Product Specification Series: TNC 50Ω TNC Jacks & Plugs TNC-TH – Jack, Straight Orientation, PCB Terminated TNC-CA– Plug, Straight Orientation, Cable Terminated Other configurations available for: Right angle cable-to-board applications Through-hole Termination to various cable types See www.samtec.com for more information. Revision: A Date: July 9, 2014 Page 1 © 2012 Samtec, Inc. Product Specification Series: TNC 50Ω TNC Jacks & Plugs 1.0 SCOPE 1.1 This specification covers performance, testing and quality requirements for Samtec TNC Series 50 ohm Jacks & Plugs. These connectors are available in through-hole. All information contained in this specification is for a right angle jack through-hole connector to a straight plug cable connector unless otherwise noted. 2.0 DETAILED INFORMATION 2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at http://www.samtec.com/rf/50-ohm/tnc.aspx. 3.0 TESTING 3.1 ITEM Terminal Orientation Withstanding voltage RG174 RA ST RG316 SR 1000 DCV RA ST RG178 SR 1000 DCV RA ST RG 58 SR RA 1000 DCV ST SR 1000 DCV 3.2 Electrical: ITEM TEST CONDITION REQUIREMENT STATUS Withstanding Voltage EIA-364-20 (No Flashover, Sparkover, or Breakdown) See Section 3.1 Pass Insulation Resistance EIA-364-21 (5000 MΩ minimum) 15,000 MΩ Pass Contact Resistance (LLCR) EIA-364-23 Δ 15 mΩ maximum (Samtec defined)/ No damage Pass REQUIREMENT STATUS 3.3 Mechanical: ITEM TEST CONDITION Durability EIA-364-09C 100 cycles (w/Env.) 1000 cycles (w/o Env) Pass Random Vibration EIA-364-28 Condition V, Letter B 7.56 G 'RMS', 50 to 2000 Hz, 2 hours per axis, 3 axis total , PSD 0.04 Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Event Detection: No interruption > 1.0 microsecond Pass Mechanical Shock EIA-364-27 100 G, 6 milliseconds, half sine, 12.3 ft/s, 3 shocks/direction, 3 axis (18 total shocks) Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Event Detection: No interruption > 1.0 microsecond Pass Normal Force EIA-364-04 30 grams minimum for gold interface Pass Revision: A Date: July 9, 2014 Page 2 © 2012 Samtec, Inc. Product Specification Series: TNC 50Ω TNC Jacks & Plugs 3.4 Environmental: ITEM REQUIREMENT STATUS Thermal Shock EIA-364-32 Thermal Cycles: 100 (30 minute dwell) Hot Temp: +85°C Cold Temp: -55°C Hot/Cold Transition: Immediate Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 825 VAC IR: >15,000 MΩ Pass Thermal Aging (Temp Life) EIA-364-17 Test Condition 4 @ 105°C Condition B for 250 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 825 VAC IR: >15,000 MΩ Pass Cyclic Humidity EIA-364-31 Test Temp: +25°C to +65°C Relative Humidity: 90 to 95% Test Duration: 240 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 825 VAC IR: >15,000 MΩ Pass Gas Tight EIA-364-36 Gas Exposure: Nitric Acid Vapor Duration: 60 min. Drying Temp.: 50°C +/- 3°C Measurements: Within 1 hour of Exposure LLCR: Δ 15 mΩ Pass Revision: A TEST CONDITION Date: July 9, 2014 Page 3 © 2012 Samtec, Inc. Product Specification Series: TNC 50Ω TNC Jacks & Plugs 4.0 MATED SYSTEM 4.1 Orientations 5.0 HIGH SPEED PERFORMANCE 5.1 Frequency Range: Cable Type TNC Orientation Frequency Range RG174 RA ST RG316 SR DC to 6 GHz RA ST RG178 SR DC to 6 GHz RA ST RG 58 SR DC to 6 GHz RA ST SR DC to 6 GHz 5.2 Impedance: 50 ohm 5.3 Rating: DC to 6 GHz Revision: A Date: July 9, 2014 Page 4 © 2012 Samtec, Inc. Product Specification Series: TNC 50Ω TNC Jacks & Plugs 6.0 APPLICATION INFORMATION 6.1 Mating Torque 6.1.1 Min 4.1 in-lb 6.1.2 Recommended 5 in-lb 6.1.3 Max 6.1 in-lb 6.2 Min Cable Bend Radius: RG174 = 1.00”[25.4mm] RG316 = .50”[12.7mm] RG178 = .40”[10.2mm] RG 58 = 1.90”[48.3mm] 6.3 Cable Retention: 15 LBS (Typical) 7.0 ADDITIONAL RESOURCES 7.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at [email protected] 7.2 For additional information on high speed performance testing, contact our Signal Integrity Group at [email protected] 7.3 For additional processing information, contact our Interconnect Processing Group at [email protected] 7.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental Compliance Group at [email protected] Revision: A Date: July 9, 2014 Page 5 © 2012 Samtec, Inc.