitance C0 Unites MHz dB Quality Factor www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 ℃ ppm/℃ ppm/yr MΩ Ω µH fF pF Minimum 433.845 8000 1000 10 Typical 433.92 1.4 12800 2000 25 0.032 <±10 Maximum 433.995 1.9 17 70.743 1.9018 2.0 26 40 1.0 E-mail:[email protected] Page 3 of 8 SAW RESONATOR HDR433M2 SMD-6 2.3 Equivalent LC Model 3. Test Circuit 4. Dimension 1. HD: Manufacture’s logo 2. 6501: Model code www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW RESONATOR HDR433M2 SMD-6 5. Environment Characteristic 5-1 Thermal Shock: The components shall remain within the electrical specifications after being kept at the condition of heat cycle conditions: TA=-40℃±3℃, TB=85℃±2℃, t1=t2=30min, switch time≤3min& cycle time : 100 times, recovery time: 2h±0.5h. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 2.2. 5-3 Solder ability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2.2 5-4 The Temperature Storage: 5.3.1 High Temperature Storage: The components shall remain within the electrical specifications after being kept at the 85℃±2℃for 96h±4h, recovery time : 2h±0.5h. 5.3.2 Low Temperature Storage: The components shall remain within the electrical specifications after being kept at the –40℃±3℃for 96h±4h, recovery time : 2h±0.5h. 5-5 Humidity test: The components shall remain within the electrical specifications after being kept at the condition of ambient temperature 60℃±2℃, and 90~96% RH for 96h±4h. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m for 3 times. The resonator shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 2 hour each in X, Y and Z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The resonator shall fulfill the specifications in 2.2. 6. Remark 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW RESONATOR HDR433M2 SMD-6 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW RESONATOR HDR433M2 SMD-6 8. Tape Specifications 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit: mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.0 5.5 1.75 4.0 4.0 2.0 Ø1.5 Ø1.0 0.3 1.25 3.3± 3.3± ±0.3 ±0.05 ±0.1 ±0.1 ±0.1 ±0.05 ±0.1 ±0.25 ±0.05 ±0.1 0.1 0.1 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW RESONATOR HDR433M2 SMD-6 [Figure 2] Reel Dimensions www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8