产品规格书 SPECIFICATION

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW RESONATOR
MODEL NO 型 号:
HDR420M2 S6
PREPARED 编 制:
王景虹
CHECKED 审 核:
邓攀
APPROVED 批 准:
王为标
D A T E 日 期:
2011-5-4
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 8
SAW RESONATOR
HDR420M2 SMD-6
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 8
SAW RESONATOR
HDR420M2 SMD-6
1. Scope
This specification shall cover the characteristics of 1-port SAW resonator with R420M2 used for
remote-control security.
2. Electrical Specification
2.1 Maximum Rating
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
Source Power
10V
10V 50Hz/60Hz
-40℃ to +85℃
-45℃ to +85℃
0dBm
2.2 Electronic Characteristics
Item
Center Frequency
Insertion Loss
Unload Q
50Ω Loaded Q
Temperature Turnover Temperature
Stability
Freq.temp.Coefficient
Frequency Aging
DC. Insulation Resistance
Motional Resistance R1
RF
Equivalent Motional Inductance L1
RLC Model Motional Capacitance C1
Transducer Static Capacitance C0
Unites
MHz
dB
Quality Factor
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
℃
ppm/℃
ppm/yr
MΩ
Ω
µH
fF
pF
Minimum
419.925
8000
1000
10
Typical
420.000
1.4
12800
2000
25
0.032
<±10
Maximum
420.075
1.9
17
70.743
1.9018
2.0
26
40
1.0
E-mail:[email protected]
Page 3 of 8
SAW RESONATOR
HDR420M2 SMD-6
2.3 Equivalent LC Model
3. Test Circuit
4. Dimension
1. HD: Manufacture’s logo
2. 640B: Model code
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 8
SAW RESONATOR
HDR420M2 SMD-6
5. Environment Characteristic
5-1 Thermal Shock:
The components shall remain within the electrical specifications after being kept at the
condition of heat cycle conditions: TA=-40℃±3℃, TB=85℃±2℃, t1=t2=30min, switch
time≤3min& cycle time : 100 times, recovery time: 2h±0.5h.
5-2 Resistance to solder heat
Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release
the device into the room conditions for 4 hours. It shall meet the specifications in 2.2.
5-3 Solder ability
Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95%
area of the soldering pad must be covered with new solder. It shall meet the specifications in 2.2
5-4 The Temperature Storage:
5.3.1 High Temperature Storage: The components shall remain within the electrical
specifications after being kept at the 85℃±2℃for 96h±4h, recovery time : 2h±0.5h.
5.3.2 Low Temperature Storage: The components shall remain within the electrical
specifications after being kept at the –40℃±3℃for 96h±4h, recovery time : 2h±0.5h.
5-5 Humidity test:
The components shall remain within the electrical specifications after being kept at the
condition of ambient temperature 60℃±2℃, and 90~96% RH for 96h±4h.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m for 3 times. The
resonator shall fulfill the specifications in 2.2.
5-7 Vibration
Subject the device to the vibration for 2 hour each in X, Y and Z axes with the amplitude of
1.5 mm at 10 to 55 Hz. The resonator shall fulfill the specifications in 2.2.
6. Remark
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of the
component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid
ultrasonic cleaning
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 8
SAW RESONATOR
HDR420M2 SMD-6
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 8
SAW RESONATOR
HDR420M2 SMD-6
8. Tape Specifications
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit: mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.0
5.5
1.75
4.0
4.0
2.0
Ø1.5
Ø1.0
0.3
1.25
3.3±
3.3±
±0.3
±0.05
±0.1
±0.1
±0.1
±0.05
±0.1
±0.25
±0.05
±0.1
0.1
0.1
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 8
SAW RESONATOR
HDR420M2 SMD-6
[Figure 2] Reel Dimensions
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 8 of 8